Evaluation of the thermal/optical reflectance method for discrimination between char- and soot-EC

Many optical, thermal and chemical methods exist for the measurement of elemental carbon (EC) but are unable or neglect to differentiate between the different forms of EC such as char- or soot-EC. The thermal/optical reflectance (TOR) method applies different temperatures for measuring EC and organic carbon (OC) contents through programmed, progressive heating in a controlled atmosphere, making available eight separate carbon fractions - four OC, one pyrolyzed organic carbon, and three EC. These fractions were defined by temperature protocol, oxidation atmosphere, and laser-light reflectance/transmittance. Stepwise thermal evolutional oxidation of the TOR method makes it possible to distinguish char- from soot-EC. In this study, different EC reference materials, including char and soot, were used for testing it. The thermograms of EC reference materials showed that activation energy is lower for char- than soot-EC. Low-temperature EC1 (550 degrees C in a 98% He/2% O2 atmosphere) is more abundant for char samples. Diesel and n-hexane soot samples exhibit similar EC2 (700 degrees C in a 98% He/2% O2 atmosphere) peaks, while carbon black samples peaks at both EC2 and EC3 (800 degrees C in a 98% He/2% O2 atmosphere). These results supported the use of the TOR method to discriminate between char- and soot-EC.     

Evaluation of the thermal/optical reflectance method for quantification of elemental carbon in sediments

The IMPROVE thermal/optical reflectance (TOR) method, commonly used for EC quantification in atmospheric aerosols, is applied to soils and sediments and compared with a thermochemical method commonly applied to these non-atmospheric samples. TOR determines elemental carbon (EC) by an optical method, but it also yields thermally defined EC fractions in a 2% O2/98% He oxidizing atmosphere at 550 degrees C (EC1), 700 degrees C (EC2), and 800 degrees C (EC3). Replicate TOR TC, OC, and EC values exhibited precisions of approximately +/-10% as determined from multiple analyses of the same samples. EC abundances relative to total mass concentrations were within the ranges reported by other methods for diesel exhaust soot, n-hexane soot, wood and rice chars, and coals, as well as for environmental matrices. A direct comparison with the chemothermal (CTO) method of Gustafson et al. for ten soil and sediment samples demonstrated that almost all of the OC and EC1 are eliminated, as is part of the EC2. The CTO soot carbon is bounded by the EC3 and EC2+EC3 fractions of the IMPROVE TOR analysis. It might be possible to adjust these fractions to obtain better agreement between atmospheric aerosol and soil/sediment analysis methods. Given its linking the EC measurement in the atmosphere to sediments, the TOR method will not only provide useful information on the explanation and comparison between different environmental matrices, but also can be used to derive information on global cycling of EC.     

Characterization of carbonaceous combustion residues. I. Morphological,elemental and spectroscopic features

Scanning electron microscopy, surface area determination, elemental analysis, organic matter extraction and solid-state cross polarization/magic angle spinning and Bloch decay/magic angle spinning 13C nuclear magnetic resonance (NMR) spectroscopy were used to investigate distinctive features among carbonaceous combustion residues. Black carbon (BC) samples included diesel soot, urban dust, carbon black, chimney soot, vegetation fire residues, wood and straw charcoals. Particles varied from small spheres (<50 nm) in fossil BC (>100 m(2)/g), to large layered structures in plant-derived BC (generally <8 m(2)/g). Chimney soot also included large (>1 micrometer) liquid-like structures, while spherules >100 nm were unique to urban dust. The ratios of amorphous to soot carbon (SC) (isolated by thermal degradation) were not necessarily correlated with the degree of aromaticity estimated from H/C ratios. In particular, values of SC in diesel soot were clearly overestimated. Solvent-extractable organic matter (SEOM) was <2% for charcoals and carbon black, but >13% for urban dust, chimney and diesel soot. SEOM is thought to clog pores or to form large waxy globules, hence reducing surface areas. The ratio of polar/nonpolar SEOM was generally <7 for fossil BC, but >30 for plant-derived BC. NMR analysis revealed essentially one chemical shift in the aromatic C region of charcoals, while diesel soot also showed important aliphatic contributions. Aliphatic and oxygenated C predominated over aryl C in urban dust and chimney soot. These morphological and chemical characteristics of the BC samples are discussed in terms of their environmental implications.     

Mass spectrometry up to 1 million mass units for the simultaneous detection of primary soot and of soot precursors (nanoparticles) in flames

A hybrid setup consisting of low pressure burner, flow reactor and photo-ionization mass spectrometer was used for the simultaneous detection of primary soot and of flame generated nanoparticles precursing soot. The studied flames were low pressure (120-180 mbar) C2H4/O2 flames surrounded by an N2 shield. The flow reactor was not used in this study. Through variation of the burner conditions (stoichiometry, sampling height) it could be shown that nanoparticles and soot are entirely independent species. The former, in particular, are found very early in the flame and their concentration profiles do not vary very much throughout the flame. This renders the possibility that nanoparticles are emitted together with soot and consequently may constitute an additional environmental hazard. Photo-ionization mass spectrometry is well suited for the detection of these particles.     

A comparative study of the removal of 3-indolebutyric acid using advanced oxidation processes

In this study, advanced oxidation technologies, namely Fenton Process (FP), Fenton-Like Process (FLP), ozonation (O3) and O3/H2O2 processes, were applied to synthetic wastewater containing 3-indolebutyric acid (IBA). The effectiveness of each process was investigated at different pH values, Fe(+2), Fe(+3), O3 and H2O2 concentrations with respect to the removal efficiencies for chemical oxygen demand (COD) and total organic carbon (TOC). The best removal efficiencies were seen at pH 3 and 2 mM Fe concentration in both FP and FLP, in which the optimum H2O2 concentrations were 6 mM for FP and 10 mM for FLP. Optimum process conditions were pH 12 for the O3 process, pH 9 for the O3/H2O2 process and 1:1 O3/H2O2 molar ratio. The highest COD removal efficiency was 86 percent, obtained in the O3/H2O2 process and the highest TOC removal efficiency was obtained at 77 percent in the FP.     

Effects of sample preparation on the measurement of organic carbon,hydrogen, nitrogen,sulfur, and oxygen concentrations in marine sediments

The elemental composition of marine sediment provides useful information for the study of environmental processes including biogeochemical cycling and contaminant partitioning. It is common practice to acidify marine sediment samples to remove carbonate before measuring the concentrations of organic carbon (C). To date, however the effects of acidification on the concentrations of hydrogen (H), nitrogen (N), sulfur (S) and oxygen (O) in marine sediments have not been explicitly addressed. Acidification may contaminate or alter the sediment samples and create experimental artifacts affecting the validity of resulting H/C, C/N and O/C ratios. The objective of this study was to quantify how various preparation techniques affect the measured concentrations of C, H, N, S and O in marine sediments. Effects of four different pretreatments: unacidified (whole), acidification by HCl vapor, acidification by direct addition of HCl, and combustion were evaluated using five marine sediments and a standard reference material. The magnitude of carbonate loss between the vapor and direct acidification treatments was evaluated using stable C isotope analysis. Carbonates were most effectively removed by direct addition of HCl; and our results agree with findings of other studies which found direct addition of HCl to be the most accurate method for measuring organic C. However, the acid treatments elevated the apparent concentration of H and O; and in a few cases concentrations of N and S were significantly affected by acidification. In general, combustion significantly reduced all elemental concentrations compared to the whole sample. Based on these results, we recommend analysis of the untreated whole sediment for determining N, H, O, and S.     

Photo-oxidation of cork manufacturing wastewater

Several photo-activated processes have been investigated for oxidation of a cork manufacturing wastewater. A comparative activity study is made between different homogeneous (H2O2/UV-Vis and H2O2/Fe2+/UV-Vis) and heterogeneous (TiO2/UV-Vis and TiO2/H2O2/UV-Vis) systems, with degradation performances being evaluated in terms of total organic carbon (TOC) removal. Results obtained in a batch photo-reactor show that photo-catalysis with TiO2 is not suitable for this kind of wastewater while the H2O2/UV-Vis oxidation process, for which the effect of some operating conditions was investigated, allows to remove 39% of TOC after 4 h of operation (for C(H2O2)=0.59 M, pH=10 and T=35 degrees C). The combined photo-activated process, i.e., using both TiO2 and H2O2, yields an overall TOC decrease of 46% (for C(TiO2)=1.0 gl(-1)). The photo-Fenton process proved to be the most efficient, proceeds at a much higher oxidation rate and allows to achieve 66% mineralization in just 10 min of reaction time (for C(H2O2)=0.31 M, T=30 degrees C, Fe2+:H2O2=0.12 (mol) and pH=3.2).     

Atmospheric peroxides over the North Pacific during IOC 2002 shipboard experiment

Atmospheric hydrogen peroxide and methyl hydroperoxide were determined onboard the Melville over the North Pacific from Osaka to Honolulu during May-June 2002. The concentrations of H(2)O(2) and CH(3)OOH increased from 0.64+/-0.57 ppbv and 0.27+/-0.59 ppbv in subpolar region (30-50 degrees N) to 1.96+/-0.95 ppbv and 1.56+/-1.3 ppbv in subtropical region (24-30 degrees N). The increase in concentrations towards the Equator was more pronounced for CH(3)OOH than H(2)O(2). In contrast, the levels of O(3) and CO were decreased at lower latitudes as air mass was more aged, denoted by the ratios of C(2)H(2)/CO and C(3)H(8)/C(2)H(6). CH(3)OOH concentrations showed a clear diurnal variation with a maximum around noon and minimum before sunrise. Frequently, the concentrations of peroxides remained over 1 ppbv in the dark and even gradually increased after sunset. In addition, the ratios of C(2)H(4)/C(2)H(6) and C(3)H(6)/C(3)H(8) were increased in aged subtropical air, which implies that these alkenes were emitted from the ocean surface. As a result, the reaction of these biogenic alkenes with O(3) was suggested to be a potential source for peroxides in aged marine air at lower latitudes.     

Characterization of carbonaceous combustion residues: II. Nonpolar organic compounds

Aromatic and aliphatic fractions of black carbon (BC) solvent extracts were examined by gas chromatography/mass spectrometry to determine how differences in broad chemical and physical features are correlated with the load, composition, "extractability" and bioavailability of organic compounds. Diesel soot, urban dust and chimney soot had concentrations of n-alkanes >20 microg/g and of carcinogenic polycyclic aromatic hydrocarbons (PAHs)>8 microg/g. These high levels of solvent-extractable compounds were interpreted as resulting from combustion at temperatures below optimum values for BC formation. PAH concentrations normalized to the amount of soot carbon in chimney soot were close to values for diesel soot. However, the high proportion of polar amorphous organic matter in chimney soot suggests a higher bioavailability for associated PAHs. Carbon black, vegetation fire residues, and straw and wood charcoals had only residual concentrations of n-alkanes (<9 microg/g) and PAHs (<0.2 microg/g). PAH distributions were mostly unspecific, while the overall signature of the aliphatic fraction varied with BC origin. Molecular markers among plant-derived BC included steroid and sesquiterpenoid hydrocarbons. Molecular fingerprints suggest that compounds associated with fossil BC might be more refractory than those associated with plant-derived BC.     

Using Radiocarbon to Apportion Sources of Polycyclic Aromatic Hydrocarbons in Household Soot

To determine whether polycyclic aromatic hydrocarbons (PAHs) in household soot were derived from the combustion of scrap wood or creosote that was impregnated in the wood (or some combination of both), the molecular composition and radiocarbon ( 14 C) content of the total carbon and several PAHs in the soot was investigated. The 5730-year half-life of 14 C makes it an ideal marker for identifying creosote-derived PAHs ( 14 C-free) versus those derived from the combustion of wood (contemporary 14 C). The 14 C abundance of phenanthrene, fluoranthene, pyrene, and retene was determined by accelerator mass spectrometry after solvent extraction and purification by preparative capillary gas chromatography. The molecular analysis (presence of retene and 1,7-dimethylphenanthrene) and bulk 14 C content (contemporary) of the soot indicated that wood combustion was a strong source of carbon to the soot. The 14 C of retene in two soot samples was also contemporary, indicating that it was derived from the combustion of the scrap wood. These results are consistent with previous work that has suggested that retene is an excellent marker of wood combustion. However, the 14 C content of phenanthrene, fluoranthene, and pyrene in one soot sample was much lower and revealed that these compounds had a mixed creosote and wood source. Using an isotopic mass balance approach, we estimate that 40 to 70% of phenanthrene, fluoranthene, and pyrene were derived from the combustion of the scrap wood. The results of this study show that molecular marker and bulk 14 C analysis can be potentially misleading in apportioning sources of every PAH, and that molecular-level 14 C analysis of PAHs can be a powerful tool for environmental forensics.     

Pore structure of soot deposits from several combustion sources

Soot was harvested from five combustion sources: a dodecane flame, marine and bus diesel engines, a wood stove, and an oil furnace. The soots ranged from 20% to 90% carbon by weight and molar C/H ratios from 1 to 7, the latter suggesting a highly condensed aromatic structure. Total surface areas (by nitrogen adsorption using the Brunauer Emmett Teller, BET method) ranged from 1 to 85 m2 g(-1). Comparison of the surface area and meso-pore (pores 2-50 nm) surface area predicted by density functional theory (DFT) suggested that the soot was highly porous. Total meso-pore volume and surface area ranged from 0.004-0.08 cm3 g(-1) and from 0.33-6.9 m2 g(-1) respectively, accounting for up 33% of the BET surface area. The micro-pore volume (pores <2 nm) calculated from CO2 adsorption data (by DFT) ranged from 0.0009 to 0.013 cm3 g(-1) and micro-pore surface area was 3.1-41 m2 g(-1), accounting for 10-20% of the total intra-particle (meso-plus micro-pores) pore volume and 70-90% of the total intra-particle surface area. Higher pore volume and surface area values were computed using the Dubinin Radushkevich plot technique; ranging from 0.004-0.04 cm3 g(-1) to 11-102 m2 g(-1) for micro-pore volume and surface area, respectively. Comparison of the C/H ratio and the micro-pore structure showed a strong correlation, suggesting a relationship between the condensation of the skeletal structure and micro-porosity of the soot. These data contradict literature reports that soot particles are non-porous and are consistent with recent literature reports that soil organic matter has large micro-pore surface areas.     

Deodorization of dimethyl sulfide using a discharge approach at room temperature

The traditional technologies for odor removal of thiol usually create either secondary pollution for scrubbing, adsorption, and absorption processes, or sulfur (S) poisoning for catalytic incineration. This study applied a laboratory-scale radio-frequency plasma reactor to destructive percentage-grade concentrations of odorous dimethyl sulfide (CH3SCH3, or DMS). Odor was diminished effectively via reforming DMS into mainly carbon disulfide (CS2) or sulfur dioxide (SO2). The removal efficiencies of DMS elevated significantly with a lower feeding concentration of DMS or a higher applied rf power. A greater inlet oxygen (O2)/DMS molar ratio slightly improved the removal efficiency. In an O2-free environment, DMS was converted primarily to CS2, methane (CH4), acetylene (C2H2), ethylene (C2H4), and hydrogen (H2), with traces of hydrogen sulfide (H2S), methyl mercaptan (CH3SH), and dimethyl disulfide. In an O2-containing environment, the species detected were SO2, CS2, carbonyl sulfide, carbon dioxide (CO2), CH4, C2H4, C2H2, H2, formaldehyde, and methanol. Differences in yield of products were functions of the amounts of added O2 and the applied power. This study provided useful information for gaining insight into the reaction pathways for the DMS dissociation and the formation of products in the plasmolysis and conversion processes.     

铁炭微电解-H2O2法降解二甲基甲酰胺废水

采用铁炭微电解-H2O2法降解二甲基甲酰胺(DMF)废水,探讨了反应时间、pH、铁炭质量比(简写为Fe/C)以及H2O2投加量对DMF去除率的影响.结果表明:(1)当反应时间为60 min、pH为3、Fe/C为3:1时,DMF去除率为73.4％.(2)向反应体系中投加H2O2,DMF去除率明显提高.当H2O2投放量为0.20 mL/L时,DMF去除率达到95.2％.     

Comparison of two reference black carbons using a planar PCB as a model sorbate

In studies assessing sorption of hydrophobic organic compounds (HOCs) in natural systems, the choice of an appropriate reference black carbon, which can represent environmental black carbon (BC), is essential. This study compared isotherms of two commonly available and distinct reference BCs (n-hexane soot (BCRM) and diesel particulate matter (SRM 2975)) and a natural sediment from a source with little black carbon (Lake Hartwell, SC) using 3,3',4-trichlorobiphenyl (IUPAC #35) as a model sorbate. There was greater sorptivity for PCB-35 by BCRM than by SRM 2975. The observed differences in sorption between the two reference black carbons for PCB-35 may be ascribed to the different chemical characteristics of the black carbons. Differences in pore volume distribution at <16A pore width are less likely to be responsible for the observed differences in sorption. The elemental analysis confirmed that BCRM was a pure n-hexane soot because only C, H and O were measured. In contrast, SRM 2975 also contained N and S and a higher O% than BCRM. Compared to the low BC sediment, the two reference BCs had greater pore volume distributions, surface areas, total pore volumes and sorption. The observed nF (i.e., Freundlich exponent) values for PCB indicated greater linearity of the isotherms for the natural sediment than for the reference black carbons. For designing studies of sorption of HOCs in natural systems, in particular, when PCBs are contaminants of concern, results of this study can aid selection of the appropriate reference BCs.     

Treatment of dairy manure using the microwave enhanced advanced oxidation process under a continuous mode operation

The microwave enhanced advanced oxidation process (MW/H(2)O(2)-AOP) was used to treat dairy manure for solubilization of nutrients and organic matters. This study investigated the effectiveness of the MW/H(2)O(2)-AOP under a continuous mode of operation, and compared the results to those of batch operations. The main factors affecting solubilization by the MW/H(2)O(2)-AOP were heating temperature and hydrogen peroxide dosage. Soluble chemical oxygen demand (SCOD) and volatile fatty acids (VFA) increased with an increase of microwave (MW) heating temperature; very high concentrations were obtained at 90°C. Insignificant amounts of ammonia and reducing sugars were released in all runs. An acidic pH condition was required for phosphorus solubilisation from dairy manure. The best yield was obtained at 90°C with an acid dosage of 1.0 %; about 92 % of total phosphorus and 90 % of total chemical oxygen demand were in the soluble forms. The MW/H(2)O(2)-AOP operated in a continuous operation mode showed pronounced synergistic effects between hydrogen peroxide and microwave irradiation when compared to a batch system under similar operating conditions, resulting in much better yields.     

Pressure effect on soot formation in turbulent diffusion flames

Soot formation in a methane air turbulent jet diffusion flame is investigated numerically using a semi-empirical model. The temperature, density and species (the soot precursor C2H2) fields are calculated using detailed chemical kinetic mechanism based on the flamelet library approach. The influence of pressure on the soot formation and the behavior of the semi-empirical model in different flame situations are investigated. It is found that the flame shape and the flame temperature can be well predicted by the flamelet library approach. The calculated soot yield is mostly sensitive to the soot surface growth rate and the increase of pressure. The increase of pressure leads to the increase of soot surface growth rate and therefore to the increase of soot volume fraction. By adjusting a model constant in the soot surface growth rate, the soot emissions in both pressure p = 1 atm and p = 3 atm are properly simulated by the current semi-empirical soot model.     

Effects of operating parameters on advanced oxidation of diuron by the Fenton's reagent: a statistical design approach

Advanced oxidation of diuron in aqueous solution by Fenton's reagent using FeSO(4) as source of Fe(II) was investigated in the absence of light. Effects of operating parameters namely the concentrations of pesticide (diuron), H(2)O(2) and Fe(II) on oxidation of diuron was investigated by using Box-Behnken statistical experiment design and the surface response analysis. Diuron oxidation by the Fenton reagent was evaluated by determining the total organic carbon (TOC), diuron, and adsorbable organic halogen (AOX) removals. Concentration ranges of the reagents resulting in the highest level of diuron oxidation were determined. Diuron removal increased with increasing H(2)O(2) and Fe(II) concentrations up to a certain level. Diuron concentration had a more profound effect than H(2)O(2) and Fe(II) in removal of diuron, TOC and AOX from the aqueous solution. Nearly complete (98.5%) disappearance of diuron was achieved after 15min reaction period. However, only 58% of diuron was mineralized after 240min under optimal operating conditions indicating formation of some intermediate products. Optimal H(2)O(2)/Fe(II)/diuron ratio resulting in the maximum diuron removal (98.5%) was found to be 302/38/20 (mgl(-1)).     

Distribution of PCNs, PCBs, and other POPs together with soot and other organic matter in the marine environment of the Grenlandsfjords, Norway

The apparently dissolved concentration of polychlorinated naphthalenes (PCNs) and three planar polychlorinated biphenyls (pPCBs) were sampled and analysed in the water column of a marine fjord system. We also measured how much of these persistent organic pollutants (POPs) were associated with suspended particles. The field observations showed that an unexpectedly high portion of the pollutants were particle-associated. The factor of deviation from model predictions had positive linear regression on the soot carbon:particulate organic carbon ratio of the particles, and on estimates of the soot-water distribution coefficient for the PCNs. The spatial distribution of surface sediment concentrations of PCNs and polycyclic aromatic hydrocarbons (PAH) were found to consistently follow the sediment content of soot (f(SC)) to a larger extent than the bulk organic matter (f(OC)). There were no systematic differences in the strength of correlation of sediments concentrations of other POPs, i.e. octachlorostyrene and organochlorine pesticides with sediment concentration to f(SC) and f(OC). Mechanisms possible of generating these types of observations, e.g. adsorption to soot carbon in the marine particle, are discussed.     

Aniline degradation by Electro-Fenton and peroxi-coagulation processes using a flow reactor for wastewater treatment

The degradation of 10-30 l of a 1000 ppm aniline solution in 0.050 M Na2SO4 + H2SO4 at pH 3.0 and 40 degrees C by Electro-Fenton and peroxi-coagulation processes at constant current until 20 A has been studied using a pilot flow reactor in recirculation mode with a filter-press cell containing an anode and an oxygen diffusion cathode, both of 100 cm2 area. H2O2 is produced by the two-electron reduction of O2 at the cathode, being accumulated with a current efficiency between 60% and 80% at the first stages of electrolyses performed with a Ti/Pt anode. In the presence of 1 mM Fe2+, less H2O2 is accumulated, but it is not detected using an Fe anode. The Electro-Fenton process with 1 mM Fe2+ and a Ti/Pt or DSA anode yields an insoluble violet polymer, while the soluble total organic carbon (TOC) is gradually removed, reaching 61% degradation after 2 h at 20 A. In this treatment, pollutants are preferentially oxidized by hydroxyl radicals formed in solution from reaction of Fe2+ with H2O2. The peroxi-coagulation process with an Fe anode has higher degradation power, allowing to remove more than 95% of pollutants at 20 A, since some intermediates coagulate with the Fe(OH)3 precipitate formed. Both advanced electrochemical oxidation processes (AEOPs) show moderate energy costs, which increase with increasing electrolysis time and applied current.     

PAH and soot emissions from burning components of medical waste: examination/surgical gloves and cotton pads

This is a laboratory investigation on the emissions from batch combustion of representative infectious ("red bag") medical waste components, such as medical examination latex gloves and sterile cotton pads. Plastics and cloth account for the majority of the red bag wastes by mass and, certainly, by volume. An electrically heated, horizontal muffle furnace was used for batch combustion of small quantities of shredded fuels (0.5-1.5 g) at a gas temperature of approximately 1000 degrees C. The residence time of the post-combustion gases in the furnace was approximately 1 s. At the exit of the furnace, the following emissions were measured: CO, CO2, NOx, particulates and polynuclear aromatic compounds (PACs). The first three gaseous emissions were measured with continuous gas analyzers. Soot and PAC emissions were simultaneously measured by passing the furnace effluent through a filter (to collect condensed-phase PACs) and a bed of XAD-4 adsorbent (to capture gaseous-phase PACs). Analysis involved soxhlet extraction, followed by gas chromatography-mass spectrometry (GC-MS). Results were contrasted with previously measured emissions from batch combustion of pulverized coal and tire-derived fuel (TDF) under similar conditions. Results showed that the particulate soot) and cumulative PAC emissions from batch combustion of latex gloves were more than an order of magnitude higher than those from cotton pads. The following values are indicative of the relative trends (but not necessarily absolute values) in emission yields: 26% of the mass of the latex was converted to soot, 11% of which was condensed PAC. Only 2% of the mass of cotton pads was converted to soot, and only 3% of the weight of that soot was condensed PAC. The PAC yields from latex were comparable to those from TDF. The PAC yields from cotton were higher than those from coal. A notable exception to this trend was that the three-ring gas-phase PAC yields from cotton were more significant than those from latex. Emission yields of CO and CO2 from batch combustion of cotton were, respectively, comparable and higher than those from latex, despite the fact that the carbon content of cotton was half that of latex. This is indicative of the more effective combustion of cotton. Nearly all of the mass of carbon of cotton gasified to CO and CO2 while only small fractions of the carbon in latex were converted to CO2 and CO (20% and 10%, respectively). Yields of NOx from batch combustions of latex and cotton accounted for 15% and 12%, respectively, of the mass of fuel nitrogen indicating that more fuel nitrogen was converted to NOx in the former case, possibly due to higher flame temperatures. No SO2 emissions were detected, indicating that during the fuel-rich combustion of latex, its sulfur content was converted to other compounds (such as H2S) or remained in the soot.