Solubility of toluene,benzene and TCE in high-microbial concentration systems

We report measurements of solubility limits for benzene, toluene, and TCE in systems that contain varying levels of biomass up to 0.13 g mL⁻¹ for TCE and 0.25 g mL⁻¹ for benzene and toluene. The solubility limit increased from 21 to 48 mM when biomass (in the form of yeast) was added to aqueous batch systems containing benzene. The toluene solubility limit increased from 4.9 to greater than 20 mM. For TCE, the solubility increased from 8 mM to more than 1000 mM. Solubility for TCE (trichloroethylene) was most heavily impacted by biomass levels, changing by two orders of magnitude as the microbial concentrations approach those in biofilms.     

Assessment and prediction of exposure to benzene of filling station employees

In the present study, the exposure to benzene of employees working in two filling stations (one urban and one rural) was estimated, through the method of passive sampling. Additional data (30′ measurements of benzene exposure through active sampling to employees dealing with different activities, meteorological and traffic data) were collected. The measurements campaign was performed in both summer and wintertime to determine the seasonal variation of the exposure pattern.In addition, a set of artificial neural networks (ANNs) was developed to predict benzene exposure pattern for the filling station employees based on active sampling data and the parameters related to the employees’ exposure. The quantification of the contribution of each parameter to the overall exposure pattern was also attempted.The results showed that although vapour recovery technologies are installed in the refuelling systems and benzene emissions are significantly reduced compared to the past, filling station employees are still highly exposed to benzene (52–15 μg m⁻³). Benzene exposure is strongly correlated to car refuelling (exposure levels up to 85 μg m⁻³), while activities like car washing or working in cash machine inside an office contribute to lower exposure levels (up to 44 and 24 μg m⁻³ respectively). In rural filling station, exposure levels were in general lower compared to the urban ones, due to the smaller amount of gasoline that was traded and the absence of any significant traffic effect or urban background concentration. The developed ANN seemed to be a promising technique in the prediction of the exposure pattern giving very good results, and the quantification of the parameters affirmed the importance of the refueling procedure to the exposure levels.     

A global assessment of chromium pollution using sperm whales (Physeter macrocephalus) as an indicator species

Chromium (Cr) is a well-known human carcinogen and a potential reproductive toxicant, but its contribution to ocean pollution is poorly understood. The aim of this study was to provide a global baseline for Cr as a marine pollutant using the sperm whale (Physeter macrocephalus) as an indicator species. Biopsies were collected from free-ranging whales around the globe during the voyage of the research vessel The Odyssey. Total Cr levels were measured in 361 sperm whales collected from 16 regions around the globe detectable levels ranged from 0.9 to 122.6 μg Cr g tissue⁻¹ with a global mean of 8.8 ± 0.9 μg g⁻¹. Two whales had undetectable levels. The highest levels were found in sperm whales sampled in the waters near the Islands of Kiribati in the Pacific (mean = 44.3 ± 14.4) and the Seychelles in the Indian Ocean (mean = 19.5 ± 5.4 μg g⁻¹). The lowest mean levels were found in whales near the Canary Islands (mean = 3.7 ± 0.8 μg g⁻¹) and off of the coast of Sri Lanka (mean = 3.3 ± 0.4 μg g⁻¹). The global mean Cr level in whale skin was 28-times higher than mean Cr skin levels in humans without occupational exposure. The whale levels were more similar to levels only observed previously in human lung tissue from workers who died of Cr-induced lung cancer. We conclude that Cr pollution in the marine environment is significant and that further study is urgently needed.     

Mercury deposition/accumulation rates in the vicinity of a lead smelter as recorded by a peat deposit

Mercury (Hg) concentration profiles and historical accumulation rates were determined in three ²¹⁰Pb-dated cores from a peat deposit in the vicinity of a lead (Pb) smelter at Příbram, Czech Republic. The Hg concentrations in peat samples ranged from 66 to 701 μg kg⁻¹. Cumulative Hg inventories from each core (for the past 150 yr) varied by a factor of 1.4 (13.6–18.5 mg Hg m⁻²), indicating variations of net Hg accumulation rate within the peat deposit. Historical changes in vegetation cover (leading to variable interception by trees) are probably responsible for this variation in space and time. The uncorrected Hg accumulation rates peaked between the 1960s and 1980s (up to 226 μg m⁻² yr⁻¹). Recent findings show that Hg records from peat tend to overestimate historical levels of Hg deposition. Therefore we used the mass loss compensation factor (MLCF) to normalize Hg accumulation rates. These corrected Hg accumulation rates were significantly lower (maximum 129 μg m⁻² yr⁻¹) and better corresponded to changes in historical smelter emissions, which were highest in the 1960s. The agreement between the corrected Hg accumulation rates in the uppermost peat sections (2–38 μg m⁻² yr⁻¹) and biomonitoring of atmospheric deposition by mosses in several recent years (4.7–34.4 μg m⁻² yr⁻¹) shows the usefulness of MLCF application on Hg accumulation in peat archives. However, the MLCF correction was unsuitable for Pb. The recent Pb deposition rates obtained by an independent biomonitoring study using mosses (0.5–127 mg m⁻² yr⁻¹) were better correlated with net Pb accumulation rates recorded in peat (7–145 mg m⁻² yr⁻¹) than with corrected rates obtained by the MLCF approach (1–28 mg m⁻² yr⁻¹).     

Acute effects of copper and mercury on the estuarine fish Pomatoschistus microps: Linking biomarkers to behaviour

The main objective of the present study was to investigate possible links between biomarkers and swimming performance in the estuarine fish Pomatoschistus microps acutely exposed to metals (copper and mercury). In independent bioassays, P. microps juveniles were individually exposed for 96 h to sub-lethal concentrations of copper or mercury. At the end of the assays, swimming performance of fish was measured using a device specially developed for epibenthic fish (SPEDE). Furthermore, the following biomarkers were measured: lipid peroxidation (LPO) and the activity of the enzymes acetylcholinesterase (AChE), lactate dehydrogenase (LDH), glutathione S-transferases (GST), 7-ethoxyresorufin-O-deethylase (EROD), superoxide dismutase (SOD), catalase (CAT), glutathione reductase (GR) and glutathione peroxidase (GPx). LC₅₀s of copper and mercury (dissolved throughout metal concentrations) at 96 h were 568 μg L⁻¹ and 62 μg L⁻¹, respectively. Significant and concentration-dependent effects of both metals on swimming resistance and covered distance against water flow were found at concentrations equal or higher than 50 μg L⁻¹ for copper and 3 μg L⁻¹ for mercury (dissolved throughout metal concentrations). These results indicate that SPEDE was efficacious to quantify behavioural alterations in the epibenthic fish P. microps at ecologically relevant concentrations. Significant alterations by both metals on biomarkers were found including: inhibition of AChE and EROD activities, induction of LDH, GST and anti-oxidant enzymes, and increased LPO levels, with LOEC values ranging from 25 to 200 μg L⁻¹ for copper and from 3 to 25 μg L⁻¹ for mercury (dissolved throughout metal concentrations). Furthermore, significant and positive correlations were found between some biomarkers (AChE and EROD) and behavioural parameters, while negative correlations were found for others (LPO, anti-oxidant enzymes and LDH) suggesting that disruption of cholinergic function through AChE inhibition, decreased detoxification capability due to EROD inhibition, additional energetic demands to face chemical stress, and oxidative stress and damage may contribute to decrease the swimming performance of fish. Since a reduced swimming capability of fish may reduce their ability to capture preys, avoid predators, and interfere with social and reproductive behaviour, the exposure of P. microps to copper and/or mercury concentrations similar to those tested here may decrease the fitness of wild populations of this species.     

Outlier detection in phosphorus dry deposition rates measured in South Florida

Dry atmospheric deposition contributes a significant amount of phosphorus to the Everglades of South Florida. Measurement of this deposition is problematic, because samples often are contaminated to varying degrees by bird droppings and other foreign materials. This study attempted to detect and remove the outliers in phosphorus (P) flux rates measured from dry deposition samples. Visual inspection of the samples, recorded in field notes, found that 30.1% of the samples contained animal droppings and frogs. Some of the samples with droppings and frogs (2.3%) had P values greater than 884 μg P m⁻² d⁻¹ (a value twice the standard deviation of the raw data mean), and were removed from further analysis. Outlier detection statistics based on a linear regression were then used for additional data screening. Eight stations in the network of 19 were removed because high contamination precluded the use of the regression model. Of the remaining samples, 15.7% were identified through the regression procedure as contaminated and were removed. The 11 station mean for P dry deposition was 85.8±79.0 μg P m⁻² d⁻¹, prior to the regression analysis, and 74.8±75.1 μg P m⁻² d⁻¹ after removal.     

Concentrations and elemental composition of particulate matter in the Buenos Aires underground system

Total suspended particulate (TSP) samples have been collected at six stations in the C and B lines of the Buenos Aires underground system and, almost simultaneously, at six ground level sites outside and nearby the corresponding underground stations, in the Oct 2005/Oct 2006 period. All these samples were analyzed for mass and elemental Fe, Cu, and Zn concentrations by using the Particle Induced X-ray Emission (PIXE) technique. Mostly, TSP concentrations were found to be between 152 μg m⁻³ (25% percentile) and 270 μg m⁻³ (75% percentile) in the platform of the stations, while those in outside ambient air oscillated from 55 μg m⁻³ (25% percentile) to 137 μg m⁻³ (75% percentile). Moreover, experimental results indicate that TSP levels are comparable to those measured for other underground systems worldwide. Statistical results demonstrate that subway TSP levels are about 3 times larger on average than those for urban ambient air. The TSP levels inside stations and outdoors are poorly correlated, indicating that TSP levels in the metro system are mainly influenced by internal sources.Regarding metal concentrations, the most enriched element in TSP samples was Fe, the levels of which ranged from 36 (25% percentile) to 86 μg m⁻³ (75% percentile) in Line C stations, while in Line B ones they varied between 8 μg m⁻³ (25% percentile) and 46 μg m⁻³ (75% percentile). As a comparison, Fe concentrations in ambient air oscillated between 0.7 μg m⁻³ (25% percentile) and 1.2 μg m⁻³ (75% percentile). Other enriched elements include Cu and Zn. With regard to their sources, Fe and Cu have been related to processes taking place inside the subway system, while Zn has been associated with outdoor vehicular traffic. Additionally, concerns about possible health implications based on comparisons to various indoor air quality limits and available toxicological information are discussed.     

Aromatic hydrocarbons at urban,sub-urban,rural (8°52′N; 67°19′W) and remote sites in Venezuela

Using the novel on-line proton transfer reaction mass spectrometry (PTR-MS) technique, atmospheric concentrations of benzene, toluene, xylenes, and C₉-benzenes were measured in Caracas (urban), Altos de Pipe (sub-urban), Calabozo (rural) and Parupa (remote), during various campaigns in 1999 and 2000.Average daytime mixing ratios measured in Caracas are 1.1, 3.2, 3.7, and 2.7 nmol/mol for benzene, toluene, xylenes, and C₉-benzenes. At the sub-urban site, located only few km from Caracas, relatively low levels (∼20% of the levels measured in Caracas) of these aromatic hydrocarbons were observed.At the rural site during the dry season, higher concentrations of benzene (0.15 nmol/mol) were recorded, whereas those of toluene (0.08 nmol/mol) were lower during that time. The aromatic hydrocarbon ratios in the wet season (benzene: 0.08 nmol/mol; toluene: 0.09 nmol/mol) are consistent with an aged urban plume, whereas biomass burning emissions dominate during the dry season. From rural and urban [benzene]/[toluene] ratios a mean HO concentration of 2.6×10⁶ molecules/cm³ was estimated during the wet season. This value must be considered an overestimate because it does not account for background concentrations which are likely for benzene and toluene.At the remote “La Gran Sabana” region (Parupa) very low mixing ratios (0.031 and 0.015 nmol/mol for benzene and toluene) are showing the pristine region to be unaffected by local sources. From the [benzene]/[toluene] ratio we deduced, that “urban” air arriving from the coastline (350 km) is likely mixed with air containing some background of benzene and toluene.Urban emissions (automobiles) should be the major source of aromatic compounds, however, during the dry season biomass burning seems to make an important contribution.     

Relationship between the ATP content of subsurface material and the rate of biodegradation of alkylbenzenes and chlorobenzene

The rate of biotransformation of toluene in unconsolidated subsurface material from sites at Lula, Oklahoma, and Conroe, Texas, was compared to the ATP (adenosine triphosphate) content of these materials. The rate of toluene degradation decreased with decreasing ATP content. When ATP contents were at or less than 0.05 ng g⁻¹, biotransformation of toluene could not be detected (less than 1% of the initial concentration was degraded per week). At intermediate concentrations of ATP, 0.37 and 0.16 ngvg⁻¹, the rates of toluene degradation were 18 ± 4.5% and 25 ± 10% of the initial concentration per week. At ATP concentrations above 1 ng g⁻¹, the rates of toluene degradation exceeded 90% of the initial concentration per week. There was no simple relationship between ATP content and chlorobenzene degradation. Subsurface material that had been exposed to creosote wastes, and which degraded toluene rapidly, also degraded benzene, o-xylene, and m-xylene.     

Biosorption of nickel(II) from aqueous solution by Aspergillus niger: Response surface methodology and isotherm study

In the present study, the effects of biosorbent Aspergillus niger dosage, initial solution pH and initial Ni(II) concentration on the uptake of Ni(II) by NaOH pretreated biomass of A. niger from aqueous solution were investigated. Batch experiments were carried out in order to model and optimize the biosorption process. The influence of three parameters on the uptake of Ni(II) was described using a response surface methodology (RSM) as well as Langmuir and Freundlich isotherm models. Optimum Ni(II) uptake of 4.82 mg Ni(II) g⁻¹ biomass (70.30%) was achieved at pH 6.25, biomass dosage of 2.98 g L⁻¹ and initial Ni(II) concentration of 30.00 mg L⁻¹ Ni(II). Langmuir and Freundlich were able to describe the biosorption isotherm fairly well. However, prediction of Ni(II) biosorption using Langmuir and Freundlich isotherms was relatively poor in comparison with RSM approaches. The biosorption mechanism was also investigated by using Fourier transfer infrared (FT-IR) analysis of untreated, NaOH pretreated, and Ni(II) loaded A. niger biomass.     

Removal of antibiotics and non-steroidal anti-inflammatory drugs by extended sludge age biological process

Removal of four antibiotics (sulfamethoxazole, sulfadimethoxine, sulfamethazine and trimethoprim) and four non-steroidal anti-inflammatory drugs (acetaminophen, ibuprofen, ketoprofen and naproxen) using extended sludge age biological process was investigated. The sludge age of the biological system was greater than 200 d. Hydraulic retention time of 12 h was maintained throughout the experiment. The extended sludge age biological process is able to treat pharmaceuticals with good and steady removal efficiencies: 64–93% removal for antibiotics over 1–5 μg L⁻¹ influent concentrations and 94% to complete removal for acetaminophen and ibuprofen with a wide range of influent concentrations 1–100 μg L⁻¹. For ketoprofen and naproxen the removal efficiencies are 79–96% over a range of 1–15 μg L⁻¹ influent concentrations. The removal efficiency decreases with increasing initial concentrations for all target compounds except for ibuprofen. This indicates that the initial influent concentration is an important parameter for the studies of fate of pharmaceuticals. The amount of bio-mass and size of the reactor required to achieve good and steady removal efficiencies for known influent pharmaceutical concentrations are also suggested in this study.     

Long-term variation of PM2.5 levels and composition at rural, urban, and roadside sites in Hong Kong: Increasing impact of regional air pollution

Long-term study of air pollution plays a decisive role in formulating and refining pollution control strategies. In this study, two 12-month measurements of PM_2.5 mass and speciation were conducted in 00/01 and 04/05 to determine long-term trend and spatial variations of PM_2.5 mass and chemical composition in Hong Kong. This study covered three sites with different land-use characteristics, namely roadside, urban, and rural environments. The highest annual average PM_2.5 concentration was observed at the roadside site (58.0±2.0 μg m⁻³ (average±2σ) in 00/01 and 53.0±2.7 μg m⁻³ in 04/05), followed by the urban site (33.9±2.5 μg m⁻³ in 00/01 and 39.0±2.0 μg m⁻³ in 04/05), and the rural site (23.7±1.9 μg m⁻³ in 00/01 and 28.4±2.4 μg m⁻³ in 04/05). The lowest PM_2.5 level measured at the rural site was still higher than the United States’ annual average National Ambient Air Quality Standard of 15 μg m⁻³. As expected, seasonal variations of PM_2.5 mass concentration at the three sites were similar: higher in autumn/winter and lower in summer. Comparing PM_2.5 data in 04/05 with those collected in 00/01, a reduction in PM_2.5 mass concentration at the roadside (8.7%) but an increase at the urban (15%) and rural (20%) sites were observed. The reduction of PM_2.5 at the roadside was attributed to the decrease of carbonaceous aerosols (organic carbon and elemental carbon) (>30%), indicating the effective control of motor vehicle emissions over the period. On the other hand, the sulfate concentration at the three sites was consistent regardless of different land-use characteristics in both studies. The lack of spatial variation of sulfate concentrations in PM_2.5 implied its origin of regional contribution. Moreover, over 36% growth in sulfate concentration was found from 00/01 to 04/05, suggesting a significant increase in regional sulfate pollution over the years. More quantitative techniques such as receptor models and chemical transport models are required to assess the temporal variations of source contributions to ambient PM_2.5 mass and chemical speciation in Hong Kong.     

The use of clays to sequestrate organic pollutants. Leaching experiments

Leaching experiments are performed from clay-pollutant systems in order to evaluate the capability of clays to sequestrate organic pollutants from wastewaters. Reference kaolinite KGa-1b, montmorrillonite SWy-2 and reference soil BCR^®-700 are the sorbent materials. 2,4,6-trichloroaniline (2,4,6-TCA) and 4-chlorophenol (4-CP) are the typical pollutants, sorbed at amounts of 10.0 mg g⁻¹ and 5.8 mg g⁻¹ on SWy-2 and 7.3 mg g⁻¹ and 2.2 mg g⁻¹ on KGa-1b, respectively.The leaching agents are ultrapure water and model solutions of acid rain and surface waters that simulate meteoric leaching. 1.0 mM HNO₃, 1.0 mM H₂SO₄ solutions and a methanol/water 50/50 (v/v) mixture simulate leaching agents of industrial source.The results are compared and the preferential capability of the clays to sequestrate the more lipophilic 2,4,6-TCA is evidenced.The bond interactions are discussed and explained through preferential adsorption reactions. For montmorrillonite also a simultaneous intercalation in the phyllosilicate interlayer is proposed.     

Development of steady-state phosphate concentrations in septic system plumes

Long-term monitoring of PO₄⁻³ behaviour in a well-defined septic system plume on calcareous sand (Cambridge site) shows that, after 17 yr of system operation, a distinct PO₄⁻³ plume (PO₄⁻³−P > 1 mg L⁻¹) is present extending 20 m downgradient from the infiltration bed. The PO₄³⁻ plume migration velocity is 1 m yr⁻¹, reflecting retardation by a factor of 20 compared to the groundwater velocity. During monitoring between years 10 to 17, an expanding steady-state zone was noted below the infiltration bed where PO₄³⁻ −P levels remained consistently near 4 mg L⁻¹, a value 25% lower than the average effluent value (6.3 mg L⁻¹). The pattern of attenuation — a 25% mass loss in the 2-m-thick vadose zone, then little further attenuation along the flowpath — is suggestive of a condition of equilibrium with a controlling phosphate mineral phase. Chemical equilibrium modelling shows supersaturation with respect to hydroxylapatite and variscite. Four other field sites are identified from the literature and from our work where similar steady-state PO₄³⁻ zones are present in septic system plumes. In these, steady-state levels range from 15% to 68% of effluent values, with lower concentrations observed in the more acidic plumes, again indicative of a mineral solubility control, possibly variscite.PO₄³⁻ behaviour in these plumes suggests that, although P migration velocity is controlled by the processes of sorption, the magnitude of PO₄³⁻ that is present is governed by the constraints of phosphate mineral solubility. When septic systems on sands are located relatively close to sensitive surface water bodies and when long-term downgradient impact is the primary concern, more attention should be focused on the geochemical conditions that control PO₄³⁻ mineral solubility rather than only on the sorption characteristics of the sediment.     

Influence of cation type, ionic strength, and pH on solubilization and mobilization of residual hydrocarbon by a biosurfactant

This study investigated the effect of cation type, ionic strength, and pH on the performance of an anionic monorhamnolipid biosurfactant for solubilization and removal of residual hexadecane from sand. Three common soil cations, Na⁺, Mg²⁺, and Ca²⁺, were used in these experiments and hexadecane was chosen to represent a nonaqueous phase liquid (NAPL) less dense than water. Results showed that hexadecane solubility in rhamnolipid solution was significantly increased by the addition of Na⁺ and Mg²⁺. Addition of up to 0.2 mM Ca²⁺ also increased hexadecane solubility. For Ca²⁺ concentrations greater than 0.2 mM there was little effect on hexadecane solubility due to competing effects of calcium-induced rhamnolipid precipitation and enhanced hexadecane solubilization. Efficiency of NAPL solubilization can be expressed in terms of molar solubilization ratios (MSR). The results showed that MSR values for hexadecane in rhamnolipid solutions increased 7.5-fold in the presence of 500 mM Na⁺, and 25-fold in the presence of 1 mM Mg²⁺. The presence of cations also reduced the interfacial tension between rhamnolipid solutions and hexadecane. For example, an increase in Na⁺ from 0 to 800 mM caused a decrease in interfacial tension from 2.2 to 0.89 dyn cm⁻¹. Similarly, decreasing pH caused a reduction in interfacial tension. The lowest interfacial tension value observed in this study was 0.02 dyn cm⁻¹ at pH 6 in the presence of 320 mM Na⁺. These conditions were also found to be optimal for removal of hexadecane residual from sand columns, with 58% of residual removed within three pore volumes. The removal of residual NAPL from the packed columns was primarily by mobilization, even though solubilization was significantly increased in the presence of Na⁺.     

Arsenic concentration in porewater of an alkaline coal ash disposal site: Roles of siderite precipitation/dissolution and soil cover

The geochemical behavior of As in porewaters of an alkaline coal ash disposal site was investigated using multilevel samplers. The disposal site was in operation from 1983 until 1994 and was covered with 0.3–0.5 m thick soils in 2001 when this study was initiated. Sequential extraction analyses and batch leaching experiments were also performed using the coal ash samples collected from the disposal site. The results suggest the important roles of siderite (FeCO₃) precipitation/dissolution and soil cover, which have been ignored previously. Arsenic levels in the porewater were very low (average of 10 μg L⁻¹) when the site was covered with soil due to coprecipitation with siderite. The soil cover enabled the creation of anoxic conditions, which raised the Fe concentration by the reductive dissolution of Fe-(hydr)oxides. Because of the high alkalinity generated from the alkaline coal ash, even a small increase in the Fe concentration (0.66 mg L⁻¹ on average) could cause siderite precipitation. When the soil cover was removed, however, an oxidizing condition was created and triggered the precipitation of dissolved Fe as (hydr)oxides. As a result, the dissolution of previously precipitated As-rich siderite caused higher As concentration in the porewater (average of 345 μg L⁻¹).     

Nitric oxide and nitrous oxide emission from Hungarian forest soils; linked with atmospheric N-deposition

Studies of forest nitrogen (N) budgets generally measure inputs from the atmosphere in wet and dry deposition and outputs via hydrologic export. Although denitrification has been shown to be important in many wetland ecosystems, emission of N oxides from forest soils is an important, and often overlooked, component of an ecosystem N budget. During 1 year (2002–03), emissions of nitric oxide (NO) and nitrous oxide (N₂O) were measured from Sessile oak and Norway spruce forest soils in northeast Hungary. Accumulation in small static chambers followed by gas chromatography-mass spectrometry detection was used for the estimation of N₂O emission flux. Because there are rapid chemical reactions of NO and ozone, small dynamic chambers were used for in situ NO flux measurements. Average soil emissions of NO were 1.2 and 2.1 μg N m⁻² h⁻¹, and for N₂O were 15 and 20 μg N m⁻² h⁻¹, for spruce and oak soils, respectively. Due to the relatively high soil water content, and low C/N ratio in soil, denitrification processes dominate, resulting in an order of magnitude greater N₂O emission rate compared to NO. The previously determined N balance between the atmosphere and the forest ecosystem was re-calculated using these soil emission figures. The total (dry+wet) atmospheric N-deposition to the soil was 1.42 and 1.59 g N m⁻² yr⁻¹ for spruce and oak, respectively, while the soil emissions are 0.14 and 0.20 g N m⁻² yr⁻¹. Thus, about 10–13% of N compounds deposited to the soil, mostly as and , were transformed in the soil and emitted back to the atmosphere, mostly as greenhouse gas (N₂O).     

Particle emissions of a railway line determined by detailed single particle analysis

The goal of this study was to identify and quantify particles emitted from railway traffic. For that purpose PM10 samples were collected near a busy railway line using a wind direction and speed controlled sampling equipment consisting of five devices. Measurements taken perpendicular to the railway lines at 10, 36 and 120 m distance enable an identification and separation of particles caused by the railway traffic from background particles. Morphology and chemistry of more than 11,000 particles were analysed by computer controlled scanning electron microscopy (CCSEM). Based on chemical composition five particle classes are defined and assigned to their sources. The mass of the individual particles is determined by multiplying their volumes, calculated based on their morphology with a density assigned specifically to each particle class. The density of the particle classes is derived from their chemical composition. To estimate the PM10 contributions of the railway lines, the mass of PM10 at 120 m (background, not influenced by the railway lines) is subtracted from the mass of PM10 at 10 m. The emissions of the railway lines are dominated by ‘iron’ particles, which contribute 2.9 μg m⁻³ or 67% to the railway related PM10. In addition, ‘aluminium’ and ‘calcium’ particles contribute also to the railway related PM10 (1.0 μg m⁻³ or 23% for the ‘aluminium’ and 0.4 μg m⁻³ or 10% for the ‘calcium’ particles). These particles are assigned to abrasion of the gravel bed and re-suspension of mineral dust.Long-term gravimetric results of the contribution of iron to the mass of railway related PM10 from a study performed earlier at the same site are in good agreement with the data presented in this study.     

Impact of the Saharan dust outbreaks on the ambient levels of total suspended particles (TSP) in the marine boundary layer (MBL) of the Subtropical Eastern North Atlantic Ocean

Six years (1998–2003) of measurements of ambient air concentrations of total suspended particulate (TSP) measured at a rural background monitoring station in Tenerife (Canary Islands), the El Río station (ER, 28°08′35″N, 16°39′20″W, 500 m a.s.l.) were studied. African dust outbreaks were objectively identified using a new quantitative tool, called the African Index. This index indicates the percentage of time that an air mass remained over an African region at one of three possible height intervals of the lower troposphere. After identifying these episodes, a study of the background TSP levels at the ER station and of direct and indirect (those which cause vertical deposition of dust) African air mass intrusion impacts was performed. Taking into account both direct and indirect episodes, a total of 322 days of African dust intrusion were objectively identified (a mean of 54 episodes per year) in the period 1998–2003, some of them caused by “transition episodes” or “return African air masses”. A subjective method confirmed that 256 of these days were caused by direct impacts of African dust on the ER station. A mean TSP value of 21.6 μg m⁻³ was found at the station during this period. All the episodes occurred when the TSP concentration was >28.5 μg m⁻³. The TSP background (14 μg m⁻³) can be assumed to be representative of the MBL of the Eastern North Atlantic subtropical region. The highest number of dust gravitational settlement (or indirect) episodes occurs in summer, but the highest contribution of these episodes to the TSP levels is in March with a monthly mean TSP contribution of up to 30.5 μg m⁻³.     

Sorption and enhanced biodegradation of trace organics in a groundwater reclamation scheme— gloucester site, Ottawa, Canada

An inexpensive scheme to reclaim groundwaters contaminated by volatile organics at the Gloucester landfill site, near Ottawa, Canada, involved pumping of contaminated water into an conducted to evaluate the possible enhancement of biodegradation to improve this remedial measure.Batch experiments revealed that toluene (0.8–1.5 mg L⁻¹) was rapidly degraded aerobically while chloroform (1.2–1.0 mg L⁻¹) was recalcitrant under aerobic or anaerobic (denitrifying) conditions. Dynamic column experiments confirmed these findings. In column experiments, both chloroform and toluene were retarded relative to the pore water velocity, but to a far lesser extent than predicted by hydrophobic sorption theory. This discrepancy is attributed to the large particulate nature of the sorbent (sawdust) which prevented rapidly migrating organics from attaining an equilibrium partitioning with the bulk of this organic matter. Addition of acetate and nitrate at 20 mg L⁻¹ stimulated aerobic activity, but was inhibitory to toluene degradation. However, when nutrient addition ceased, enhanced toluene degradation was produced by the larger microbial population.In the field experiment, addition of acetate and nitrate to groundwater influent into the sawdust/sand pit may have stimulated benzene biodegradation, but had no apparent influence on volatile chlorinated hydrocarbon biodegradation. As in the column experiments, sorptive retardation was considerably less than predicted, due to a lack of equilibrium partitioning of organic solutes within the sawdust.Enhancing biodegradation in this remedial scheme was unsuccessful for a broad range of volatile organic compound types. Periodic nutrient addition to create variable environments for microbes appears to hold more promise for remediation than the continuous nutrient input scheme. This experience demonstrates the need for realistic field-scale experiments before translating laboratory studies into full-scale remedial operations.