Adsorption Characteristics of Benzene on Biosolid Adsorbent and Commercial Activated Carbons

Abstract

This study selected biosolids from a petrochemical waste-water treatment plant as the raw material. The sludge was immersed in 0.5-5 M of zinc chloride (ZnCl₂) solutions and pyrolyzed at different temperatures and times. Results indicated that the 1-M ZnCl₂-immersed biosolids pyrolyzed at 500 °C for 30 min could be reused and were optimal biosolid adsorbents for benzene adsorption. Pore volume distribution analysis indicated that the mesopore contributed more than the macropore and micropore in the biosolid adsorbent. The benzene adsorption capacity of the biosolid adsorbent was 65 and 55% of the G206 (granular-activated carbon) and BPL (coal-based activated carbon; Calgon, Carbon Corp.) activated carbons, respectively. Data from the adsorption and desorption cycles indicated that the benzene adsorption capacity of the biosolid adsorbent was insignificantly reduced compared with the first-run capacity of the adsorbent; therefore, the biosolid adsorbent could be reused as a commercial adsorbent, although its production cost is high.     

污泥含炭吸附剂对挥发性有机废气吸附实验研究

研究了污泥含炭吸附剂对挥发性有机污染物的吸附特性。结果表明,污泥含炭吸附剂对苯系物的吸附为典型的物理吸附,其吸附甲苯等温线的类型系优惠型吸附等温线,表明具有良好的吸附能力;在吸附反应温度为20℃,气体流量为500 mL/m in(停留时间为0.424 s),甲苯浓度为2 700 mg/m3时,甲苯的饱和吸附容量为150.0 mg/g;同时,研究表明污泥含炭吸附剂对苯系物的饱和吸附容量和吸附强弱次序为二甲苯甲苯苯。结果表明污泥含炭吸附剂适合对中低浓度有机废气的吸附净化。     

The reuse of biosludge as an adsorbent from a petrochemical wastewater treatment plant

Biosludge was obtained from a petrochemical industry's biological wastewater treatment plant. Zinc chloride (ZnCl2) was used as a sludge activation agent during the pyrolytic process. Scanning electron microscope (SEM) image photographs, element composition, surface functional group, and pore structure were analyzed for the sludge adsorbent characteristics. Results indicated the proper ZnCl2-immersed concentration, pyrolytic temperature, and time could produce adsorbent from the biosludge. The optimal conditions for a larger surface area adsorbent were 3 M ZnCl2-immersed sludge pyrolyzed at 600 degrees C for 30 min and washed with 3 N hydrochloric acid (HCl) solution and distilled water. The predominant pore size of the sludge adsorbent was the mesopore.     

ZnCl_2法污泥含炭吸附剂对模拟烟气中气态汞的吸附

采用改进的ZnCl2化学活化法制备污泥含炭吸附剂,利用EDS以及氮吸附等多种测试手段对所制得的污泥含炭吸附剂进行表征,并利用其处理模拟烟气汞污染物,实验结果表明,污泥含炭吸附剂对Hg0的吸附包括物理吸附作用和化学吸附作用,以物理吸附作用为主;随着Hg0入口浓度的提高,污泥含炭吸附剂的Hg0饱和吸附容量增大;随着吸附反应温度的升高污泥含炭吸附对Hg0的吸附作用减弱;在吸附反应温度125℃,Hg0入口浓度60.4 ug/m3,污泥含炭吸附剂和选定的活性炭对Hg0的吸附容量分别为81.2 ug/g和53.8 ug/g,污泥含炭吸附剂对Hg0的吸附作用好于选定的活性炭.     

Fate of nickel in a lime-stabilized biosolid,a calcareous soil and soil–biosolid mixtures

Soil contamination with anthropogenic metals resulting from biosolid application is widespread around the world. To better predict the environmental fate and mobility of contaminants, it is critical to study the capacity of biosolid-amended soils to retain and release metals. In this paper, nickel adsorption onto a calcareous soil, a lime-stabilized biosolid, and soil–biosolid mixtures (30, 75, and 150 t biosolid/ha) was studied in batch experiments. Sorption experiments showed that (1) Ni adsorption was higher onto the biosolid than the calcareous soil, and (2) biosolid acted as an adsorbent in the biosolid–soil mixtures by increasing Ni retention capacity. The sorption tests were complemented with the estimation of Ni adsorption reversibility by successive applications of extraction solutions with water, calcium (100 mg/L), and oxalic acid (equivalent to 100 mg carbon/L). It has been shown that Ni desorption rates in soil and biosolid-amended soils were lower than 30 % whatever the chemical reagent, indicating that Ni was strongly adsorbed on the different systems. This adsorption/desorption hysteresis effect was particularly significant at the highest biosolid concentration (150 t/ha). Finally, an adsorption empirical model was used to estimate the maximum permissible biosolid application rate using French national guideline. It has been shown that desorption effects should be quantitatively considered to estimate relevant biosolid loadings.     

Optimising the preparation of activated carbon from digested sewage sludge and coconut husk.

Preparation of activated carbon from sewage sludge is a promising way to dispose of sewage sludge as well as to produce a low-cost adsorbent for pollutant removal. This research work aimed to optimise the condition for activated carbon preparation from anaerobically digested sewage sludge with the additive coconut husk. The sewage sludge sample was mixed with the additive coconut husk. The preparation condition variables investigated involved the concentration of the ZnCl2 solutions, heating temperature, dwell time and heating rate in pyrolysis and the mixing ratio of coconut husk to sewage sludge. Surface area, pore size distribution, aqueous phenol adsorption capacity and the production yield of the final products were determined and compared. Experimental results revealed that low concentrations of ZnCl2 solution tended to improve the microporosity of the final product. Heating temperature had a considerable impact on the surface area, pore size distribution and phenol adsorption capacity of the final products, whereas dwell time and heating rate performed comparatively insignificantly. The effect of increasing the mixing ratio of coconut husk to sewage sludge was principally to increase the microporosity of the final products. The activated carbon with the highest BET surface area was produced with the activation of 5 M ZnCl2 solution and, thereafter, pyrolysis at a heating temperature of 500 degrees C for 2 h with a heating rate of 10 degrees C/min. The mixing ratio of 1:4 in terms of coconut husk to sewage sludge based on their dried weights was found to be most cost effective.     

顶空气相色谱测试水中苯系混合物在不同材料上的吸附行为

设计了正交实验对5种材料吸附模拟废水中苯系混合物(苯、甲苯、二甲苯)的条件进行优化,CD02硅藻土与X型纳米分子筛以2∶1(质量比)进行复合后,对苯系混合物去除效果最好.采用顶空气相色谱法测定8种不同材料对水中苯系混合物的去除情况,结果表明复合材料对苯系混合物具有良好的去除效果,仅次于活性炭.复合材料在pH为7、搅拌时间为25 min、用量为1.8g/L时,对苯系混合物质量浓度为4.0 mg/L模拟废水的平均去除率为87.56％.经过4次再生后,复合材料的再生率仍高达84.90％,对苯系混合物的平均去除率为91.49％.     

ZnCl2法污泥含炭吸附剂对模拟烟气中气态汞的吸附

采用改进的ZnCl2学活化法制备污泥含炭吸附剂，利用EDS以及氮吸附等多种测试手段对所制得的污泥含炭吸附剂进行表征，并利用其处理模拟烟气汞污染物，实验结果表明，污泥含炭吸附剂对Hg^0吸附包括物理吸附作用和化学吸附作用，以物理吸附作用为主；随着Hg^0入口浓度的提高，污泥含炭吸附剂的Hg^0饱和吸附容量增大；随着吸附反应温度的升高污泥含炭吸附对Hg^0的吸附作用减弱；在吸附反应温度125℃，Hg^0入口浓度60．4μg／m3污泥含炭吸附剂和选定的活性炭对Hg^0吸附容量分别为81．2gg／g和53．8μg／g，污泥含炭吸附剂对Hg^0吸附作用好于选定的活性炭。     

Determination of the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon using thermogravimetric analysis

This study investigated the use of thermogravimetric analysis (TGA) to determine the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon (PAC). The technique is commonly applied to remove mercury-containing air pollutants from gas streams emitted from municipal solid waste incinerators. An alternative form of powdered activated carbon derived from a pyrolyzed tire char was prepared for use herein. The capacity of waste tire-derived PAC to adsorb vapor-phase HgCl2 was successfully measured using a self-designed TGA adsorption system. Experimental results showed that the maximum adsorptive capacities of HgCl2 were 1.75, 0.688, and 0.230 mg of HgCl2 per gram of powdered activated carbon derived from carbon black at 30, 70, and 150 degrees C for 500 microg/m3 of HgCl2, respectively. Four adsorption isotherms obtained using the Langmuir, Freundlich, Redlich-Peterson, and Brunauer-Emmett-Teller (BET) models were used to simulate the adsorption of HgCl2. The comparison of experimental data associated with the four adsorption isotherms indicated that BET fit the experimental results better than did the other isotherms at 30 degrees C, whereas the Freundlich isotherm fit the experimental results better at 70 and 150 degrees C. Furthermore, the calculations of the parameters associated with Langmuir and Freundlich isotherms revealed that the adsorption of HgCl2 by PAC-derived carbon black favored adsorption at various HgCl2, concentrations and temperatures.     

Properties of pyrolytic chars and activated carbons derived from pilot-scale pyrolysis of used tires

Used tires were pyrolyzed in a pilot-scale quasi-inert rotary kiln. Influences of variables, such as time, temperature, and agent flow, on the activation of obtained char were subsequently investigated in a laboratory-scale fixed bed. Mesoporous pores are found to be dominant in the pore structures of raw char. Brunauer-Emmett-Teller (BET) surfaces of activated chars increased linearly with carbon burnoff. The carbon burnoff of tire char achieved by carbon dioxide (CO2) under otherwise identical conditions was on average 75% of that achieved by steam, but their BET surfaces are almost the same. The proper activation greatly improved the aqueous adsorption of raw char, especially for small molecular adsorbates, for example, phenol from 6 to 51 mg/g. With increasing burnoff, phenol adsorption exhibited a first-stage linear increase followed by a rapid drop after 30% burnoff. Similarly, iodine adsorption first increased linearly, but it held as the burnoff exceeded 40%, which implied that the reduction of iodine adsorption due to decreasing micropores was partially made up by increasing mesopores. Both raw chars and activated chars showed appreciable adsorption capacity of methylene-blue comparable with that of commercial carbons. Thus, tire-derived activated carbons can be used as an excellent mesoporous adsorbent for larger molecular species.     

Removal of acutely hazardous pharmaceuticals from water using multi-template imprinted polymer adsorbent

Molecularly imprinted polymer adsorbent has been prepared to remove a group of recalcitrant and acutely hazardous (p-type) chemicals from water and wastewaters. The polymer adsorbent exhibited twofold higher adsorption capacity than the commercially used polystyrene divinylbenzene resin (XAD) and powdered activated carbon adsorbents. Higher adsorption capacity of the polymer adsorbent was explained on the basis of high specific surface area formed during molecular imprinting process. Freundlich isotherms drawn showed that the adsorption of p-type chemicals onto polymer adsorbent was kinetically faster than the other reference adsorbents. Matrix effect on adsorption of p-type chemicals was minimal, and also polymer adsorbent was amenable to regeneration by washing with water/methanol (3:1, v/v) solution. The polymer adsorbent was unaltered in its adsorption capacity up to 10 cycles of adsorption and desorption, which will be more desirable in cost reduction of treatment compared with single-time-use activated carbon.     

Properties of Pyrolytic Chars and Activated Carbons Derived from Pilot-Scale Pyrolysis of Used Tires

Abstract

Used tires were pyrolyzed in a pilot-scale quasi-inert rotary kiln. Influences of variables, such as time, temperature, and agent flow, on the activation of obtained char were subsequently investigated in a laboratory-scale fixed bed. Meso-porous pores are found to be dominant in the pore structures of raw char. Brunauer-Emmett-Teller (BET) surfaces of activated chars increased linearly with carbon burnoff. The carbon burnoff of tire char achieved by carbon dioxide (CO₂) under otherwise identical conditions was on average 75% of that achieved by steam, but their BET surfaces are almost the same. The proper activation greatly improved the aqueous adsorption of raw char, especially for small molecular adsorbates, for example, phenol from 6 to 51 mg/g. With increasing burnoff, phenol adsorption exhibited a first-stage linear increase followed by a rapid drop after 30% burnoff. Similarly, iodine adsorption first increased linearly, but it held as the burnoff exceeded 40%, which implied that the reduction of iodine adsorption due to decreasing micro-pores was partially made up by increasing mesopores. Both raw chars and activated chars showed appreciable adsorption capacity of methylene-blue comparable with that of commercial carbons. Thus, tire-derived activated carbons can be used as an excellent mesoporous adsorbent for larger molecular species.     

Determination of the Adsorption Isotherm of Vapor-Phase Mercury Chloride on Powdered Activated Carbon Using Thermogravimetric Analysis

Abstract

This study investigated the use of thermogravimetric analysis (TGA) to determine the adsorptive capacity and adsorption isotherm of vapor-phase mercury chloride on powdered activated carbon (PAC). The technique is commonly applied to remove mercury-containing air pollutants from gas streams emitted from municipal solid waste incinerators. An alternative form of powdered activated carbon derived from a pyrolyzed tire char was prepared for use herein. The capacity of waste tire-derived PAC to adsorb vapor-phase HgCl₂ was successfully measured using a self-designed TGA adsorption system. Experimental results showed that the maximum adsorptive capacities of HgCl₂ were 1.75, 0.688, and 0.230 mg of HgCl₂ per gram of powdered activated carbon derived from carbon black at 30, 70, and 150 °C for 500 µg/m³ of HgCl₂, respectively. Four adsorption isotherms obtained using the Langmuir, Freundlich, Redlich-Peterson, and Brunauer–Emmett–Teller (BET) models were used to simulate the adsorption of HgCl₂. The comparison of experimental data associated with the four adsorption isotherms indicated that BET fit the experimental results better than did the other isotherms at 30 °C, whereas the Freundlich isotherm fit the experimental results better at 70 and 150 °C. Furthermore, the calculations of the parameters associated with Langmuir and Freundlich isotherms revealed that the adsorption of HgCl₂ by PAC-derived carbon black favored adsorption at various HgCl₂ concentrations and temperatures.     

TiO2/活性炭复合纳米纤维膜对亚甲基蓝的吸附研究

摘要以自制的TiO2/活性炭复合纳米纤维膜作为吸附剂,以亚甲基蓝为目标污染物,研究了亚甲基蓝初始浓度、温度、TiO2/活性炭复合纳米纤维膜投加量、pH等对TiO2/活性炭复合纳米纤维膜吸附去除亚甲基蓝的影响,并研究了TiO2/活性炭复合纳米纤维膜的Zeta电位、接触角、光催化再生性能.结果表明:(1)静态吸附时,随着亚...     

Production of sugarcane bagasse-based activated carbon for formaldehyde gas removal from potted plants exposure chamber

Agricultural wastes such as rice straw, sugar beet, and sugarcane bagasse have become a critical environmental issue due to growing agriculture demand. This study aimed to investigate the valorization possibility of sugarcane bagasse waste for activated carbon preparation. It also aimed to fully characterize the prepared activated carbon (BET surface area) via scanning electron microscope (SEM) and in terms of surface functional groups to give a basic understanding of its structure and to study the adsorption capacity of the sugarcane bagasse-based activated carbon using aqueous methylene blue (MB). The second main objective was to evaluate the performance of sugarcane bagasse-based activated carbon for indoor volatile organic compounds removal using the formaldehyde gas (HCHO) as reference model in two potted plants chambers. The first chamber was labeled the polluted chamber (containing formaldehyde gas without activated carbon) and the second was taken as the treated chamber (containing formaldehyde gas with activated carbon). The results indicated that the sugarcane bagasse-based activated carbon has a moderate BET surface area (557 m²/g) with total mesoporous volume and microporous volume of 0.310 and 0.273 cm³/g, respectively. The prepared activated carbon had remarkable adsorption capacity for MB. Formaldehyde removal rate was then found to be more than 67% in the treated chamber with the sugarcane bagasse-based activated carbon. The plants’ responses for this application as dry weight, chlorophyll contents, and protein concentration were also investigated.

Implications: Preparation of activated carbon from sugarcane bagasse (SCBAC) is a promising approach to produce cheap and efficient adsorbent for gas pollutants removal. It may be also a solution for the agricultural wastes problems in big cities, particularly in Egypt. MB adsorption tests suggest that the SCBAC have high adsorption capacity. Formaldehyde gas removal in the plant chambers indicates that the SCBAC have potential to recover volatile gases. The results confirmed that the activated carbon produced from sugarcane bagasse waste raw materials can be used as an applicable adsorbent for treating a variety of gas pollutants from the indoor environment.     

Analysis and comparison of inertinite-derived adsorbent with conventional adsorbents

To increase U.S. petroleum energy-independence, the University of Texas at Arlington (UT Arlington) has developed a coal liquefaction process that uses a hydrogenated solvent and a proprietary catalyst to convert lignite coal to crude oil. This paper reports on part of the environmental evaluation of the liquefaction process: the evaluation of the solid residual from liquefying the coal, called inertinite, as a potential adsorbent for air and water purification. Inertinite samples derived from Arkansas and Texas lignite coals were used as test samples. In the activated carbon creation process, inertinite samples were heated in a tube furnace (Lindberg, Type 55035, Arlington, UT) at temperatures ranging between 300 and 850 degrees C for time spans of 60, 90, and 120 min, using steam and carbon dioxide as oxidizing gases. Activated inertinite samples were then characterized by ultra-high-purity nitrogen adsorption isotherms at 77 K using a high-speed surface area and pore size analyzer (Quantachrome, Nova 2200e, Kingsville, TX). Surface area and total pore volume were determined using the Brunauer Emmet, and Teller method, for the inertinite samples, as well as for four commercially available activated carbons (gas-phase adsorbents Calgon Fluepac-B and BPL 4 x 6; liquid-phase adsorbents Filtrasorb 200 and Carbsorb 30). In addition, adsorption isotherms were developed for inertinite and the two commercially available gas-phase carbons, using methyl ethyl ketone (MEK) as an example compound. Adsorption capacity was measured gravimetrically with a symmetric vapor sorption analyzer (VTI, Inc., Model SGA-100, Kingsville, TX). Also, liquid-phase adsorption experiments were conducted using methyl orange as an example organic compound. The study showed that using inertinite from coal can be beneficially reused as an adsorbent for air or water pollution control, although its surface area and adsorption capacity are not as high as those for commercially available activated carbons. Implications: The United States currently imports two-thirds of its crude oil, leaving its transportation system especially vulnerable to disruptions in international crude supplies. UT Arlington has developed a liquefaction process that converts coal, abundant in the United States, to crude oil. This work demonstrated that the undissolvable solid coal residual from the liquefaction process, called inertinite, can be converted to an activated carbon adsorbent. Although its surface area and adsorption capacity are not as high as those for commercially available carbons, the inertinite source material would be available at no cost, and its beneficial reuse would avoid the need for disposal.     

黑曲霉死菌与活性炭对直接耐晒翠蓝FBL的吸附性能

采用批式实验,系统考察了黑曲霉死菌和活性炭的粉剂投加量,染料初始浓度,pH和反应时间对酞菁染料FBL脱色效果的影响;并采用扫描电镜图像,分析吸附剂的结构变化。结果表明,对于FBL染料的吸附处理,黑曲霉死菌粉剂与活性炭粉剂适宜的吸附条件为:酸性至弱碱性pH下,投加量为8 g/L;黑曲霉死菌粉剂比活性炭粉剂的吸附速度快、脱色性能高、抗染料浓度负荷冲击能力强。扫描电镜图像分析显示,黑曲霉死菌粉剂所具有的多层纤维结构为吸附染料分子提供较大的比表面。     

80TH APCA Annual Meeting & Exhibition June 21-26, 1987

To increase U.S. petroleum energy-independence, the University of Texas at Arlington (UT Arlington) has developed a coal liquefaction process that uses a hydrogenated solvent and a proprietary catalyst to convert lignite coal to crude oil. This paper reports on part of the environmental evaluation of the liquefaction process: the evaluation of the solid residual from liquefying the coal, called inertinite, as a potential adsorbent for air and water purification. Inertinite samples derived from Arkansas and Texas lignite coals were used as test samples.

In the activated carbon creation process, inertinite samples were heated in a tube furnace (Lindberg, Type 55035, Arlington, UT) at temperatures ranging between 300 and 850 °C for time spans of 60, 90, and 120 min, using steam and carbon dioxide as oxidizing gases. Activated inertinite samples were then characterized by ultra-high-purity nitrogen adsorption isotherms at 77 K using a high-speed surface area and pore size analyzer (Quantachrome, Nova 2200e, Kingsville, TX). Surface area and total pore volume were determined using the Brunauer, Emmet, and Teller method, for the inertinite samples, as well as for four commercially available activated carbons (gas-phase adsorbents Calgon Fluepac-B and BPL 4?×?6; liquid-phase adsorbents Filtrasorb 200 and Carbsorb 30). In addition, adsorption isotherms were developed for inertinite and the two commercially available gas-phase carbons, using methyl ethyl ketone (MEK) as an example compound. Adsorption capacity was measured gravimetrically with a symmetric vapor sorption analyzer (VTI, Inc., Model SGA-100, Kingsville, TX). Also, liquid-phase adsorption experiments were conducted using methyl orange as an example organic compound. The study showed that using inertinite from coal can be beneficially reused as an adsorbent for air or water pollution control, although its surface area and adsorption capacity are not as high as those for commercially available activated carbons.

Implications: The United States currently imports two-thirds of its crude oil, leaving its transportation system especially vulnerable to disruptions in international crude supplies. UT Arlington has developed a liquefaction process that converts coal, abundant in the United States, to crude oil. This work demonstrated that the undissolvable solid coal residual from the liquefaction process, called inertinite, can be converted to an activated carbon adsorbent. Although its surface area and adsorption capacity are not as high as those for commercially available carbons, the inertinite source material would be available at no cost, and its beneficial reuse would avoid the need for disposal.     

Physico-chemical treatments for the complete removal of non-ionic surfactants from effluents

Adsorption isotherms for a selection of non-ionic surfactants on activated carbons indicated the effectiveness of the latter in the removal of these pollutants from secondary effluents. The removal efficiencies were found to be improved when the secondary effluent was first flocculated with ferric chloride. This effectively removed some 80% of the non-ionic surfactant in the effluent. Batch adsorption experiments with powdered activated carbon removed 97% of the surfactant at low carbon dosage. A granular carbon with the best adsorption capacity was selected for continuous-flow operation in which non-ionic surfactants, COD and anionic surfactant alkyl benzene sulphonate were monitored. The breakthrough capacity for the non-ionic surfactants was in excess of 6000 bed volumes throughput of flocculated, sand-filtered effluent in a laboratory scale carbon column. Such a procedure is suggested for the complete removal of such pollutants from effluents.     

Activated carbon from industrial solid waste as an adsorbent for the removal of Rhodamine-B from aqueous solution: kinetic and equilibrium studies

The activated carbon was prepared using industrial solid waste called sago waste and physico-chemical properties of carbon were carried out to explore adsorption process. The effectiveness of carbon prepared from sago waste in adsorbing Rhodamine-B from aqueous solution has been studied as a function of agitation time, adsorbent dosage, initial dye concentration, pH and desorption. Adsorption equilibrium studies were carried out in order to optimize the experimental conditions. The adsorption of Rhodamine-B onto carbon followed second order kinetic model. Adsorption data were modeled using both Langmuir and Freundlich classical adsorption isotherms. The adsorption capacity Q0 was 16.12 mg g(-1) at initial pH 5.7 for the particle size 125-250 microm. The equilibrium time was found to be 150 min for 10, 20 mg l(-1) and 210 min for 30, 40 mg l(-1) dye concentrations, respectively. A maximum removal of 91% was obtained at natural pH 5.7 for an adsorbent dose of 100mg/50 ml of 10 mg l(-1) dye concentration and 100% removal was obtained when the pH was increased to 7 for an adsorbent dose of 275 mg/50 ml of 20 mg l(-1) dye concentration. Desorption studies were carried out in water medium by varying the pH from 2 to 10. Desorption studies were performed with dilute HCl and show that ion exchange is predominant dye adsorption mechanism. This adsorbent was found to be both effective and economically viable.