Fe (III) supported on resin as effective catalyst for the heterogeneous oxidation of phenol in aqueous solution

FeIII supported on resin as an effective catalyst for oxidation was prepared and applied for the degradation of aqueous phenol. Phenol was selected as a model pollutant and the catalytic oxidation was carried out in a batch reactor using hydrogen peroxide as the oxidant. The influent factors on oxidation, such as catalyst dosage, H2O2 concentration, pH, and phenol concentration were examined by considering both phenol conversion and chemical oxygen demand (COD) removal. The FeIII-resin catalyst possesses a high oxidation activity for phenol degradation in aqueous solution. The experimental results of this study show that almost 100% phenol conversion and over 80% COD removal can be achieved with the FeIII-resin catalyst catalytic oxidation system. A series of prepared resin were investigated for improving the oxidation efficiency. It was found that the reaction temperature and initial pH in solution significantly affected both of phenol conversion and COD removal efficiency. The activity of the catalyst significantly decreased at high pH, which was similar to the Fenton-like reaction mechanism. Results in this study indicate that the FeIII-resin catalytic oxidation process is an efficient method for the treatment of phenolic wastewater.     

Degradation of aqueous carbon tetrachloride by nanoscale zerovalent copper on a cation resin

Nanoscale zerovalent copper supported on a cation resin was successfully synthesized to enhance the removal of carbon tetrachloride (CCl(4)) from contaminated water. The use of the cation resin as a support prevents the reduction of surface area due to agglomeration of nanoscale zerovalent copper particles. Moreover, the cation resin recycles the copper ions resulting from the reaction between CCl(4) and Cu(0) by simultaneous ion exchange. The decline in the amount of CCl(4) in aqueous solution results from the combined effects of degradation by nanoscale zerovalent copper and sorption by the cation resin; thus the amount of CCl(4) both in aqueous solution and sorbed onto the resin were measured. The pseudo-first-order rate constant normalized by the surface-area and the mass concentration of nanoscale zerovalent copper (k(SA)) was 2.1+/-0.1 x 10(-2)lh(-1)m(-2), approximately twenty times that of commercial powdered zerovalent copper (0.04 mm). Due to the exchange between Cu(2+) and the strongly acidic ions (H(+) or Na(+)), the pH was between 3 and 4 in unbuffered solution and Cu(2+) at the concentration of less than 0.1 mg l(-1) was measured after the dechlorination reaction. In the above-ground application, resin as a support would facilitate the development of a process that could be designed for convenient emplacement and regeneration of porous reductive medium.     

Biosorption of copper(II) from aqueous solutions by pre-treated biomass of marine algae Padina sp

Biosorption of heavy metals can be an effective process for the removal and recovery of heavy metal ions from aqueous solutions. The biomass of marine algae has been reported to have high uptake capacities for a number of heavy metal ions. In this paper, the adsorption properties of a pre-treated biomass of marine algae Padina sp. for copper(II) were investigated. Equilibrium isotherms and kinetics were obtained from batch adsorption experiments. The biosorption capacities were solution pH dependent and the maximum capacity obtained was 0.80 mmol/g at a solution pH of about 5. The biosorption kinetics was found to be fast, with 90% of adsorption within 15 min and equilibrium reached at 30 min. The effects of light metal ions on copper(II) uptake were studied and the presence of light metal ions did not affect copper(II) uptake significantly. Fixed-bed breakthrough curves for copper(II) removal were also obtained. This study demonstrated that the pre-treated biomass of Padina sp. could be used as an effective biosorbent for the treatment of copper(II) containing wastewater streams.     

Studies on hexavalent chromium biosorption by chemically-treated biomass of Ecklonia sp

The biomass of the brown seaweed, Ecklonia sp., is capable of reducing Cr(VI) to Cr(III). However, very little is known about the mechanism of Cr(VI) reduction by the biomass. The aims of the present investigation were to enhance the Cr(VI)-reducing capacity of the biomass using various chemical treatments and to elucidate the mechanisms governing Cr(VI) reduction. Among the various chemical treatments, acid-treatment showed the best performance with regards the improvement of Cr(VI) removal from the aqueous phase, while organic solvent-treatment significantly improved the removal efficiency of total Cr in the equilibrium state. Based on FTIR study, the biomass was subjected to chemical modification of its amino and carboxyl groups, to examine their roles in the Cr(VI) removal from the aqueous phase. Methylation of the amino group significantly decreased the Cr(VI) removal rate, but amination of the carboxyl group significantly increased the Cr(VI) removal rate. Meanwhile, esterification of the carboxyl group and carboxylation of the amino group decreased the Cr(VI) removal rate, but the former showed a more negative effect than the latter. These findings indicated that the amino and carboxyl groups take part in the Cr(VI) removal from the aqueous phase. In conclusion, mechanisms for direct and indirect Cr(VI) removal are proposed, and some aspects for the application of this biomass to Cr(VI) detoxification are discussed.     

新型TCAS吸附树脂对水中Cd^2＋的吸附去除研究

通过静态吸附试验，研究一种由超分子受体化合物磺化硫杂杯芳烃（TCAS）与树脂结合的产物——新型TCAS吸附树脂对重金属Cd^2＋的吸附去除性能，并初步探讨了吸附机理。试验研究结果表明，TCAS吸附树脂对Cd^2＋的饱和吸附量为14．45mg/g。当温度为20℃，0．5gTCAS吸附树脂对10mL浓度为5113g／L的Cd^2＋溶液吸附60min时，Cd^2＋的去除率可达到99％以上。pH值是影响TCAS吸附树脂吸附效果的重要因素，在pH=5—9时，Cd^2＋的去除率随着pH值的升高而增大。在试验范围内，TCAS吸附树脂对Cd^2＋吸附符合Freundlich方程。吸附在TCAS吸附树脂上的Cd^2＋可洗脱回收，TCAS吸附树脂也可再生利用。TCAS吸附树脂对重金属Cd^2＋的吸附机理主要归因于TCAS对Cd^2＋的络合作用。     

Loofa sponge immobilized fungal biosorbent: a robust system for cadmium and other dissolved metal removal from aqueous solution

The potential of loofa sponge discs to immobilize fungal biomass of Phanerochaete chrysosporium (a known biosorbent) was investigated as a low cost biosorbent for the removal of Cd(II) ions from aqueous solution. A comparison of the biosorption of Cd(II) by immobilized and free fungal biomass from 10 to 500 mg l(-1) aqueous solutions showed an increase in uptake of over 19% when the biomass is immobilized (maximum biosorption capacity of 89 and 74 mg Cd(II) g(-1) biomass for immobilized and free biomass respectively at a solution pH of 6). Equilibrium was established within 1h and biosorption was well defined by the Langmuir isotherm model. The immobilized biomass could be regenerated using 50 mM HCl, with up to 99% metal recovery and reused in ten biosorption-desorption cycles without significant loss of capacity. This study suggests that such an immobilized biosorbent system has the potential to be used in the industrial removal/recovery of cadmium and other pollutant metal ions from aqueous solution.     

Production of polyhydroxyalkanoate during treatment of low-phosphorus-content wastewater.

To evaluate whether poly-beta-hydroxyalkanoate (PHA) production and wastewater treatment could be combined in a single biological process, a bench-scale sequencing batch reactor was operated with sequential anaerobic and aerobic stages and removal of excess sludge at different stages of treatment. The reactor treated synthetic wastewater with a high organic and low nutrient content, simulating industrial wastewater. Chemical oxygen demand removal efficiency was more than 90% in all cases. Poly-beta-hydroxyalkanoate accumulation was significant, although it did not appear to be induced by oxygen limitations during the anaerobic stage. Sphaerotilus natans was apparently the dominant PHA-accumulating organism at the end of each reactor run and corresponded to a PHA accumulation of 16 to 20% of the total dry cell mass. Before S. natans dominated the reactors, PHA accumulation was approximately 17% when biomass was removed at the end of the aerobic stage and 6.6% when sludge removal also occurred during the anaerobic stage.     

Lead biosorption and desorption by intact and pretreated spirulina maxima biomass

In order to search for locally available and untried biomaterials in China with high removal capacity of heavy metals from wastewater, the feasibility of Spirulina maxima as biosorbent for lead removal and recovery from aqueous solution was investigated. The lead biosorption was studied by using intact biomass and pretreated biomass of S. maxima. The effects of operational conditions (e.g. pH, contact time, biomass concentration etc.) on lead biosorption were investigated. The biosorption was solution pH dependent and the maximum adsorption was obtained at a solution pH of about 5.5. The adsorption equilibrium was reached in 60 min. The biosorption followed the Freundlich isotherm model. The maximum removal ratios of lead were about 84% in intact biomass and 92% in pretreated biomass. The lead adsorbed could be desorbed effectively by 0.1 M nitric acid, EDTA and hydrochloric acid. The results in this study indicated that pretreated biomass of S. maxima was a promising candidate for removing lead from wastewater.     

Metal uptake capacity of modified Saccharomyces pastorianus biomass from different types of solution

In this paper, we investigate the effect of different biomass pretreatments on metal ion uptake by various biosorbents. Heat-treated as well as caustic-treated and ground biomass of Saccharomyces pastorianus was used to remove copper, lead and cadmium from various solutions. Untreated yeast was used as the control sample. The effect of yeast modification on sorption capacity depended on the different types of heavy metal ions and whether they were in single- or multi-component solutions. The highest uptake of copper and lead from a single-metal solution was obtained from heat-treated cells. Ground biomass was the most efficient at cadmium removal. However, the sorption capacity of the modified biomass did not improve when metal ions were removed from multi-component solutions. Indeed, the results in this paper show that optimizing metal removal from single-cation solutions can lead to decreased sorption capacity in multi-component solutions. Therefore, while adjusting the procedure of biomass modification, not only the nature of the metal ion being sorbed but also the chemical composition of the metal ion solution should be taken into account.     

浮游球衣菌对Pb2+、Cu2+、Zn2+、Cd2+的吸附性能研究

研究了浮游球衣菌（Sphaerotilus natans）在不同吸附条件下对溶液中Pb^2＋、Cu^2＋、Zn^2＋、Cd^2＋的吸附规律。结果表明,Sphaerotilus natans对这4种重金属离子均有一定的吸附作用,并在20min内达到吸附平衡,pH对吸附过程影响较大,pH为5.5时Sphaerotilus natans对这4种金属离子的吸附效果最好,Sphaerotilus natans对它们的吸附选择性为Pb^2＋〉Cu^2＋〉Zn^2＋〉Cd^2＋,Pb^2＋、Cu^2＋能部分置换出已被菌体吸附的Zn^2＋、Cd^2＋。HCI和EDTA溶液可有效地将金属离子从菌体上解吸下来,解吸后的菌体可重复使用。     

Kinetic study of the removal of dimethyl phthalate from an aqueous solution using an anion exchange resin

Phthalate acid esters are becoming an important class of pollutants in wastewaters. This study addresses the kinetics of removal of dimethyl phthalate (DMP) using the anion exchange resin D201-OH from an aqueous solution. The effects of various factors on the removal rate and efficiency were investigated. An overall initial removal rate (OIRR) law and a pseudo first-order kinetic (PFOK) model were also developed. The internal diffusion of DMP within the resin phase of D201-OH is the rate-controlling step. Optimization of the particle size and pore structure of the resin D201-OH, the DMP concentration, and the reaction temperature can improve the DMP removal rate. The hydrolysis reaction of DMP catalyzed by D201-OH indicates an overall reaction order of 1.76, a value that is between the first order and the second order. The apparent activation energy of the reaction is 34.6 kJ/mol, which is below the homogeneous alkaline hydrolysis activation energy of 44.3 kJ/mol. The OIRR law can quantify the initial removal rate under different conditions. The results also show that the theoretical DMP removal efficiency predicted by the PFOK model agrees well with the experimentally determined values. Our research provides valuable insights into the primary parameters influencing the kinetic process, which enables a focused improvement in the removal or hydrolysis rate for similar processes.     

Phytoaccumulation potentials of two biotechnologically propagated ecotypes of Arundo donax in copper-contaminated synthetic wastewater

An in vitro experiment was carried out to evaluate the phytoremediation potentials of two somatic embryo-derived ecotypes of Arundo donax—BL (American ecotype) and 20SZ (Hungarian ecotype)—of copper from synthetic wastewater. The two ecotypes were grown under sterile conditions in tubes containing a nutrient solution supplied with increasing doses of Cu (0, 1, 2, 3, 5, 10, and 26.8 mg L^?1) for 6 weeks. The translocation and bioaccumulation factors and removal rate were estimated. In general, increasing Cu concentration in nutrient solution slightly decreased root, stem and leaf biomass without toxicity symptoms up to 26.8 mg L^?1. Moreover, both ecotypes showed high Cu removal efficiency from aqueous solution. However, Cu removal rate ranged between 96.6 to 98.8 % for BL ecotype and 97 to 100 % for 20SZ ecotype. Data illustrated that both BL and 20SZ ecotypes may be employed to treat Cu-contaminated water bodies up to 26.8 mg L^?1.     

弱碱性树脂吸附-解吸苦味酸

考察了水中苦味酸在弱碱性离子交换树脂D301R上的吸附与解吸。研究了吸附热力学、动力学特性及吸附机理。结果表明,树脂在pH=2.7～10.2时,吸附能力最好。等温平衡吸附遵循Freundlich模型。吸附过程为吸热、熵增的自发过程。吸附动力学符合Lagergren准二级速率方程,颗粒内扩散为吸附速率的主要控制步骤,吸附速率常数为7.23×10-5～1.20×10-4g/(mg.min),吸附活化能为19.4 kJ/mol。树脂上吸附的苦味酸可用HNO3+丙酮混合液定量洗脱,洗脱率达99%。静态吸附和脱附的比较结果证实了吸附过程中存在不可逆化学吸附。树脂对苦味酸的吸附主要是通过静电吸附、酸碱络合吸附、氢键吸附等协同作用来完成的。     

枯草芽孢杆菌对Cu2+的吸附及菌体表面基团分析

以枯草芽孢杆菌(Bacillus subtilis)为生物吸附剂,讨论了其对Cu2+的生物吸附规律,并通过酸碱滴定这一表面分析手段,结合相关软件及傅里叶变换红外光谱(FTIR)分析了菌体表面主要的基团种类及数量.结果表明,枯草芽孢杆菌对Cu2+吸附的最佳条件是:pH为6、吸附时间为24 h,菌悬液用量和Cu2+初始浓度...     

Long-term effects of amendment with liquid swine manure on proton binding behavior of soil humic substances

The acid-base properties of humic acids (HAs) and fulvic acids (FAs) isolated from liquid swine manure (LSM), soils amended with either 90 or 150 m(3)ha(-1)year(-1) of LSM for 7 years, and the corresponding unamended control soil were investigated by a current potentiometric titration method. The non-ideal competitive adsorption (NICA)-Donnan model for proton binding by two classes of binding sites (i.e., carboxylic- and phenolic-type groups) was fit to titration data, and a set of fitting parameters was obtained for each HA and FA sample. The NICA-Donnan model was shown to describe with a great degree of accuracy the behavior of experimental titration datasets, and highlighted important differences in the acid-base properties of the HAs and FAs examined. When compared to the unamended soil HA and FA, LSM-HA and LSM-FA, had smaller acidic functional group contents, larger proton binding affinities of both carboxylic- and phenolic-type groups, smaller heterogeneity of carboxylic-type groups, and smaller, in the case of HA, or similar, in the case of FA, heterogeneity of phenolic-type groups. Amendment with LSM caused a decrease of acidic functional group contents and a slight increase of proton binding affinities of carboxylic- and phenolic-type groups of soil HAs and FAs. Further, LSM application induced a decrease of the heterogeneity of carboxylic-type groups, whereas appeared not to affect substantially the heterogeneity of phenolic-type groups of LSM-amended soil HAs and FAs. These effects were more evident for HAs than for FAs and tended to slightly increase with increasing LSM amendment rate.     

满江红干体对锌离子的生物吸附

以满江红干体为生物吸附剂，研究了不同条件下对废水中Zn²⁺的净化作用。结果表明，满江红干体对Zn²⁺的吸附是一个快速的过程，前5 min的吸附量达到最大吸附量的62.9%，30 min达到吸附平衡；初始pH值对Zn²⁺的吸附有显著的影响，最适pH值为6；随着干体量的增加，吸附率逐渐提高而吸附量则降低；随着Zn²⁺初始浓度的增加，吸附率逐渐降低而吸附量则提高。满江红干体对Zn²⁺的吸附符合Langmuir吸附等温线方程，最大吸附容量达57.5 mg/g。5次吸附解吸循环实验数据表明，重复次数和再生处理对满江红干体的吸附能力没有产生显著影响。因此，满江红干体在处理含Zn²⁺废水中的重复使用是可行的。     

Removal of non-steroidal anti-inflammatory drugs ibuprofen and ketoprofen from water by emulsion liquid membrane

In this work, the removal of the worldwide non-steroidal anti-inflammatory drugs ibuprofen (IBP) and ketoprofen (KTP) by emulsion liquid membrane (ELM) was carried out. An ELM system is made up of hexane as diluent, Span 80 as the surfactant and sodium carbonate as the inner aqueous solution. Effect of experimental conditions that affect the extraction of IBP such as surfactant concentration, emulsification time, sulfuric acid concentration in external phase, acid type in external phase, internal phase concentration, type of internal phase, stirring speed, volume ratio of internal phase to membrane phase, treatment ratio, IBP initial concentration, diluent type and salt was investigated. The obtained results showed that by appropriate selection of the operational parameters, it was possible to extract nearly all of IBP molecules from the feed solution even in the presence of high concentration of salt. Under optimum operating conditions, the efficiencies of IBP removal from distilled water (99.3 %), natural mineral water (97.3 %) and sea water (94.0 %) were comparable, which shows that the ELM treatment process represents a very interesting advanced separation process for the removal of IBP from complex matrices such as natural and sea waters. Under the optimized experimental conditions, approximately 97.4 % KTP was removed in less than 20 min of contact time.     

Selective separation of copper(II) and nickel(II) from aqueous media using the complexation-ultrafiltration process

The polyethylenimine (PEI) as complexing agent was used to study the complexation-ultrafiltration (CP-UF) process in the selective removal of Cu(II) from Ni(II) contained in aqueous media. Preliminary tests showed that optimal chemical conditions for Cu(II) and Ni(II) complexation by the PEI polymer were pH>6.0 and 8.0, respectively, and polymer/metal weight ratio of 3.0 and 6.0, respectively. The effect of some important operating parameters on process selectivity was studied by performing UF tests at different parameters: pH, polymer/metal weight ratio, transmembrane pressure (TMP), and membrane cut-off in a batch experimental set-up. It was observed that process selectivity was achieved by choosing the pH value for obtaining a preferential copper complexation (pH 6.0), and the polymer/metal ratio needed to bound only the copper ion (3.0). The selective separation by UF tests was performed by using both a laboratory aqueous solution and a real aqueous effluent (water from Emoli torrent, Rende (CS)). The Iris 30 membrane at TMP of 200 kPa (2 bar) for both aqueous media gave the best results. A complete nickel recovery was reached, and copper recovery was the highest for this membrane (94% and 92%). Besides at this pressure, a lower water amount was needed to obtain total nickel recovery by diafiltration. A little higher membrane fouling was obtained by using the river effluent due to the presence of dissolved organic and inorganic matter.     

Sorption of arsenate and arsenite anions by iron(III)-poly(hydroxamic acid) complex

Iron(III)-poly(hydroxamic acid) resin complex has been studied for its sorption abilities with respect to arsenate and arsenite anions from an aqueous solution. The complex was found effective in removing the arsenate anion in the pH range of 2.0 to 5.5. The maximum sorption capacity was found to be 1.15 mmol/g. The sorption selectivity showed that arsenate sorption was not affected by chloride, nitrate and sulphate. The resin was tested and found effective for removal of arsenic ions from industrial wastewater samples.     

非均相催化湿式氧化亚甲蓝水溶液的研究

COD为2000 mg/L的亚甲蓝水溶液作为研究对象,用非均相催化湿式氧化技术进行处理,催化剂性能以COD去除率、脱色率以及稳定性来评价.对4种催化剂担体、15种可溶盐活性组分、4种优选铜催化剂的浸渍液浓度进行筛选,并对铜催化剂进行了改性.实验表明,最佳催化剂担体是FSC,活性组分是Cu(NO3)2,并按催化性能对活性组分进行了排序;浸渍液浓度6wt%Cu2 是最佳选择;改性的Cu-Ce/FSC催化剂与Cu/FSC催化剂相比,COD去除率分别为83.9%和84.5%,出水Cu溶出浓度分别为24.1 mg/L和36.1 mg/L,可见改性催化剂与原催化剂的活性相当,但是稳定性却有了大幅度的提高.