Investigation of PM2.5 and carbon dioxide levels in urban homes

PM_2.5 (particulate matter with an aerodynamic diameter <2.5 μm) samples were collected in the indoor environments of 15 urban homes and their adjacent outdoor environments in Alexandria, Egypt, during the spring time. Indoor and outdoor carbon dioxide (CO₂) levels were also measured concurrently. The results showed that indoor and outdoor PM_2.5 concentrations in the 15 sites, with daily averages of 45.5 ± 11.1 and 47.3 ± 12.9 µg/m³, respectively, were significantly higher than the ambient 24-hr PM_2.5 standard of 35 µg/m³ recommended by the U.S. Environmental Protection Agency (EPA). The indoor PM_2.5 and CO₂ levels were correlated with the corresponding outdoor levels, demonstrating that outdoor convection and infiltration could lead to direct transportation indoors. Ventilation rates were also measured in the selected residences and ranged from 1.6 to 4.5 hr^?1 with median value of 3.3 hr^?1. The indoor/outdoor (I/O) ratios of the monitored homes varied from 0.73 to 1.65 with average value of 0.99 ± 0.26 for PM_2.5, whereas those for CO₂ ranged from 1.13 to 1.66 with average value of 1.41 ± 0.15. Indoor sources and personal activities, including smoking and cooking, were found to significantly influence indoor levels.

Implications: Few studies on indoor air quality were carried out in Egypt, and the scarce data resulted from such studies do not allow accurate assessment of the current situation to take necessary preventive actions. The current research investigates indoor levels of PM_2.5 and CO₂ in a number of homes located in the city of Alexandria as well as the potential contribution from both indoor and outdoor sources. The study draws attention of policymakers to the importance of the establishment of national indoor air quality standards to protect human health and control air pollution in different indoor environments.     

Outdoor and indoor factors influencing particulate matter and carbon dioxide levels in naturally ventilated urban homes

ABSTRACT

The present study investigated indoor and outdoor concentrations of two particulate matter size fractions (PM₁₀ and PM_2.5) and CO₂ in 20 urban homes ventilated naturally and located in one congested residential and commercial area in the city of Alexandria, Egypt. The results indicate that the daily mean PM_2.5 concentrations measured in the ambient air, living rooms, and kitchens of all sampling sites exceeded the WHO guideline by 100%, 65%, and 95%, respectively. The daily mean outdoor and indoor PM₁₀ levels in all sampling sites were found to exceed the WHO guideline by 100% and 80%, respectively. The indoor PM₁₀ and PM_2.5 concentrations were significantly correlated with their corresponding outdoor levels, as natural ventilation through opening doors and windows allowed direct transfer of outdoor airborne particles into the indoor air. Most of the kitchens investigated had higher indoor concentrations of PM_2.5 and CO₂ than in living rooms. The elevated levels of PM_2.5 and CO₂ in domestic kitchens were probably related to inadequate ventilation. The current study attempted to understand the sources and the various indoor and outdoor factors that affect indoor PM₁₀, PM_2.5 and CO₂ concentrations. Several domestic activities, such as smoking, cooking, and cleaning, were found to constitute important sources of indoor air pollution. The indoor pollution caused by PM_2.5 was also found to be more serious in the domestic kitchens than in the living rooms and the results suggest that exposure to PM_2.5 is high and highlights the need for more effective control measures.

Implications: Indoor air pollution is a complex problem that involves many determinant factors. Understanding the relationships and the influence of various indoor and outdoor factors on indoor air quality is very important to prioritize control measures and mitigation action plans. There is currently a lack of research studies in Egypt to investigate determinant factors controlling indoor air quality for urban homes. The present study characterizes the indoor and outdoor concentrations of PM₁₀, PM_2.5, and CO₂ in residential buildings in Alexandria city. The study also determines the indoor and outdoor factors which influence the indoor PM and CO₂ concentrations as well as it evaluates the potential indoor sources in the selected homes. This research will help in the development of future indoor air quality standards for Egypt.     

An assessment of indoor air quality in recent Mexican immigrant housing in Commerce City, Colorado

An indoor air quality assessment was conducted on 100 homes of recent Mexican immigrants in Commerce City, Colorado, an urban industrial community north of Denver. Head of households were administered a family health survey, filled out an activity diary, and participated in a home inspection. Carbon monoxide (CO) and carbon dioxide (CO₂) were measured for 24 h inside the main living area and outside of the homes. Harvard Impactors were used to collect 24-h samples of PM_2.5 at the same locations for gravimetric analysis. Dust samples were collected by vacuuming carpeting and flooring at four locations within the home and analyzed by ELISA for seven allergens. Mean indoor and outdoor PM_2.5 levels were 27.2 and 8.5 μg m⁻³, respectively. Indoor PM_2.5 and CO₂ were elevated in homes for which the number of hours with door/window open was zero compared to homes in which the number of hours was high (>15 h). Indoor PM_2.5 levels did not correlate with outdoor levels and tended to increase with number of inhabitants, and results indicate that the source of indoor particles were occupants and their activities, excluding smoking and cooking. Mean indoor CO₂ and CO levels were 1170 and 2.4 ppm, respectively. Carbon monoxide was higher than the 24-h National Ambient Air Quality Standard in 3 of the homes. The predominant allergens were cat (Fel d 1) and mouse (Mus m 1) allergens, found in 20 and 34 homes, respectively.     

Particulate matter and manganese exposures in Toronto,Canada

Methylcyclopentadienyl manganese tricarbonyl (MMT) is a manganese-based gasoline additive used to enhance automobile performance. MMT has been used in Canadian gasoline for about 20 yr. Because of the potential for increased levels of Mn in particulate matter resulting from automotive exhausts, a large-scale population-based exposure study (∼1000 participant periods) was conducted in Toronto, Canada, to estimate the distribution of 3-day average personal exposures to particulate matter (PM_2.5 and PM₁₀) and Mn. A stratified, three-stage, two-phase probability, longitudinal sample design of the metropolitan population was employed. Residential indoor and outdoor, and ambient levels (at a fixed site and on a roof) of PM_2.5, PM₁₀, and Mn were also measured. Supplementary data on traffic counts, meteorology, MMT levels in gasoline, personal occupations, and activities (e.g. amount of vehicular usage) were collected. Overall precision (%RSD) for analysis of duplicate co-located samples ranged from 2.5 to 5.0% for particulate matter and 3.1 to 5.5% for Mn. The detection limits were 1.47 and 3.45 μg m^-3 for the PM₁₀ and PM_2.5 fractions, respectively, and 5.50 and 1.83 ng m^-3 for Mn in PM₁₀ and PM_2.5, respectively. These low detection limits permitted the reporting of concentrations for >98% of the samples. For PM₁₀, the personal particulate matter levels (median 48.5 μg m^-3) were much higher than either indoor (23.1 μg m^-3) or outdoor levels (23.6 μg m^-3). The median levels for PM_2.5 for personal, indoor, and outdoor were 28.4, 15.4 and 13.2 μg m^-3, respectively. The correlation between PM_2.5 personal exposures and indoor concentrations was high (0.79), while correlations between personal and the outdoor, fixed site and roof site were low (0.16–0.27). Indoor Mn concentration distributions (in PM_2.5 and PM₁₀), unlike particulate matter, exhibited much lower and less variable levels that the corresponding outdoor data. The median personal exposure was 8.0 ng m^-3, compared with 4.7 and 8.6 ng m^-3, respectively, for the indoor and outdoor distributions. The highest correlations occurred for personal vs indoor data (0.56) and for outdoor vs roof site data (0.66), and vs fixed site data (0.56). The concentration of Mn in particulate matter, expressed in ppm (w/w), revealed that the fixed site was the highest, followed by the roof site, outdoor, indoor, and personal. The personal and indoor data showed a statistically significant correlation (0.68) while all other correlations between personal or indoor data and outdoor or fixed-site data were quite small. The low correlations of personal and indoor levels with outdoor levels suggest that different sources in the indoor and outdoor microenvironments produce particle matter with dissimilar composition. The correlation results indicate that neither the roof- nor fixed-site concentrations can adequately predict personal particulate matter or Mn exposures.     

Associations between particle physicochemical characteristics and oxidative capacity: An indoor PM10 study in Beijing,China

A study was undertaken to determine the use of a plasmid DNA scission assay to evaluate the causal relationships between particle oxidative capacity and physico-chemistry. Field emission scanning electron microscopy (FESEM), image analysis (IA) and inductively coupled plasma-mass spectrometry (ICP-MS) were employed to investigate the physico-chemical characteristics of indoor PM₁₀ (particulate matter with an aerodynamic diameter of 10 μm or less) in Beijing, China. Six PM₁₀ samples (indoor smoker's living room; indoor non-smoker's living room and kitchen; and outdoor Beijing city; winter versus summer) were selected to represent typical indoor Beijing PM₁₀ environments that contain high particle mass. The PM₁₀ collected from a kitchen and two smoker's homes had the lowest TD₅₀ (toxic dosage of PM₁₀ causing 50% plasmid DNA damage), being as low as 45 μg ml⁻¹ (kitchen) and 100 μg ml⁻¹ (living room), which suggests a high oxidative capacity, with the PM₁₀ generated in kitchens appearing to be the most toxic. The indoor PM₁₀ from the non-smoker's home and outdoor PM₁₀ samples demonstrated high TD₅₀ values and were deemed less bioreactive (i.e. caused limited DNA damage). FESEM observations revealed that four types of particle species were prevalent in Beijing indoor PM₁₀; soot aggregates, minerals, coal fly ash and unknown fine particles. IA showed that higher percentages of soot and unknown fine particles were associated with the lower TD₅₀ values, suggesting that soot and the unknown fine particles may be important components responsible for the observed plasmid DNA damage. The water-soluble trace elements were negatively correlated with the TD₅₀ values, implying that the DNA damage may be attributed to the water-soluble fraction of the PM₁₀. Water-soluble zinc revealed the best relationship with the TD₅₀ values than other analyzed elements, signifying it may play a role in driving the oxidative damage.     

Behavioral and environmental determinants of personal exposures to PM2.5 in EXPOLIS – Helsinki,Finland

Behavioral and environmental determinants of PM_2.5 personal exposures were analyzed for 201 randomly selected adult participants (25–55 years old) of the EXPOLIS study in Helsinki, Finland. Personal exposure concentrations were higher than respective residential outdoor, residential indoor and workplace indoor concentrations for both smokers and non-smokers. Mean personal exposure concentrations of active smokers (31.0±31.4 μg m⁻³) were almost double those of participants exposed to environmental tobacco smoke (ETS) (16.6±11.8 μg m⁻³) and three times those of participants not exposed to tobacco smoke (9.9±6.2 μg m⁻³). Mean indoor concentrations of PM_2.5 when a member of the household smoked indoors (20.8±23.9 μg m⁻³) were approximately 2.5 times the concentrations of PM_2.5 when no smoking was reported (8.2±5.2 μg m⁻³). Interestingly, however, both mean (8.2 μg m⁻³) and median (6.9 μg m⁻³) residential indoor concentrations for non-ETS exposed participants were lower than residential outdoor concentrations (9.5 and 7.3 μg m⁻³, respectively). In simple linear regression models residential indoor concentrations were the best predictors of personal exposure concentrations. Correlations (r²) between PM_2.5 personal exposure concentrations of all participants, both smoking and non-smoking, and residential indoor, workplace indoor, residential outdoor and ambient fixed site concentrations were 0.53, 0.38, 0.17 and 0.16, respectively. Predictors for personal exposure concentrations of non-ETS exposed participants identified in multiple regression were residential indoor concentrations, workplace concentrations and traffic density in the nearest street from home, which accounted for 77% of the variance. Subsequently, step-wise regression not including residential and workplace indoor concentrations as input (as these are frequently not available), identified ambient PM_2.5 concentration and home location, as predictors of personal exposure, accounting for 47% of the variance. Ambient fixed site PM_2.5 concentrations were closely related to residential outdoor concentrations (r²=0.9, p=0.000) and PM_2.5 personal exposure concentrations were higher in summer than during other seasons. Personal exposure concentrations were significantly (p=0.040) higher for individuals living downtown compared with individuals in suburban family homes. Further analysis will focus on comparisons of determinants between Helsinki and other EXPOLIS centers.     

A functional group characterization of organic PM2.5 exposure: Results from the RIOPA study

The functional group (FG) composition of urban residential outdoor, indoor, and personal fine particle (PM_2.5) samples is presented and used to provide insights relevant to organic PM_2.5 exposure. PM_2.5 samples (48 h) were collected during the Relationship of Indoor, Outdoor, and Personal Air (RIOPA) study at 219 non-smoking homes (once or twice) in Los Angeles County, CA, Elizabeth, NJ, and Houston, TX. Fourier transform infrared (FTIR) spectra of PM_2.5 samples were collected, and FG absorbances were quantified by partial least squares (PLS) regression, a multivariate calibration method.There is growing evidence in the literature that a large majority of indoor-generated PM_2.5 is organic. The current research suggests that indoor-generated PM_2.5 is enriched in aliphatic carbon–hydrogen (CH) FGs relative to ambient outdoor PM_2.5. Indoor-generated CH exceeded outdoor-generated CH in 144 of the 167 homes for which indoor or outdoor CH was measurable; estimated indoor emission rates are provided. The strong presence of aliphatic CH FGs in indoor PM_2.5 makes particulate organic matter substantially less polar indoors and in personal exposures than outdoors. This is a substantial new finding. Based on the quantified FGs, the average organic molecular weight (OM) per carbon weight (OC), a measure of the degree of oxygenation of organic PM, is in the range of 1.7–2.6 for outdoor samples and 1.3–1.7 for indoor and personal samples. Polarity or degree of oxygenation effects particle deposition in exposure environments and in the respiratory system.     

Air pollutants in rural homes in Guizhou,China – Concentrations,speciation, and size distribution

Several types of fuels, including coal, fuel wood, and biogas, are commonly used for cooking and heating in Chinese rural households, resulting in indoor air pollution and causing severe health impacts. In this paper, we report a study monitoring multiple pollutants including PM₁₀, PM_2.5, CO, CO₂, and volatile organic compounds (VOCs) from fuel combustion at households in Guizhou province of China. The results showed that most pollutants exhibited large variability for different type of fuels except for CO₂. Among these fuels, wood combustion caused the most serious indoor air pollution, with the highest concentrations of particulate matters (218～417 μg m^?3 for PM₁₀ and 201～304 μg m^?3 for PM_2.5), and higher concentrations of CO (10.8 ± 0.8 mg m^?3) and TVOC (about 466.7 ± 337.9 μg m^?3). Coal combustion also resulted in higher concentrations of particulate matters (220～250 μg m^?3 for PM₁₀ and 170～200 μg m^?3 for PM_2.5), but different levels for CO (respectively 14.5 ± 3.7 mg m^?3 for combustion in brick stove and 5.5 ± 0.7 mg m^?3 for combustion in metal stove) and TVOC (170 mg m^?3 for combustion in brick stove and 700 mg m^?3 for combustion in metal stove). Biogas was the cleanest fuel, which brought about the similar levels of various pollutants with the indoor case of non-combustion, and worth being promoted in more areas. Analysis of the chemical profiles of PM_2.5 indicated that OC and EC were dominant components for all fuels, with the proportions of 30～48%. A high fraction of SO₄^2? (31～34%) was detected for coal combustion. The cumulative percentages of these chemical species were within the range of 0.7～1.3, which was acceptable for the assessment of mass balance.     

The effects of evaporating essential oils on indoor air quality

Essential oils, predominantly comprised of a group of aromatic chemicals, have attracted increasing attention as they are introduced into indoor environments through various forms of consumer products via different venues. Our study aimed to characterize the profiles and concentrations of emitted volatile organic compounds (VOCs) when evaporating essential oils indoors. Three popular essential oils in the market, lavender, eucalyptus, and tea tree, based on a nation-wide questionnaire survey, were tested. Specific aromatic compounds of interest were sampled during evaporating the essential oils, and analyzed by GC-MS. Indoor carbon monoxide (CO), carbon dioxide (CO₂), total volatile organic compounds (TVOCs), and particulate matters (PM₁₀) were measured by real-time, continuous monitors, and duplicate samples for airborne fungi and bacteria were collected in different periods of the evaporation. Indoor CO (average concentration 1.48 vs. 0.47 ppm at test vs. background), CO₂ (543.21 vs. 435.47 ppm), and TVOCs (0.74 vs. 0.48 ppm) levels have increased significantly after evaporating essential oils, but not the PM₁₀ (2.45 vs. 2.42 ppm). The anti-microbial activity on airborne microbes, an effect claimed by the use of many essential oils, could only be found at the first 30–60 min after the evaporation began as the highest levels of volatile components in these essential oils appeared to emit into the air, especially in the case of tea tree oil. High emissions of linalool (0.092–0.787 mg m⁻³), eucalyptol (0.007–0.856 mg m⁻³), d-limonene (0.004–0.153 mg m⁻³), ρ-cymene (0.019–0.141 mg m⁻³), and terpinene-4-ol-1 (0.029–0.978 mg m⁻³), all from the family of terpenes, were observed, and warranted for further examination for their health implications, especially for their potential contribution to the increasing indoor levels of secondary pollutants such as formaldehyde and secondary organic aerosols (SOAs) in the presence of ozone.     

Particulate matter in the indoor air of classrooms—exploratory results from Munich and surrounding area

Numerous epidemiological studies have demonstrated the association between particle mass (PM) concentration in outside air and the occurrence of health related problems and/or diseases. However, much less is known about indoor PM concentrations and associated health risks. In particular, data are needed on air quality in schools, since children are assumed to be more vulnerable to health hazards and spend a large part of their time in classrooms.On this background, we evaluated indoor air quality in 64 schools in the city of Munich and a neighbouring district outside the city boundary. In winter 2004–2005 in 92 classrooms, and in summer 2005 in 75 classrooms, data on indoor air climate parameters (temperature, relative humidity), carbon dioxide (CO₂) and various dust particle fractions (PM₁₀, PM_2.5) were collected; for the latter both gravimetrical and continuous measurements by laser aerosol spectrometer (LAS) were implemented. In the summer period, the particle number concentration (PNC), was determined using a scanning mobility particle sizer (SMPS). Additionally, data on room and building characteristics were collected by use of a standardized form. Only data collected during teaching hours were considered in analysis. For continuously measured parameters the daily median was used to describe the exposure level in a classroom.The median indoor CO₂ concentration in a classroom was 1603 ppm in winter and 405 ppm in summer. With LAS in winter, median PM concentrations of 19.8 μg m⁻³ (PM_2.5) and 91.5 μg m⁻³ (PM₁₀) were observed, in summer PM concentrations were significantly reduced (median PM_2.5=12.7 μg m⁻³, median PM₁₀=64.9 μg m⁻³). PM_2.5 concentrations determined by the gravimetric method were in general higher (median in winter: 36.7 μg m⁻³, median in summer: 20.2 μg m⁻³) but correlated strongly with the LAS-measured results. In explorative analysis, we identified a significant increase of LAS-measured PM_2.5 by 1.7 μg m⁻³ per increase in humidity by 10%, by 0.5 μg m⁻³ per increase in CO₂ indoor concentration by 100 ppm, and a decrease by 2.8 μg m⁻³ in 5–7th grade classes and by 7.3 μg m⁻³ in class 8–11 compared to 1–4th class. During the winter period, the associations were stronger regarding class level, reverse regarding humidity (a decrease by 6.4 μg m⁻³ per increase in 10% humidity) and absent regarding CO₂ indoor concentration. The median PNC measured in 36 classrooms ranged between 2622 and 12,145 particles cm⁻³ (median: 5660 particles cm⁻³).The results clearly show that exposure to particulate matter in school is high. The increased PM concentrations in winter and their correlation with high CO₂ concentrations indicate that inadequate ventilation plays a major role in the establishment of poor indoor air quality. Additionally, the increased PM concentration in low level classes and in rooms with high number of pupils suggest that the physical activity of pupils, which is assumed to be more pronounced in younger children, contributes to a constant process of resuspension of sedimented particles. Further investigations are necessary to increase knowledge on predictors of PM concentration, to assess the toxic potential of indoor particles and to develop and test strategies how to ensure improved indoor air quality in schools.     

Indoor particulate matter in urban residences of Alexandria,Egypt

Indoor particulate matter samples were collected in 17 homes in an urban area in Alexandria during the summer season. During air measurement in all selected homes, parallel outdoor air samples were taken in the balconies of the domestic residences. It was found that the mean indoor PM_2.5 and PM₁₀ (particulate matter with an aerodynamic diameter ≤2.5 and ≤10 μm, respectively) concentrations were 53.5 ± 15.2 and 77.2 ± 15.1 µg/m³, respectively. The corresponding mean outdoor levels were 66.2 ± 16.5 and 123.8 ± 32.1 µg/m³, respectively. PM_2.5 concentrations accounted, on average, for 68.8 ± 12.8% of the total PM₁₀ concentrations indoors, whereas PM_2.5 contributed to 53.7 ± 4.9% of the total outdoor PM₁₀ concentrations. The median indoor/outdoor mass concentration (I/O) ratios were 0.81 (range: 0.43–1.45) and 0.65 (range: 0.4–1.07) for PM_2.5 and PM₁₀, respectively. Only four homes were found with I/O ratios above 1, indicating significant contribution from indoor sources. Poor correlation was seen between the indoor PM₁₀ and PM_2.5 levels and the corresponding outdoor concentrations. PM₁₀ levels were significantly correlated with PM_2.5 loadings indoors and outdoors and this might be related to PM₁₀ and PM_2.5 originating from similar particulate matter emission sources. Smoking, cooking using gas stoves, and cleaning were the major indoor sources contributed to elevated indoor levels of PM₁₀ and PM_2.5.

Implications: The current study presents results of the first PM_2.5 and PM₁₀ study in homes located in the city of Alexandria, Egypt. Scarce data are available on indoor air quality in Egypt. Poor correlation was seen between the indoor and outdoor particulate matter concentrations. Indoor sources such as smoking, cooking, and cleaning were found to be the major contributors to elevated indoor levels of PM₁₀ and PM_2.5.     

Measurements of fine and ultrafine particles formation in photocopy centers in Taiwan

This study investigates the levels of particulate matter smaller than 2.5 μm (PM_2.5) and some selected volatile organic compounds (VOCs) at 12 photocopy centers in Taiwan from November 2004 to June 2005. The results of BTEXS (benzene, toluene, ethylbenzene, xylenes and styrene) measurements indicated that toluene had the highest concentration in all photocopy centers, while the concentration of the other four compounds varied among the 12 photocopy centers. The average background-corrected eight-hour PM_2.5 in the 12 photocopy centers ranged from 10 to 83 μg m⁻³ with an average of 40 μg m⁻³. The 24-h indoor PM_2.5 at the photocopy centers was estimated and at two photocopy centers exceeded 100 μg m⁻³, the 24-h indoor PM_2.5 guideline recommended by the Taiwan EPA. The ozone level and particle size distribution at another photocopy center were monitored and indicated that the ozone level increased when the photocopying started and the average ozone level at some photocopy centers during business hour may exceed the value (50 ppb) recommended by the Taiwan EPA. The particle size distribution monitored during photocopying indicated that the emitted particles were much smaller than the original toner powders. Additionally, the number concentration of particles that were smaller than 0.5 μm was found to increase during the first hour of photocopying and it increased as the particle size decreased. The ultrafine particle (UFP, <100 nm) dominated the number concentration and the peak concentration appeared at sizes of under 50 nm. A high number concentration of UFP was found with a peak value of 1E+8 particles cm⁻³ during photocopying. The decline of UFP concentration was observed after the first hour and the decline is likely attributable to the surface deposition of charged particles, which are charged primarily by the diffusion charging of corona devices in the photocopier. This study concludes that ozone and UFP concentrations in photocopy centers should be concerned in view of indoor air quality and human health. The corona devices in photocopiers and photocopier-emitted VOCs have the potential to initiate indoor air chemistry during photocopying and result in the formation of UFP.     

Effect of Gas and Kerosene Space Heaters on Indoor Air Quality: A Study in Homes of Santiago,Chile

Abstract

The impact of outdoor and indoor pollution sources on indoor air quality in Santiago, Chile was investigated. Toward this end, 16 homes were sampled in four sessions. Each session included an outdoor site and four homes using different unvented space heaters (electric or central heating, compressed natural gas, liquefied petroleum gas, and kerosene). Average outdoor fine particulate matter (PM_2.5) concentrations were very high (55.9 μg·m^-3), and a large fraction of these particles penetrated indoors. PM_2.5 and several PM_2.5 components (including sulfate, elemental carbon, organic carbon, metals, and polycyclic aromatic hydrocarbons) were elevated in homes using kerosene heaters. Nitrogen dioxide (NO₂) and ultrafine particles (UFPs) were higher in homes with combustion heaters as compared with those with electric heaters or central heating. A regression model was used to assess the effect of heater use on continuous indoor PM_2.5 concentrations when windows were closed. The model found an impact only for kerosene heaters (45.8 μg m^-3).     

Exposure assessment of air pollutants: a review on spatial heterogeneity and indoor/outdoor/personal exposure to suspended particulate matter,nitrogen dioxide and ozone

This review describes databases of small-scale spatial variations and indoor, outdoor and personal measurements of air pollutants with the main focus on suspended particulate matter, and to a lesser extent, nitrogen dioxide and photochemical pollutants. The basic definitions and concepts of an exposure measurement are introduced as well as some study design considerations and implications of imprecise exposure measurements. Suspended particulate matter is complex with respect to particle size distributions, the chemical composition and its sources. With respect to small-scale spatial variations in urban areas, largest variations occur in the ultrafine (<0.1 μm) and the coarse mode (PM_10–2.5, resuspended dust). Secondary aerosols which contribute to the accumulation mode (0.1–2 μm) show quite homogenous spatial distribution. In general, small-scale spatial variations of PM_2.5 were described to be smaller than the spatial variations of PM₁₀. Recent studies in outdoor air show that ultrafine particle number counts have large spatial variations and that they are not well correlated to mass data. Sources of indoor particles are from outdoors and some specific indoor sources such as smoking and cooking for fine particles or moving of people (resuspension of dust) for coarse particles. The relationships between indoor, outdoor and personal levels are complex. The finer the particle size, the better becomes the correlation between indoor, outdoor and personal levels. Furthermore, correlations between these parameters are better in longitudinal analyses than in cross-sectional analyses. For NO₂ and O₃, the air chemistry is important. Both have considerable small-scale spatial variations within urban areas. In the absence of indoor sources such as gas appliances, NO₂ indoor/outdoor relationships are strong. For ozone, indoor levels are quite small. The study hypothesis largely determines the choice of a specific concept in exposure assessment, i.e. whether personal sampling is needed or if ambient monitoring is sufficient. Careful evaluation of the validity and improvements in precision of an exposure measure reduce error in the measurements and bias in the exposure–effect relationship.     

Multiple comparisons of organic,microbial, and fine particulate pollutants in typical indoor environments: Diurnal and seasonal variations

This study was performed to investigate the possible sources as well as seasonal and diurnal variations of indoor air pollutants in widely used four different environments (house, office, kindergarten, and primary school) in which people spend most of their time. Bioaerosol levels and species, volatile organic compound (VOC) levels, and PM_2.5 (particulate matter with an aerodynamic diameter ≤2.5 μm) levels were determined in different parts of these environments in parallel with outdoor sampling. Air pollution samplings were carried out in each microenvironment during five subsequent days in both winter and summer in Ankara, Turkey. The results indicated that bioaerosol, VOC, and PM_2.5 levels were higher in the winter than in the summer. Moreover, PM_2.5 and bioaerosol levels showed remarkable daily and diurnal variations, whereas a good correlation was found between the VOC levels measured in the morning and in the afternoon. Bacteria levels were, in general, higher than fungi levels. Among the VOCs, toluene was the most predominant, whereas elevated n-hexane levels were also observed in the kindergarten and the primary school, probably due to the frequent wet cleaning during school days. According to factor analysis, several factors were found to be significantly influencing the indoor air quality (IAQ), and amongst them, VOC-based products used indoors ranked first. The overall results indicate that grab sampling in naturally ventilated places may overestimate or underestimate the IAQ due to the inhomogeneous composition of indoor air caused by irregular exchanges with the outdoor air according to the season and/or occupants' habits.

Implications Seasonal and diurnal variations of VOCs, PM_2.5, bioaerosols in house, office, and schools were observed, in which PM_2.5 and bioaeorosols showed marked both intra- and interday variability, but VOCs did not. VOC-containing products were the most common source of air pollutants affecting the indoor air quality. External factors affecting the indoor air quality were season and indirectly ventilation. A grab sample cannot be representative in evaluating the air quality of a naturally ventilated environment precisely.     

Predicting residential indoor concentrations of nitrogen dioxide,fine particulate matter,and elemental carbon using questionnaire and geographic information system based data

Previous studies have identified associations between traffic-related air pollution and adverse health effects. Most have used measurements from a few central ambient monitors and/or some measure of traffic as indicators of exposure, disregarding spatial variability and factors influencing personal exposure-ambient concentration relationships. This study seeks to utilize publicly available data (i.e., central site monitors, geographic information system, and property assessment data) and questionnaire responses to predict residential indoor concentrations of traffic-related air pollutants for lower socioeconomic status (SES) urban households.As part of a prospective birth cohort study in urban Boston, we collected indoor and outdoor 3–4 day samples of nitrogen dioxide (NO₂) and fine particulate matter (PM_2.5) in 43 low SES residences across multiple seasons from 2003 to 2005. Elemental carbon (EC) concentrations were determined via reflectance analysis. Multiple traffic indicators were derived using Massachusetts Highway Department data and traffic counts collected outside sampling homes. Home characteristics and occupant behaviors were collected via a standardized questionnaire. Additional housing information was collected through property tax records, and ambient concentrations were collected from a centrally located ambient monitor.The contributions of ambient concentrations, local traffic and indoor sources to indoor concentrations were quantified with regression analyses. PM_2.5 was influenced less by local traffic but had significant indoor sources, while EC was associated with traffic and NO₂ with both traffic and indoor sources. Comparing models based on covariate selection using p-values or a Bayesian approach yielded similar results, with traffic density within a 50 m buffer of a home and distance from a truck route as important contributors to indoor levels of NO₂ and EC, respectively. The Bayesian approach also highlighted the uncertanity in the models. We conclude that by utilizing public databases and focused questionnaire data we can identify important predictors of indoor concentrations for multiple air pollutants in a high-risk population.     

Levels and risks of particulate-bound PAHs in indoor air influenced by tobacco smoke: a field measurement

Considering tobacco smoke as one of the most health-relevant indoor sources, the aim of this work was to further understand its negative impacts on human health. The specific objectives of this work were to evaluate the levels of particulate-bound PAHs in smoking and non-smoking homes and to assess the risks associated with inhalation exposure to these compounds. The developed work concerned the application of the toxicity equivalency factors approach (including the estimation of the lifetime lung cancer risks, WHO) and the methodology established by USEPA (considering three different age categories) to 18 PAHs detected in inhalable (PM₁₀) and fine (PM_2.5) particles at two homes. The total concentrations of 18 PAHs (Σ_PAHs) was 17.1 and 16.6 ng m^?3 in PM₁₀ and PM_2.5 at smoking home and 7.60 and 7.16 ng m^?3 in PM₁₀ and PM_2.5 at non-smoking one. Compounds with five and six rings composed the majority of the particulate PAHs content (i.e., 73 and 78 % of Σ_PAHs at the smoking and non-smoking home, respectively). Target carcinogenic risks exceeded USEPA health-based guideline at smoking home for 2 different age categories. Estimated values of lifetime lung cancer risks largely exceeded (68–200 times) the health-based guideline levels at both homes thus demonstrating that long-term exposure to PAHs at the respective levels would eventually cause risk of developing cancer. The high determined values of cancer risks in the absence of smoking were probably caused by contribution of PAHs from outdoor sources.     

Dust build-up on surfaces in the indoor environment

The concentration and the composition of dust in the indoor environment has been associated with reported symptoms of the sick building syndrome. Levels of airborne concentrations of dust particles are well known. However, the relation to dust on surfaces for office environments are not well described. In this study, 662 measurements were performed of surface dust concentrations on hard surfaces in 19 buildings within Harvard University based on a sticking gelatine foil method. The measure is the dust covered area of the surface as a percentage. In three offices, the build-up of dust on surfaces was measured for a period of five days. Close to these surfaces the airborne PM_2.5 and PM₁₀ particle mass concentrations were measured simultanously. A significant correlation between the dust build-up and the difference between the PM₁₀ and the PM_2.5 was established. The particle size distribution was measured by means of an Aerodynamic Particle Sizer. The mean dust build-up normalized with the measured PM₁₀ was approximately four times higher than the equivalent calculated by a deposition model. This may in part be due to the effect of preferred orientation when particles settle to a surface. Different data for dust on surfaces and airborne particles in offices were compared. The levels of airborne particles in offices in Europe seem to be higher than the levels in the US.     

Use of passive samplers to measure atmospheric ammonia levels in a high-density industrial hog farm area of eastern North Carolina

Hog concentrated animal feeding operations (CAFOs) in North Carolina release ammonia (NH₃), hydrogen sulfide, VOCs, and particulate matter to the atmosphere. These operations are located mainly in the NC coastal plain and can create potential health hazards for nearby human populations. Limited work has been performed to measure NH₃ at the community level to assess potential human exposure. In an effort to address this issue, a study was designed to measure NH₃ levels near hog CAFOs and community locations (i.e. homes and schools) in Eastern NC.NH₃ was collected using passive diffusion tubes in triplicate exposed primarily in weekly intervals. Sampling occurred from October 2003 to May 2004 (20 sites) and from July 2004 to October 2004 (23 sites) at varying distances from hog CAFOs in close proximity to homes and schools. Average weekly NH3 levels were measured as mass (μg NH₃-N) and converted to concentration (ppb). Mean level of 13.8 ppb near homes and schools (<2 km) was 4–12 times greater than ambient background levels (1–3 ppb), reaching as high as 80 ppb. Exposed sites (<2 km from a hog CAFO) had a mean level of 12.8 ppb which was over 2 times higher than the mean level of 5.5 ppb at less exposed sites (>2 km from a hog CAFO).The study establishes that passive sampling can be effectively used to measure average atmospheric ammonia levels at community locations near hog CAFOs in Eastern NC. The collected data indicate the relative exposure for human populations who live near a hog CAFO. The closer a populace is to the hog CAFO, the more intense the exposure. These results require more validation in the field by comparison to a reference method.     

Levels of outdoor PM2.5, absorbance and sulphur as surrogates for personal exposures among post-myocardial infarction patients in Barcelona,Spain

Outdoor levels of fine particles (PM_2.5; particles <2.5 μm) have been associated with cardiovascular health. Persons with existing cardiovascular disease have been suggested to be especially vulnerable. It is unclear, how well outdoor concentrations of PM_2.5 and its constituents measured at a central site reflect personal exposures in Southern European countries. The objective of the study was to assess the relationship between outdoor and personal concentrations of PM_2.5, absorbance and sulphur among post-myocardial infarction patients in Barcelona, Spain.Thirty-eight subjects carried personal PM_2.5 monitors for 24-h once a month (2–6 repeated measurements) between November 2003 and June 2004. PM_2.5 was measured also at a central outdoor monitoring site. Light absorbance (a proxy for elemental carbon) and sulphur content of filter samples were determined as markers of combustion originating and long-range transported PM_2.5, respectively.There were 110, 162 and 88 measurements of PM_2.5, absorbance and sulphur, respectively. Levels of outdoor PM_2.5 (median 17 μg m³) were lower than personal PM_2.5 even after excluding days with exposure to environmental tobacco smoke (ETS) (median after exclusion 27 μg m³). However, outdoor concentrations of absorbance and sulphur were similar to personal concentrations after exclusion of ETS. When repeated measurements were taken into account, there was a statistically significant association between personal and outdoor absorbance when adjusting for ETS (slope 0.66, p<0.001), but for PM_2.5 the association was weaker (slope 0.51, p=0.066). Adjustment for ETS had little effect on the respective association of S (slope 0.69, p<0.001).Our results suggest that outdoor measurements of absorbance and sulphur can be used to estimate both the daily variation and levels of personal exposures also in Southern European countries, especially when exposure to ETS has been taken into account. For PM_2.5, indoor sources need to be carefully considered.