Competitive diesel engine emissions of sulphur and nitrogen species

NO_x, nitrate and sulphate emissions from a typical European passenger car diesel engine have been measured testing eight different fuels under five steady operating conditions (reproducing modes of the European transient urban/extraurban certification cycle). It is confirmed that nitrogen species compete with sulphur compounds to be adsorbed by diesel particulate matter (DPM) before being emitted into the atmosphere. This competition is found to increase with engine load, and is explained on the basis of the different specific surface and adsorption capacity of soot particles under different operating modes. When a high specific surface is available, as occurs in low load modes, both nitrates and sulphates are adsorbed by soot particles. On the contrary when a small surface is accessible, like in high load modes, sulphates are selectively adsorbed. This is specially important since sulphates are responsible for hydrocarbon retention in DPM due to the scrubbing effect.     

Polycyclic aromatic hydrocarbon exhaust emissions from different reformulated diesel fuels and engine operating conditions

The study of light-duty diesel engine exhaust emissions is important due to their impact on atmospheric chemistry and air pollution. In this study, both the gas and the particulate phase of fuel exhaust were analyzed to investigate the effects of diesel reformulation and engine operating parameters. The research was focused on polycyclic aromatic hydrocarbon (PAH) compounds on particulate phase due to their high toxicity. These were analyzed using a gas chromatography–mass spectrometry (GC–MS) methodology.Although PAH profiles changed for diesel fuels with low-sulfur content and different percentages of aromatic hydrocarbons (5–25%), no significant differences for total PAH concentrations were detected. However, rape oil methyl ester biodiesel showed a greater number of PAH compounds, but in lower concentrations (close to 50%) than the reformulated diesel fuels. In addition, four engine operating conditions were evaluated, and the results showed that, during cold start, higher concentrations were observed for high molecular weight PAHs than during idling cycle and that the acceleration cycles provided higher concentrations than the steady-state conditions. Correlations between particulate PAHs and gas phase products were also observed.The emission of PAH compounds from the incomplete combustion of diesel fuel depended greatly on the source of the fuel and the driving patterns.     

A chassis test procedure to mimic the heavy-duty engine transient emissions certification test

In-use emissions from vehicles using heavy-duty diesel engines can be significantly higher than the levels obtained during engine certification. These higher levels may be caused by a combination of degradation of engine components, poor engine maintenance, degradation or failure of emissions after-treatment devices, and engine and emissions system tampering. A direct comparison of in-use vehicle emissions with engine certification levels, however, is not possible without removing an engine from the vehicle in order to perform engine dynamometer emissions testing. The goal of this research was to develop a chassis test procedure that mimics the engine performance, and as such the expected emissions levels, from the engine certification emissions test prescribed in the U.S. Code of Federal Regulations. Emissions measurements were taken from two engines during testing on an engine dynamometer using the transient heavy-duty Federal Test Procedure (FTP). Additionally, each engine was installed in an appropriate vehicle, and emissions measurements were taken using a chassis dynamometer while employing a vehicle driving schedule intended to match closely the instantaneous torque and speed schedule of the engine FTP. Engine and chassis testing was performed with the engines in stock (unmodified) condition as well as in several modes to simulate either tampered or poorly maintained conditions. The use of a chassis test as a predictive tool for determining whether an engine in a vehicle would pass the engine certification test has proven to be worthwhile. Analysis of the data shows that identification of chassis-mounted engines with NOx emissions above certification levels is possible by employing engine-specific correction factors. In the case of PM emissions, significant data scatter allowed only the identification of gross PM emitters. Engine tampering and poor maintenance can raise PM and NOx emissions, and these increases can be correctly identified by a chassis test. Analysis of chassis and engine CO and HC emissions did not reveal a strong enough correlation to warrant the use of the chassis test for emissions screening of these two pollutants.     

Effects of low concentration biodiesel blends application on modern passenger cars. Part 3: Impact on PAH, nitro-PAH, and oxy-PAH emissions

This study explores the impact of five different types of methyl esters on polycyclic aromatic hydrocarbon (PAH), nitrated-PAH and oxygenated PAH emissions. The measurements were conducted on a chassis dynamometer, according to the European regulation. Each of the five different biodiesels was blended with EN590 diesel at a proportion of 10-90% v/v (10% biodiesel concentration). The vehicle was a Euro 3 compliant common-rail diesel passenger car. Emission measurements were performed over the NEDC and compared with those of the real traffic-based Artemis driving cycles. The experimental results showed that the addition of biodiesel led to some important increases in low molecular-weight PAHs (phenanthrene and anthracene) and to both increases and reductions in large PAHs which are characterised by their carcinogenic and mutagenic properties. Nitro-PAHs were found to reduce with biodiesel whereas oxy-PAH emissions presented important increases with the biodiesel blends. The impact of biodiesel source material was particularly clear on the formation of PAH compounds. It was found that most PAH emissions decreased as the average load and speed of the driving cycle increased. Cold-start conditions negatively influenced the formation of most PAH compounds. A similar trend was observed with particulate alkane emissions.     

Modelling soot and SOF emissions from a diesel engine

Modelling of soot and SOF emissions from a typical European turbocharged diesel engine has been made. The model consists of a detailed kinetic mechanism with 472 reactions (120 chemical species) and data from the thermodynamic diagnostic procedure of the combustion process of the engine. The forward kinetic constants were obtained from literature and the background constants from a self-developed non-linear fitting routine based on the Marquardt algorithm. The dilution and mixing processes inside the engine are represented by a simple Wiebe function. The system of ordinary differential equations is solved with the Rosenbrock method for rigid systems and using the interpolating Lagrange polynomials to calculate the heat capacity of each species at the corresponding temperature. The kinetic model has been implemented in Digital Visual Fortran 6.0. The model has been executed for five different fuels and three mixtures of biodiesel and reference diesel operating under three diverse conditions from the European transient urban/extraurban Certification Cycle and the results of soot and SOF predicted are compared with experimental data.     

Characterization of polycyclic aromatic hydrocarbons from the diesel engine by adding light cycle oil to premium diesel fuel

Diesel fuels governed by U.S. regulations are based on the index of the total aromatic contents. Three diesel fuels, containing various fractions of light cycle oil (LCO) and various sulfur, total polyaromatic, and total aromatic contents, were used in a heavy-duty diesel engine (HDDE) under transient cycle test to assess the feasibility of using current indices in managing the emissions of polycyclic aromatic hydrocarbons (PAHs) from HDDE. The mean sulfur content in LCO is 20.8 times as much as that of premium diesel fuel (PDF). The mean total polyaromatic content in LCO is 28.7 times as much as that of PDF, and the mean total aromatic content in LCO is 2.53 times as much as that of PDF. The total polyaromatic hydrocarbon emission factors in the exhaust from the diesel engine, as determined using PDF L3.5 (3.5% LCO and 96.5% PDF), L7.5 (7.5% LCO and 92.5% PDF), and L15 (15% LCO and 85% PDF) were 14.3, 25.8, 44, and 101 mg L(-1), respectively. The total benzo(a)pyrene equivalent (BaPeq) emission factors in the exhaust from PDF, L3.5, L7.5, and L15 were 0.0402, 0.121, 0.219, and 0.548 mg L(-1), respectively. Results indicated that using L3.5 instead of PDF will result in an 80.4% and a 201% increase of emission for total PAHs and total BaPeq, respectively. The relationships between the total polyaromatic hydrocarbon emission factor and the two emission control indices, including fuel polyaromatic content and fuel aromatic content, suggest that both indices could be used feasibly to regulate total PAH emissions. These results strongly suggest that LCO used in the traveling diesel vehicles significantly influences PAH emissions.     

Factors affecting heavy-duty diesel vehicle emissions

Societal and governmental pressures to reduce diesel exhaust emissions are reflected in the existing and projected future heavy-duty certification standards of these emissions. Various factors affect the amount of emissions produced by a heterogeneous charge diesel engine in any given situation, but these are poorly quantified in the existing literature. The parameters that most heavily affect the emissions from compression ignition engine-powered vehicles include vehicle class and weight, driving cycle, vehicle vocation, fuel type, engine exhaust aftertreatment, vehicle age, and the terrain traveled. In addition, engine control effects (such as injection timing strategies) on measured emissions can be significant. Knowing the effect of each aspect of engine and vehicle operation on the emissions from diesel engines is useful in determining methods for reducing these emissions and in assessing the need for improvement in inventory models. The effects of each of these aspects have been quantified in this paper to provide an estimate of the impact each one has on the emissions of diesel engines.     

A Chassis Test Procedure to Mimic the Heavy-Duty Engine Transient Emissions Certification Test

ABSTRACT

In-use emissions from vehicles using heavy-duty diesel engines can be significantly higher than the levels obtained during engine certification. These higher levels may be caused by a combination of degradation of engine components, poor engine maintenance, degradation or failure of emissions after-treatment devices, and engine and emissions system tampering. A direct comparison of in-use vehicle emissions with engine certification levels, however, is not possible without removing an engine from the vehicle in order to perform engine dynamometer emissions testing. The goal of this research was to develop a chassis test procedure that mimics the engine performance, and as such the expected emissions levels, from the engine certification emissions test prescribed in the U.S. Code of Federal Regulations. Emissions measurements were taken from two engines during testing on an engine dynamometer using the transient heavy-duty Federal Test Procedure (FTP). Additionally, each engine was installed in an appropriate vehicle, and emissions measurements were taken using a chassis dynamometer while employing a vehicle driving schedule     

Characterization of Polycyclic Aromatic Hydrocarbons from the

Abstract

Diesel fuels governed by U.S. regulations are based on the index of the total aromatic contents. Three diesel fuels, containing various fractions of light cycle oil (LCO) and various sulfur, total polyaromatic, and total aromatic contents, were used in a heavy-duty diesel engine (HDDE) under transient cycle test to assess the feasibility of using current indices in managing the emissions of polycyclic aromatic hydrocarbons (PAHs) from HDDE. The mean sulfur content in LCO is 20.8 times as much as that of premium diesel fuel (PDF). The mean total polyaromatic content in LCO is 28.7 times as much as that of PDF, and the mean total aromatic content in LCO is 2.53 times as much as that of PDF. The total polyaromatic hydrocarbon emission factors in the exhaust from the diesel engine, as determined using PDF L3.5 (3.5% LCO and 96.5% PDF), L7.5 (7.5% LCO and 92.5% PDF), and L15 (15% LCO and 85% PDF) were 14.3, 25.8, 44, and 101 mg L^?1, respectively. The total benzo(a)pyrene equivalent (BaP_eq) emission factors in the exhaust from PDF, L3.5, L7.5, and L15 were 0.0402, 0.121, 0.219, and 0.548 mg L^?1, respectively. Results indicated that using L3.5 instead of PDF will result in an 80.4% and a 201% increase of emission for total PAHs and total BaP_eq, respectively. The relationships between the total polyaromatic hydrocarbon emission factor and the two emission control indices, including fuel polyaromatic content and fuel aromatic content, suggest that both indices could be used feasibly to regulate total PAH emissions. These results strongly suggest that LCO used in the traveling diesel vehicles significantly influences PAH emissions.     

Tomato Root: Site of Initial Alteration in Minor Elements in Cadmium Treated Plants

Abstract

Societal and governmental pressures to reduce diesel exhaust emissions are reflected in the existing and projected future heavy-duty certification standards of these emissions. Various factors affect the amount of emissions produced by a heterogeneous charge diesel engine in any given situation, but these are poorly quantified in the existing literature. The parameters that most heavily affect the emissions from compression ignition engine-powered vehicles include vehicle class and weight, driving cycle, vehicle vocation, fuel type, engine exhaust aftertreatment, vehicle age, and the terrain traveled. In addition, engine control effects (such as injection timing strategies) on measured emissions can be significant. Knowing the effect of each aspect of engine and vehicle operation on the emissions from diesel engines is useful in determining methods for reducing these emissions and in assessing the need for improvement in inventory models. The effects of each of these aspects have been quantified in this paper to provide an estimate of the impact each one has on the emissions of diesel engines.     

Impacts of biodiesel on pollutant emissions of a JP-8-fueled turbine engine

The impacts of biodiesel on gaseous and particulate matter (PM) emissions of a JP-8-fueled T63 engine were investigated. Jet fuel was blended with the soybean oil-derived methyl ester biofuel at various concentrations and combusted in the turbine engine. The engine was operated at three power settings, namely ground idle, cruise, and takeoff power, to study the impact of the biodiesel at significantly different pressure and temperature conditions. Particulate emissions were characterized by measuring the particle number density (PND; particulate concentration), the particle size distribution, and the total particulate mass. PM samples were collected for offline analysis to obtain information about the effect of the biodiesel on the polycyclic aromatic hydrocarbon (PAH) content. In addition, temperature-programmed oxidation was performed on the collected soot samples to obtain information about the carbonaceous content (elemental or organic). Major and minor gaseous emissions were quantified using a total hydrocarbon analyzer, an oxygen analyzer, and a Fourier Transform IR analyzer. Test results showed the potential of biodiesel to reduce soot emissions in the jet-fueled turbine engine without negatively impacting the engine performance. These reductions, however, were observed only at the higher power settings with relatively high concentrations of biodiesel. Specifically, reductions of approximately 15% in the PND were observed at cruise and takeoff conditions with 20% biodiesel in the jet fuel. At the idle condition, slight increases in PND were observed; however, evidence shows this increase to be the result of condensed uncombusted biodiesel. Most of the gaseous emissions were unaffected under all of the conditions. The biodiesel was observed to have minimal effect on the formation of polycyclic aromatic hydrocarbons during this study. In addition to the combustion results, discussion of the physical and chemical characteristics of the blended fuels obtained using standard American Society for Testing and Materials (ASTM) fuel specifications methods are presented.     

Study of Miller timing on exhaust emissions of a hydrotreated vegetable oil (HVO)-fueled diesel engine

The effect of intake valve closure (IVC) timing by utilizing Miller cycle and start of injection (SOI) on particulate matter (PM), particle number, and nitrogen oxide (NO_x) emissions was studied with a hydrotreated vegetable oil (HVO)-fueled nonroad diesel engine. HVO-fueled engine emissions, including aldehyde and polyaromatic hydrocarbon (PAH) emissions, were also compared with those emitted with fossil EN590 diesel fuel. At the engine standard settings, particle number and NO_x emissions decreased at all the studied load points (50%, 75%, and 100%) when the fuel was changed from EN590 to HVO. Adjusting IVC timing enabled a substantial decrease in NO_x emission and combined with SOI timing adjustment somewhat smaller decrease in both NO_x and particle emissions at IVC??50 and??70 °CA points. The HVO fuel decreased PAH emissions mainly due to the absence of aromatics. Aldehyde emissions were lower with the HVO fuel with medium (50%) load. At higher loads (75% and 100%), aldehyde emissions were slightly higher with the HVO fuel. However, the aldehyde emission levels were quite low, so no clear conclusions on the effect of fuel can be made. Overall, the study indicates that paraffinic HVO fuels are suitable for emission reduction with valve and injection timing adjustment and thus provide possibilities for engine manufacturers to meet the strictening emission limits.

Implications: NO_x and particle emissions are dominant emissions of diesel engines and vehicles. New, biobased paraffinic fuels and modern engine technologies have been reported to lower both of these emissions. In this study, even further reductions were achieved with engine valve adjustment combined with novel hydrotreated vegetable oil (HVO) diesel fuel. This study shows that new paraffinic fuels offer further possibilities to reduce engine exhaust emissions to meet the future emission limits.

Supplementary Materials: Supplementary materials are available for this paper. Go to the publisher's online edition of the Journal of the Air & Waste Management Association for a complete list of analysed PAH compounds.     

Impacts of Biodiesel on Pollutant Emissions of a JP-8–Fueled Turbine Engine

Abstract

The impacts of biodiesel on gaseous and particulate matter (PM) emissions of a JP-8–fueled T63 engine were investigated. Jet fuel was blended with the soybean oil-derived methyl ester biofuel at various concentrations and combusted in the turbine engine. The engine was operated at three power settings, namely ground idle, cruise, and takeoff power, to study the impact of the biodiesel at significantly different pressure and temperature conditions. Particulate emissions were characterized by measuring the particle number density (PND; particulate concentration), the particle size distribution, and the total particulate mass. PM samples were collected for off-line analysis to obtain information about the effect of the biodiesel on the polycyclic aromatic hydrocarbon (PAH) content. In addition, temperature-programmed oxidation was performed on the collected soot samples to obtain information about the carbonaceous content (elemental or organic). Major and minor gaseous emissions were quantified using a total hydrocarbon analyzer, an oxygen analyzer, and a Fourier Transform IR analyzer. Test results showed the potential of biodiesel to reduce soot emissions in the jet-fueled turbine engine without negatively impacting the engine performance. These reductions, however, were observed only at the higher power settings with relatively high concentrations of biodiesel. Specifically, reductions of ～15% in the PND were observed at cruise and takeoff conditions with 20% biodiesel in the jet fuel. At the idle condition, slight increases in PND were observed; however, evidence shows this increase to be the result of condensed uncombusted biodiesel. Most of the gaseous emissions were unaffected under all of the conditions. The biodiesel was observed to have minimal effect on the formation of polycyclic aromatic hydrocarbons during this study. In addition to the combustion results, discussion of the physical and chemical characteristics of the blended fuels obtained using standard American Society for Testing and Materials (ASTM) fuel specifications methods are presented.     

Certification of a long-term sampling system for PCDFs and PCDDs in the flue gas from industrial facilities

AMESA (adsorption method for sampling of dioxins) is a fully automatic system for long term monitoring of dioxin emissions from industrial processes based on the adsorption method. The system has been tested and undergoing a certification procedure according to the German guidelines for certification of systems for continuous monitoring of special substances. The certification covered parameters such as disposability of the system, reproducibility of the results and comparability of the sampling method with German and European standard methods. Furthermore break through, blanks and sample storability were investigated. The results prove that AMESA is a state of the art sampling system for continuous monitoring of dioxin/furan emissions.     

Experimental investigation of regulated and unregulated emissions from a diesel engine fueled with Euro V diesel fuel and fumigation methanol

Experiments were conducted on a four-cylinder direct-injection diesel engine with part of the engine load taken up by fumigation methanol injected into the air intake of each cylinder to investigate the regulated and unregulated gaseous emissions and particulate emission of the engine under five engine loads at an engine speed of 1920 rev min^?1. The fumigation methanol was injected to top up 10%, 20% and 30% of the engine load under different engine operating conditions.The experimental results show that at low engine loads, the brake thermal efficiency (BTE) decreases with increase in fumigation methanol; but at high engine loads, the BTE is not significantly affected by fumigation methanol. The fumigation methanol results in significant increase in hydrocarbon (HC), carbon monoxide (CO) and nitrogen dioxide (NO₂) emissions, but decrease in nitrogen oxides (NO_x). For the unregulated gaseous emissions, unburned methanol, formaldehyde and BTX (benzene, toluene and xylene) emissions increase but ethyne, ethene and 1,3-butadiene emissions decrease. Particulate mass and number concentrations also decrease with increase in fumigation methanol. A diesel oxidation catalyst (DOC) is found to reduce significantly most of the pollutants, including the air toxics, when the exhaust gas temperature is sufficiently high.     

Field Measurements of Particulate Matter Emissions,Carbon Monoxide,and Exhaust Opacity from Heavy-Duty Diesel Vehicles

ABSTRACT

Diesel particulate matter (PM) is a significant contributor to ambient air PM₁₀ and PM_2.5 particulate levels. In addition, recent literature argues that submicron diesel PM is a pulmonary health hazard. There is difficulty in attributing PM emissions to specific operating modes of a diesel engine, although it is acknowledged that PM production rises dramatically with load and that high PM emissions occur during rapid load increases on turbocharged engines. Snap-acceleration tests generally identify PM associated with rapid transient operating conditions, but not with high load. To quantify the origin of PM during transient engine operation, continuous opacity measurements have been made using a Wager 650CP full flow exhaust opacity meter. Opacity measurements were taken while the vehicles were operated over transient driving cycles on a chassis dynamometer using the West Virginia University (WVU) Transportable Heavy Duty Vehicle Emissions Testing Laboratories. Data were gathered from Detroit Diesel, Cummins, Caterpillar, and Navistar heavy-duty (HD) diesel engines. Driving cycles used were the Central Business District (CBD) cycle, the WVU 5-Peak Truck cycle, the WVU 5-Mile route, and the New York City Bus (NYCB) cycle. Continuous opacity measurements, integrated over the entire driving cycle, were compared to total integrated PM mass. In addition, the truck was subjected to repeat snap-acceleration tests, and PM was collected for a composite of these snap-acceleration tests. Additional data were obtained from a fleet of 1996 New Flyer buses in Flint, MI, equipped with electronically controlled Detroit Diesel Series 50 engines. Again, continuous opacity, regulated gaseous emissions, and PM were measured. The relationship between continuous carbon monoxide (CO) emissions and continuous opacity was noted. In identifying the level of PM emissions in transient diesel engine operation, it is suggested that CO emissions may prove to be a useful indicator and may be used to apportion total PM on a continuous basis over a transient cycle. The projected continuous PM data will prove valuable in future mobile source inventory prediction.     

The effect of oils on PAH, PCDD, PCDF, and PCB emissions from a spark engine fueled with leaded gasoline

The effect of synthetic and mineral oils on the formation of polyaromatic hydrocarbons (PAHs), polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), and biphenyls (PCBs) in emissions from a spark ignition engine was studied on a Skoda Favorit engine fueled with leaded gasoline. The test cycle simulated urban traffic conditions on a chassis dynamometer, in accordance with the ECC 83.00 test. The data for selected PAHs as well as PCDDs, PCDFs, and PCBs congener profiles are presented. PCDD/Fs emissions for an unused oil and the oil after 10000-km operation varied from 300 to 2000 fmol/m3, PCBs emissions from 75 to 178 pmol/m3, and PAHs emissions from 150 to 420 microg/m3. The content of PCBs in oils varied from 2 to 920 mg/kg.     

Environmental pollution from the use of alternative fuels in a four-stroke engine

This paper discusses the use of the fuels propane and butane–propane (80:20) in a four-stroke engine made to function with gasoline (petrol). The experiment covered gas emissions, emissions temperature and fuel consumption. It was observed that gas emissions were reduced compared with gasoline. The reduction for carbon monoxide emissions was greater when butane–propane was used. The same was true for hydrocarbon emissions when the electrical load was below 1500 W, but above 1500 W propane performed better. Higher emissions temperatures were observed with both alternative fuels. Under unloaded conditions the emissions from propane combustion have higher temperature, whereas under full load conditions the emissions from the combustion of the butane–propane mixture have higher temperature. The consumption of propane is lower than that of the mixture.     

Heavy Duty Diesel Particulate Emission Factors

For the past several years, EPA has been measuring particulate emissions from a variety of heavy-duty diesel engines through contracts with Southwest Research Institute. Particulate emissions samples have been collected using an exhaust splitter to divert a fraction of the engine exhaust into a standard dilution tunnel. A small fraction of the diluted exhaust from the tunnel is pulled through a filter from which particulate mass and, in some cases, organic content of the particulate is determined. This paper discusses the sampling system and gives particulate emission factors that have been computed from truck and bus fuel consumption data as well as average truck and bus speed data from New York and Los Angeles (freeway and nonfreeway usage). Average particulate emission test results (steady state tests) for 2-stroke engines were 4.74 g/kg fuel and for 4-stroke engines were 2.64 g/kg fuel. Using average particulate emissions results, a particulate emission factor range of 0.8 to 1.3 g/km was computed. Nationwide diesel particulate emissions were calculated to be 88,000 metric tons per year.     

Effects of biodiesel on emissions of regulated air pollutants and polycyclic aromatic hydrocarbons under engine durability testing

An 80,000-km durability test was performed on two engines using diesel and biodiesel (methyl ester of waste cooking oil) as fuel in order to examine emissions resulting from the use of biodiesel. The test biodiesel (B20) was blended with 80% diesel and 20% methyl ester derived from waste cooking oil. Emissions of regulated air pollutants, including CO, HC, NO_x, particulate matter (PM) and polycyclic aromatic hydrocarbons (PAHs) were measured at 20,000-km intervals. The identical-model engines were installed on a standard dynamometer equipped with a dilution tunnel used to measure the pollutants. To simulate real-world driving conditions, emission measurements were made in accordance with the United States Environmental Protection Agency (USEPA) FTP transient cycle guidelines. At 0 km of the durability test, HC, CO and PM emission levels were lower for the B20 engine than those for diesel. After running for 20,000 km and longer, they were higher. However, the deterioration coefficients for these regulated air pollutants were not statistically higher than 1.0, implying that the emission factors do not increase significantly after 80,000 km of driving. Total (gaseous+particulate phase) PAH emission levels for both B20 and diesel decreased as the driving mileage accumulated. However, for the engine using B20 fuel, particulate PAH emissions increased as engine mileage increased. The average total PAH emission factors were 1097 and 1437 μg bhp h⁻¹ for B20 and diesel, respectively. For B20, the benzo[a]pyrene equivalence emission factors were 0.77, 0.24, 0.20, 7.48, 5.43 and 14.1 μg bhp h⁻¹ for 2-, 3-, 4-, 5-, 6-ringed and total PAHs. Results show that B20 use can reduce both PAH emission and its corresponding carcinogenic potency.