Remediation of cadmium contamination in paddy soils by washing with chemicals: selection of washing chemicals

The efficiencies of neutral salts, strong acids, and chelates were tested for extracting cadmium (Cd) from three paddy soils. The higher the selectivity of the cations of the added neutral salts toward soil adsorption sites, the lower the pH in the extracts and the more soil Cd could be extracted. In addition, soil carbon and nitrogen contents and mineral composition were closely associated with the amount of Cd extracted. Calcium chloride and iron(III) chloride were selected as wash chemicals to restore Cd-contaminated paddy soils in situ. Washing with calcium chloride led to the formation of Cd chloride complexes, enhancing Cd extraction from the soils. The washing also substantially decreased soil levels of exchangeable and acid-soluble Cd, which are the major forms of bioavailable Cd for rice (Oryza sativa L.). The optimum conditions for in situ soil washing were also determined for calcium chloride.     

Influence of solution acidity and CaCl2 concentration on the removal of heavy metals from metal-contaminated rice soils

Soil washing is considered a useful technique for remediating metal-contaminated soils. This study examined the release edges of Cd, Zn, Ni, Cr, Cu or Pb in two contaminated rice soils from central Taiwan. The concentrations exceeding the trigger levels established by the regulatory agency of Taiwan were Cu, Zn, Ni and Cr for the Ho-Mei soil and Pb for the Nan-Tou soil. Successive extractions with HCl ranging from 0 to 0.2 M showed increased release of the heavy metals with declining pH, and the threshold pH value below which a sharp increase in the releases of the heavy metals was highest for Cd, Zn, and Ni (pH 4.6 to 4.9), intermediate for Pb and Cu (3.1 to 3.8) and lowest for Fe (2.1), Al (2.2) and Cr (1.7) for the soils. The low response slope of Ni and Cr particularly for the rice soils make soil washing with the acid up to the highest concentration used ineffective to reduce their concentrations to below trigger levels. Although soil washing with 0.1 M HCl was moderately effective in reducing Cu, Pb, Zn and Cd, which brought pH of the soils to 1.1+/-0.1 (S.D.), the concurrent release of large quantities of Fe and Al make this remediation technique undesirable for the rice soils containing high clay. Successive washings with 0.01 M HCl could be considered an alternative as the dissolution of Fe and Al was minimal, and between 46 to 64% of Cd, Zn, and Cu for the Ho-Mei soil and 45% of Pb in the Na-Tou soil were extracted after four successive extractions with this dilute acid solution. The efficacy of Cd extraction improved if CaCl2 was added to the acid solution. The correlation analysis revealed that Cr extracted was highly correlated (P < 0.001) with Fe extracted, whereas the Cu, Ni, Zn, Cd or Pb extracted was better correlated (P < 0.001) with Al than with Fe extracted. It is possible that the past seasonal soil flooding and drainage in the soils for rice production was conducive to incorporating Cr within the structure of Fe oxide, thereby making them extremely insoluble even in 0.2 M HCl solution. The formation of solid solution of Ni with Al oxide was also possible, making it far less extractable than Cd, Zn, Cu, or Pb with the acid concentrations used.     

Sequential soil washing techniques using hydrochloric acid and sodium hydroxide for remediating arsenic-contaminated soils in abandoned iron-ore mines

Sequential washing techniques using single or dual agents [sodium hydroxide (NaOH) and hydrochloric acid (HCl) solutions] were applied to arsenic-contaminated soils in an abandoned iron-ore mine area. We investigated the best remediation strategies to maximize arsenic removal efficiency for both soils and arsenic-containing washing solution through conducting a series of batch experiments. Based on the results of a sequential extraction procedure, most arsenic prevails in Fe-As precipitates or coprecipitates, and iron exists mostly in the crystalline forms of iron oxide. Soil washing by use of a single agent was not effective in remediating arsenic-contaminated soils because arsenic extractions determined by the Korean standard test (KST) methods for washed soils were not lower than 6mg kg(-1) in all experimental conditions. The results of X-ray diffraction (XRD) indicated that iron-ore fines produced mobile colloids through coagulation and flocculation in water contacting the soils, containing dissolved arsenic and fine particles of ferric arsenate-coprecipitated silicate. The first washing step using 0.2M HCl was mostly effective in increasing the cationic hydrolysis of amorphous ferrihydrite, inducing high removal of arsenic. Thus, the removal step of arsenic-containing flocs can lower arsenic extractions (KST methods) of washed soils. Among several washing trials, alternative sequential washing using 0.2M HCl followed by 1M HCl (second step) and 1M NaOH solution (third step) showed reliable and lower values of arsenic extractions (KST methods) of washed soils. This washing method can satisfy the arsenic regulation of washed soil for reuse or safe disposal application. The kinetic data of washing tests revealed that dissolved arsenic was easily readsorbed into remaining soils at a low pH. This result might have occurred due to dominant species of positively charged crystalline iron oxides characterized through the sequential extraction procedure. However, alkaline extraction using NaOH was effective in removing arsenic readsorbed onto the surface of crystalline minerals. This is because of the ligand displacement reaction of hydroxyl ions with arsenic species and high pH conditions that can prevent readsorption of arsenic.     

Remediation of arsenic-contaminated soils and washing effluents

Laboratory experiments were conducted to determine the distribution of various arsenic species in tailings and soils. Other specific goal of the tests were to evaluate the extraction efficiency of arsenic using alkaline or acid washing, to determine optimum operational parameters of alkaline washing, and to evaluate the arsenic precipitation of washing effluents by pH adjustment or ferric chloride addition. Alkaline washing using sodium hydroxide was found to be favorable in removing arsenic from tailings or soils having a higher portion of arsenic in the operationally defined crystalline mineral fraction of crystalline oxide and amorphous aluminosilicates. This is due to the ligand displacement reaction of hydroxyl ions with arsenic species and high pH conditions that can prevent readsorption of arsenic because predominant negatively charged crystalline oxides do not attract the negatively charged oxyanions. For tailings, sodium hydroxide had 10-20 times higher extraction efficiencies than hydrochloric- or citric acid. The optimum concentration of sodium hydroxide for soil washing was determined to be 200 mM for all samples, while the optimum ratios were 10:1 and 5:1 for tailings and field/river sedimentary soils, respectively. The washing effluent of river soil was effectively treated by adjusting pH to 5-6 with hydrochloric acid, resulting in arsenic concentrations of <50 microgl(-1). In the case of field soil effluent, an addition of ferric chloride with a minimum mass ratio of 11 (Fe/As) was needed to reduce the arsenic below 50 microgl(-1).     

Evaluation of remediation process with plant-derived biosurfactant for recovery of heavy metals from contaminated soils

A washing process was studied to evaluate the efficiency of saponin on remediating heavy metal contaminated soils. Three different types of soils (Andosol: soil A, Cambisol: soil B, Regosol: soil C) were washed with saponin in batch experiments. Utilization of saponin was effective for removal of heavy metals from soils, attaining 90-100% of Cd and 85-98% of Zn extractions. The fractionations of heavy metals removed by saponin were identified using the sequential extraction. Saponin was effective in removing the exchangeable and carbonated fractions of heavy metals from soils. In recovery procedures, the pH of soil leachates was increased to about 10.7, leading to separate heavy metals as hydroxide precipitates and saponin solute. In addition recycle of used saponin is considered to be effective for the subsequent utilization. The limits of Japanese leaching test were met for all of the soil residues after saponin treatment. As a whole, this study shows that saponin can be used as a cleaning agent for remediation of heavy metal contaminated soils.     

Short-term effects of compost amendment on the fractionation of cadmium in soil and cadmium accumulation in rice plants

Purpose

We used a sequential extraction to investigate the effects of compost amendment on Cd fractionation in soil during different incubation periods in order to assess Cd stabilization in soil over time.

Methods

Pot experiments using rice plants growing on Cd-spiked soils were carried out to evaluate the influence of compost amendment on plant growth and Cd accumulation by rice. Two agricultural soils (Pinchen and Lukang) of Taiwan were used for the experiments. The relationship between the redistribution of Cd fractions and the reduction of plant Cd concentration due to compost amendment was then investigated.

Results and discussion

Compost amendment in Pinchen soil (lower pH) could transform exchangeable Cd into the Fe- and Mn-oxide-bound forms. With increasing incubation time, exchangeable Cd tended to transform into carbonate- and Fe- and Mn-oxide-bound fractions. In Lukang soil (higher pH), carbonate- and Fe- and Mn-oxide-bonded Cd were the main fractions. Exchangeable Cd was low. Compost amendment transformed the carbonate-bound form into the Fe and Mn oxide form. Pot experiments of rice plants showed that compost amendment enhanced plant growth more in Pinchen soil than in Lukang soil. Compost amendment could significantly reduce Cd accumulation in rice roots in both Pinchen and Lukang soils and restrict internal transport of Cd from the roots to the shoots. Because exchangeable Cd can be transformed into the stronger bonded fractions quickly in Pinchen soil, a reduction of Cd accumulation in rice due to compost amendment of Pinchen soil was significant by 45?days of growth. However, carbonate-bonded fractions in Lukang soil may provide a source of available Cd to rice plants, and exchangeable and carbonate-bonded fractions are transformed into the other fractions slowly. Thus, reduction of Cd accumulation by rice due to compost amendment in Lukang soil was significant by 75?days of growth.

Conclusions

The results of the study suggest that the effectiveness of compost amendment used for stabilization of Cd and to decrease the phytoavailability of Cd for rice plants is different in acidic and alkaline soils. In acidic soil, Cd fractionation redistributes quickly after compost amendment and shows a significant reduction of Cd accumulation by the plant within a few weeks. In alkaline soil, due to the strongly bound fractions of Cd being in greater quantity than the weakly bound ones, a longer period (a few months) to redistribute Cd fractions is needed.     

Factors affecting EDTA extraction of lead from lead-contaminated soils

The effects of solution:soil ratio, major cations present in soils, and the ethylenediaminetetraacetic acid (EDTA):lead stoichiometric ratio on the extraction of lead using EDTA were studied for three different Superfund site soils, one rifle range soil, and one artificially lead-contaminated soil. Extraction of lead from the lead-contaminated soils was not affected by a solution:soil ratio as low as 3:1 but instead was dependent on the quantity of EDTA present. Results of the experiments showed that the extraction efficiencies were different for each soil. If sufficiently large amount of EDTA was applied (EDTA-Pb stoichiometric ratio greater than 10), most of the lead were extracted for all soils tested except for a Superfund site soil from a lead mining area. The differences in extraction efficiencies may be due to the major cations present in soils which may compete with lead for active sites on EDTA. For example, iron ions most probably competed strongly with lead for EDTA ligand sites for pH less than 6. In addition, copper and zinc may potentially compete with lead for EDTA ligand sites. Experimental results showed that addition of EDTA to the soil resulted in a very large increase in metals solubility. The total molar concentrations of major cations extracted were as much as 20 times the added molar concentration of EDTA. For some of the soils tested, lead may have been occluded in the iron oxides present in the soil which may affect lead extraction. While major cations present in the soil may be one of the factors affecting lead extraction efficiency, the type of lead species present also play a role.     

Heavy metal immobilization in soil near abandoned mines using eggshell waste and rapeseed residue

Heavy metal contamination of agricultural soils has received great concern due to potential risk to human health. Cadmium and Pb are largely released from abandoned or closed mines in Korea, resulting in soil contamination. The objective of this study was to evaluate the effects of eggshell waste in combination with the conventional nitrogen, phosphorous, and potassium fertilizer (also known as NPK fertilizer) or the rapeseed residue on immobilization of Cd and Pb in the rice paddy soil. Cadmium and Pb extractabilities were tested using two methods of (1) the toxicity characteristics leaching procedure (TCLP) and (2) the 0.1 M HCl extraction. With 5 % eggshell addition, the values of soil pH were increased from 6.33 and 6.51 to 8.15 and 8.04 in combination with NPK fertilizer and rapeseed residue, respectively, compared to no eggshell addition. The increase in soil pH may contribute to heavy metal immobilization by altering heavy metals into more stable in soils. Concentrations of TCLP-extracted Cd and Pb were reduced by up to 67.9 and 93.2 % by addition of 5 % eggshell compared to control. For 0.1 M HCl extraction method, the concentration of 0.1 M HCl-Cd in soils treated with NPK fertilizer and rapeseed residue was significantly reduced by up to 34.01 and 46.1 %, respectively, with 5 % eggshell addition compared to control. A decrease in acid phosphatase activity and an increase in alkaline phosphatase activity at high soil pH were also observed. Combined application of eggshell waste and rapeseed residue can be cost-effective and beneficial way to remediate the soil contaminated with heavy metals.     

Comparison of efficacy of three extractants to solubilize glomalin on hyphae and in soil

Glomalin, a glycoprotein produced by arbuscular mycorrhizal (AM) fungi, is a major component of the humus fraction of soil organic matter. Glomalin is extracted from soil and hyphae of AM fungi by using sodium citrate at 121 degrees C in multiple 1-h cycles, but extensive extraction does not solubilize all glomalin in all soils. Efficacies of 100 mM sodium salts of citrate, borate or pyrophosphate (pH 9.0, 121 degrees C) were tested for two 1-h cycles for hyphae from four AM fungal isolates and four 1-h cycles for seven soils from four US geographic regions. Residual soil glomalin was examined by pyrophosphate extraction of soils previously extracted with citrate or borate followed by extraction of all soils after treatment with NaOH. Hyphal extracts were compared using Bradford-reactive total protein (BRTP) values, and extracts from soils were compared using BRTP, percentage C and C weight. No difference among extractants was detected for AM fungal isolates or across soils. The residual glomalin across soils for extractants contained the following percentages of the total BRTP: pyrophosphate, 14%; borate, 17%; and citrate, 22%. Comparisons among individual soils indicated that pyrophosphate extracted significantly more BRTP (10-53%) than borate or citrate in six soils and borate was equal to pyrophosphate in one soil. Extraction with borate should be compared with pyrophosphate before initiating an experiment. For routine extractions of ca. 85% of the glomalin across a variety of soils, sodium pyrophosphate appears to be equal to or better than borate and better than citrate.     

Comparison of the method of diffusive gels in thin films with conventional extraction techniques for evaluating zinc accumulation in plants and isopods

The measurement of diffusive gels in thin films (DGT) has recently been developed to assess metal bioavailability in soils. The DGT-method is based on diffusion in a porous matrix. To test the predictive capabilities of the method with regard to metal bioavailability, a study was set up with 28 soils having a variety of textures and amounts of zinc salts added. Correlation and regression analyses were performed to compare DGT-extracted zinc levels to zinc concentrations obtained by extraction with 0.01 M CaCl(2) and 0.43 M HNO(3), digestion with aqua regia and the zinc concentration in pore water. The amount of zinc extracted with CaCl(2) correlated well with DGT-extracted zinc levels in all soils spiked with different amounts of ZnCl(2). A similar correlation was not found for zinc concentrations in soil samples collected in the field. Experiments were performed to compare zinc content in organisms and in soils. The organisms tested were plants (grass, lettuce and lupine) and the hard bodied soil dwelling isopod Oniscus asellus. Good correlations were found between zinc accumulation in grass and lettuce and the C(E) (effective concentration) measured by a DGT-device, CaCl(2) extracted zinc and the zinc content in the pore water of all soils. The correlation with C(E) was not significant for lupine, neither for spiked soils, nor for field soils (p< or =0.001). Zinc levels in the isopods were not significantly related to any set of zinc measurements. From a synthesis of all results obtained it is concluded that the DGT-methodology does not have an additional value in predicting bioavailability of zinc in terrestrial ecosystems as compared to conventional extraction methods.     

Extraction of arsenic in a synthetic arsenic-contaminated soil using phosphate

An environment-friendly and cost-effective extraction method has been studied for the removal of arsenic from contaminated soil. A yellow-brown forest soil was contaminated with arsenic(V) and used as a model soil. Among various potassium and sodium salts, potassium phosphate was most effective in extracting arsenic, attaining more than 40% extraction in the pH range of 6–8 with minimum damage to the soil properties. Exchange mechanism is proposed for the extraction of arsenic from soil by phosphate. Sequential extraction shows that phosphate is effective in extracting arsenic of Al- and Fe-bound forms. Arsenic of residual form was not extracted. Arsenic was efficiently extracted by phosphate solution of pH 6.0 at 300 mM phosphate concentration and at 40°C.     

Studies on the sorption and desorption characteristics of Zn(II) on the surface soils of nuclear power plant sites in India using a radiotracer technique

Zinc adsorption was studied in the soils of three nuclear power plant sites of India. 65Zn was used as a radiotracer to study the sorption characteristics of Zn(II). The sorption of zinc was determined at 25 and 45 degrees C at pH 7.8+/-0.2 in the solution of 0.01 M Ca(NO3)2 as supporting electrolyte. The sorption data was tested both in Freundlich and Langmuir isotherms and could be described satisfactorily. The effect of organic matter and other physico-chemical properties on the uptake of zinc was also studied in all the soil samples. The results showed that the cation exchange capacity, organic matter, pH and clay content were the main contributors to zinc sorption in these soils. The adsorption maximum was found to be higher in the soil on Kakarpara Atomic Power Plant sites soils having high organic matter and clay content. The zinc supply parameters of the soils are also discussed. In the desorption studies, the sequential extraction of the adsorbed zinc from soils showed that the diethylene triamine penta acetic acid extracted maximum amount of adsorbed zinc than CaCl2 and Mg(NO3)2. The zinc sorption on the soil and amount of zinc retention after extractants desorption shows a positively correlation with vermiculite and smectite mineral content present in the clay fraction of the soil. The amount desorbed by strong base (NaOH) and demineralised water was almost negligible from soils of all the sites, whereas the desorption by strong acid (HNO3) was 75-96% of the adsorbed zinc.     

Cadmium availability to wheat grain in soils treated with sewage sludge or metal salts

Grain Cd concentrations were determined in wheat (Triticum aestivum L.) grown in 1999, 2001 and 2003, at six sludge cake field experiments. Three of these sites also had comparisons with Cd availability from metal amended liquid sludge and metal salts. Grain Cd concentrations in all years and at all sites were significantly linearly correlated with NH4NO3 extractable Cd and soil total Cd (P<0.001). Soil extractability was greater in the liquid sludge and metal salt experiments than in the cake experiments, as were grain Cd concentrations. Across all the sites, NH4NO3 extractable soil Cd was no better at predicting grain Cd than soil total Cd. Stepwise multiple linear regression analysis showed that soil total Cd, pH and organic carbon were the only significant (P<0.001) variables influencing wheat grain Cd concentrations, explaining 78% of the variance across all field experiments (1408 plots). This regression predicted that the current UK soil total Cd limit of 3 mg kg(-1) was not sufficiently protective against producing grain above the European Union (EU) grain Cd Maximum Permissible Concentration (MPC) of 0.235 mg Cd kg(-1) dry weight, unless the soil pH was > 6.8. Our predictions show that grain would be below the MPC with > 95% confidence with the proposed new EU draft regulations permitting maximum total Cd concentrations in soils receiving sludge of 0.5 mg kg(-1) for soils of pH 5-6, 1 mg kg(-1) for soils of pH 6-7, and 1.5 mg kg(-1) for soils of pH > or = 7.     

An inter-laboratory study to test the ability of amendments to reduce the availability of Cd, Pb, and Zn in situ

An international inter-laboratory research program investigated the effectiveness of in situ remediation of soils contaminated by cadmium, lead and zinc, measuring changes in soil and soil solution chemistry, plants and soil microbiota. A common soil, from mine wastes in Jasper County MO, was used. The soil was pH 5.9, had low organic matter (1.2 g kg(-1) C) and total Cd, Pb, and Zn concentrations of 92, 5022, and 18 532 mg kg(-1), respectively. Amendments included lime, phosphorus (P), red mud (RM), cyclonic ashes (CA), biosolids (BIO), and water treatment residuals (WTR). Both soil solution and NH4NO3 extractable metals were decreased by all treatments. Phytotoxicity of metals was reduced, with plants grown in P treatments having the highest yields and lowest metal concentration (0.5, 7.2 and 406 mg kg(-1) Cd, Pb, and Zn). Response of soil micro-organisms was similar to plant responses. Phosphorus addition reduced the physiologically based extraction test Pb from 84% of total Pb extracted in the untreated soil to 34.1%.     

Effects of pH, Fe, and Cd on the uptake of Fe2+ and Cd2+ by rice

The rhizosphere plays an important role in altering cadmium (Cd) solubility in paddy soils and Cd accumulation in rice. However, more studies are needed to elucidate the mechanism controlling rice Cd solubility and bioavailability under different rhizosphere conditions to explain the discrepancy of previous studies. A rice culture with nutrient solution and vermiculite was conducted to assess the effects of pH, Eh, and iron (Fe) concentration on Cd, Fe fractions on the vermiculite/root surface and their uptake by rice. The solution pH was set from 4.5 to 7.5, with additions of Fe (30 and 50 mg L^?1) and Cd (0.5 and 0.9 mg L^?1). At pH 5.5, the Eh in the rice rhizosphere was higher whereas transpiration, Cd²⁺, and Fe²⁺ adsorption on the vermiculite/root surface and accumulation in rice were lower than the other pH treatments. Cadmium addition had no impact on pH and Eh in rice rhizosphere while Fe addition decreased pH and increased Eh significantly. Compared with control, Fe addition resulted in the decrease of rhizosphere Cd, Fe solubility and bioavailability. Higher redox potential in the rice rhizosphere resulted in the decline of transpiration, Cd, and Fe accumulation in the rice tissues, suggesting that the transfer of two elements from soil to rice was depressed when the rhizosphere was more oxidized.     

Remediation of DDT-Contaminated Water and Soil by Using Pretreated Iron Byproducts from the Automotive Industry

The objective of this study was to quantify the effectiveness of different pretreated iron byproducts from the automotive industry to degrade DDT [(1,1,1-trichloro-2,2-bis(4-chlorophenyl) ethane] in aqueous solutions and soil slurry. Iron byproducts from automotive manufacturing were pretreated by three different methods (heating, solvent and 0.5N HCl acid washing) prior to experimentation. All pretreated irons were used at 5% (wt v^{? 1}) to treat 0.014 mM (5 mgL^{? 1}) of DDT in aqueous solution. Among the pretreated irons, acid pretreated iron results in the fastest destruction rates, with a pseudo first-order degradation rate of 0.364 d^{? 1}. By lowering the pH of the DDT aqueous solution from 9 to 3, destruction kinetic rates increase more than 20%. In addition, when DDT-contaminated soil slurry (3.54 mg kg^{? 1}) was incubated with 5% (wt v^{? 1}) acid-pretreated iron, more than 90% destruction of DDT was observed within 8 weeks. Moreover, DDT destruction kinetics were enhanced when Fe(II), Fe(III) or Al(III) sulfate salts were added to the soil slurry, with the following order of destruction kinetics: Al(III) sulfate > Fe(III) sulfate > Fe(II) sulfate. These results provide proof-of concept that inexpensive iron byproducts of the automotive industry can be used to remediate DDT-contaminated water and soil.     

Remediation mechanisms of mercapto-grafted palygorskite for cadmium pollutant in paddy soil

The immobilization agent was the key factor that determined the success of remediation of heavy metal polluted soil. In this study, mercapto-grafted palygorskite (MP) as a novel and efficient immobilization agent was utilized for the remediation of Cd-polluted paddy soil in pot trials, and the remediation mechanisms were investigated in the aspect of soil chemistry and plant physiology with different rice cultivars as model plants. Mercapto-grafted palygorskite at applied doses of 0.1–0.3% could reduce Cd contents of brown rice and straws of different cultivars significantly. Both reduced DTPA-extractable Cd contents in rhizosphere and non-rhizosphere soil and decreasing Cd contents in iron plaques on rice root surfaces confirmed that MP was an efficient immobilization agent for Cd pollutant in paddy soil. In the aspect of soil chemistry, the pH values of rhizosphere and non-rhizosphere soils had no statistical changes in the MP treatment groups, but their zeta potentials decreased obviously, indicating that MP could enhance the fixation or sorption of Cd on soil compositions. In the aspect of antioxidant system, MP could increase POD activity of rice roots significantly to alleviate the stress of Cd to roots, and resulted in the decrease of T-AOC, SOD, and CAT activities of rice roots of the selected cultivars. MP had no inhabitation or enhancement effects on TSH of rice roots but enhance the contents of MTs and NPT to binding Cd to complete detoxification process. MP as a novel and efficient immobilization agent could complete the remediation effects through soil chemistry and plant physiological mechanisms.

     

Effects of low-molecular-weight organic acids and residence time on desorption of Cu, Cd, and Pb from soils

Effects of low-molecular-weight organic acids (LMWOAs) and residence time on desorption of Cu, Cd, and Pb from two typical Chinese soils were studied. Citric, malic, and acetic acids were chosen as representatives of LMWOAs commonly present in soils. CaCl(2) and NaNO(3) were used in desorption as they were main soil background electrolytes for comparison. Desorption of Cu, Cd, and Pb from both soils followed the descending order: citric acid>malic acid>acetic acid>CaCl(2)>NaNO(3), which was consistent with the order of stability of Cu-, Cd-, and Pb-LMWOAs complexes from large to small and ion exchange ability of Ca(2+) and Na(+). Desorption of metals by inorganic salts decreased with increasing desorption solution pH. Whereas desorption of metals by LMWOAs showed different trend in response to pH change due to their different complexing abilities. Malic and acetic acids released less metals at low pH 3.1 compared with citric acid at pH 7, indicating that pH was not the dominant factor governing the release of metals. In addition, all LMWOAs desorbed more metals than inorganic salts, CaCl(2) and NaNO(3). Therefore, organic ligands played a dominant role in desorption of heavy metals. More metals were released from Jiangxi soil than from Heilongjiang soil due to lower soil pH, CEC, organic matter content and manganese oxide of Jiangxi soil. Generally, desorption of metals decreased with increasing residence time of metals in soils.     

Remediation of cadmium-contaminated paddy soils by washing with calcium chloride: verification of on-site washing

We developed a new, three-step soil-wash method to remediate Cd-contaminated paddy fields. The method comprises (1) chemically washing the field soil with a CaCl2 solution; (2) washing the treated soil with water to eliminate residual Cd and CaCl2; and (3) on-site treatment of wastewater using a portable wastewater treatment system. Cd concentrations in the treated water were below Japan's environmental quality standard (0.01 mg Cd L-1), and the removal of Cd from the exchangeable fraction was 55% and from the acid-soluble fraction 15%. While soil fertility properties were affected by the soil washing, adverse effects were not crucial and could be corrected. The washing had no affect on rice growth, and reduced the average Cd concentration in rice grains by about two-thirds compared to a control plot. These results confirmed the effectiveness of the soil-wash method in remediating Cd-contaminated paddy fields.     

Influence of ageing on zinc bioavailability in soils

Currently, soil quality criteria or soil risk assessments of metals are based on laboratory toxicity tests which are carried out in soils freshly spiked with metal salts. With these data, species sensitivity distributions are fitted, from which hazardous concentrations and predicted no effect concentrations are derived. However, due to long-term processes, called ageing, soil metal availability decreases with time. Here we show that pH is the most important parameter determining the effect of ageing on zinc partitioning in soils, with the effect of ageing becoming more important with increasing pH. Furthermore, zinc bioavailability, expressed as the internal zinc concentrations in red clover (Trifolium pratense) is closely related to pore water zinc concentration. In addition, there is a clear dose-response relationship between the survival of the earthworm Eisenia fetida and the calcium chloride-extracted zinc fraction. These results indicate that zinc partitioning can be used to predict zinc bioavailability to terrestrial organisms. However, the use of spiked soils in toxicity assays can result in an over-estimation of the effects of zinc, especially at a high pH.