某自来水厂超滤膜污染物成分及化学清洗效果案例分析

以江苏某自来水厂混凝-超滤工艺中PVC中空纤维超滤膜为对象,采用2种化学清洗剂HCl溶液、NaOH溶液对污染膜进行了化学清洗,分析洗脱液成分以确定膜污染的构成,并考察不同清洗剂在实际工程中的应用效果。通过ICP-OES、 EEM、 TOC分析仪对污染膜洗脱液进行了成分分析,同时采用SEM和ATRFTIR对清洗前后的膜表面形貌及表面官能团进行表征。结果表明,膜污染物不仅包含蛋白类、多糖类和腐殖酸的有机污染物,还包含以Ca、Mg、Si、Fe元素为主的无机污染物。NaOH溶液除了能够洗脱更多的有机物,还可以有效地去除硅。而HCl溶液则对大分子有机物、疏水性有机物以及Ca、 Mg、 Fe有较好的清洗效果。HCl溶液的pH越低,或者NaOH溶液的pH越高,清洗效果越好。在工程实际清洗过程中,采用先酸后碱的组合方式,能够获得较高的膜通量。     

外置管式MBR处理垃圾焚烧渗沥液中的膜污染

采用外置管式膜生物反应器进一步处理垃圾焚烧渗沥液生化出水,研究水洗和化学洗后污染膜的清洗效果。采用扫描电镜、傅里叶红外光谱对膜表面污染物进行分析;采用变性梯度凝胶电泳技术分析了膜表面泥饼层中细菌群落结构。实验结果表明,采用低压力(0.03 MPa)、高流速(2.84 m/s)的清水洗能使膜通量恢复到45%;化学清洗采用p H=2的盐酸酸洗较好。两者清洗方法结合能使膜通量恢复至初始通量的88%。膜表面污染物主要由无机垢体和蛋白质多糖类物质构成,膜表面泥饼层中的细菌主要含有芽孢杆菌、腐螺旋菌、红杆菌等。     

叠式空气隙膜蒸馏组件膜污染实验研究

采用一种具有旋流结构的多层层叠式空气隙膜蒸馏膜组件,以20 g/L氯化钠盐水为热工质,考察在70℃条件下膜污染情况,实验结果表明,一个周期的连续运行和间歇性操作膜表面在高温下较快进入膜污染,8个周期后膜通量下降为初始通量的42%。膜表面有大量黄色附着物,电镜SEM分析显示,膜表面被不均匀堆积的颗粒状污染物及长方体结晶物覆盖,能谱EDS分析,污染物有极少量NaCl结晶的Na、Cl元素,还有O、C、Mg、Cu和Fe等元素。污染膜经5%盐酸溶液清洗后无机垢沉淀被去除,表观效果较好。     

膜生物反应器中膜的清洗方法和机理研究

研究了膜生物反应器处理盥洗废水时 ,水力清洗、酸洗、碱洗等不同组合形式对膜的清洗效果。结果表明 ,水力清洗可以较彻底地去除运行初期的膜表面沉积物 ,使膜通量有较大程度的恢复。对运行时间较长的膜来说 ,有机物和微生物是造成膜污染的主要原因。清水冲洗后用 0 0 5 %NaClO浸泡 1h ,再用 0 5 %的H2 SO4浸泡 1h是盥洗废水处理用膜有效的清洗方法 ,清水膜通量可恢复至 1 0 0 %。     

荷负电超滤膜同时去除水中天然有机物和铅离子

通过特定的化学反应对截留分子量为30 k D的再生纤维素(RC)超滤膜进行改性,得到荷负电超滤膜,并研究了其表面荷电性能。选用腐殖酸作为天然有机物的代表物质,研究荷负电改性膜同时去除溶液中腐殖酸和铅离子,主要考察了p H值和腐殖酸铅离子络合作用对两者截留率的影响,并对比了荷负电膜和未改性膜去除天然有机物和铅离子的研究结果。得到如下结论:(1)在酸性及中性溶液环境下,随着p H值的升高,荷负电超滤膜对腐殖酸和铅离子的截留率都提高。(2)铅离子与腐殖酸共存时,腐殖酸铅离子络合体的荷负电性相比于原腐殖酸分子降低,荷负电超滤膜对混合溶液中腐殖酸的截留率有一定程度降低,络合在腐殖酸表面的铅离子随着腐殖酸的截留而被截留,铅离子截留率得到一定程度提升。(3)由于腐殖酸与铅离子络合体带负电,其与荷负电膜之间存在静电作用,所以荷负电改性膜对腐殖酸和铅离子的截留率比未改性中性膜高。     

天然有机物对PVDF超滤膜的污染行为及AFM表征

为了进一步研究各类型污染物对自制PVDF超滤膜的污染机制,分别采用DAX-8,XAD-4型吸附树脂将西安市灞河水分为亲水性、强疏水性及弱疏水性组分,考察了天然有机物(NOM)对膜通量衰减的影响、污染层的表面粗糙度和结构、各类型污染物与膜之间黏附力。实验结果表明:(1)3种组分对PVDF膜的污染程度为亲水性组分强疏水性组分弱疏水性组分;(2)污染后膜表面粗糙度大于新膜表面粗糙度,膜表面污染层粗糙度越大,膜通量越容易恢复;(3)过滤初期,膜与污染物之间的力占主导作用,且亲水性污染物-PVDF膜之间的力强疏水性污染物-膜弱疏水性污染物-膜;(4)过滤后期,污染物与污染物之间的力占主导作用,且亲水性污染物之间力强疏水性污染物弱疏水性污染物。     

微滤膜垢分形生长的过程模拟

基于微滤膜系统污垢形成机制和分形理论,建立微滤过程膜表面混合垢生长DLA模型,并通过实验验证了模型模拟的可行性和准确性。选取不同运行周期条件下微滤膜系统中的受污染膜丝,进行膜垢污染生长的实时测试,并与不同运行条件下模型的动态模拟结果进行实际比较分析,结果表明两者分形维数相近,且分形维数与膜污染程度呈正相关,说明该模型能够动态表征膜污染水平,可揭示出微滤过程中膜垢生长的动态变化规律,预测出膜材料的受污染水平。     

微波辅助-活性炭法处理电厂EDTA锅炉清洗废水可行性研究

采用微波辅助-活性炭法处理电厂EDTA锅炉清洗废水,研究了微波辐射时间、微波功率以及再生次数对活性炭吸附能力的影响,并根据实验结果设计了工艺流程,分析了微波辅助-活性炭法处理电厂EDTA锅炉清洗废水的可行性.研究表明,微波辅助-活性炭法处理EDTA清洗废水的最佳微波辐射时间和微波功率分别为5 min和680 W,微波辐...     

富含腐殖酸还原混合菌的污泥厌氧降解对乙酰氨基酚的机制

以杭州市四堡污水处理厂的厌氧污泥为接种污泥,驯化富集了厌氧腐殖酸还原混合菌,加入不同的腐殖酸和碳源以优化驯化条件.结果表明,利用驯化厌氧污泥降解对乙酰氨基酚,1周降解时间内,驯化1个月的含腐殖酸还原混合菌群污泥比普通厌氧污泥降解率高34%,驯化半年的成熟厌氧污泥降解效果更好,降解率达90%以上.驯化厌氧污泥的最佳pH为7.0,Fe3 与腐殖酸同时存在时能进一步提高对乙酰氨基酚的厌氧生物降解效果.     

腐殖酸对生物炭吸附水环境中雌激素的影响

以玉米秸秆为原料,通过500℃限氧裂解制备生物炭(记为500BC),并采用批量吸附实验对比500BC及腐殖酸负载后生物炭(记为500BC-HA)对于水环境中两种雌激素(双酚A(BPA)和17α-乙炔雌二醇(EE2))的吸附性能及作用机制。结果表明,腐殖酸分子可阻塞部分500BC孔隙,使500BC的孔径、孔容及比表面积下降,负载腐殖酸后,500BC的比表面积由8.43m~2/g减小至4.40m~2/g,孔径从26.1nm减小至3.2nm,孔容由0.018cm~3/g下降至0.001cm~3/g;与500BC相比,500BC-HA对BPA、EE2的吸附能力均明显降低,一方面是因为腐殖酸分子占据了500BC表面的吸附点位并堵塞部分孔隙,使其吸附能力降低,另一方面腐殖酸负载后引入更多的含氧官能团,使500BC表面疏水性降低,与雌激素间的疏水作用减弱。腐殖酸负载质量浓度为0～10mg/L时,增加负载质量浓度对500BC吸附性能影响明显,当负载质量浓度大于10mg/L时,腐殖酸在500BC表面达到饱和,继续增加负载浓度对500BC的吸附性能不再产生影响。     

微波辅助双氧水氧化降解水中磺胺二甲嘧啶

采用微波辐照技术辅助双氧水氧化降解水中磺胺二甲嘧啶（SM2）,研究了微波辅助双氧水氧化降解水中SM2的影响因素。结果表明,单纯使用微波辐照并不能显著降解SM2,而微波辐照可显著促进双氧水对SM2的氧化作用,提高SM2的降解率。在初始浓度为50 mg/L,微波功率为900 W,加入0.25 mL质量分数为30%的双氧水,pH值为4的条件下辐照6 min,SM2的降解率可达96.5%,COD去除率为72%。     

TiO2光催化复合分离膜对水中天然有机物的去除

在水源污染越来越严重、水质标准日益严格的背景下,超滤(UF)已逐渐成为替代饮用水常规处理技术的最佳选择之一。本研究中采用相转化法,将聚偏氟乙烯(PVDF)、聚乙二醇(PEG)和二氧化钛(TiO₂)共混制得光催化复合分离膜并对其进行扫描电子显微镜(SEM)、原子力显微镜(AFM)和X射线能谱仪(EDS)等相应的表征。比较了有无光照条件下,PVDF-PEG和PVDF-PEG-TiO₂膜对腐殖酸(HA)的截留和超滤过程中的膜污染情况。研究结果表明,TiO₂光催化复合分离膜能提高对水中天然有机物的去除并同时降低膜污染。紫外光照强度越强,PVDF-PEG-TiO₂膜的抗污染性能越好。另外,光催化能更有效地减少超滤初始浓度较低的腐殖酸溶液过程中的膜通量衰减。     

TiO_2光催化对微滤去除腐殖酸的膜污染控制研究

着重研究了不同紫外灯光源和照射时间条件下,TiO_2光催化(PCO)对微滤去除腐殖酸过程中的膜污染控制,并探讨了膜污染的控制机理。研究结果表明,TiO_2光催化能有效提高微滤对腐殖酸的去除,同时降低膜通量的下降,起到有效控制膜污染的作用。进一步的实验分析表明,TiO_2光催化控制膜污染的主要机理在于将腐殖酸降解为易于被TiO_2吸附的小分子量物质,吸附腐殖酸降解产物后的TiO_2聚合颗粒粒径增大,易于在膜表面形成更为松散的沉积层,并使膜污染从以膜孔堵塞和沉积层污染为主转化为以沉积层污染为主的可逆性污染。     

Fouling mitigation and cleanability of TiO<Subscript>2</Subscript> photocatalyst-modified PVDF membranes during ultrafiltration of model oily wastewater with different salt contents

In the present study, TiO₂-coated ultrafiltration membranes were prepared and used for oily water filtration (droplet size <?2 μm). The aim of this work was to investigate the effect of different salt contents on fouling and filtration properties of neat and TiO₂-coated membranes during oil-in-water emulsion filtration. The effect of the TiO₂ coating on the flux, surface free energy, and retention values was measured and compared with the neat membrane values. The cleanability of the fouled TiO₂-coated membranes by UV irradiation was also investigated by measuring flux recovery and contact angles, and the chemical changes during cleaning were characterized by ATR-IR. It was found that increasing the salt content of the model wastewaters, oil-in-water emulsions, increased the zeta potential and the size of the droplets. The presence of the TiO₂ coating decreases the membrane fouling during oily emulsion filtration compared to the neat membrane, due to the hydrophilicity of the coating regardless of the salt content of the emulsions. The neat and coated membrane oil retention was similar, 96?±?2%. The coated membrane can be effectively cleaned with UV irradiation without additional chemicals and a significant flux recovery can be achieved. Monitoring of the cleaning process by following the membrane surface wettability and ATR-IR measurements showed that the recovery of flux does not mean the total elimination of the oil layer from the membrane surface.     

掺Al-TiO2改性膨润土去除微污染水中COD和NH4-N

采用掺Al-TiO2作为改性剂制备改性膨润土,考察了微波辐射功率、辐射时间、TiO2改性剂用量、铝盐掺杂量、pH值对微污染水中COD和NH4-N去除效果的影响。实验表明,微波辐射功率为460 W,辐射时间为8 min,TiO2改性剂用量为1.3 mmol/g,铝盐掺杂量为0.2 mmol/g为最佳制备条件。pH值为6.0,改性膨润土投加量为40 mg/L,沉淀时间为30min时,对微污染水中初始浓度15 mg/L的COD和5 mg/L的NH4-N去除率分别达到92%和59%以上。     

微波辅助光催化降解高浓度活性黑

利用改装的家用微波炉、微波无极灯和TiO2催化剂研究了水中高浓度活性黑的光催化降解.系统考察了TiO2投加量、pH、微波无极灯数量对微波辅助光催化处理效果的影响,得出微波辅助光催化的最佳操作条件,并在最佳条件下对活性黑的脱色及矿化效果进行研究.结果表明,TiO2投加量存在最佳值2 g/L,降低pH和增加微波无极灯数量均可提高活性黑的降解率.在TiO2的投加量为2 g/L,pH =3,微波无极灯数量为3的最佳光催化条件下,400 mg/L的活性黑溶液反应180 min时可实现完全脱色,反应300 min时,TOC去除率高达89.1％.     

Effect of inorganic and organic solutes on zero-valent aluminum-activated hydrogen peroxide and persulfate oxidation of bisphenol A

The effect of varying inorganic (chloride, nitrate, sulfate, and phosphate) and organic (represented by humic acid) solutes on the removal of aqueous micropollutant bisphenol A (BPA; 8.8 μM; 2 mg/L) with the oxidizing agents hydrogen peroxide (HP; 0.25 mM) and persulfate (PS; 0.25 mM) activated using zero-valent aluminum (ZVA) nanoparticles (1 g/L) was investigated at a pH of 3. In the absence of the solutes, the PS/ZVA treatment system was superior to the HP/ZVA system in terms of BPA removal rates and kinetics. Further, the HP/ZVA process was not affected by nitrate (50 mg/L) addition, whereas chloride (250 mg/L) exhibited no effect on the PS/ZVA process. The negative effect of inorganic anions on BPA removal generally speaking increased with increasing charge in the following order: NO₃^? (no inhibition)?<?Cl^? (250 mg/L)?=?SO₄^2??<?PO₄^3? for HP/ZVA and Cl^? (250 mg/L; no inhibition)?<?NO₃^??<?SO₄^2??<?PO₄^3? for PS/ZVA. Upon addition of 20 mg/L humic acid representing natural organic matter, BPA removals decreased from 72 and 100% in the absence of solutes to 24 and 57% for HP/ZVA and PS/ZVA treatments, respectively. The solute mixture containing all inorganic and organic solutes together partly suppressed the inhibitory effects of phosphate and humic acid on BPA removals decreasing to 46 and 43% after HP/ZVA and PS/ZVA treatments, respectively. Dissolved organic carbon removals were obtained in the range of 30 and 47% (the HP/ZVA process), as well as 47 and 57% (the PS/ZVA process) for the experiments in the presence of 20 mg/L humic acid and solute mixture, respectively. The relative Vibrio fischeri photoluminescence inhibition decreased particularly for the PS/ZVA treatment system, which exhibited a higher treatment performance than the HP/ZVA treatment system.     

Fenton试剂法降解餐厨垃圾异味

自行设计Fenton试剂法降解还原性气体异味的反应器,研究了Fenton试剂法处理餐厨垃圾异味主要成分(苯、乙酸乙酯、苯乙烯)的降解效果。以苯为典型代表物,优化得出该实验的最佳反应条件为:pH=3,FeSO4.7H2O投加量为1 g/L液相,30%H2O2投加量为10 mL/L液相,紫外光源辅助。结果证明,Fenton试剂法处理单一异味气体的效果较理想,在前180 min内能达到90%以上,该法在处理气态异味污染物方面具有广阔的应用前景。     

Effect of soil and sediment composition on acetochlor sorption and desorption

Background, aim, and scope  Herbicide fate and its transport in soils and sediments greatly depend upon sorption–desorption processes. Quantitative determination of herbicide sorption–desorption is therefore essential for both the understanding of transport and the sorption equilibrium in the soil/sediment–water system; and it is also an important parameter for predicting herbicide fate using mathematical simulation models. The total soil/sediment organic carbon content and its qualitative characteristics are the most important factors affecting sorption–desorption of herbicides in soil or sediment. Since the acetochlor is one of the most frequently used herbicides in Slovakia to control annual grasses and certain annual broad-leaved weeds in maize and potatoes, and posses various negative health effects on human beings, our aim in this study was to investigate acetochlor sorption and desorption in various soil/sediment samples from Slovakia. The main soil/sediment characteristics governing acetochlor sorption–desorption were also identified. Materials and methods  The sorption–desorption of acetochlor, using the batch equilibration method, was studied on eight surface soils, one subsurface soil and five sediments collected from the Laborec River and three water reservoirs. Soils and sediments were characterized by commonly used methods for their total organic carbon content, distribution of humus components, pH, grain-size distribution, and smectite content, and for calcium carbonate content. The effect of soil/sediment characteristics on acetochlor sorption–desorption was examined by simple correlation analysis. Results  Sorption of acetochlor was expressed as the distribution coefficient (K _d). K _d values slightly decreased as the initial acetochlor concentration increased. These values indicated that acetochlor was moderately sorbed by soils and sediments. Highly significant correlations between the K _d values and the organic carbon content were observed at both initial concentrations. However, sorption of acetochlor was most closely correlated to the humic acid carbon, and less to the fulvic acid carbon. The total organic carbon content was found to also significantly influence acetochlor desorption. Discussion  Since the strong linear relationship between the K _d values of acetochlor and the organic carbon content was already released, the corresponding K _oc values were calculated. Considerable variation in the K _oc values suggested that other soil/sediment parameters besides the total soil organic carbon content could be involved in acetochlor sorption. This was revealed by a significant correlation between the K _oc values and the ratio of humic acid carbon to fulvic acid carbon (C_HA/C_FA). Conclusions  When comparing acetochlor sorption in a range of soils and sediments, different K _d values which are strongly correlated to the total organic carbon content were found. Concerning the humus fractions, the humic acid carbon content was strongly correlated to the K _d values, and it is therefore a better predictor of the acetochlor sorption than the total organic carbon content. Variation in the K _oc values was attributed to the differences in distribution of humus components between soils and sediments. Desorption of acetochlor was significantly influenced by total organic carbon content, with a greater organic carbon content reducing desorption. Recommendations and perspectives  This study examined the sorption–desorption processes of acetochlor in soils and sediments. The obtained sorption data are important for qualitative assessment of acetochlor mobility in natural solids, but further studies must be carried out to understand its environmental fate and transport more thoroughly. Although, the total organic carbon content, the humus fractions of the organic matter and the C_HA/C_FA ratio were sufficient predictors of the acetochlor sorption–desorption. Further investigations of the structural and chemical characteristics of humic substances derived from different origins are necessary to more preciously explain differences in acetochlor sorption in the soils and sediments observed in this study.