Effect of biochars on adsorption of Cu(II), Pb(II) and Cd(II) by three variable charge soils from southern China

The purpose of this study is to compare the relative contribution of different mechanisms to the enhanced adsorption of Cu(II), Pb(II) and Cd(II) by variable charge soils due to incorporation of biochars derived from crop straws. The biochars were prepared from the straws of canola and peanut using an oxygen-limited pyrolysis method at 350 °C. The effect of biochars on adsorption and desorption of Cu(II), Pb(II) and Cd(II) by and from three variable charge soils from southern China was investigated with batch experiments. Based on the desorption of pre-adsorbed heavy metals, the electrostatic and non-electrostatic adsorptions were separated. EDTA was used to replace the heavy metals complexed with biochars and to evaluate the complexing ability of the biochars with the metals. The incorporation of biochars increased the adsorption of Cu(II), Pb(II) and Cd(II) by the soil; peanut straw char induced a greater increase in the adsorption of the three metals. The increased percentage of Cd(II) adsorption induced by biochars was much greater than that for the adsorption of Cu(II) and Pb(II). Cu(II) adsorption on three variable charge soils was enhanced by the two biochars mainly through a non-electrostatic mechanism, while both electrostatic and non-electrostatic mechanisms contributed to the enhanced adsorption of Pb(II) and Cd(II) due to the biochars. Peanut straw char had a greater specific adsorption capacity than canola straw char and thus induced more non-electrostatic adsorption of Cu(II), Pb(II) and Cd(II) by the soils than did the canola straw char. The complexing ability of the biochars with Cu(II) and Pb(II) was much stronger than that with Cd(II) and thus induced more specific adsorption of Cu(II) and Pb(II) by the soils than that of Cd(II). Biochars increased heavy metal adsorption by the variable charge soils through electrostatic and non-electrostatic mechanisms, and the relative contribution of the two mechanisms varied with metals and biochars.     

The mechanism of chromate sorption by three variable charge soils

Adsorption of chromate and desorption of the pre-adsorbed chromate were studied using three representative variable charge soils from the south of China. The mechanisms of the adsorption were discussed based on the hydroxyl release and the change of zeta potential during the chromate adsorption. The adsorption and desorption of chromate followed the same order: the Hyper-Rhodic Ferralsol>the Rhodic Ferralsol>the Haplic Acrisol. The adsorption and the desorption both increased with elevation of the equilibrium chromate concentration and decreased with increasing of the soil solution pH. The percentage of the specific adsorption of chromate was 54.0-59.4%, 54.3-60.3%, and 43.9-46.2% for the Hyper-Rhodic Ferralsol, the Rhodic Ferralsol, and the Haplic Acrisol, respectively; the percentage of the electrostatic adsorption was 40.0-46.6%, 39.7-45.8%, and 50.8-56.5% for the three soils, respectively. These findings suggest that both the specific adsorption and the electrostatic adsorption contributed to the chromate adsorption by the variable charge soils. The hydroxyl release during the chromate adsorption shared the same trend with the adsorption envelopes, and decreased with increasing of pH. This is attributed to the exchange of chromate with the hydroxyl on the soil particle surfaces and the formation of a chemical bond between chromate and the surface. Our results indicate that the adsorption of chromate resulted in a shift of zeta potential-pH curves of the soil colloids to negative values, which suggests that the adsorption increased the negative surface charge and decreased the surface potential of the soil colloids.     

Adsorption of arsenate on soils. Part 2: modeling the relationship between adsorption capacity and soil physiochemical properties using 16 Chinese soils

An attempt has been made to elucidate the effects of soil properties on arsenate adsorption by modeling the relationships between adsorption capacity and the properties of 16 Chinese soils. The model produced was validated against three Australian and three American soils. The results showed that nearly 93.8% of the variability in arsenate adsorption on the low-energy surface could be described by citrate-dithionite extractable Fe (Fe(CD)), clay content, organic matter content (OM) and dissolved organic carbon (DOC); nearly 87.6% of the variability in arsenate adsorption on the high-energy surface could be described by Fe(CD), DOC and total arsenic in soils. Fe(CD) exhibited the most important positive influence on arsenate adsorption. Oxalate extractable Al (Al(OX)), citrate-dithionite extractable Al (Al(CD)), extractable P and soil pH appeared relatively unimportant for adsorption of arsenate by soils.     

Desorption of cadmium from goethite: effects of pH, temperature and aging

Cadmium is perhaps environmentally the most significant heavy metal in soils. Bioavailability, remobilization and fate of Cd entering in soils are usually controlled by adsorption-desorption reactions on Fe oxides. Adsorption of Cd on soil colloids including Fe oxides has been extensively studied but Cd desorption from such soil minerals has received relatively little attention. Some factors that affect Cd adsorption on goethite include pH, temperature, aging, type of index cations, Cd concentrations, solution ionic strength and presence of organic and inorganic ions. This research was conducted to study the influence of pH, temperature and aging on Cd desorption from goethite. Batch experiments were conducted to evaluate Cd desorption from goethite with 0.01 M Ca(NO3)2. In these experiments Cd desorption was observed at 20, 40 and 70 degrees C in combination with aging for 16 h, 30, 90 and 180 d from goethite that adsorbed Cd from solutions containing initial Cd concentrations of 20, 80 and 180 microM. Following the adsorption step Cd desorption was measured by 15 successive desorptions after aging at various temperatures. At the lowest amount of initially adsorbed Cd and equilibrium pH 5.5, cumulative Cd desorption decreased from 71% to 17% with aging from 16 h to 180 d and the corresponding decrease at equilibrium pH 6.0 was from 32% to 3%. There was a substantial decrease in Cd desorption with increasing equilibration temperature. For example, in goethite with the lowest amount of initial adsorption at equilibrium pH 5.5, cumulative Cd desorption decreased from 71% to 31% with increase in temperature from 20 to 70 degrees C, even after 16 h. Dissolution of Cd adsorbed goethite in 1M HCl, after 15 successive desorptions with 0.01 M Ca(NO3)2, indicated that approximately 60% of the Cd was surface adsorbed. Overall, dissolution kinetics data revealed that 23% to 88% Cd could not be desorbed, which could possibly be diffused into the cracks and got entrapped in goethite crystals. At elevated temperature increased equilibrium solution pH favoured the formation of CaCO3 and CdCO3 which reasonably decreased Cd desorption. Cadmium speciation showed the formation of calcite and otavite minerals at 40 and 70 degrees C due to increase in pH (>9.5) during aging. X-ray diffraction analysis (XRD) of these samples also revealed the formation of CaCO3 at elevated temperatures with aging. While mechanisms such as Cd diffusion and/or entrapment into fissures and cracks in goethite structure with increase in temperature and aging are possible.     

Effect of biosolid incorporation on arsenic distribution in Mollisol soils in central Chile

The effect of biosolid incorporation on arsenic distribution in Mollisol soils in central Chile was studied. Two soils were sequentially extracted for arsenic with a five-step method that accounts for the following arsenic forms: non-specifically adsorbed (F1), specifically adsorbed (F2), amorphous and poorly crystallized Fe and Al oxides (F3), well-crystallized Fe and Al oxides (F4) and residual (F5). The arsenic residual fraction was predominant in Pintué soil, whereas in Graneros soil, arsenic was mostly associated to amorphous Fe and Al oxides. Graneros soil exhibited a higher As(V) adsorbing capacity than Pintué soil, which relates to the higher clay and iron and aluminum oxides contents, confirming that these components participation is essential for the adsorption of this metalloid. Biosolid application at a rate of 100Mg ha(-1) caused an increase in arsenic bound to amorphous Fe and Al oxides and in the residual fraction, in Pintué soil. When Pintué soil was spiked with arsenic, aged for two months, and treated with biosolid (100Mg ha(-1)), the content of arsenic in the most labile fractions decreased, thus showing a favorable effect in its application to soils with few specific sites for arsenic adsorption. Arsenic speciation was carried out in the first two fractions of the sequential extraction procedure. As(V) was the main form in both fractions. Biosolid incorporation at a rate of 100Mg ha(-1) caused a significant increase in organic arsenic forms.     

Appendix

Abstract

The interaction of glyphosate [N‐(phosphonomethyl)‐glycine] with four typical European soils is reported. Results of adsorption and desorption isotherms show that the interaction of glyphosate with these soils was mainly related to content of iron and aluminium amorphus hydroxides. Moreover, it was found that the presence of divalent cations in 2: 1 clay minerals also contribute to glyphosate adsorption. The S‐type form of the adsorption isotherms revealed the existence of two different binding sites. These were exchangeable cations at low herbicide concentration and Fe and Al at higher glyphosate concentrations. The K maximum values of adsorption provided by the linear form of the Langmuir equation were found to be more consistent with soil parameters than those calculated by the Freundlich equation. The order of desorption from the soils was the reverse of that found for adsorption. Moreover, desorption varied from around 15 to 80% of the adsorbed herbicide according to the soil characteristics. This indicated that glyphosate adsorption on soils is far from being permanent and leaching to lower soil horizons with limited biological activity may occur.     

Adsorption and desorption of cadmium by goethite pretreated with phosphate

The adsorption of Cd by oxides or soils have been extensively studied, however, the desorption has received relatively limited attention, especially in the presence of phosphate. In this study, a batch equilibration method was used to investigate Cd sorption and desorption by goethite pretreated with phosphate. Phosphate not only enhanced Cd adsorption, but also accelerated the adsorption process. Compared with Cd adsorption by goethite alone, phosphate substantially moved the adsorption curves (edges) to lower pH range, indicative of enhancement of Cd sorption. The Cd adsorption by the pretreated goethite reached apparent equilibrium within 24 h at 20 degrees C, while such equilibrium was not observed after 4 weeks in the absence of phosphate. Cadmium was more readily released from phosphate-treated goethite. It is believed that phosphate blocked the pores on goethite surface, which lead to the fast adsorption kinetics and high extraction percentage. These results provided strong support for the diffusion of Cd into goethite particles.     

Adsorption and cosorption of cadmium and glyphosate on two soils with different characteristics

Glyphosate [N-(phosphonomethyl)glycine] (GPS; H3G) is a widely used pesticide throughout the world. It affects metal behaviors in soil-plant system due to its functional groups, which react with metal ions to form metal complexes. Adsorption and cosorption of cadmium and glyphosate on a Wushan soil (WS soil, Anthrosol) and a Zhuanhong soil (ZH soil, Udic Ferrisol) as affect by solution pH were studied by means of batch adsorption experiments. It indicated that the adsorption quantity of Cd or glyphosate was highly relevant to soil characteristics. The WS soil had higher adsorption capacity of Cd than the ZH soil, due to its high organic matter content and cation exchange capacity (CEC). In contrast, the adsorption quantity of glyphosate on the WS soil was less than that on the ZH soil, because the WS soil has lower iron and aluminum oxides content but higher pH than the ZH soil. The herbicide glyphosate affected Cd adsorption on the two soils when they coexisted in a same soil solution, which was attributed to a glyphosate-induced pH-decrease and the corresponding decline in negative surface charges of the soil. Beside that, glyphosate reacted with solution Cd to form the water-soluble complexes that had lower affinity to soil surface in comparison with Cd itself. On the other hand, the presence of Cd in the soil solution also affected the adsorption of glyphosate on the soils. The presence of Cd increased adsorption quantity of glyphosate on the WS and ZH soils, which was resulted from the decrease of equilibrium solution pH caused by Cd2+ exchange with H+ ions of soil surface. In addition to that, glyphosate adsorption possibly takes place on sites where Cd was previously adsorbed and acted as a bridge between the soil and glyphosate.     

Evaluation of an approach for the characterization of reactive and available pools of 20 potentially toxic elements in soils: part II--solid-solution partition relationships and ion activity in soil solutions

To assess environmental risks related to contaminants in soil it is essential to predict the available pool of inorganic contaminants at regional scales, accounting for differences between soils from variable geologic and climatic origins. An approach composed of a well-accepted soil extraction procedure (0.01 M CaCl(2)) and empirical Freundlich-type models in combination with mechanistically based models which to date have been used only in temperate regions was applied to 136 soils from a South European area and evaluated for its possible general use in risk assessment. Empirical models based on reactive element pools and soil properties (pH, organic carbon, clay, total Al, Fe and Mn) provided good estimations of available concentrations for a broad range of contaminants including As, Ba, Cd, Co, Cu, Hg, Mo, Ni, Pb, Sb, Se and Zn (r(2): 0.46-0.89). The variation of the pools of total Al in soils expressed the sorptive capacity of aluminosilicates and Al oxides at the surfaces and edges of clay minerals better than the actual variability of clay contents. The approach has led to recommendations for further research with particular emphasis on the impact of clay on the solubility of As and Sb, on the mechanisms controlling Cr and U availability and on differences in binding properties of soil organic matter from different climatic regions. This study showed that such approach may be included with a good degree of certainty for first step risk assessment procedures to identify potential risk areas for leaching and uptake of inorganic contaminants in different environmental settings.     

Influence of solution acidity and CaCl2 concentration on the removal of heavy metals from metal-contaminated rice soils

Soil washing is considered a useful technique for remediating metal-contaminated soils. This study examined the release edges of Cd, Zn, Ni, Cr, Cu or Pb in two contaminated rice soils from central Taiwan. The concentrations exceeding the trigger levels established by the regulatory agency of Taiwan were Cu, Zn, Ni and Cr for the Ho-Mei soil and Pb for the Nan-Tou soil. Successive extractions with HCl ranging from 0 to 0.2 M showed increased release of the heavy metals with declining pH, and the threshold pH value below which a sharp increase in the releases of the heavy metals was highest for Cd, Zn, and Ni (pH 4.6 to 4.9), intermediate for Pb and Cu (3.1 to 3.8) and lowest for Fe (2.1), Al (2.2) and Cr (1.7) for the soils. The low response slope of Ni and Cr particularly for the rice soils make soil washing with the acid up to the highest concentration used ineffective to reduce their concentrations to below trigger levels. Although soil washing with 0.1 M HCl was moderately effective in reducing Cu, Pb, Zn and Cd, which brought pH of the soils to 1.1+/-0.1 (S.D.), the concurrent release of large quantities of Fe and Al make this remediation technique undesirable for the rice soils containing high clay. Successive washings with 0.01 M HCl could be considered an alternative as the dissolution of Fe and Al was minimal, and between 46 to 64% of Cd, Zn, and Cu for the Ho-Mei soil and 45% of Pb in the Na-Tou soil were extracted after four successive extractions with this dilute acid solution. The efficacy of Cd extraction improved if CaCl2 was added to the acid solution. The correlation analysis revealed that Cr extracted was highly correlated (P < 0.001) with Fe extracted, whereas the Cu, Ni, Zn, Cd or Pb extracted was better correlated (P < 0.001) with Al than with Fe extracted. It is possible that the past seasonal soil flooding and drainage in the soils for rice production was conducive to incorporating Cr within the structure of Fe oxide, thereby making them extremely insoluble even in 0.2 M HCl solution. The formation of solid solution of Ni with Al oxide was also possible, making it far less extractable than Cd, Zn, Cu, or Pb with the acid concentrations used.     

Arsenic immobilization in soils amended with drinking-water treatment residuals

Use of Fe/Al hydroxide-containing materials to remediate As-contaminated sites is based on the general notion that As adsorption in soils is primarily controlled by Fe/Al (hydr)oxides. A low-cost and potentially effective substitute for natural Fe/Al hydroxides could be the drinking-water treatment residuals (WTRs). Earlier work in our laboratory has shown that WTRs are effective sorbents for As in water. We hypothesized that land-applied WTRs would work equally well for As-contaminated soils. Results showed that WTRs significantly (p<0.001) increased the soil As sorption capacity. All WTR loads (2.5, 5, and 10%) significantly (p<0.001) increased the overall amount of As sorbed by both soils when compared with that of the unamended controls. The amount of As desorbed with phosphate (7500 mg kg(-1) load) was approximately 50%. The WTR effectiveness in increasing soil As sorption capacities was unaffected by differences in both soils' chemical properties.     

Streaming potential method for characterizing interaction of electrical double layers between rice roots and Fe/Al oxide-coated quartz in situ

The interaction between rice roots and Fe/Al oxide-coated quartz was investigated through zeta potential measurements and column leaching experiments in present study. The zeta potentials of rice roots, Fe/Al oxide-coated quartz, and the binary systems containing rice roots and Fe/Al oxide-coated quartz were measured by a specially constructed streaming potential apparatus. The interactions between rice roots and Fe/Al oxide-coated quartz particles were evaluated/deduced based on the differences of zeta potentials between the binary systems and the single system of rice roots. The zeta potentials of the binary systems moved in positive directions compared with that of rice roots, suggesting that there were overlapping of diffuse layers of electric double layers on positively charged Fe/Al oxide-coated quartz and negatively charged rice roots and neutralization of positive charge on Fe/Al oxide-coated quartz with negative charge on rice roots. The greater amount of positive charges on Al oxide led to the stronger interaction of Al oxide-coated quartz with rice roots and the more shift of zeta potential compared with Fe oxide. The overlapping of diffuse layers on Fe/Al oxide-coated quartz and rice roots was confirmed by column leaching experiments. The greater overlapping of diffuse layers on Al oxide and rice roots led to more simultaneous adsorptions of K⁺ and NO₃ ^? and greater reduction in leachate electric conductivity when the column containing Al oxide-coated quartz and rice roots was leached with KNO₃ solution, compared with the columns containing rice roots and Fe oxide-coated quartz or quartz. When the KNO₃ solution was replaced with deionized water to flush the columns, more K⁺ and NO₃ ^? were desorbed from the binary system containing Al oxide-coated quartz and rice roots than from other two binary systems, suggesting that the stronger electrostatic interaction between Al oxide and rice roots promoted the desorption of K⁺ and NO₃ ^? from the binary system and enhanced overlapping of diffuse layers on these oppositely charged surfaces compared with other two binary systems. In conclusion, the overlapping of diffuse layers occurred between positively charged Fe/Al oxides and rice roots, which led to neutralization of opposite charge and affected adsorption and desorption of ions onto and from the charged surfaces of Fe/Al oxides and rice roots.     

Effect of organic acids on adsorption and desorption of rare earth elements

Effect of citric, malic, tartaric and acetic acids on adsorption of La, Ce, Pr and Nd by and desorption from four typical Chinese soils was studied. Generally, adsorption capacities of rare earth elements (REEs) were significantly correlated with the cation exchange capacity (CEC) of soils. In the presence of acetic acids adsorption of REEs was similar to that in the presence of Ca(NO3)2. However, in the presence of citric, malic and tartaric acids adsorption of REEs by Heilongjiang, Zhejiang and Guangdong soils decreased to varying extents if compared with that in the presence of nitrate and acetic acid. The significance of suppression followed the order of citric acid > malic acid > tartaric acid > acetic acid, which was consistent with the order of stability of complexes of REEs with these organic acids. However, the adsorption increased with increasing equilibrium solution pH. For Jiangxi soil with low soil pH, CEC and organic matter these organic acids exerted an even more serious suppression effect on the adsorption of REEs. Another feature of the relationship between the adsorption of REEs and equilibrium solution pH was that the adsorption of REEs decreased with increase of pH from 2 to 4.5 and then slightly increased with further increase of pH. Desorption of REEs varied with soils and with organic acids as well. REEs were released easily from Heilongjiang, Zhejiang and Guangdong soils in the presence of organic acid. Generally, desorption of REEs decreased with increasing equilibrium solution pH. Effect of organic acids on desorption of REEs from Jiangxi soil was more complicated. In the presence of citric and malic acids no decrement and/or slight increase in desorption of REEs were observed over the equilibrium solution pH from 3 to 6.5. The reasons for this were ascribed to the strong complexing capacity of citric and malic acids and low soil pH, CEC and organic matter of Jiangxi soil.     

Adsorption and transport of arsenate in carbonate-rich soils: coupled effects of nonlinear and rate-limited sorption

The transport and fate of arsenate in carbonate-rich soil under alkaline conditions was investigated with multiple approaches combining batch, sequential extraction and column experiments as well as transport modeling studies. Batch experiments indicated that sorption isotherm was nonlinear over a wide range of concentration (0.1-200 mg L(-1)) examined. As(V) adsorption to the calcareous soil was initially fast but then continued at a slower rate, indicating the potential effect of rate-limited sorption on transport. Column experiments illustrated that transport of As(V) was significantly retarded compared to a non-reactive tracer. The degree of retardation decreased with increasing As(V) concentration. As(V) breakthrough curves exhibited nonideal transport behavior due to the coupled effects of nonlinear and rate-limited sorption on arsenate transport, which is consistent with the results of modeling studies. The contribution of nonlinear sorption to the arsenate retardation was negligible at low concentration but increased with increasing As(V) concentration. Sequential extraction results showed that nonspecifically sorbed (easily exchangeable, outer sphere complexes) fraction of arsenate is dominant with respect to the inner-sphere surface bound complexes of arsenate in the carbonate soil fraction, indicating high bioavailability and transport for arsenate in the carbonate-rich soils of which Fe and Al oxyhydroxide fractions are limited.     

Fluoride removal performance of a novel Fe-Al-Ce trimetal oxide adsorbent

A trimetal oxide was developed as a fluoride adsorbent by coprecipitation of Fe(II), Al(III) and Ce(IV) salt solutions with a molar ratio of 1:4:1 under alkaline condition. The material retained amorphous structure and maintained relatively stable fluoride adsorption performance at calcination temperatures lower than 600 degrees C. The optimum pH range for fluoride adsorption was 6.0-6.5 and the adsorbent also showed high defluoridation ability around pH 5.5-7.0, which is preferable for actual application. A high fluoride adsorption capacity of 178 mg g(-1) was acquired under an equilibrium fluoride concentration of 84.5 mg l(-1), adsorbent dose of 150 mg l(-1) and pH 7.0. The adsorption isotherm could be better described by the two-site Langmuir model than the one-site model, suggesting the existence of two types of active sites on the adsorbent surface. Coexistence of high concentrations of phosphate or arsenate only led to partial inhibition of fluoride adsorption, which further suggests the existence of heterogeneous adsorption sites. Sulfate and chloride did not affect fluoride adsorption, and nitrate influenced it only when the concentration of NO(3)(-)-N exceeded 50 mg l(-1). A high desorption efficiency of 97% was achieved by treating fluoride loaded Fe-Al-Ce oxide with NaOH solution at pH 12.2. A column experiment using the adsorbent fabricated into 1mm pellets was performed at an initial fluoride concentration of 5.5 mg l(-1), space velocity of 5h(-1) and pH of 5.8, and 2240 bed volumes were treated with the effluent fluoride under 1.0 mg l(-1).     

Mutual effects of cadmium and phosphate on their adsorption and desorption by goethite

Adsorption of cadmium (Cd) and phosphate by oxides or soils has been extensively studied, but the adsorption/desorption kinetics and mutual effects of these two species in co-existing systems has received little attention. In this study, a batch equilibration method was used to investigate the effect of phosphate and its application time on Cd adsorption and desorption on goethite. The influence of Cd and its application time on phosphate sorption and desorption kinetics was also determined. For Cd adsorption, phosphate was introduced into the system by two sequences: pre-treating goethite at 40 (degrees)C for 1 week, and applying with Cd simultaneously. Similarly, for phosphate sorption, Cd was applied by pre-treating goethite at 40 (degrees)C for 1 week or simultaneous addition with phosphate. Results demonstrated that phosphate added to goethite enhanced Cd adsorption, and facilitated Cd release as compared to untreated goethite. Cadmium had slightly higher adsorption, but a significantly faster desorption rate from the goethite simultaneously treated with phosphate and Cd, as compared to phosphate-pretreated goethite. Cadmium and its application time had little impact on phosphate sorption by goethite. However, phosphate desorption kinetics was affected by Cd application time. When the sorption time was short (15 min), phosphate desorption was faster from the goethite that was simultaneously treated with phosphate and Cd, as compared to Cd pretreated or untreated goethite. In contrast, a longer sorption time (4 weeks) resulted in a higher desorption rate of phosphate from Cd pretreated goethite than simultaneously phosphate-Cd treated goethite. This study provided useful information on adsorption/desorption kinetics in complicated Cd-phosphate-goethite systems.     

土壤颗粒级配对镉吸附-解吸规律的影响

利用甘肃金川某地土壤通过批实验进行等温吸附和动力学解吸实验,研究不同颗粒级配的中砂对镉的吸附、解吸特征,并采用Freundlich和一级动力学方程对其吸附解吸方程进行拟合。结果表明,(1)Freundlich和一级动力学方程对该土壤吸附、解吸镉的实验适用;(2)等温吸附实验中4组不同颗粒级配的中砂对镉的吸附性很强,最大平衡吸附量依次为260.667、286.107、299.362和292.232 mg/kg,吸附性能与颗粒级配中的细粒土相对含量大小成正比;(3)4组土壤对镉的解吸在初期2 h内解吸速率均较快,在3 h左右达到吸附-解吸平衡。平衡后4组土样Ⅰ、Ⅱ、Ⅲ和Ⅳ的最大解吸量依次为0.752、0.561、0.44和0.54 mg/kg,解吸速率和平衡时最大解吸量均与颗粒级配中细颗粒相对含量密切相关。     

Adsorption of Pb(II) on variable charge soils amended with rice-straw derived biochar

Two Ultisols and one Oxisol from tropical regions of southern China were incubated with rice straw biochar to investigate the effect of biochar on their surface charge and Pb(II) adsorption using batch methods. The incorporation of biochar induced a remarkable increase in soil cation exchange capacity after 30 d of incubation. The incorporation of biochar significantly increased the adsorption of Pb(II) by these variable charge soils; the enhancement of adsorption of Pb(II) by these soils increased with the addition level of biochar. Adsorption of Pb(II) involved both electrostatic and non-electrostatic mechanisms; however, biochar mainly increased Pb(II) adsorption through the non-electrostatic mechanism via the formation of surface complexes between Pb²⁺ and functional groups on biochar. There was greater enhancement of biochar on the non-electrostatic adsorption of Pb(II) by the variable charge soils at relatively low pH. Therefore, the incorporation of biochar decreased the activity and availability of Pb(II) to plants through increased non-electrostatic adsorption of Pb(II) by acidic variable charge soils.     

Cadmium adsorption and desorption behaviour on goethite at low equilibrium concentrations: effects of pH and index cations

The transport and bioavailability of cadmium is governed mainly by its adsorption-desorption reactions with minerals such as goethite--a common iron oxide mineral in variable charged and highly weathered tropical soils. Soil factors such as pH, temperature, solution Cd concentration, ionic strength and ageing affect Cd adsorption on goethite. The desorption behaviour of Cd from goethite at low concentrations is not fully understood. This study investigates the adsorption-desorption of Cd at low Cd concentrations (Cd adsorbed on goethite from 20 to 300 microM Cd solutions) in Na and Ca nitrate solutions of 0.03 M nominal ionic strengths. Synthetic goethite prepared by ageing a ferric hydroxide gel at high pH and room temperature was used for Cd adsorption and desorption studies. For desorption experiment 10 successive desorptions were made for the whole range of initial Cd concentrations (20-300 microM) in the presence of 0.01 M Ca(NO3)2 or 0.03 M NaNO3 solutions. Cadmium adsorption was found to be higher in Na+ than Ca2+ probably due to the competition of Ca2+ ions with Cd2+ ions for adsorption sites on the surfaces of goethite. The effect of index cation on Cd adsorption diminished with increase in pH from 5.0 to 6.0. Cadmium desorption decreased with increase in pH from 5.0 to 6.0 in both Na and Ca systems. After 10 successive desorptions with 0.03 M NaNO3 at the lowest initially adsorbed Cd approximately 45%, 20% and 7% of the adsorbed Cd was desorbed at pH 5.0, 5.5 and 6.0, respectively. The corresponding desorptions in the presence of 0.01 M Ca(NO3)2 were 49%, 22% and 8%, respectively. The Freundlich parameter, k, based on each progressive step of desorption at different adsorbed concentration increased with increasing desorption step, which may indicates that a fraction of Cd was resistant to desorption. Low Cd desorbability from goethite may be due to its specific adsorption and/or possibly as a result of Cd entrapment in the cracks or defects in goethite structure.     

Transfer functions for solid-solution partitioning of cadmium for Australian soils

To assess transport and ecotoxicological risks of metals, such as cadmium (Cd) in soils, models are needed for partitioning and speciation. We derived regression-based “partition-relations” based on adsorption and desorption experiments for main Australian soil types. First, batch adsorption experiments were carried out over a realistic range of dissolved Cd concentrations in agricultural soils in Australia. Results showed linear sorption relationships, implying the adequacy of using Kd values to describe partitioning. Desorption measurements were then carried out to assess in-situ Kd values and relate these to soil properties The best transfer functions for solid-solution partitioning were found for Kd values relating total dissolved Cd concentration to total soil Cd concentrations, accounting for the variation in pH, SOM contents and DOC concentrations. Model predictions compared well with measurements of an independent data set, but there was a tendency to underestimate dissolved Cd concentrations of highly polluted soils.