氢氧化镁处理含镍废水的研究

考察了氢氧化镁用量、搅拌时间、温度及pH对处理效果的影响，初步探讨了吸附作用机理。结果表明：氢氧化镁对镍离子具有较强的吸附性能，去除率可达99％以上。吸附等温线符合Langmuir模式，饱和吸附量17．57mg/g。含Cd^2 、Ni^2 和Pb^2 的电镀废水经氢氧化镁吸附后，出水达到国家排放标准。     

氢氧化镁对水中As（Ⅲ）的吸附作用

以氢氧化镁为吸附材料,通过单因素实验分别考察了氢氧化镁投加量、pH、温度、吸附时间对吸附效果的影响。研究了氢氧化镁对As（Ⅲ）的吸附热力学和动力学特性,并对作用机理进行了探讨。结果表明：在砷初始浓度为0.5～100 mg/L之间,温度为25℃,pH为3,氢氧化镁投加量为0.5～4 g,吸附时间为1 h的条件下,氢氧化镁...     

重金属离子在钠基膨润土中的吸附特征与机理

膨润土是一种天然粘土矿物,比表面积大、吸附能力强。通过钠基膨润土对复合重金属离子Cu2+、Zn2+和Cd2+的竞争吸附实验研究,探讨了钠基膨润土对Cu2+、Zn2+和Cd2+的吸附特征。结果表明,钠基膨润土对Cu2+、Zn2+和Cd2+的吸附随离子浓度增加而增大。吸附具有选择性,Cu2+、Zn2+和Cd2+的吸附能力大小顺序为Cu2+>Zn2+>Cd2+。并通过XRD及IR等分析探讨了钠基膨润土的吸附机理主要表现为离子交换吸附。     

煤泥对水溶液中Ca~(2+)的吸附性能研究

在静态条件下,研究了Ca2+在煤泥表面的吸附动力学.考察了不同Ca2+初始浓度的吸附实验,并对实验结果进行了动力学方程的拟合,结果表明,煤泥对Ca2+的吸附过程较好地符合准二级动力学方程.研究了初始Ca2+浓度、溶液pH值、振荡速度和煤泥质量对Ca2+吸附量的影响,实验结果表明:(1)煤泥对Ca2+吸附量随着Ca2+溶液浓度的增加而增大,Ca2+浓度大于3.828 mmol/L时,吸附鼍基本保持不变;(2)溶液pH<9时煤泥颗粒对Ca2+的吸附主要是静电吸附,pH>9时Ca2+在煤泥表面主要是沉淀吸附和一羟基吸附;(3)Ca2+在煤泥表面吸附的最佳振荡强度为150 r/min.     

木粉/壳聚糖接枝丙烯酸-丙烯酰胺吸附树脂对二元重金属离子溶液中Pb2+的吸附

采用自制木粉/壳聚糖接枝丙烯酸-丙烯酰胺吸附树脂R1、R2、R3对二元金属离子Cu2 +/pb2和Zn2+/pb2+溶液中的吸附性能进行了较系统考察.pb2+离子溶液中存在竞争离子Cu2+、Zn2+时,随竞争离子浓度增加,3种吸附树脂R1、R2、R3对pb2+的吸附量明显下降,而竞争离子吸附量显著增加.二元溶液中各金属离子浓度相同时,3种树脂对竞争离子Cu2+、Zn2+的吸附量大于对pb2+的吸附量;各溶液中分别加入NaCl及NaNO3、尿素后,对pb2+离子的吸附量下降迅速.随吸附树脂用量增加,竞争离子Cu2+、Zn2+的吸附量逐渐减小,pb2+的吸附量在吸附树脂用量0.10 g/L(Zn2 +/pb2+溶液)或0.15 g/L(Cu2+/pb2+溶液)时出现最大值.溶液pH值对树脂吸附性能有显著影响.3.0＜pH＜5.O时,3种树脂对竞争离子和pb2+的吸附量快速增大;5＜ pH ＜9时,树脂对竞争离子和pb2+的吸附量基本不变;9＜pH＜ll时,树脂对pb2+的吸附量减小,而对竞争离子的吸附量或增大或减小.     

改性多壁碳纳米管对水中Cd2+的去除

为了增加多壁碳纳米管(multiwall carbon nanotubers,MWNTs)对水中Cd2+的吸附量,使用混酸对多壁碳纳米管进行氧化处理,采用红外光谱进行结果表征,并探讨了吸附时间、pH值和MWNTs的使用量、Cd2+的浓度及干扰离子对镉离子吸附的影响。结果表明,吸附时间为1.5 h、pH为5.3、吸附效果最佳,随MWNTs量的增加Cd2+去除量增加,共存的阳离子会降低对Cd2+的吸附效果,对Cd2+的吸附符合Longmuir吸附定律。研究同时表明,pH小于2时Cd2+能容易从碳纳米管上解吸。初步探讨了Cd2+吸附机制。     

腐殖酸树脂处理含Pb2+、CU2+、Ni2+废水的研究

利用泥炭为原料制备腐殖酸树脂.在动态条件下,研究了腐殖酸树脂对重金属离子Pb2+、Cu2+和Ni2+的吸附效果及吸附条件.同时探讨了腐殖酸树脂对重金属离子Pb2+、Cu2+和Ni2+的吸附与解吸再生机理,吸附机理研究表明,腐殖酸树脂对重金属离子Pb2+、Cu2+和Ni2+的主要吸附形式为离子交换吸附和络合吸附.结果表明,在废水pH值为5.0～7.0,Pb2+、Cu2+和Ni2+浓度分别为50 mg/L,经腐殖酸树脂处理,Pb2+、Cu2+和Ni2+去除率可达98%以上,且处理后废水近中性.含Pb2+、Cu2+和Ni2+电镀废水经腐殖酸树脂处理后,废水中Pb2+、Cu2+和Ni2+含量显著低于国家排放标准.     

麻质活性炭的制备及其对Cu~(2+)的吸附研究

以废麻为原料,KOH为活化剂制备粉状活性炭,通过静态吸附实验研究了活性炭对Cu2+的吸附性能,探讨了溶液起始pH值、活性炭投加量、吸附时间、起始Cu2+质量浓度等对Cu2+吸附效果的影响。结果表明,溶液pH和活性炭投加量对吸附效果有较大影响,活性炭对Cu2+的吸附率在60 min内超过50%,初始浓度在10~50 mg/L时,活性炭对Cu2+的吸附量与起始浓度近似成正比。采用Langmuir、Freundlich吸附等温式对吸附平衡数据进行了拟合,结果表明吸附等温线符合Frenudlich模型。采用傅立叶红外光谱法(FT-IR)分析了活性炭的表面官能团,分析表明活性炭表面酸性官能团可能是吸附Cu2+的活性中心。     

三乙二醇二甲基丙烯酸酯为交联剂制备的高吸水树脂对重金属的吸附

以前期工作中合成的树脂PAANa-TE为吸附剂进行重金属吸附测试,考察吸附剂用量、丙烯酸中和度、吸附时间、溶液pH、初始浓度和吸附温度对树脂吸附重金属离子Cu2+、Pb2+、Cr3+和Co2+性能的影响,用原子吸收分光光度计测定了树脂吸附Cu2+、Pb2+、Cr3+和Co2+后的残留浓度,树脂对4种金属离子的吸附容量分别为21.59、2.39、5.66和4.98 mmol/g,吸附容量大小为Cu2+Cr3+Co2+Pb2+,吸附速率顺序为Cr3+Pb2+Cu2+Co2+。结果表明,该树脂对高浓度重金属离子有较快速,高效率的吸附,吸附过程在100 min左右吸附容量达到最大,并用不同浓度的酸对吸附重金属离子的树脂进行脱附处理,脱附量很小,据此可考虑进一步对金属离子进行回收处理。且脱附率较低,因此,可对工业化和城市化进程所产生的各种化学形态的重金属水体污染物造成的生态环境和质量问题起到重要的改善作用。     

4种脂肪多胺修饰硅胶对铅离子的吸附

为了合成高效铅离子吸附剂,了解其对铅离子的吸附规律。采用(3-氯丙基)三甲氧基硅烷(CPTS)架桥法,以硅胶(SG)为载体,乙二胺(EDA)、二乙烯三胺(DETA)、三乙烯四胺(TETA)和四乙烯五胺(TEPA)为表面修饰剂,合成了4种胺化硅胶,测定了它们的红外光谱、热重等性质以及对Cu2+、Zn2+和Pb2+的吸附能力。结果表明,4种胺化硅胶对Pb2+的吸附量均大于Cu2+和Zn2+的吸附量,其中DETA修饰硅胶对Pb2+的吸附量较高。4种胺化硅胶对Pb2+的吸附过程较好地符合拟二级动力学模型以及Langmuir和Scatchart等温吸附热力学模型,其对Pb2+吸附的速率常数、饱和吸附量以及吸附位点数由大到小的顺序一致,均为SG-DETASG-TEPASG-EDASG-TETA。4种胺化硅胶对Pb2+的吸附速率和吸附量呈现"奇数胺"增强效应,亲和常数则依次减小。阐明了脂肪多胺修饰硅胶对Pb2+的吸附规律,并进一步讨论了Scatchart和Langmuir热力学模型的统一性。     

皂化改性橘子皮生物吸附剂对重金属离子的吸附

以生物废料橘子皮(OP)为原料,经乙醇、氢氧化钠处理,得到改性橘子皮生物吸附剂SOP,将其用于对重金属离子Cu2+、Pb2+、Cd2+、Zn2+和Ni2+的吸附。研究了溶液pH、吸附时间和重金属离子初始浓度对SOP吸附性能的影响。结果表明,重金属离子在生物吸附剂上的吸附速率快,符合准二级动力学方程。SOP对重金属离子的吸附等温线符合Lang-muir模型,根据Langmuir模型计算SOP对Cu2+、Pb2+、Cd2+、Zn2+和Ni2+的饱和吸附量分别为56.82、152.4、66.27、33.90和23.02 mg/g,均高于改性前。常见阳离子的存在对重金属离子吸附的影响较小,改性后的橘子皮生物吸附剂可以再生重复使用4次以上,是性能良好的重金属离子吸附剂。     

Removal of copper from water by electrocoagulation process—effect of alternating current (AC) and direct current (DC)

Purpose and aim

In general, direct current (DC) is used in an electrocoagulation processes. In this case, an impermeable oxide layer may form on the cathode as well as corrosion formation on the anode due to oxidation. This prevents the effective current transfer between the anode and cathode, so the efficiency of electrocoagulation processes declines. These disadvantages of DC have been diminished by adopting alternating current (AC) in electrocoagulation processes. The main objective of this study is to investigate the effects of AC and DC on the removal of copper from water using magnesium alloy as anode and cathode.

Materials and methods

Magnesium alloy of size 2.0 dm² was used as anode and as cathode. To optimize the maximum removal efficiency, different parameters like effect of initial concentration, effect of temperature, pH, and effect of current density were studied. Copper adsorbed magnesium hydroxide coagulant was characterized by SEM, EDAX, XRD, and FTIR.

Results

The results showed that the optimum removal efficiency of copper is 97.8 and 97.2 % with an energy consumption of 0.634 and 0.996 kWh/m³ at a current density of 0.025 A/dm², pH of 7.0 for AC and DC, respectively. The adsorption of copper is preferably fitting the Langmuir adsorption isotherm for both AC and DC respectively. The adsorption process follows the second-order kinetics model with good correlation. Temperature studies showed that adsorption was endothermic and spontaneous in nature.

Conclusions

The magnesium hydroxide generated in the cell removes the copper present in the water, reducing the copper concentration to less than 1 mg/L, making it safe for drinking. The results of the scale-up study show that the process was technologically feasible.     

Biological phosphate uptake and release: effect of pH and magnesium ions.

Enhanced biological phosphorus removal (EBPR) is based on poly-phosphate accumulating organisms' (PAOs) unique features of "luxury" phosphate uptake during aerobic conditions and phosphate release in anaerobic conditions. It is believed that poly-phosphate accumulation is accompanied by the uptake and accumulation of potassium ions (K+) and magnesium ions (Mg2+). The release of phosphate under anaerobic conditions is also accompanied by the release of both cations. The objective of this research was to evaluate the effect of pH and Mg2+ on the biological phosphate uptake and release behavior of activated sludge mixed liquor during aeration and sedimentation. Research results indicate that Mg2+, supplied either by magnesium chloride (MgCl2) or magnesium hydroxide [Mg(OH)2], stimulated phosphate uptake during the aeration period, while pH increase, caused by the application of Mg(OH)2, enhanced phosphate release during the sedimentation period. It is also noted in our experiments with MgCl2 that Mg2+ slightly inhibited anaerobic phosphate release.     

Selective removal of Cr(VI) from aqueous solution by adsorption on mangosteen peel

Mangosteen peel, rich in polyphenolic compounds, was used to prepare the adsorbent exhibiting highly selective adsorption for Cr(VI) over other metal ions such as Pb²⁺, Fe³⁺, Zn²⁺, Cd²⁺, and Cr³⁺ at the pH values of 1～4. The chemical modification method proposed by using calcium hydroxide is quite cost-effective and ecofriendly without using any toxic reagents or causing any secondary pollution. The adsorption isotherm results revealed that the adsorption of Cr(VI) on the gel fit well the Langmuir adsorption model, and the maximum adsorption capacity for Cr(VI) at pH levels 1, 2, 3, and 4 was evaluated to be 2.46, 2.44, 1.99, and 2.14 mol/kg, respectively. The adsorption mechanism for Cr(VI) on the saponified gel was verified to follow an esterifiaction reaction coupled with the reduction of Cr(VI) to Cr(III) in which H⁺ plays a role of promoter. Thus, modified mangosteen peel gel has the prominent selectivity and low cost for Cr(VI) removal.     

多孔镁铝复合氧化物对水溶液中Cr（VI）的吸附性能

摘要以镁盐、铝盐、纯碱和烧碱为原料制备了一种多孔镁铝复合氧化物（P—Mg3.1AlO4.6），其比表面积、平均孔径和总孔容分别为206．3m2／g、8．961nm和0．4208cm3／g。研究了这种多孑L材料对水溶液中cr（VI）的吸附性能，在25～45qC时，静态吸附量为82．32～141．7mg／g；当初始浓度100mg／L、流速5mL／min、床层高度10cm和pH=6时，半穿透时间、半穿透吸附量和饱和吸附量分别为406rain、49．28ing／g和51．30Ing／g；拟合参数及误差分析表明，cr（Ⅵ）在P—M敬。AIO4.6上的静态吸附过程符合Freundlich等温方程式和伪二级动力学方程，Yoon·Nelson模型能很好地预测cr（Ⅵ）在P—Mg3.1A104.6上的动态穿透曲线。     

氯化镁复配硫酸铝混凝性能及絮体特性

在研究氢氧化镁混凝特性的基础上,复配氯化镁和硫酸铝作为混凝剂,以高岭土配水水样为研究对象,运用iPDA在线监测技术对混凝过程絮体形成进行监测,探讨了单独使用氯化镁和硫酸铝以及二者复配使用的混凝效果和絮体特性,确定复配使用的各种条件。结果表明,对于浊度20 NTU,pH 11.5的高岭土配水水样,氯化镁、硫酸铝最佳投加量分别为7.2 mg/L(Mg2+计)和3 mg/L(Al3+计);硫酸铝跟氯化镁复配使用时,先投加硫酸铝,间隔30 s后投加氯化镁,混凝效果较好;在镁离子最佳投加量7.2 mg/L时,铝和镁最佳质量比在1∶3~1∶2之间;镁铝复配时其FI值明显大于单独作用时,即絮体尺寸大小:二者复配硫酸铝氯化镁,而且复配条件下Zeta电位值在零电势左右浮动,浮动范围小,更利于聚集沉淀;镁铝复配时发生了协同效应,弥补了单独使用氯化镁混凝过程的不足。     

Cadmium adsorption and desorption behaviour on goethite at low equilibrium concentrations: effects of pH and index cations

The transport and bioavailability of cadmium is governed mainly by its adsorption-desorption reactions with minerals such as goethite--a common iron oxide mineral in variable charged and highly weathered tropical soils. Soil factors such as pH, temperature, solution Cd concentration, ionic strength and ageing affect Cd adsorption on goethite. The desorption behaviour of Cd from goethite at low concentrations is not fully understood. This study investigates the adsorption-desorption of Cd at low Cd concentrations (Cd adsorbed on goethite from 20 to 300 microM Cd solutions) in Na and Ca nitrate solutions of 0.03 M nominal ionic strengths. Synthetic goethite prepared by ageing a ferric hydroxide gel at high pH and room temperature was used for Cd adsorption and desorption studies. For desorption experiment 10 successive desorptions were made for the whole range of initial Cd concentrations (20-300 microM) in the presence of 0.01 M Ca(NO3)2 or 0.03 M NaNO3 solutions. Cadmium adsorption was found to be higher in Na+ than Ca2+ probably due to the competition of Ca2+ ions with Cd2+ ions for adsorption sites on the surfaces of goethite. The effect of index cation on Cd adsorption diminished with increase in pH from 5.0 to 6.0. Cadmium desorption decreased with increase in pH from 5.0 to 6.0 in both Na and Ca systems. After 10 successive desorptions with 0.03 M NaNO3 at the lowest initially adsorbed Cd approximately 45%, 20% and 7% of the adsorbed Cd was desorbed at pH 5.0, 5.5 and 6.0, respectively. The corresponding desorptions in the presence of 0.01 M Ca(NO3)2 were 49%, 22% and 8%, respectively. The Freundlich parameter, k, based on each progressive step of desorption at different adsorbed concentration increased with increasing desorption step, which may indicates that a fraction of Cd was resistant to desorption. Low Cd desorbability from goethite may be due to its specific adsorption and/or possibly as a result of Cd entrapment in the cracks or defects in goethite structure.     

用于CO2捕集的Mg（OH）2粉末溶解速率

氢氧化镁是一种正在研究的用于脱除烟气中低浓度CO2的化学吸收剂。为了掌握工业用氢氧化镁粉末的溶解速率,利用缓冲溶液,在不改变溶液体积的情况下对不同悬浊液浓度、溶液温度、溶液pH值和搅拌速率情况下的氢氧化镁粉末溶解速率进行了研究。提高悬浊液浓度、提高溶液温度、降低溶液pH值和提高搅拌速率均能增大氢氧化镁的溶解速率。悬浊液浓度从0.1 mol/L增加到1 mol/L时,溶解速率增大了2.2倍;温度从23℃增加到52℃时,溶解速率增大了4.3～9.5倍;pH值从9.8降低到6.6时,溶解速率增大了78～225倍;搅拌速率从350 r/min增加到700 r/min时,溶解速率增大了1～2倍。     

用于CO2捕集的Mg(OH)2粉末溶解速率

氢氧化镁是一种正在研究的用于脱除烟气中低浓度CO2的化学吸收剂。为了掌握工业用氢氧化镁粉末的溶解速率,利用缓冲溶液,在不改变溶液体积的情况下对不同悬浊液浓度、溶液温度、溶液pH值和搅拌速率情况下的氢氧化镁粉末溶解速率进行了研究。提高悬浊液浓度、提高溶液温度、降低溶液pH值和提高搅拌速率均能增大氢氧化镁的溶解速率。悬浊液浓度从0.1 mol/L增加到1 mol/L时,溶解速率增大了2.2倍;温度从23℃增加到52℃时,溶解速率增大了4.3～9.5倍;pH值从9.8降低到6.6时,溶解速率增大了78～225倍;搅拌速率从350 r/min增加到700 r/min时,溶解速率增大了1～2倍。     

Predictions of binary sorption isotherms for the sorption of heavy metals by pine bark using single isotherm data

The adsorption of three heavy metal ions by pine bark was studied. The study was divided into two parts; single component adsorption of the metals Cu2+, Cd2+ and Ni2+ and bisolute adsorption of the three binary systems Cu2+-Cd2+, Cu2+-Ni2+ and Cd2+-Ni2+. Extended Langmuir model, extended Freundlich model. Sips model and ideal adsorption solution theory (IAST) models were used to predict the equilibrium uptake for Cu2+, Cd2+ and Ni2+ in the binary diluted solutions using the single adsorption constants. The experimental data of single isotherm adsorption process were found to follow Langmuir isotherm model with less accuracy than Freundlich and Sips models. Whereas, the predictions of bisolute adsorption isotherms of the mentioned three systems, Cu2+-Cd2+, Cu2+-Ni2+ and Cd2+-Ni2+, showed good agreement with experimental data when using Extended-Langmuir, Extended-Freundlich and IAST. However, the only good fit of the Sips model was with the Cu2+-Cd2+ system.