Cosolvent flushing for the remediation of PAHs from former manufactured gas plants

Cosolvent flushing is a technique that has been proposed for the removal of hydrophobic organic contaminants in the subsurface. Cosolvents have been shown to dramatically increase the solubility of such compounds compared to the aqueous solubility; however, limited data are available on the effectiveness of cosolvents for field-contaminated media. In this work, we examine cosolvent flushing for the removal of polycyclic aromatic hydrocarbons (PAHs) in soil from a former manufactured gas plant (FMGP). Batch studies confirmed that the relationship between the soil-cosolvent partitioning coefficient (K(i)) and the volume fraction of cosolvent (f(c)) followed a standard log-linear equation. Using methanol at an fc of 0.95, column studies were conducted at varying length scales, ranging from 11.9 to 110 cm. Removal of PAH compounds was determined as a function of pore volumes (PVs) of cosolvent flushed. Despite using a high f(c), rate and chromatographic effects were observed in all the columns. PAH effluent concentrations were modeled using a common two-site sorption model. Model fits were improved by using MeOH breakthrough curves to determine fitted dispersion coefficients. Fitted mass-transfer rates were two to three orders of magnitude lower than predicted values based on published data using artificially contaminated sands.     

Polycyclic aromatic hydrocarbons in fuel-oil contaminated soils, Antarctica

Where fuel oil spills have occurred on Antarctic soils polycyclic aromatic hydrocarbons (PAH) may accumulate. Surface and subsurface soil samples were collected from fuel spill sites up to 30 years old, and from nearby control sites, and analysed for the 16 PAHs on the USEPA priority pollutants list, as well as for two methyl substituted naphthalenes, 1-methylnaphthalene and 2-methylnaphthalene. PAH levels ranged from 41-8105 ng g-1 of dried soil in the samples from contaminated sites and were below detection limits in control site samples. PAH were detected in surface soils and had migrated to lower depths in the contaminated soil. The predominant PAH detected were naphthalene and its methyl derivatives.     

Polycyclic aromatic hydrocarbon exhaust emissions from different reformulated diesel fuels and engine operating conditions

The study of light-duty diesel engine exhaust emissions is important due to their impact on atmospheric chemistry and air pollution. In this study, both the gas and the particulate phase of fuel exhaust were analyzed to investigate the effects of diesel reformulation and engine operating parameters. The research was focused on polycyclic aromatic hydrocarbon (PAH) compounds on particulate phase due to their high toxicity. These were analyzed using a gas chromatography–mass spectrometry (GC–MS) methodology.Although PAH profiles changed for diesel fuels with low-sulfur content and different percentages of aromatic hydrocarbons (5–25%), no significant differences for total PAH concentrations were detected. However, rape oil methyl ester biodiesel showed a greater number of PAH compounds, but in lower concentrations (close to 50%) than the reformulated diesel fuels. In addition, four engine operating conditions were evaluated, and the results showed that, during cold start, higher concentrations were observed for high molecular weight PAHs than during idling cycle and that the acceleration cycles provided higher concentrations than the steady-state conditions. Correlations between particulate PAHs and gas phase products were also observed.The emission of PAH compounds from the incomplete combustion of diesel fuel depended greatly on the source of the fuel and the driving patterns.     

Dissolution and removal of PAHs from a contaminated soil using sunflower oil

This study reports on the feasibility of remediation of polycyclic aromatic hydrocarbon (PAH) contaminated soils using sunflower oil, an environmentally-friendly solvent. Batch experiments were performed to test the influence of oil/soil ratio on the remediation of PAH contaminated soil, and to test the mass transfer behaviors of PAHs from soil to oil. An empirical model was employed to describe the kinetics of PAH dissolution and to predict equilibrium concentrations of PAHs in oil. PAH containing oil was regenerated using active carbon. Results show that dissolution of PAHs from a Manufactured Gas Plant (MGP) soil at oil/soil ratios of one or two were almost the same. Nearly all PAHs (81-100%) could be removed by sunflower oil dissolution. Mass transfer coefficients for low molecular PAHs namely fluoranthene, phenanthrene and anthracene were one or two orders of magnitude higher than those for high molecular PAHs with 4-6 rings. Ninety milliliters of PAH containing oil could be regenerated by 10 g active carbon in a batch reactor. Such a remediation procedure indicates that sunflower oil is a promising agent for the removal of PAHs from MGP soils. However, further research is required before the method can be used for in situ remediation of contaminated sites.     

Removal of polycyclic aromatic hydrocarbons from aged-contaminated soil using cyclodextrins: experimental study

The removal of polycyclic aromatic hydrocarbons (PAHs) from soil using water as flushing agent is relatively ineffective due to their low aqueous solubility. However, addition of cyclodextrin (CD) in washing solutions has been shown to increase the removal efficiency several times. Herein are investigated the effectiveness of cyclodextrin to remove PAH occurring in industrially aged-contaminated soil. Beta-cyclodextrin (BCD), hydroxypropyl-beta-cyclodextrin (HPCD) and methyl-beta-cyclodextrin (MCD) solutions were used for soil flushing in column test to evaluate some influent parameters that can significantly increase the removal efficiency. The process parameters chosen were CD concentration, ratio of washing solution volume to soil weight, and temperature of washing solution. These parameters were found to have a significant and almost linear effect on PAH removal from the contaminated soil, except the temperature where no significant enhancement in PAH extraction was observed for temperature range from 5 to 35 degrees C. The PAHs extraction enhancement factor compared to water was about 200.     

Effect of pH control at the anode for the electrokinetic removal of phenanthrene from kaolin soil

Polycyclic aromatic hydrocarbon (PAH)-contaminated soils exist at numerous sites, and these sites may threaten public health and the environment because many PAH compounds are toxic, mutagenic, and/or carcinogenic. PAHs are also hydrophobic and persistent, so conventional remediation methods are often costly or inefficient, especially when the contaminants are present in low permeability and/or organic soils. An innovative technique, electrokinetically enhanced in situ flushing, has the potential to increase soil-solution-contaminant interaction and PAH removal efficiency for low permeability soils; however, the electrolysis reaction at the anode may adversely affect the remediation of low acid buffering capacity soils, such as kaolin. Therefore, the objective of this study was to improve the remediation of low acid buffering soils by controlling the pH at the anode to counteract the electrolysis reaction. Six bench-scale electrokinetic experiments were conducted, where each test employed one of three different flushing solutions, deionized water, a surfactant, or a cosolvent. For each of these solutions, tests were performed with and without a 0.01 M NaOH solution at the anode to control the pH. The test using deionized water with pH control generated a higher electroosmotic flow than the equivalent test performed without pH control, but the electroosmotic flow difference between the surfactant and cosolvent tests with and without pH control was minor compared to that observed with the deionized water tests. Controlling the pH was beneficial for increasing contaminant solubilization and migration from the soil region adjacent to the anode, but the high contaminant concentrations that resulted in the middle or cathode soil regions indicates that subsequent changes in the soil and/or solution chemistry caused contaminant deposition and low overall contaminant removal efficiency.     

Oxygenated polycyclic aromatic hydrocarbons in atmospheric particulate matter: Molecular characterization and occurrence

Particulate matter (PM) has become a major research issue receiving increasing attention because of its significant negative impact on human health. There are main indicators that next to the morphological characteristics of the particle, also the chemical composition plays an important role in the adverse health effects of PM. In this context, the rather polar organic fraction of PM is expected to play a major role, and advanced analytical techniques are developed to improve the knowledge on the molecular composition of this fraction. One component class that deserves major attention consists of the oxygenated polycyclic aromatic hydrocarbons (PAHs). Those compounds are considered to be among the key compounds in PM toxicity. This paper presents a comprehensive review focusing on the analysis, fate and behavior of oxygenated PAHs in the atmosphere. The first part of the paper briefly introduces (i) the main sources and atmospheric pathways of oxygenated PAHs, (ii) available physical–chemical properties and (iii) their health effects. The second and main part of this paper gives a thorough discussion on the entire analytical sequence necessary to identify and quantify oxygenated PAHs on atmospheric PM. Special attention is given to critical parameters and innovations related to (i) sampling, (ii) sample preparation including both extraction and clean-up, and (iii) separation and detection. Third, the state-of-the-art knowledge about the atmospheric occurrence of oxygenated PAHs is discussed, including an extended overview of reported concentrations presented as a function of sampling season and geographical location. A clear seasonal effect is observed with the median of the oxygenated PAHs concentrations during winter being a factor of 3–4 higher than during summer. However, the oxygenated PAH/parent PAH ratio is about 20 times higher during summer, indicating the importance of photochemical activity in the atmosphere.     

Comparison of vehicle exhaust emissions from modified diesel fuels

Three diesel fuels, one oil sand-derived (OSD) diesel serving as base fuel, one cetane-enhanced base fuel, and one oxygenate [diethylene glycol dimethyl ether (DEDM)]-blended base fuel, were tested for their emission characterizations in vehicle exhaust on a light-duty diesel truck that reflects the engine technology of the 1994 North American standard. Both the cetane-enhanced and the oxygenate-blended fuels were able to reduce regulated [CO, particulate matter (PM), total hydrocarbon (THC)] and nonregulated [polyaromatic hydrocarbons (PAHs), carbonyls, and other volatile organic chemicals] emissions, except for nitrogen oxides (NO(x)), compared with the base fuel. Although burning a fuel that contains oxygen could conceivably yield more oxygenated compounds in emissions, the oxygenate-blended diesel fuel resulted in reduced emissions of formaldehyde along with hydrocarbons such as benzene, 1,3-butadiene, and PAHs. Reductions in nitro-PAH emissions have been observed in both the cetane-enhanced and oxygenated fuels. This further demonstrates the benefits of using a cetane enhancer and the oxygenated fuel component.     

Assessment of contaminant lability during phytoremediation of polycyclic aromatic hydrocarbon impacted soil

Polycyclic aromatic hydrocarbons (PAHs) are recalcitrant compounds, some of which are known carcinogens, often found in high residual soil concentrations at industrial sites. Recent research has confirmed that phytoremediation holds promise as a low-cost treatment method for PAH contaminated soil. In this study, the lability of soil bound PAHs in the rhizosphere was estimated using solid phase extraction resin. An extraction time of 14 days was determined to be appropriate for this study. Resin-extractable PAHs, which are assumed to be more bioavailable, decreased during plant treatments. Significant reductions in the labile concentrations of several PAH compounds occurred over 12 months of plant growth. The differences in concentration between the unplanted and the planted soil indicate that the presence of plant roots, in addition to the passage of time, contributes to reduction in the bioavailability of target PAHs.     

Uptake of polycyclic aromatic hydrocarbons (PAHs) in salt marsh plants Spartina alterniflora grown in contaminated sediments

Polycyclic aromatic hydrocarbon (PAH) concentrations were measured in Spartina alterniflora plants grown in pots of contaminated sediment, plants grown in native sediment at a marsh contaminated with up to 900 microg/g total PAHs, and from plants grown in uncontaminated control sediment. The roots and leaves of the plants were separated, cleaned, and analyzed for PAHs. PAH compounds were detected at up to 43 microg/g dry weight in the root tissue of plants grown in pots of contaminated soil. PAH compounds were detected at up to 0.2 microg/g in the leaves of plants grown in pots of contaminated soil. Concentrations less than 0.004 microg/g were detected in the leaves of plants grown at a reference site. Root concentration factor (RCF) values ranged from 0.009 to 0.97 in the potted plants, and from 0.004 to 0.31 at the contaminated marsh site. Stem concentration factor (SCF) values ranged from 0.00004 to 0.03 in the potted plants and 0.0002 to 0.04 at the contaminated marsh. No correlation was found between the RCF value and PAH compound or chemical properties such as logKOW. SCF values were higher for the lighter PAHs in the potted plants, but not in the plants collected from the contaminated marsh. PAH concentrations in the roots of the potted plants are strongly correlated with soil concentrations, but there is less correlation for the roots grown in natural sediments. Additional plants were grown directly in PAH-contaminated water and analyzed for alkylated PAH homologs. No difference was found in leaf PAH concentrations between plants grown in contaminated water and control plants.     

Removal of polycyclic aromatic hydrocarbons from manufactured gas plant-contaminated soils using sunflower oil: laboratory column experiments

Laboratory column experiments were performed to remove PAHs (polycyclic aromatic hydrocarbons) from two contaminated soils using sunflower oil. Two liters of sunflower oil was added to the top of the columns (33 cm x 21 cm) packed with 1 kg of PAH-contaminated soil. The sunflower oil was applied sequentially in two different ways, i.e. five additions of 400 ml or two additions of 1l. The influence of PAH concentration and the volume of sunflower oil on PAH removal were examined. A soil respiration experiment was carried out and organic carbon contents of the soils were measured to determine degradability of remaining sunflower oil in the soils. Results showed that the sunflower oil was effective in removing PAHs from the two soils, more PAHs were removed by adding sunflower oil in two steps than in five steps, probably because of the slower flow rate in the former method. More than 90% of total PAHs was removed from a heavily contaminated soil (with a total 13 PAH concentration of 4721 mg kg(-1)) using 4 l of sunflower oil. A similar removal efficiency was obtained for another contaminated soil (with a total 13 PAH concentration of 724 mg kg(-1)), while only 2l was needed to give a similar efficiency. Approximately 4-5% of the sunflower oil remained in the soils. Soil respiration curves showed that remaining sunflower oil was degraded by allowing air exchange and supplying with nutrients. Organic carbon content of the soil was restored to original level after 180 d incubation. These results indicated that the sunflower oil had a great capacity to remove PAHs from contaminated soils, and sunflower oil solubilization can be an alternative technique for remediation of PAH contaminated soils.     

Polyaromatic hydrocarbon exposure: an ecological impact ambiguity

Polyaromatic hydrocarbons (PAHs) represent a fraction of petroleum hydrocarbons and are currently one of the foremost sources of generating energy in today’s contemporary society. However, evidence highlighted in this review show that PAH pollution, as a result of oil spills, hazardous PAH-contaminated working environments and technologies which do not efficiently utilise fuels, as well as natural sources of emissions (e.g. forest fires) may have significant health implications for all taxa. The extent of damage to organisms from PAH exposure is dependent on numerous factors including degree and type of PAH exposure, nature of the environment contaminated (i.e. terrestrial or aquatic), the ability of an organism to relocate to pristine environments, type and sensitivity of organism to specific hydrocarbon fractions and ability of the organism to metabolise different PAH fractions. The review highlights the fact that studies on the potential damage of PAHs should be carried out using mixtures of hydrocarbons as opposed to individual hydrocarbon fractions due to the scarcity of individual fractions being a sole contaminant. Furthermore, potential damage of PAH-contaminated sites should be assessed using an entire ecological impact outlook of the affected area.     

Organic persistent toxic substances in soils, waters and sediments along an altitudinal gradient at Mt. Sagarmatha, Himalayas, Nepal

Persistent Organic Pollutants (POPs) and Polycyclic Aromatic Hydrocarbons (PAHs) are important classes of compounds of serious environmental concern. These compounds were measured in waters, sediments and soils from several high altitude sites in the Sagarmatha National Park (Nepal) and included in the Himalayan ridge.In water samples, low-level substituted PCBs and PBDEs, along with more volatile PAHs, were the most common contaminants. In sediment and soil samples, the PCB profile was mainly composed of medium-level chlorinated congeners and significantly correlated with altitude. The PAH profile for water and soil samples showed the main contribution of pyrogenic PAHs due to emissions of solid combustion, whereas the profile for sediments indicated the main contribution of pyrogenic PAHs from gasoline emissions. The PAH levels measured in Himalayan samples must be considered as low to medium contaminated, whereas the regarded Himalayan stations can be considered undisturbed remote areas concerning PCB, PBDE and OC compounds.     

Sources, fate, and toxic hazards of oxygenated polycyclic aromatic hydrocarbons (PAHs) at PAH-contaminated sites

In this paper we show that oxygenated polycyclic aromatic hydrocarbons (oxy-PAHs) are important cocontaminants that should be taken into account during risk assessment and remediation of sites with high levels of PAHs. The presented data, which have been collected both from our own research and the published literature, demonstrate that oxy-PAHs are abundant but neglected contaminants at these sites. The oxy-PAHs show relatively high persistency and because they are formed through transformation of PAHs, their concentrations in the environment may even increase as the sites are remediated by methods that promote PAH degradation. Furthermore, we show that oxy-PAHs are toxic to both humans and the environment, although the toxicity seems to be manifested through other effects than those known to be important for polycyclic aromatic compounds in general, that is, mutagenicity and carcinogenicity. Finally, we present data that support the hypothesis that oxy-PAHs are more mobile in the environment than PAHs, due to their polarity, and thus have a higher tendency to spread from contaminated sites via surface water and groundwater. We believe that oxy-PAHs should be included in monitoring programs at PAH-contaminated sites, even if a number of other toxicologically relevant compounds that may also be present, such as nitro-PAHs and azaarenes, are not monitored. This is because oxy-PAH levels are difficult to predict from the PAH levels, because their environmental behavior differs substantially from that of PAHs, and oxy-PAHs may be formed as PAHs are degraded.     

Partitioning of aromatic and oxygenated constituents into water from regular and ethanol-blended gasolines

Variability in gasoline-water partitioning of major aromatic constituents (benzene, toluene, ethylbenzene, and xylenes (BTEX)) and methyl tert-butyl ether (MTBE) were examined for regular and ethanol-blended gasolines. By use of a two-phase liquid-liquid equilibrium model, the distribution of nonpolar solutes between fuel phase and water was related to principles of equilibrium. The models derived using Raoult's law convention for activity coefficients and liquid solubility is presented. The observed inverse log-log linear dependence of K_fw values on aqueous solubility, could be well predicted by assuming gasoline to be an ideal solvent mixture. Oxygenated additives (i.e., ethanol and MTBE), in the low percent range (below 5%), were shown to have minimal or negligible cosolvent effects on hydrocarbon partitioning. In the case of high fuel-to-water ratio (e.g., 1:1) or near contaminant source zone, the cosolvent effect of oxygenated gasoline with high content of ethanol (e.g., E85) will be environmentally significant.     

Uptake of vapor and particulate polycyclic aromatic hydrocarbons by cabbage

Polycyclic aromatic hydrocarbons (PAHs) in cabbage (aerial part), air (gas and particles) and soil samples collected from two sites in Tianjin, China were measured. Although the levels of PAHs in all samples from the heavily contaminated site B were higher than those from the less contaminated site A, the PAH profiles were similar, suggesting the similarity in source type. PAH concentrations in cabbages were positively correlated to either gas or particle-bound PAHs in air. A multivariate linear regression with cabbage PAH as a function of both gas and particle-bound PAHs in air was established to quantitatively characterize the relationship between them. Inclusion of soil PAH concentrations would not improve the model, indicating that the contribution of soil PAHs to cabbage (aerial part) accumulation was insignificant.     

Enhancement of PAH biodegradation in soil by physicochemical pretreatment

The effects were studied of short-term heating of contaminated soil and its soaking in an organic solvent on the subsequent biodegradation of PAHs. In a clayey dredged sludge with a high organic-matter content (12%), heating at 120°C for one hour increased the degree of degradation after 21 days of an aged PAH contamination from 9.5 ± 0.7% to 27 ± 5%. Lower temperatures resulted in smaller increases. The observed increase in biodegradation is caused by either transfer of PAHs from sorption sites with low desorption rates to those with high ones or transformation of slow-sorption sites into fast-sorption ones. Soaking of the above sludge in a 4:1 (v/vj acetone-water mixture increased the degree of degradation from 9.5 ± 0.7% to 20.4 ± 1.4%, probably as a result of dissolution of the PAHs in the pore liquid during soaking. Thermal pretreatment of a contaminated sandy soil with a low organic-matter content showed no significant effect on the degradation of aged PAHs. Soaking of the sandy soil increased the degradation of only PAHs of high molecular weight, namely from 24 ± 5% to 48 ± 7%.     

Efficacy of in-situ for the remediation of PAH contaminated soils

Polycyclic aromatic hydrocarbons (PAHs) are of environmental concern because many PAHs are either carcinogens or potential carcinogens. Petroleum products are a major source of PAHs. The occurrence of PAH contamination is widespread and novel treatment technologies for the remediation of contaminated soils are necessary.Ozone has been found to be extremely useful for the degradation of PAHs in soils. For these compounds, the reaction with molecular ozone appears to be the more important degradation pathway. Greater than 95% removal of phenanthrene was achieved with an ozonation time of 2.3 h at an ozone flux of 250 mg h⁻¹. After 4.0 h of treatment at an ozone flux of 600 mg h⁻¹, 91 % of the pyrene was removed. We have also found that the more hydrophobic PAHs (e.g. chrysene) react more slowly than would be expected on the basis of their reactivity with ozone, suggesting that partitioning of the contaminant into soil organic matter may reduce the reactivity of the compound. Even so, after 4 h of exposure to ozone, the chrysene concentration in a contaminated Metea soil was reduced from 100 to 50 mg kg⁻¹ .Ozone has been found to be readily transported through columns packed with a number of geological materials, including Ottawa sand, Metea soil, Borden aquifer material and Wurtsmith aquifer material. All of these geological materials exerted a limited (finite) ozone demand, i.e. the rate of ozone degradation in soil columns is very slow after the ozone demand is met. Moisture content was found to increase the ozone demand, most likely owing to the dissolution of gaseous ozone into the pore water. As once the initial ozone demand is met, little degradation of ozone is observed, it should be possible to achieve ozone penetration to a considerable distance away from the injection well, suggesting that in-situ ozonation is a feasible means of treating uncontaminated unsaturated soils. This is substantiated by two field studies where in-situ ozonation was apparently successful at remediating the sites.     

Accumulation and distribution of polycyclic aromatic hydrocarbons in rice (Oryza sativa)

Various tissues of rice plants were sampled from a PAH contaminated site in Tianjin, China at different growth stages of the ripening period and analyzed for PAHs. PAHs were much higher in roots than in the exposed tissues. Grains and internodes accumulated much smaller amounts of PAHs than leaves, hulls or ear axes. No specific gradient trends along roots, stem, ear axes, and grains were observed, suggesting that systematic translocation among them is unlikely. Over the ripening period, PAH concentrations were increased in rice roots and decreased in most above-ground tissues. Significant correlations between PAH and lipid contents can only be observed during full mature stage. The spectra of individual PAH compounds in rice organs including roots were similar to those in air, rather than those in soil. There was also a significant correlation between bioconcentration factor (BCF, plant over air) and octanol/air partitioning coefficient (Koa).     

Accumulation of weathered polycyclic aromatic hydrocarbons (PAHs) by plant and earthworm species

Experiments were conducted to assess the bioavailability of polyclycic aromatic hydrocarbons (PAHs) in soil from a Manufactured Gas Plant site. Three plant species were cultivated for four consecutive growing cycles (28 days each) in soil contaminated with 36.3 microg/g total PAH. During the first growth period, Cucurbita pepo ssp. pepo (zucchini) tissues contained significantly greater quantities of PAHs than did Cucumis sativus (cucumber) and Cucurbita pepo ssp. ovifera (squash). During the first growth cycle, zucchini plants accumulated up to 5.47 times more total PAH than did the other plants, including up to three orders of magnitude greater levels of the six ring PAHs. Over growth cycles 2-4, PAH accumulation by zucchini decreased by 85%, whereas the uptake of the contaminants by cucumber and squash remained relatively constant. Over all four growth cycles, the removal of PAHs by zucchini was still twice that of the other species. Two earthworm species accumulated significantly different amounts of PAH from the soil; Eisenia foetida and Lumbricus terrestris contained 0.204 and 0.084 microg/g total PAH, respectively, but neither species accumulated measurable quantities 5 or 6 ring PAHs. Lastly, in abiotic desorption experiments with an aqueous phase of synthetically prepared organic acid solutions, the release of 3 and 4 ring PAHs from soil was unaffected by the treatments but the desorption of 5-6 ring constituents was increased by up to two orders of magnitude. The data show that not only is the accumulation of weathered PAHs species-specific but also that the bioavailability of individual PAH constituents is highly variable.