Estimating dissolved reactive phosphorus concentration in surface runoff water from major Ontario soils

Phosphorus (P) loss from agricultural land in surface runoff can contribute to eutrophication of surface water. This study was conducted to evaluate a range of environmental and agronomic soil P tests as indicators of potential soil surface runoff dissolved reactive P (DRP) losses from Ontario soils. The soil samples (0- to 20-cm depth) were collected from six soil series in Ontario, with 10 sites each to provide a wide range of soil test P (STP) values. Rainfall simulation studies were conducted following the USEPA National P Research Project protocol. The average DRP concentration (DRP30) in runoff water collected over 30 min after the start of runoff increased (p < 0.001) in either a linear or curvilinear manner with increases in levels of various STPs and estimates of degree of soil P saturation (DPS). Among the 16 measurements of STPs and DPSs assessed, DPS(M3) 2 (Mehlich-3 P/[Mehlich-3 Al + Fe]) (r2 = 0.90), DPS(M3)-3 (Mehlich-3 P/Mehlich-3 Al) (r2 = 0.89), and water-extractable P (WEP) (r2 = 0.89) had the strongest overall relationship with runoff DRP30 across all six soil series. The DPS(M3)-2 and DPS(M3)-3 were equally accurate in predicting runoff DRP30 loss. However, DPS(M3)-3 was preferred as its prediction of DRP30 was soil pH insensitive and simpler in analytical procedure, ifa DPS approach is adopted.     

Relating soil phosphorus to dissolved phosphorus in runoff: a single extraction coefficient for water quality modeling

Phosphorus transport from agricultural soils contributes to eutrophication of fresh waters. Computer modeling can help identify agricultural areas with high potential P transport. Most models use a constant extraction coefficient (i.e., the slope of the linear regression between filterable reactive phosphorus [FRP] in runoff and soil P) to predict dissolved P release from soil to runoff, yet it is unclear how variations in soil properties, management practices, or hydrology affect extraction coefficients. We investigated published data from 17 studies that determined extraction coefficients using Mehlich-3 or Bray-1 soil P (mg kg(-1)), water-extractable soil P (mg kg(-1)), or soil P sorption saturation (%) as determined by ammonium oxalate extraction. Studies represented 31 soils with a variety of management conditions. Extraction coefficients from Mehlich-3 or Bray-1 soil P were not significantly different for 26 of 31 soils, with values ranging from 1.2 to 3.0. Extraction coefficients from water-extractable soil P were not significantly different for 17 of 20 soils, with values ranging from 6.0 to 18.3. The relationship between soil P sorption saturation and runoff FRP (microg L(-1)) was the same for all 10 soils investigated, exhibiting a split-line relationship where runoff FRP rapidly increased at P sorption saturation values greater than 12.5%. Overall, a single extraction coefficient (2.0 for Mehlich-3 P data, 11.2 for water-extractable P data, and a split-line relationship for P sorption saturation data) could be used in water quality models to approximate dissolved P release from soil to runoff for the majority of soil, hydrologic, or management conditions. A test for soil P sorption saturation may provide the most universal approximation, but only for noncalcareous soils.     

Soil testing to predict phosphorus leaching

Subsurface pathways can play an important role in agricultural phosphorus (P) losses that can decrease surface water quality. This study evaluated agronomic and environmental soil tests for predicting P losses in water leaching from undisturbed soils. Intact soil columns were collected for five soil types that a wide range in soil test P. The columns were leached with deionized water, the leachate analyzed for dissolved reactive phosphorus (DRP), and the soils analyzed for water-soluble phosphorus (WSP), 0.01 M CaCl2 P (CaCl2-P), iron-strip phosphorus (FeO-P), and Mehlich-1 and Mehlich-3 extractable P, Al, and Fe. The Mehlich-3 P saturation ratio (M3-PSR) was calculated as the molar ratio of Mehlich-3 extractable P/[Al + Fe]. Leachate DRP was frequently above concentrations associated with eutrophication. For the relationship between DRP in leachate and all of the soil tests used, a change point was determined, below which leachate DRP increased slowly per unit increase in soil test P, and above which leachate DRP increased rapidly. Environmental soil tests (WSP, CaCl2-P, and FeO-P) were slightly better at predicting leachate DRP than agronomic soil tests (Mehlich-1 P, Mehlich-3 P, and the M3-PSR), although the M3-PSR was as good as the environmental soil tests if two outliers were omitted. Our results support the development of Mehlich-3 P and M3-PSR categories for profitable agriculture and environmental protection; however, to most accurately characterize the risk of P loss from soil to water by leaching, soil P testing must be fully integrated with other site properties and P management practices.     

Soil characteristics and phosphorus level effect on phosphorus loss in runoff

The loss of phosphorus (P) in runoff from agricultural soils may accelerate eutrophication in lakes and streams as well as degrade surface water quality. Limited soil specific data exist on the relationship between runoff P and soil P. This study investigated the relationship between runoff dissolved reactive phosphorus (DRP) and soil P for three Oklahoma benchmark soils: Richfield (fine, smectitic, mesic Aridic Argiustoll), Dennis (fine, mixed, active, thermic Aquic Argiudoll), and Kirkland (fine, mixed, superactive, thermic Udertic Paleustoll) series. These soils were selected to represent the most important agricultural soils in Oklahoma across three major land resource areas. Surface soil (0-15 cm) was collected from three designated locations, treated with diammonium phosphate (18-46-0) to establish a wide range of water-soluble phosphorus (WSP) (3.15-230 mg kg(-1)) and Mehlich-3 phosphorus (M3P) (27.8-925 mg kg(-1)). Amended soils were allowed to reach a steady state 210 d before simulated rainfall (75 mm h(-1)). Runoff was collected for 30 min from bare soil boxes (1.0 x 0.42 m and 5% slope) and analyzed for DRP and total P. Soil samples collected immediately before rainfall simulation were analyzed for the following: M3P, WSP, ammonium oxalate P saturation index (PSI(ox)), water-soluble phosphorus saturation index (PSI(WSP)), and phosphorus saturation index calculated from M3P and phosphorus sorption maxima (P(sat)). The DRP in runoff was highly related (p < 0.001) to M3P for individual soil series (r2 > 0.92). Highly significant relationships (p < 0.001) were found between runoff DRP and soil WSP for the individual soil series (r2 > 0.88). Highly significant relationships (p < 0.001) existed between DRP and different P saturation indexes. Significant differences (p < 0.05) among the slopes of the regressions for the DRP-M3P, DRP-WSP, DRP-PSI(ox), DRP-PSI(WSP), and DRP-P(sat) relationships indicate that the relationships are soil specific and phosphorus management decisions should consider soil characteristics.     

Phosphorus leaching in manure-amended Atlantic Coastal Plain soils

Targeting the sources of phosphorus (P) and transport pathways of drainage from agricultural land will assist in the reduction of P loading to surface waters. Our research investigated the vertical movement of P from dairy manure and broiler litter through four Atlantic Coastal Plain soils. A randomized split-plot design with two main-plot tillage treatments (no tillage [NT] and chisel tillage [CH]) and five manure P rate split-plot treatments was used at each location. The split-plot P rates were 0, 100, 200, 300, and 400 kg P ha(-1) yr(-1). Four consecutive years of manure application began at all sites 5 yr before sampling. Soils were sampled to a depth of 150 cm from each split plot in seven depth increments and analyzed for soil test phosphorus (STP), water-extractable soil phosphorus (WSP), and degree of phosphorus saturation (DPS). The DPS of the 0- to 15-cm depths confirmed that at the 100 kg P ha(-1) yr(-1) application rate, all sites exceeded the threshold for P saturation (30%). At depths greater than 30 cm, DPS was typically below the 30% saturation threshold. The DPS change points ranged from 25 to 34% for the 0- to 90-cm depths. Our research concluded that the risk of P leaching through the matrix of the Atlantic Coastal Plain soils studied was not high; however, P leaching via macropore bypass may contribute to P loss from these soils.     

Soil and surface runoff phosphorus relationships for five typical USA midwest soils

Excessively high soil P can increase P loss with surface runoff. This study used indoor rainfall simulations to characterize soil and runoff P relationships for five Midwest soils (Argiudoll, Calciaquaoll, Hapludalf, and two Hapludolls). Topsoil (15-cm depth, 241-289 g clay kg(-1) and pH 6.0-8.0) was incubated with five NH4H2PO4 rates (0-600 mg P kg(-1)) for 30 d. Total soil P (TPS) and soil-test P (STP) measured with Bray-P1 (BP), Mehlich-3 (M3P), Olsen (OP), Fe-oxide-impregnated paper (FeP), and water (WP) tests were 370 to 1360, 3 to 530, 10 to 675, 4 to 640, 7 to 507, and 2 to 568 mg P kg(-1), respectively. Degree of soil P saturation (DPS) was estimated by indices based on P sorption index (PSI) and STP (DPSSTP) and P, Fe, and Al extracted by ammonium oxalate (DPSox) or Mehlich-3 (DPSM3). Soil was packed to 1.1 g cm(-3) bulk density in triplicate boxes set at 4% slope. Surface runoff was collected during 75 min of 6.5 cm h(-1) rain. Runoff bioavailable P (BAP) and dissolved reactive P (DRP) increased linearly with increased P rate, STP, DPSox, and DPSM3 but curvilinearly with DPSSTP. Correlations between DRP or BAP and soil tests or saturation indices across soils were greatest (r > or = 0.95) for FeP, OP, and WP and poorest for BP and TPS (r = 0.83-0.88). Excluding the calcareous soil (Calciaquoll) significantly improved correlations only for BP. Differences in relationships between runoff P and the soil tests were small or nonexistent among the noncalcareous soils. Routine soil P tests can estimate relationships between runoff P concentration and P application or soil P, although estimates would be improved by separate calibrations for calcareous and noncalcareous soils.     

Environmental index for estimating the risk of phosphorus loss in calcareous soils of Manitoba

The degree of phosphorus saturation (DPS) has been used in evaluating the risk of P loss from soil to runoff. While techniques are available for calculating DPS for acid soils, no widely used technique exists for neutral to calcareous soils that are typical of the Northern Great Plains, including Manitoba (Canada) soils. This study aimed to develop techniques of calculating the DPS of neutral to alkaline soils. Four measures of soil labile P and ten indices of P sorption capacity were used to calculate the DPS of 115 Manitoba soils. The various DPS calculated were evaluated using water-extractable ((H2O)) P as an index of P susceptibility to runoff loss. The DPS obtained using Olsen-extractable ((Ols)) P and the Langmuir adsorption maximum (ES(max)) ranged from 0.5 to 31.9% while those obtained from P(Ols) and the single-point adsorption index (P(150)) ranged from 0.9 to 73.9%. Of all the DPS evaluated, those that included P(Ols) and Mehlich 3-extractable ((M3)) P as the numerator with either P(150) or ES(max) as the denominator were fairly well correlated with P(H2O) (r values ranged between 0.45 and 0.63). Along with ES(max) and P(150), a new method of calculating DPS was formulated as the ratio of P(Ols) or P(M3) to Ca(M3) or (Ca + Mg)(M3). We found that the ratio of ammonium oxalate-extractable ((ox)) P to (Al + Fe)(ox), which has been widely used to calculate DPS in acid soils, was not suitable for neutral to alkaline soils of Manitoba. In these neutral to alkaline soils, Ca(M3) or (Ca + Mg)(M3) were better indices of P sorption capacity while P(Ols) and P(M3) provided better estimates of labile soil P. The DPS calculated using Ca(M3) or (Ca + Mg)(M3) were well correlated with P(H2O); however, they were numerically smaller than those obtained from the Langmuir adsorption maximum. As such, a saturation coefficient (alpha) with a value of 0.2 was generated to improve the numerical values of the newly estimated DPS. This new approach can be used to estimate the DPS in neutral and calcareous soils without the need to generate a P adsorption maximum.     

Effect of mineral and manure phosphorus sources on runoff phosphorus

Concern over nonpoint-source phosphorus (P) losses from agricultural lands to surface waters has resulted in scrutiny of factors affecting P loss potential. A rainfall simulation study was conducted to quantify the effects of alternative P sources (dairy manure, poultry manure, swine slurry, and diammonium phosphate), application methods, and initial soil P concentrations on runoff P losses from three acidic soils (Buchanan-Hartleton, Hagerstown, and Lewbeach). Low P (12 to 26 mg kg(-1) Mehlich-3 P) and high P (396 to 415 mg kg(-1) Mehlich-3 P) members of each soil were amended with 100 kg total P ha(-1) from each of the four P sources either by surface application or mixing, and subjected to simulated rainfall (70 mm h(-1) to produce 30 min runoff). Phosphorus losses from fertilizer and manure applied to the soil surface differed significantly by source, with dissolved reactive phosphorus (DRP) accounting for 64% of total phosphorus (TP) (versus 9% for the unamended soils). For manure amended soils, these losses were linearly related to water-soluble P concentration of manure (r2 = 0.86 for DRP, r2 = 0.78 for TP). Mixing the P sources into the soil significantly decreased P losses relative to surface P application, such that DRP losses from amended, mixed soils were not significantly different from the unamended soil. Results of this study can be applied to site assessment indices to quantify the potential for P loss from recently manured soils.     

An alum-based water treatment residual can reduce extractable phosphorus concentrations in three phosphorus-enriched coastal plain soils

The accumulation of excess soil phosphorus (P) in watersheds under intensive animal production has been linked to increases in dissolved P concentrations in rivers and streams draining these watersheds. Reductions in water dissolved P concentrations through very strong P sorption reactions may be obtainable after land application of alum-based drinking water treatment residuals (WTRs). Our objectives were to (i) evaluate the ability of an alum-based WTR to reduce Mehlich-3 phosphorus (M3P) and water-soluble phosphorus (WSP) concentrations in three P-enriched Coastal Plain soils, (ii) estimate WTR application rates necessary to lower soil M3P levels to a target 150 mg kg(-1) soil M3P concentration threshold level, and (iii) determine the effects on soil pH and electrical conductivity (EC). Three soils containing elevated M3P (145-371 mg kg(-1)) and WSP (12.3-23.5 mg kg(-1)) concentrations were laboratory incubated with between 0 and 6% WTR (w w(-1)) for 84 d. Incorporation of WTR into the three soils caused a near linear and significant reduction in soil M3P and WSP concentrations. In two soils, 6% WTR application caused a soil M3P concentration decrease to below the soil P threshold level. An additional incubation on the third soil using higher WTR to soil treatments (10-15%) was required to reduce the mean soil M3P concentration to 178 mg kg(-1). After incubation, most treatments had less than a half pH unit decline and a slight increase in soil EC values suggesting a minimal impact on soil quality properties. The results showed that WTR incorporation into soils with high P concentrations caused larger relative reductions in extractable WSP than M3P concentrations. The larger relative reductions in the extractable WSP fraction suggest that WTR can be more effective at reducing potential runoff P losses than usage as an amendment to lower M3P concentrations.     

Relationship between soil test phosphorus and phosphorus in runoff: effects of soil series variability

Phosphorus loss in runoff from agricultural fields has been identified as an important contributor to eutrophication. The objective of this research was to determine the relationship between phosphorus (P) in runoff from a benchmark soil (Cecil sandy loam; fine, kaolinitic, thermic Typic Kanhapludult) and Mehlich III-, deionized water-, and Fe(2)O(3)-extractable soil P, and degree of phosphorus saturation (DPS). Additionally, the value of including other soil properties in P loss prediction equations was evaluated. Simulated rainfall was applied (75 mm h(-1)) to 54 1-m(2) plots installed on six fields with different soil test phosphorus (STP) levels. Runoff was collected in its entirety for 30 min and analyzed for total P and dissolved reactive phosphorus (DRP). Soil samples were collected from 0- to 2-, 0- to 5-, and 0- to 10-cm depths. The strongest correlation for total P and DRP occurred with DPS (r(2) = 0.72). Normalizing DRP by runoff depth resulted in improved correlation with deionized water-extractable P for the 0- to 10-cm sampling depth (r(2) = 0.81). The STP levels were not different among sampling depths and analysis of the regression equations revealed that soil sampling depth had no effect on the relationship between STP and P in runoff. For all forms of P in runoff and STP measures, the relationship between STP and runoff P was much stronger when the data were split into groups based on the ratio of oxalate-extractable Fe to Al. For all forms of P in runoff and all STP methods, R(2) increased with the inclusion of oxalate-extractable Al and Fe in the regression equation. The results of this study indicate that inclusion of site-specific information about soil Al and Fe content can improve the relationship between STP and runoff P.     

Phosphorus saturation in spodosols impacted by manure

Significant amounts of phosphorus (P) accumulate in soils receiving animal manures that could eventually result in unacceptable concentrations of dissolved P loss through surface runoff or subsurface leaching. The degree of phosphorus saturation (DPS) relates a soil's extractable P to its P sorbing capacity, and is reportedly a predictor of the P likely to be mobilized from a system. A DPS value (DPS-1) was derived that expressed the percentage of Mehlich 1-extractable P to the sorbing capacity of a Spodosol (expressed as the sum of oxalate-extractable Fe and Al). Values of DPS-1 were determined in various horizons of soil in current and abandoned dairy systems in South Florida's Lake Okeechobee watershed to assess P release potential. Land use within the dairies was classified as highly impacted by cattle (intensive and holding), and minimally impacted by cattle (pasture, forage, or native) areas. The A and E horizon of soils in heavily manure-impacted intensive and holding areas for both active and abandoned dairies generally had higher DPS-1 values than the pasture, forage, and native area soils, which were minimally impacted by manure. Degree of P saturation was also calculated as a percentage of Mehlich 1-extractable P to the sum of Mehlich 1-extractable Fe and Al (DPS-2). Both DPS-1 and DPS-2 were shown to be significantly (P = 0.0001) related to water-extractable P for all soil horizons, suggesting that either index can be used as an indicator for P loss potential from a soil.     

Soil mixing to decrease surface stratification of phosphorus in manured soils

Continual applications of fertilizer and manure to permanent grassland or no-till soils can lead to an accumulation of P at the surface, which in turn increases the potential for P loss in overland flow. To investigate the feasibility of redistributing surface stratified P within the soil profile by plowing, Mehlich-3 P rich surface soils (128-961 mg kg(-) in 0-5 cm) were incubated with lower-P subsoil (16-119 mg kg(-1) in 5-20 cm) for 18 manured soils from Oklahoma and Pennsylvania that had received long-term manure applications (60-150 kg P ha(-1) yr(-1) as dairy, poultry, or swine manure for up to 20 yr). After incubating a mixture of 5 g surface soil (0- to 5-cm depth) and 15 g subsoil (5- to 20-cm depth) for 28 d, Mehlich-3 P decreased 66 to 90% as a function of the weighted mean Mehlich-3 P of surface and subsoil (i.e.. 1:3 ratio) (r2 = 0.87). At Klingerstown, Northumberland County, south central Pennsylvania, a P-stratified Berks soil (Typic Dystrochrept) (495 mg kg(-1) Mehlich-3 P in 0- to 5-cm depth) was chisel plowed to about 25 cm and orchardgrass (Dactylis glomerata L.) planted. Once grass was established and erosion minimized (about 20 wk after plowing and planting), total P concentration in overland flow during a 30-min rainfall (6.5 cm h(-1)) was 1.79 mg L(-1) compared with 3.4 mg L(-1) before plowing, with dissolved P reduced from 2.9 to 0.3 mg L(-1). Plowing P-stratified soils has the potential to decrease P loss in overland flow, as long as plowing-induced erosion is minimized.     

Long-term phosphorus fertility in wastewater-irrigated cropland

Land treatment of municipal wastewater effluent is a proven method for augmenting freshwater resources and avoiding direct nutrient discharges to surface waters. We assessed changes in soil test phosphorus (P) of the Ap horizon of cropped fields continuously irrigated for 26 yr with secondary effluent from the Penn State University wastewater treatment plant. For annual P additions averaging 97 kg P ha(-1), Mehlich-3 P (M3P) response in the 0- to 20-cm surface soil (initially < 20 mg kg(-1)) was represented by two lines. For the first 12 yr of irrigation, soil test P increased, with 14.5 kg P ha(-1) needed to increase M3P by 1 mg P kg(-1). After the initial buildup, M3P maintained a quasi-steady-state value of approximately 110 mg kg(-1). Over time, the surface soil equilibrium P concentration at zero sorption increased markedly (from < 1 to 5.5 mg P L(-1)), and extractable aluminum (Al) decreased significantly (P < 0.001). Speciation modeling using Visual MINTEQ suggests complexation of Al by dissolved organic carbon at site pH conditions. Loss of Al from the surface layer lowered its P-sorbing capacity, causing added effluent-P to move into the subsoil. Results suggest that current management practices can continue for many years without exceeding the surface soil M3P environmental threshold (200 mg kg(-1)) used in state P-based nutrient policies.     

Approximating phosphorus release from soils to surface runoff and subsurface drainage

Phosphorus application in excess of crop needs has increased the concentration of P in surface soil and runoff and led many states to develop P-based nutrient management strategies. However, insufficient data are available relating P in surface soil, surface runoff, and subsurface drainage to develop sound guidelines. Thus, we investigated P release from the surface (0-5 cm depth) of a Denbigh silt loam from Devon, U.K. (30-160 mg kg-1 Olsen P) and Alvin, Berks, Calvin, and Watson soils from Pennsylvania (10-763 mg kg-1 Mehlich-3 P) in relation to the concentration of P in surface runoff and subsurface drainage. A change point, where the slopes of two linear relationships between water- or CaCl2-extractable soil P and soil test phosphorus (STP) (Olsen or Mehlich-3) meet, was evident for the Denbigh at 33 to 36 mg kg-1 Olsen P, and the Alvin and Berks soils at 185 to 190 mg Mehlich-3 P kg-1. Similar change points were also observed when STP was related to the P concentration of surface runoff (185 mg kg-1) and subsurface drainage (193 mg kg-1). The use of water and CaCl2 extraction of surface soil is suggested to estimate surface runoff P (r2 of 0.92 for UK and 0.86 for PA soils) and subsurface drainage P (r2 of 0.82 for UK and 0.88 for PA soils), and to determine a change point in STP, which may be used in support of agricultural and environmental P management.     

Soil variables for predicting potential phosphorus release in Swedish noncalcareous soils

The accumulation of P in agricultural soils due to fertilization has increased the risk of P losses from agricultural fields to surface waters. In risk assessment systems for P losses, both P release from soil to solution and transport mechanisms need to be considered. In this study, the overall objective was to identify soil variables for prediction of potential P release from soil to solution. Soils from nine sites of the Swedish long-term fertility experiment were used, each with four soil P levels. Phosphorus extractable with CaCl2 was used as an estimate of potential P release from soil to solution. Ammonium lactate-extractable phosphorus (P-AL) or NaHCO3-extractable phosphorus (Olsen P) could not be used alone for prediction of potential P release since soils with high phosphorus sorption capacity (PSC) released less P than soils with low PSC at the same soil test phosphorus (STP) level. Degree of phosphorus saturation (DPS) was calculated as Olsen P or P-AL as a percentage of PSC derived from P sorption isotherms or from Fe and Al extractable in ammonium oxalate. The CaCl2-extractable total phosphorus (CaCl2-TP) was exponentially related to these DPS values (r2 > or = 0.79). The CaCl2-TP was also linearly related to ratios between Olsen P or P-AL and a single-point phosphorus sorption index (PSI; r2 > or = 0.86). These ratios, which are easily determined and gave good correlations with CaCl2-TP, seemed to be the most useful estimates of potential P release for risk assessment systems.     

Use of drinking water treatment residuals as a potential best management practice to reduce phosphorus risk index scores

The P risk index system has been developed to identify agricultural fields vulnerable to P loss as a step toward protecting surface water. Because of their high Langmuir phosphorus adsorption maxima (P(max)), use of drinking water treatment residuals (WTRs) should be considered as a best management practice (BMP) to lower P risk index scores. This work discusses three WTR application methods that can be used to reduce P risk scores: (i) enhanced buffer strip, (ii) incorporation into a high soil test phosphorus (STP) soil, and (iii) co-blending with manure or biosolids. The relationship between WTR P(max) and reduction in P extractability and runoff P was investigated. In a simulated rainfall experiment, using a buffer strip enhanced with 20 Mg WTR ha(-1), runoff P was reduced by from 66.8 to 86.2% and reductions were related to the WTR P(max). When 25 g kg(-1) WTR was incorporated into a high STP soil of 315 mg kg(-1) determined using Mehlich-3 extraction, 0.01 M calcium chloride-extractable phosphorus (CaCl(2)-P) reductions ranged from 60.9 to 96.0% and were strongly (P < 0.01) related to WTR P(max). At a 100 g kg(-1) WTR addition, Mehlich 3-extractable P reductions ranged from 41.1 to 86.7% and were strongly (P < 0.01) related to WTR P(max). Co-blending WTR at 250 g kg(-1) to manure or biosolids reduced CaCl(2)-P by >75%. The WTR P(max) normalized across WTR application rates (P(max) x WTR application) was significantly related to reductions in CaCl(2)-P or STP. Using WTR as a P risk index modifying factor will promote effective use of WTR as a BMP to reduce P loss from agricultural land.     

Degree of phosphorus saturation thresholds in manure-amended soils of alberta

The risk of P losses from agricultural land to surface and ground water generally increases as the degree of soil P saturation increases. A single-point soil P sorption index (PSI) was validated with adsorption isotherm data for determination of the P sorption status of Alberta soils. Soil P thresholds (change points) were then examined for two agricultural soils after eight annual applications of different rates of cattle manure and for three agricultural soils after one application of different rates of cattle manure. Linear relationships were found between soil-test P (STP) levels up to 1000 mg kg(-1) and desorbed P in the five Alberta soils. Weak linear relationships were also found between STP and runoff dissolved reactive phosphorus (DRP) in three of these soils. Change points for the degree of P saturation (DPS) were detected in four of the five soils at 3 to 44% for water-extractable P (WEP) and at 11 to 51% for CaCl(2)-extractable P (CaCl(2)-P). Change points were not found for DPS or runoff DRP. Overall DPS thresholds for the five soils combined were 27% for WEP and 44% for CaCl(2)-P at a critical desorbable-P value of 1 mg L(-1). The corresponding STP levels (44 mg kg(-1) for WEP and 71 mg kg(-1) for CaCl(2)-P) are similar to agronomic thresholds for crops grown on Alberta soils. Soluble P losses in overland flow and leaching may be greater in soils with DPS values that exceed these thresholds than in soils with lower DPS values.     

Accelerated deployment of an agricultural nutrient management tool: the Maryland Phosphorus Site Index

In 1998, the Maryland legislature mandated nitrogen (N) and phosphorus (P) nutrient management planning for nearly all of Maryland's commercial agricultural operations. State regulations required that a phosphorus indexing tool (P Index) be used for determining the potential for P losses from agricultural land, even though a reliable P Index did not exist. The development and assessment of the P Index as a dependable tool for the evaluation of the potential for P losses was constrained by a very aggressive implementation schedule imposed by state regulations. The Maryland Phosphorus Site Index (PSI) was evaluated on 646 state-representative field sites beginning in the spring of 1999 and continuing through the spring of 2000. Of the representative fields, 69% were determined to have a "low" P loss rating, 19% were in the "medium" P loss rating category, 8% were determined to be a "high" risk for P loss, and 4% rated as "very high" P loss potential. Fifty-five percent of the fields evaluated had soil test phosphorus (STP) levels less than the 75 mg kg-1 Mehlich-1 P environmental threshold established by state regulations. The frequency distribution of PSI performance was evaluated for several subcategories of the statewide data set. The Maryland PSI will be deployed for use in constructing farm nutrient management plans well before its predictive capabilities can be objectively and rigorously validated. Field validation is essential. In the meantime, the Maryland PSI should function adequately as a tool to assist in the prioritization of field P loss risk potential.     

Spatial analysis of phosphorus sorption capacity in a semiarid altered wetland

The observed increase in phosphorus (P) loading into the Jordan River could increase eutrophication processes in Lake Kinneret, the only freshwater lake in Israel, which provides 25% of the country's drinking water. The P may originate from the peat soils of the highly altered Hula Valley's semiarid wetland ecosystem through which the Jordan River runs. The objectives of this research were to ascertain the sorption capacity of these soils and to identify areas with high potential for P release from soils to ground water. We extracted 80 soil samples collected across the valley with ammonium oxalate and determined the ratio of extractable P to Fe and Al, from which we derived the degree of phosphorus saturation (DPS). A relatively low DPS (<15%) was observed in Histosols compared with the high DPS (>30%) observed in many of the hydromorphic organo-mineral soils. We used a sequential Gaussian simulation technique to assess the spatial pattern of the DPS and found that the Histosols have a low probability (<10%) of exceeding the widely used environmental DPS threshold of 25%. The areas characterized by mineral soils, such as hydromorphic Vertisols and various marl redoximorphic soils, have a high probability (>60%) of exceeding the threshold value. The ability to predict the concentrations of dissolved P in ground water based on DPS values was somewhat impaired because of the preferential flow characteristics in this altered wetland.     

Evaluation of phosphorus transport in surface runoff from packed soil boxes

Evaluation of phosphorus (P) management strategies to protect water quality has largely relied on research using simulated rainfall to generate runoff from either field plots or shallow boxes packed with soil. Runoff from unmanured, grassed field plots (1 m wide x 2 m long, 3-8% slope) and bare soil boxes (0.2 m wide and 1 m long, 3% slope) was compared using rainfall simulation (75 mm h(-1)) standardized by 30-min runoff duration (rainfall averaged 55 mm for field plots and 41 mm for packed boxes). Packed boxes had lower infiltration (1.2 cm) and greater runoff (2.9 cm) and erosion (542 kg ha(-1)) than field plots (3.7 cm infiltration; 1.8 cm runoff; 149 kg ha(-1) erosion), yielding greater total phosphorus (TP) losses in runoff. Despite these differences, regressions of dissolved reactive phosphorus (DRP) in runoff and Mehlich-3 soil P were consistent between field plots and packed boxes reflecting similar buffering by soils and sediments. A second experiment compared manured boxes of 5- and 25-cm depths to determine if variable hydrology based on box depth influenced P transport. Runoff properties did not differ significantly between box depths before or after broadcasting dairy, poultry, or swine manure (100 kg TP ha(-1)). Water-extractable phosphorus (WEP) from manures dominated runoff P, and translocation of manure P into soil was consistent between box types. This study reveals the practical, but limited, comparability of field plot and soil box data, highlighting soil and sediment buffering in unamended soils and manure WEP in amended soils as dominant controls of DRP transport.