Quick vaporization of sprayed sodium hypochlorite (NaClO(aq)) for simultaneous removal of nitrogen oxides (NOx), sulfur dioxide (SO2), and mercury (Hg0)

Sodium hypochlorite (NaClO) has been widely used as a chemical additive for enhancing nitrogen oxide (NO_x; NO + NO₂), sulfur dioxide (SO₂), and mercury (Hg⁰) removals in a wet scrubber. However, they are each uniquely dependent on NaClO_(aq) pH, hence making the simultaneous control difficult. In order to overcome this weakness, we sprayed low liquid-to-gas (L/G) ratio (0.1 L/Nm³) of NaClO_(aq) to vaporize quickly at 165 °C. Results have shown that the maximized NO_x, SO₂, and Hg⁰ removals can be achieved at the pH range between 4.0 and 6.0. When NO_x and Hg⁰ coexist with SO₂, in addition, their removals are significantly enhanced by reactions with solid and gaseous by-products such as NaClO_(s), NaClO_2(s), OClO, ClO, and Cl species, originated from the reaction between SO₂ and NaClO_(aq). We have also demonstrated the feasibility of this approach in the real flue gases of a combustion plant and observed 50%, 80%, and 60% of NO_x, SO₂, and Hg⁰ removals, respectively. These findings led us to conclude that the spray of NaClO_(aq) at a relatively high temperature at which the sprayed solution can vaporize quickly makes the simultaneous control of NO_x, SO₂, and Hg⁰ possible.

Implications: The simple spray of NaClO_(aq) at temperatures above 165 °C can cause the simultaneous removal of gaseous NO_x, SO₂, and Hg⁰ by its quick vaporization. Their maximized removals are achieved at the pH range between 4.0 and 6.0. NO_x and Hg⁰ removals are also enhanced by gaseous and solid intermediate products generated from the reaction of SO₂ with NaClO_(aq). The feasibility of this approach has been demonstrated in the real flue gases of a combustion plant.     

Effects of Sulfur Dioxide and Nitric Oxide on Mercury Oxidation and Reduction under Homogeneous Conditions

Abstract

This paper is particularly related to elemental mercury (Hg⁰) oxidation and divalent mercury (Hg²⁺) reduction under simulated flue gas conditions in the presence of nitric oxide (NO) and sulfur dioxide (SO₂). As a powerful oxidant and chlorinating reagent, Cl₂ has the potential for Hg oxidation. However, the detailed mechanism for the interactions, especially among chlorine (Cl)-containing species, SO₂, NO, as well as H₂O, remains ambiguous. Research described in this paper therefore focused on the impacts of SO₂ and NO on Hg⁰ oxidation and Hg²⁺ reduction with the intent of unraveling unrecognized interactions among Cl species, SO₂, and NO most importantly in the presence of H₂O. The experimental results demonstrated that SO₂ and NO had pronounced inhibitory effects on Hg⁰ oxidation at high temperatures when H₂O was also present in the gas blend. Such a demonstration was further confirmed by the reduction of Hg²⁺ back into its elemental form. Data revealed that SO₂ and NO were capable of promoting homogeneous reduction of Hg²⁺ to Hg⁰ with H₂O being present. However, the above inhibition or promotion disappeared under homogeneous conditions when H₂O was removed from the gas blend.     

A Predictive Mechanism for Mercury Oxidation on Selective Catalytic Reduction Catalysts under Coal-Derived Flue Gas

Abstract

This paper introduces a predictive mechanism for elemental mercury (Hg⁰) oxidation on selective catalytic reduction (SCR) catalysts in coal-fired utility gas cleaning systems, given the ammonia (NH₃)/nitric oxide (NO) ratio and concentrations of Hg⁰ and HCl at the monolith inlet, the monolith pitch and channel shape, and the SCR temperature and space velocity. A simple premise connects the established mechanism for catalytic NO reduction to the Hg⁰ oxidation behavior on SCRs: that hydrochloric acid (HCl) competes for surface sites with NH₃ and that Hg⁰ contacts these chlorinated sites either from the gas phase or as a weakly adsorbed species. This mechanism explicitly accounts for the inhibition of Hg⁰ oxidation by NH₃, so that the monolith sustains two chemically distinct regions. In the inlet region, strong NH₃ adsorption minimizes the coverage of chlorinated surface sites, so NO reduction inhibits Hg⁰ oxidation. But once NH₃ has been consumed, the Hg⁰ oxidation rate rapidly accelerates, even while the HCl concentration in the gas phase is uniform. Factors that shorten the length of the NO reduction region, such as smaller channel pitches and converting from square to circular channels, and factors that enhance surface chlorination, such as higher inlet HCl concentrations and lower NH₃/NO ratios, promote Hg⁰ oxidation.

This mechanism accurately interprets the reported tendencies for greater extents of Hg⁰ oxidation on honeycomb monoliths with smaller channel pitches and hotter temperatures and the tendency for lower extents of Hg⁰ oxidation for hotter temperatures on plate monoliths. The mechanism also depicts the inhibition of Hg⁰ oxidation by NH₃ for NH₃/NO ratios from zero to 0.9. Perhaps most important for practical applications, the mechanism reproduces the reported extents of Hg⁰ oxidation on a single catalyst for four coals that generated HCl concentrations from 8 to 241 ppm, which covers the entire range encountered in the U.S. utility industry. Similar performance is also demonstrated for full-scale SCRs with diverse coal types and operating conditions.     

Study on the removal of elemental mercury from simulated flue gas by Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>-CeO<Subscript>2</Subscript>/AC at low temperature

Fe₂O₃ and CeO₂ modified activated coke (AC) synthesized by the equivalent-volume impregnation were employed to remove elemental mercury (Hg⁰) from simulated flue gas at a low temperature. Effects of the mass ratio of Fe₂O₃ and CeO₂, reaction temperature, and individual flue gas components including O₂, NO, SO₂, and H₂O (g) on Hg⁰ removal efficiency of impregnated AC were investigated. The samples were characterized by Brunauer–Emmett–Teller (BET), X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). Results showed that with optimal mass percentage of 3 % Fe₂O₃ and 3 % CeO₂ on Fe3Ce3/AC, the Hg⁰ removal efficiency could reach an average of 88.29 % at 110 °C. Besides, it was observed that O₂ and NO exhibited a promotional effect on Hg⁰ removal, H₂O (g) exerted a suppressive effect, and SO₂ showed an insignificant inhibition without O₂ to some extent. The analysis of XPS indicated that the main species of mercury on used Fe3Ce3/AC was HgO, which implied that adsorption and catalytic oxidation were both included in Hg⁰ removal. Furthermore, the lattice oxygen, chemisorbed oxygen, and/or weakly bonded oxygen species made a contribution to Hg⁰ oxidation.     

Simultaneous removal of NOx,SO2, and Hg from flue gas in FGD absorber with oxidant injection (NaClO2)– full-scale investigation

ABSTRACT

This article presents the results of an industrial-scale study (on 400 MW_e lignite fired unit) of simultaneous NO_x, SO₂, and Hg^T removal in FGD absorber with oxidant injection (NaClO₂) into flue gas. It was confirmed that the injection of sodium chlorite upstream the FGD (Flue Gas Desulfurization) absorber oxidize NO to NO₂, Hg⁰ to Hg²⁺, and enhancing NO_x and Hg^T removal efficiency from exhaust gas in FGD absorber. Mercury removal efficiency grows with the rise of degree of oxidation NO to NO₂ and was limited by the phenomenon of re-emission. For NO_x removal the most critical parameters is slurry pH and temperature. There was no negative effect on sulfur dioxide removal efficiency caused by oxidant injection in tested FGD absorber. Based on the data provided, NO_x and Hg^T emissions can be reduced by adjusting the FGD absorber operating parameters combined with oxidant injection.     

Gas-phase elemental mercury removal in a simulated combustion flue gas using TiO2 with fluorescent light

A previously proposed technology incorporating TiO₂ into common household fluorescent lighting was further tested for its Hg⁰ removal capability in a simulated flue-gas system. The flue gas is simulated by the addition of O₂, SO₂, HCl, NO, H₂O, and Hg⁰, which are frequently found in combustion facilities such as waste incinerators and coal-fired power plants. In the O₂ + N₂ + Hg⁰ environment, a Hg⁰ removal efficiency (η_Hg) greater than 95% was achieved. Despite the tendency for η_Hg to decrease with increasing SO₂ and HCl, no significant drop was observed at the tested level (SO₂: 5–300 ppm_v, HCl: 30–120 ppm_v). In terms of NO and moisture, a significant negative effect on η_Hg was observed for both factors. NO eliminated the OH radical on the TiO₂ surface, whereas water vapor caused either the occupation of active sites available to Hg⁰ or the reduction of Hg₀ by free electron. However, the negative effect of NO was minimized (η_Hg > 90%) by increasing the residence time in the photochemical reactor. The moisture effect can be avoided by installing a water trap before the flue gas enters the Hg⁰ removal system.

Implications: This paper reports a novel technology for a removal of gas-phase elemental mercury (Hg⁰) from a simulated flue gas using TiO₂-coated glass beads under a low-cost, easily maintainable household fluorescent light instead of ultraviolet (UV) light. In this study, the effects of individual chemical species (O₂, SO₂, HCl, NO, and water vapor) on the performance of the proposed technology for Hg⁰ removal are investigated. The result suggests that the proposed technology can be highly effective, even in real combustion environments such as waste incinerators and coal-fired power plants.     

Investigation of Selective Catalytic Reduction Impact on Mercury Speciation under Simulated NOx Emission Control Conditions

Abstract

Selective catalytic reduction (SCR) technology increasingly is being applied for controlling emissions of nitrogen oxides (NO_x) from coal-fired boilers. Some recent field and pilot studies suggest that the operation of SCR could affect the chemical form of mercury (Hg) in coal combustion flue gases. The speciation of Hg is an important factor influencing the control and environmental fate of Hg emissions from coal combustion. The vanadium and titanium oxides, used commonly in the vanadia-titania SCR catalyst for catalytic NO_x reduction, promote the formation of oxidized mercury (Hg²⁺).

The work reported in this paper focuses on the impact of SCR on elemental mercury (Hg⁰) oxidation. Bench-scale experiments were conducted to investigate Hg⁰ oxidation in the presence of simulated coal combustion flue gases and under SCR reaction conditions. Flue gas mixtures with different concentrations of hydrogen chloride (HCl) and sulfur dioxide (SO₂) for simulating the combustion of bituminous coals and subbituminous coals were tested in these experiments. The effects of HCl and SO₂ in the flue gases on Hg⁰ oxidation under SCR reaction conditions were studied. It was observed that HCl is the most critical flue gas component that causes conversion of Hg⁰ to Hg²⁺ under SCR reaction conditions. The importance of HCl for Hg⁰ oxidation found in the present study provides the scientific basis for the apparent coal-type dependence observed for Hg⁰ oxidation occurring across the SCR reactors in the field.     

湿式烟气脱硫系统同时脱汞研究

研究表明，湿法烟气脱硫装置(WFGD)可去除烟气中绝大部分Hg²⁺，但对单质汞的吸收效果不明显，因此研究提高湿法烟气脱硫系统中单质汞的氧化率的方法对控制汞的排放具有重要意义。综述了WFGD及在此系统中各种添加剂的脱汞性能，认为在添加剂中，气态的臭氧、液态的次氯酸和氯化钠稀溶液、 黄磷乳浊液、氢硫化钠溶液及EDTA的汞去除效果较好，且不会被SO₂大量消耗，可在WFGD系统实现同时脱硫脱汞；而气态的氯气，液态的K₂S₂O₈溶液虽然也有较好的汞去除效果，但因易被SO₂或亚硫酸盐溶液消耗，当在WFGD系统中用其氧化单质汞时，需要对脱硫塔进行分层或其他改造，使烟气中的SO₂被吸收后再控制汞，提高经济性。     

Analytical management of SCR catalyst lifetimes and multipollutant performance

Selective catalytic reduction (SCR) catalysts are deactivated by several mineral and metallic trace elements at highly variable rates determined by fuel quality and furnace firing conditions. With a loss in activity, NO is reduced over a longer inlet length of the SCR monolith, which leaves a shorter trailing section to sustain the most favorable conditions to oxidize Hg⁰ and SO₂. Since virtually no operating SCR was designed for Hg oxidation and since different monoliths are routinely combined as layers in particular units, the Hg oxidation performance of any SCR fleet is largely unmanaged. The analysis in this paper directly relates a measurement or manufacturer’s forecast on the deterioration in NO reduction with age to corresponding estimates for oxidation of Hg⁰. It accommodates any number of catalyst layers with grossly different properties, including materials from different manufacturers and different ages. In this paper, the analysis is applied to 16 full-scale SCRs in the Southern Company fleet to demonstrate that catalyst deactivation disrupts even the most prominent connections among the Hg⁰ oxidation performance of commercial SCRs and the behavior of fresh catalysts at lab, pilot, and even full scale.

Implications: Catalyst deactivation confounds even the most prominent connections among the Hg⁰ oxidation performance of commercial SCRs and the behavior of fresh catalyst at lab, pilot, and even full scale. The halogen dependence has been emphasized throughout the literature on catalytic Hg⁰ oxidation, based on a large database on fresh catalysts. But for deactivated catalysts in commercial SCRs, the number of layers is much more indicative of the Hg⁰ oxidation performance, in that SCRs with four layers perform better than those with three layers, and so on. The new qualified conclusion is that Hg⁰ oxidation is greater for progressively greater HCl concentrations only among SCRs with the same number of layers, even for an assortment of catalyst design specifications and operating conditions.     

Sources and deposition of reactive gaseous mercury in the marine atmosphere

Observations of reactive gaseous mercury (RGM) in marine air show a consistent diurnal cycle with minimum at night, rapid increase at sunrise, maximum at midday, and rapid decline in afternoon. We use a box model for the marine boundary layer (MBL) to interpret these observations in terms of RGM sources and sinks. The morning rise and midday maximum are consistent with oxidation of elemental mercury (Hg⁰) by Br atoms, requiring <2 ppt BrO in most conditions. Oxidation of Hg⁰ by Br accounts for 35–60% of the RGM source in our model MBL, with most of the remainder contributed by oxidation of Hg⁰ by ozone (5–20%) and entrainment of RGM-rich air from the free troposphere (25–40%). Oxidation of Hg⁰ by Cl is minor (3–7%), and oxidation by OH cannot reproduce the observed RGM diurnal cycle, suggesting that it is unimportant. Fitting the RGM observations could be achieved in the model without oxidation of Hg⁰ by ozone (leaving Br as the only significant oxidant) by increasing the entrainment flux from the free troposphere. The large relative diurnal amplitude of RGM concentrations implies rapid loss with a lifetime of only a few hours. We show that this can be quantitatively explained by rapid, mass-transfer-limited uptake of RGM into sea-salt aerosols as HgCl₃^? and HgCl₄^2?. Our results suggest that 80–95% of Hg^II in the MBL should be present in sea-salt aerosol rather than gas-phase, and that deposition of sea-salt aerosols is the major pathway delivering Hg^II to the ocean.     

Low Concentration Mercury Sorption Mechanisms and Control by Calcium-Based Sorbents: Application in Coal-Fired Processes

ABSTRACT

The capture of elemental mercury (Hg⁰) and mercuric chloride (HgCl₂) by three types of calcium (Ca)-based sor-bents was examined in this bench-scale study under conditions prevalent in coal-fired utilities. Ca-based sorbent performances were compared with that of an activated carbon. Hg⁰ capture of about 40% (nearly half that of the activated carbon) was achieved by two of the Ca-based sorbents. The presence of sulfur dioxide (SO₂) in the simulated coal combustion flue gas enhanced the Hg⁰ capture from about 10 to 40%. Increasing the temperature in the range of 65-100 °C also caused an increase in the Hg⁰ capture by the two Ca-based sorbents. Mercuric chloride (HgCl₂) capture exhibited a totally different pattern. The presence of SO₂ inhibited the HgCl₂ capture by Ca-based sorbents from about 25 to less than 10%. Increasing the temperature in the studied range also caused a decrease in HgCl₂ capture. Upon further pilot-scale confirmations, the results obtained in this bench-scale study can be used to design and manufacture more cost-effective mercury sorbents to replace conventional sorbents already in use in mercury control.     

Simultaneous Control of Hg0, SO2, and NOx by Novel Oxidized Calcium-Based Sorbents

Abstract

Efforts to develop multipollutant control strategies have demonstrated that adding certain oxidants to different classes of Ca-based sorbents leads to a significant improvement in elemental Hg vapor (Hg⁰), SO₂, and NO_x removal from simulated flue gases. In the study presented here, two classes of Ca-based sorbents (hydrated limes and silicate compounds) were investigated. A number of oxidizing additives at different concentrations were used in the Ca-based sorbent production process. The Hg⁰, SO₂, and NO_x capture capacities of these oxidant-enriched sorbents were evaluated and compared to those of a commercially available activated carbon in bench-scale, fixed-bed, and fluid-bed systems. Calcium-based sorbents prepared with two oxidants, designated C and M, exhibited Hg⁰ sorp-tion capacities (~100 μg/g) comparable to that of the activated carbon; they showed far superior SO₂ and NO_x sorption capacities. Preliminary cost estimates for the process utilizing these novel sorbents indicate potential for substantial lowering of control costs, as compared with other processes currently used or considered for control of Hg⁰, SO₂, and NO_x emissions from coal-fired boilers. The implications of these findings toward development of multipollutant control technologies and planned pilot and field evaluations of more promising multipollutant sorbents are summarily discussed.     

Atmospheric mercury concentrations and speciation measured from 2004 to 2007 in Reno, Nevada, USA

Atmospheric elemental, reactive and particulate mercury (Hg) concentrations were measured north of downtown Reno, Nevada, USA from November 2004 to November 2007. Three-year mean and median concentrations for gaseous elemental Hg (Hg⁰) were 1.6 and 1.5 ng m⁻³ (respectively), similar to global mean Hg⁰ concentrations. The three-year mean reactive gaseous Hg (RGM) concentration (26 pg m⁻³) was higher than values reported for rural sites across the western United States. Well defined seasonal and daily patterns in Hg⁰ and RGM concentrations were observed, with the highest Hg⁰ concentrations measured in winter and early morning, and RGM concentrations being greatest in the summer and mid-afternoon. Elevated Hg⁰ concentrations in winter were associated with periods of cold, stagnant air; while a regularly observed early morning increase in concentration was due to local source and surface emissions. The observed afternoon increase and high summer values of RGM can be explained by in situ oxidation of gaseous Hg⁰ or mixing of RGM derived from the free troposphere to the surface. Because both of these processes are correlated with the same environmental conditions it is difficult to assess their overall contribution to the observed trends.     

Polarity effect of pulsed corona discharge for the oxidation of gaseous elemental mercury

The effect of polarity on the oxidation of Hg⁰ was examined in the presence of O₂ via a pulsed corona discharge (PCD). The experimental result showed no difference in the energy yield of Hg⁰ oxidation at both positive and negative PCDs (∼8 μg Hg W h⁻¹ at following conditions: total flow rate = 2 L min⁻¹ (Hg⁰ = 50 μg N m⁻³, O₂ = 10%, and N₂ balance), temperature = 150 °C, and specific energy density = 5-15 W h N m⁻³). This suggests that the positive PCD process used to control gaseous air pollutants may play an essential key role in Hg⁰ oxidation because it consumes enough energy (∼15 W h N m⁻³) but an electrical precipitator could not because it consumes less energy (∼0.3 W h N m⁻³) to oxidize Hg⁰.     

Ultra-high adsorption of Hg0 using impregnated activated carbon by selenium

Activated carbon was one of the main adsorptions utilized in elemental mercury (Hg⁰) removal from coal combustion flue gas. However, the high cost and low physical adsorption efficiency of activated carbon injection (ACI) limited its application. In this study, an ultra-high efficiency (nearly 100%) catalyst sorbent-Se_x/Activated carbon (Se_x/AC) was synthesized and applied to remove Hg⁰ in the simulated flue gas, which exhibited 120 times outstanding adsorption performance versus the conventional activated carbon. The Se_x/AC reached 17.98 mg/g Hg⁰ adsorption capacity at 160 °C under the pure nitrogen atmosphere. Moreover, it maintained an excellent mercury adsorption tolerance, reaching the efficiency of Hg⁰ removal above 85% at the NO and SO₂ conditions in a bench-scale fixed-bed reactor. Characterized by the multiple methods, including BET, XRD, XPS, kinetic and thermodynamic analysis, and the DFT calculation, we demonstrated that the ultrahigh mercury removal performance originated from the activated Se species in Se_x/AC. Chemical adsorption plays a dominant role in Hg⁰ removal: Selenium anchored on the surface of AC would capture Hg⁰ in the flue gas to form an extremely stable substance-HgSe, avoiding subsequent Hg⁰ released. Additionally, the oxygen-containing functional groups in AC and the higher BET areas promote the conversion of Hg⁰ to HgO. This work provided a novel and highly efficient carbon-based sorbent -Se_x/AC to capture the mercury in coal combustion flue gas.

Selenium-modified porous activated carbon and the interface functional group promotes the synergistic effect of physical adsorption and chemical adsorption to promote the adsorption capacity of Hg⁰.

     

Formation of particulate sulfur species (sulfate and methanesulfonate) during summer over the Eastern Mediterranean: A modelling approach

To improve our understanding of the mechanisms of particulate sulfur formation (non sea-salt sulfate, nss-SO₄²⁻) and methanesulfonate (MS_x used here to represent the sum of gaseous methanesulfonic acid, MSA, and particulate methanesulfonate, MS⁻) in the eastern Mediterranean and to evaluate the relative contribution of biogenic and anthropogenic sources to the S budget, a chemical box model coupled offline with an aerosol–cloud model has been used.Based on the measurements of gaseous dimethyl sulfide (DMS) and methanesulfonic acid (MSA) and the MSA sticking coefficient determined during the Mediterranean Intensive Oxidant Study (MINOS) experiment, the yield of gaseous MSA from the OH-initiated oxidation of DMS was calculated to be about 0.3%. Consequently, MSA production from gas-phase oxidation of DMS is too small to explain the observed levels of MS⁻. On the other hand, heterogeneous reactions of dimethyl sulfoxide (DMSO) and its gas-phase oxidation product methanesulfinic acid (MSIA) can account for most of the observed MS⁻ levels. The modelling results indicate that about 80% of the production of MS⁻ can be attributed to heterogeneous reactions.Observed submicron nss-SO₄²⁻ levels can be fully explained by homogeneous (photochemical) gas-phase oxidation of sulfur dioxide (SO₂) to sulfuric acid (H₂SO₄), which is subsequently scavenged by (mainly submicron) aerosol particles. The predominant oxidant during daytime is hydroxyl radical (OH) showing very high peak levels in the area during summer mostly under cloudless conditions. Therefore, during summer in the east Mediterranean, heterogeneous sulfate production appears to be negligible. This result is of particular interest for sulfur abatement strategy. On the other hand only about 10% of the supermicron nss-SO₄²⁻ can be explained by condensation of gas-phase H₂SO₄, the rest must be formed via heterogeneous pathways.Marine biogenic sulfur emissions contribute up to 20% to the total oxidized sulfur production (SO₂ and H₂SO₄) in good agreement with earlier estimates for the area.     

Aqueous photoreduction of oxidized mercury species in presence of selected alkanethiols

Mercury is a global environmental contaminant with severe toxicity impact. The chemical processes resulting in the transformation of oxidized mercury species (Hg²⁺) to elemental mercury (Hg⁰), greatly affects the fate and transport of mercury in the natural environment. We hereby provide the first study on the photochemistry of Hg²⁺ with selected alkanethiols (R-SH) as model compounds to represent thiols and thiol-type binding sites on humic substances in natural waters because of the common sulfhydryl functional group (-SH). Kinetic studies were performed using cold vapor atomic fluorescence spectroscopy (CVAFS), the formation of Hg²⁺-thiol complexes (Hg(SR)₂) were confirmed by UV-visible spectrometry and Atmospheric Pressure Chemical Ionization-Mass Spectrometry (APCI-MS), and the reaction products were analyzed using Electron Impact-Mass Spectrometry (EI-MS) and Solid Phase Microextraction coupled with Gas Chromatography-Mass Spectrometry (SPME/GC-MS). Our results indicated that the photoreduction of Hg²⁺ by selected alkanethiols may be mediated by Hg²⁺-thiol complexes to produce Hg⁰. Under our experimental conditions, the apparent first order rate constants obtained for 1-propanethiol, 1-butanethiol, and 1-pentanethiol were (2.0 ± 0.2) × 10⁻⁷ s⁻¹, (1.4 ± 0.1) × 10⁻⁷ s⁻¹, (8.3 ± 0.5) × 10⁻⁸ s⁻¹, respectively. The effects of ionic strength, dissolved oxygen or chloride ion on reaction rates were found to be minimal under our experimental conditions. The identified products of the reaction between oxidized mercury species with selected alkanethiols (C₃-C₅) were Hg⁰ and disulfides (RS-SR). The potential environmental implications are herein discussed.     

Pilot-Scale Study of the Effect of Selective Catalytic Reduction Catalyst on Mercury Speciation in Illinois and Powder River Basin Coal Combustion Flue Gases

Abstract

A study was conducted to investigate the effect of selective catalytic reduction (SCR) catalyst on mercury (Hg) speciation in bituminous and subbituminous coal combustion flue gases. Three different Illinois Basin bituminous coals (from high to low sulfur [S] and chlorine [Cl]) and one Powder River Basin (PRB) subbituminous coal with very low S and very low Cl were tested in a pilot-scale combustor equipped with an SCR reactor for controlling nitrogen oxides (NO_x) emissions. The SCR catalyst induced high oxidation of elemental Hg (Hg⁰), decreasing the percentage of Hg⁰ at the outlet of the SCR to values <12% for the three Illinois coal tests. The PRB coal test indicated a low oxidation of Hg⁰ by the SCR catalyst, with the percentage of Hg⁰ decreasing from ～96% at the inlet of the reactor to ～80% at the outlet. The low Cl content of the PRB coal and corresponding low level of available flue gas Cl species were believed to be responsible for low SCR Hg oxidation for this coal type. The test results indicated a strong effect of coal type on the extent of Hg oxidation.     

Hg Reactions in the Presence of Chlorine Species: Homogeneous Gas Phase and Heterogeneous Gas-Solid Phase

Abstract

The kinetics of Hg chlorination (with HCl) was studied using a flow reactor system with an online Hg analyzer, and speciation sampling using a set of impingers. Kinetic parameters, such as reaction order (α), overall rate constant (k′ ), and activation energy (E _a), were estimated based on the simple overall reaction pathway. The reaction order with respect to C _Hg, k′, and E _a were found to be 1.55, 5.07 x 10^-2exp(-1939.68/T) [(μg/m³)^-0.55(s)^-1], and 16.13 [kJ/mol], respectively. The effect of chlorine species (HCl, CH₂Cl₂) on the in situ Hg capture method previously de-veloped²⁸ was also investigated. The efficiency of capture of Hg by this in situ method was higher than 98% in the presence of chlorine species. Furthermore, under certain conditions, the presence of chlorine enhanced the removal of elemental Hg by additional gas-phase oxidation.     

Catalytic destruction of pentachlorobenzene in simulated flue gas by a V2O5-WO3/TiO2 catalyst

Pentachlorobenzene (PeCB) in simulated flue gas was destructed by a commercial V₂O₅-WO₃/TiO₂ catalyst in this study. The effects of reaction temperature, oxygen concentration, space velocity and some co-existing pollutants on PeCB conversion were investigated. Furthermore, a possible mechanism for the oxidation of PeCB over the vanadium oxide on the catalysts was proposed. Results show that the increase of gas hourly space velocity (GHSV) and the decrease of operating temperature both resulted in the decrease of PeCB removal over the catalyst, while the effect of the oxygen content in the range of 5-20% (v/v) on PeCB conversion was negligible. PeCB decomposition could be obviously affected by the denitration reactions under the conditions because of the positive effect of NO but negative effect of NH₃. The introduction of SO₂ caused the catalyst poisoning, probably due to the sulfur-containing species formed and deposited on the catalyst surface. The PeCB molecules were first adsorbed on the catalyst surface, and then oxidized into the non-aromatic acyclic intermediates, low chlorinated aromatics and maleic anhydride.