Reduction of arsenic uptake by lettuce with ferrous sulfate applied to contaminated soil

Soil contamination by arsenic (As) presents a hazard in many countries and there is a need for techniques to minimize As uptake by plants. A proposed in situ remediation method was tested by growing lettuce (Lactuca sativa L. cv. Kermit) in a greenhouse pot experiment on soil that contained 577 mg As kg(-1), taken from a former As smelter site. All combinations of iron (Fe) oxides, at concentrations of 0.00, 0.22, 0.54, and 1.09% (w/w), and lime, at concentrations of 0.00, 0.27, 0.68, and 1.36% (w/w), were tested in a factorial design. To create the treatments, field-moist soil, commercial-grade FeSO4, and ground agricultural lime were mixed and stored for one week, allowing Fe oxides to precipitate. Iron oxides gave highly significant (P < 0.001) reductions in lettuce As concentrations, down to 11% of the lettuce As concentration for untreated soil. For the Fe oxides and lime treatment combinations where soil pH was maintained nearly constant, the lettuce As concentration declined in an exponential relationship with increasing FeSO4 application rate and lettuce yield was almost unchanged. Iron oxides applied at a concentration of 1.09% did not give significantly lower lettuce As concentrations than the 0.54% treatment. Simultaneous addition of lime with FeSO4, was essential. Ferrous sulfate with insufficient lime lowered soil pH and caused mobilization of Al, Ba, Co, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Pb, Sr, and Zn. At the highest Fe oxide to lime ratios, Mn toxicity caused severe yield loss.     

Soil acidity and manganese in declining and nondeclining sugar maple stands in Pennsylvania

For decades, the hardwood forests of northern Pennsylvania have been subjected to chronic atmospheric loading of acidifying agents. On marginal, high-elevation, unglaciated sites, sugar maples (Acer saccharum Marsh.) have experienced severe decline symptoms and mortality. Accelerated soil acidification, base cation leaching, and increased availability of toxic metals have been suggested as predisposing factors contributing to this decline. Manganese, an essential micronutrient, is also a potentially phytotoxic metal that may be a factor associated with poor sugar maple health on soils vulnerable to acidification from anthropogenic sources. We measured Mn levels in four compartments of the soil-tree system (soil, foliage, xylem wood, and sap) on three sugar maple stands in northern Pennsylvania. Two stands were classified as declining and one was in good health. Negative correlations were found between soil pH and Mn levels in the soil, foliage, sap, and xylem wood. Levels of Mn in these pools were consistently higher on declining sites, which correspondingly exhibited lower levels of Ca and Mg. Species differences between red maple (Acer rubrum L.) and sugar maple at the two declining sites suggested different tolerances to excessive Mn. Molar ratios of Mg/Mn and Ca/Mn were different among sites and showed potential as indicators of soil acidification. Significant correlations among soil, sap, foliage, and xylem wood Mn were also noted. These results show clear Mn differences among sites and, when viewed with recent Mn toxicity experiments and other observational studies, suggest that excessive Mn may play a role in the observed decline and mortality of sugar maple.     

Secondary metabolite concentrations and terpene emissions of Scots pine xylem after long-term forest fertilization

Secondary compounds are known to be associated with the resistance of conifer xylem against insects and fungi. The effects of long-term forest fertilization with nitrogen (N) or with N, calcium (Ca), and phosphorus (P) on secondary compounds in the xylem of 50-yr-old Scots pine (Pinus sylvestris L.) trees were examined. Xylem samples were collected from trees growing in three locations in southern Finland: Vilppula, Padasjoki, and Punkaharju. Forests were fertilized every fifth (Vilppula and Padasjoki) or tenth (Punkaharju) year since the 1950s. We compared concentrations of individual and total monoterpenes and resin acids in the heartwood and sapwood of Scots pine. Terpene emissions were analyzed from the sapwood and total phenolics from the heartwood. Fertilization did not have any significant effect on the concentrations and emissions of xylem monoterpenes. Concentrations of several individual terpenes in sapwood were positively correlated with the corresponding terpene emission. The concentrations of individual resin acids (i.e., abietic and dehydroabietic) decreased significantly in Punkaharju, but increased in the sapwood of N-fertilized trees compared with control ones at Padasjoki and Vilppula. The concentrations of resin acids in the heartwood were not significantly affected by fertilization. Both fertilization treatments decreased the total phenolic concentrations in the heartwood of trees growing in Padasjoki. There was a significant positive correlation between the total phenolics and total resin acid concentration. Overall, resin acids and phenolics seemed be more responsive than monoterpenes to N treatment. These results suggest that forest fertilization might cause slight changes in secondary compound concentrations of xylem, and thus might have significance in the decay resistance of wood.     

Testing the Indicative Value of Magnetic Susceptibility Measurements for Concluding on Site Potentials and Risks Provoked by Fly Ash Deposition

The article presents results of testing the indicative value of magnetic susceptibility for fly ash deposition and its effects on forest site properties. Base saturation and concentrations of Ca and Mg were used as indicators for nutrient pools resulting from fly ash deposition. Concentrations of Fe, Al, Mn, Cd and Black Carbon were used as indicators for risks of leaching. The correlation of magnetic susceptibility with concentrations of nutrient, acidic cations, heavy metals, base saturation and Black Carbon was calculated. Additionally, we tested the suitability of magnetic susceptibility as a parameter in a linear regression based model to predict the concentrations of Ca, Mg, Fe, Al, Mn, Cd and Black Carbon. We were able to show a positive correlation between magnetic susceptibility and the selected indicators. In contrast to previous studies, we were also able to demonstrate the suitability of magnetic susceptibility to predict the size of fly ash deposition influenced nutrient pools mainly for humus layers, especially for Oa horizons. The spatial distribution of magnetic susceptibility showed also a positive correlation with regionalized base saturation. However, because of the data base and other factors impacting the measurement and modeling results, some shortcomings of using a linear regression model must be noted. From these results, we concluded that magnetic susceptibility might be a valuable parameter in a multiple regression based approach, but should not be used alone for predicting effects of fly ash deposition.     

Extractability of elements in sugar maple xylem along a gradient of soil acidity

Dendrochemistry has been used for the historical dating of pollution. Its reliability is questionable due primarily to the radial mobility of elements in sapwood. In the present study, the extractability of seven elements was characterized to assess their suitability for the monitoring of environmental conditions. Nine mature sugar maple trees (Acer saccharum Marsh.), a wide-ranging species in eastern North America that has suffered decline in past decades, were sampled in three Quebec watersheds along a soil acidity gradient. Five-year groups of annual tree rings were treated by sequential chemical extractions using extractants of varying strength (deionized H2O, 0.05 M HCl, and concentrated HNO(3)) to selectively solubilize the elements into three fractions (water-soluble, acid-soluble, and residual). Monovalent K; divalent Ba, Ca, Cd, Mg, Mn; and trivalent Al cations were found mostly in the water-soluble, acid-soluble, and residual fractions, respectively. Forms more likely to be mobile within the tree (water-soluble and acid-soluble) do not seem to be suitable for temporal monitoring because of potential lateral redistribution in sapwood rings. However, certain elements (Cd, Mn) were responsive to current soil acidity and could be used in spatial variation monitoring. Extractability of Al varied according to soil acidity; at less acidic sites, up to 90% of Al was contained in the residual form, whereas on very acidic soils, as much as 45% was found in the water-soluble and acid-soluble fractions. Sequential extractions can be useful for determining specific forms of metals as key indicators of soil acidification.     

Simulated effects of sulfur deposition on nutrient cycling in class I wilderness areas

We predicted the effects of sulfate (SO(4)) deposition on wilderness areas designated as Class I air quality areas in western North Carolina using a nutrient cycling model (NuCM). We used three S deposition simulations: current, 50% decrease, and 100% increase. We measured vegetation, forest floor, and root biomass and collected soil, soil solution, and stream water samples for chemical analyses. We used the closest climate stations and atmospheric deposition stations to parameterize NuCM. The areas were: Joyce Kilmer (JK), Shining Rock (SR), and Linville Gorge (LG). They differ in soil acidity and nutrients, and soil solution and stream chemistry. Shining Rock and LG have lower soil solution base cation and higher acidic ion concentrations than JK. For SR and LG, the soil solution Ca/Al molar ratios are currently 0.3 in the rooting zone (A horizon), indicating Al toxicity. At SR, the simulated Ca/Al ratio increased to slightly above 1.5 after the 30-yr simulation regardless of S deposition reduction. At LG, Ca/Al ratios ranged from 1.6 to 2.4 toward the end of the simulation period, the 100% increase scenario had the lower value. Low Ca/Al ratios suggest that forests at SR and LG are significantly stressed under current conditions. Our results also suggest that SO(4) retention is low, perhaps contributing to their high degree of acidification. Their soils are acidic, low in weatherable minerals, and even with large reductions in SO(4) and associated acid deposition, it may take decades before these systems recover from depletion of exchangeable Ca, Mg, and K.     

RUNOFF OF METALS FROM ALUM-TREATED HORSE MANURE AND MUNICIPAL SLUDGE1

ABSTRACT: Land application of organic soil amendments can increase runoff concentrations of metals such as Fe and Zn, metalbids such as B and As, and non-metals such as P and S that have the potential for causing adverse environmental impacts. Aluminum sulfate, or alum (Al₂(SO₄)3*(14H₂O), can reduce concentrations of some materials in runoff from sites treated with organic amendments. The objectives of this study were to (a) quantify concentrations of selected constituents (Al, As, B, Ca, Cd, Co, Fe, K, Mg, Mn, Mo, Na, P, Pb, 5, Se, Ti, and Zn) in runoff from plots treated with horse manure (mixed with stall bedding) and municipal sludge, (b) assess runoff quality effects of alum addition to those treatments, and (c) determine time variations in concentrations of the constituents. Horse manure and municipal sludge were applied to twelve 2.4 by 6.1 m fescue plots (six each for the manure and sludge). Alum was added to three of the manure-treated and three of the sludge-treated plots. Simulated rainfall (64 mm/h) was applied to the 12 treated plots and to three control (no treatment) plots. The first 0.5 h runoff was sampled and analyzed for the constituents described above. Addition of manure or sludge had no effect on runoff concentrations of the majority of constituents. In some cases (e.g., Al, As, Fe, Zn), however, concentrations were near or in excess of threshold values recommended for marine wildlife protection. Alum addition increased runoff of Al, Ca, K, and 5, due likely to its composition and by the addition of lime to counteract the acidity of alum. Concentration decreases of more than 50 percent were noted for P for the horse manure treatment. No alum effect was detected for P in runoff from the sludge-treated plots, possibly due to relatively stable P forms in the sludge. Runoff concentrations of Al, As, Fe, K, Mn, and P followed an approximately first-order decline with respect to time. Runoff concentrations of Ca and 5, however, peaked during the second runoff sample (four minutes following initiation of runoff), suggesting that differences in mobility and/or transport mechanisms exist among the materials investigated.     

胆汁引流对黑熊体毛中微量元素含量的影响

作者在1990年6～7月采集了胆汁引流黑熊和未手术黑熊的体毛样本,经原子吸收光谱仪和极谱仪测定。结果表明,胆汁引流黑熊雌雄之间体毛中 Se、Zn、Fe、Mg、Cu、Mn、Ca、P 含量差异不显著;胆汁引流1年的黑熊与未手术黑熊相比,体毛中 Ca 含量明显降低、Mn 含量明显增高。因此,在配制黑熊饲料时应重视矿物质的添加量,以提高熊胆产量和质量。     

Distribution and speciation of metals in annual rings of black willow

Information on the spatial distribution and speciation of metals in nonhyperaccumulator plants is lacking. This study used synchrotron X-ray fluorescence (SXRF) compositional imaging to investigate the spatial distribution of Ni, Mn, Cu, Zn, and Fe in annual rings of black willow (Salix nigra L.) collected from a metal-contaminated area, and used X-ray absorption spectroscopy (XAS) to investigate Ni and Mn speciation in regions of the annual rings with elevated Ni concentrations. Annual rings were recollected in early 2003 from an individual known to be enriched with Ni from previous studies. Compositional imaging showed Ni and associated co-contaminants conservatively located in an annual ring. When compared with a corresponding photomicrograph, SXRF compositional images showed that metals were sharply constrained by the boundaries of the annual ring, indicating a sudden onset and cessation of uptake, and a lack of post-growth mobility of the metals. There was a particularly strong correlation between Ni and Mn in the metal-enriched annual ring (r = 0.8822), which suggested similar transport and binding behavior of these elements. X-ray absorption spectroscopy showed Ni and Mn to be present in the 2+ oxidation state. X-ray absorption near edge structure spectroscopy (XANES) fingerprinting of localized, highly Ni-enriched regions within the lumen of willow xylem vessels found similarities with Ni-pectic acid complexes, Ni-histidine, and NiSO4.     

SEDIMENT CHEMISTRY AS INFLUENCED BY VEGETATION AND BEDROCK IN THE SOUTHWESTERN UNITED STATES1

ABSTRACT We hypothesized that sediment from small watersheds with uniform bedrock and a single vegetative community would have uniform chemical characteristics for the sand and fine (silt and clay) size fractions. Channel sediment was collected from three vegetative communities (spruce-fir, mixed conifer, and Ponderosa pine), each on four bedrock types (basalt, limestone, sandstone, and granite), and analyzed for digestable Ca, Mg, Na, K, Cu, Mn, Fe, Zn; total N and P; extractable Ca, Mg, K; cation exchange capacity; and organic matter. With the exception of organic matter content in the sand size fraction, either vegetation, bedrock, or their interaction were significant in explaining the observed variation for all analyses in both size fractions. Replicate studies of sites with similar bedrock and vegetation combinations are needed to determine if each watershed has similar or unique sediment chemistry.     

TRENDS IN PRECIPITATION AND STREAM CHEMISTRY IN A PRISTINE OLD-GROWTH FOREST WATERSHED,OLYMPIC NATIONAL PARK,WASHINGTON1

ABSTRACT: Human induced long-term changes in precipitation and stream chemistry have been observed in eastern North America and Europe, but few long-term studies have been conducted in coastal western North America. The objectives of this research were to determine: (1) time trends in precipitation and stream chemistry in a pristine old-growth forest watershed, and (2) seasonal patterns in precipitation and stream chemistry. It was conducted in 58 ha West Twin Creek Watershed, Hoh River Valley, Olympic National Park, Washington from 1984 to 1993. Vegetation consists of old-growth forest, with western hemlock, Douglas-fir, western redcedar, Pacific silver fir, and Sitka spruce being the dominant tree species. Annual precipitation varied from 2336 to 4518 mm during the study period with the majority of the rain falling between October and May. Chemistry of precipitation was strongly dominated by oceanic influences with Na and Cl being the dominant ions. The chemistry of the stream was influenced by bedrock weathering and was dominated by Ca, HCO₃, and SO₄ and was not strongly related to precipitation chemistry. The pH of precipitation averaged 5.3 over time and ranged from 4.3 to 7.1, while the stream pH averaged 7.5 and ranged from 5.5 to 9.0. There were few long-term trends in the chemical constituents of bulk precipitation or stream water with the exception of a slight decrease in NO₃ in precipitation and an increase of SO₄ in stream water. A trend of decreasing concentrations of Ca, Mg and Na in precipitation also occurred. There were no significant seasonal patterns in precipitation although the highest SO₄ concentrations usually occurred in late spring and summer perhaps due marine algal activity. Strong seasonal trends occurred in concentrations of HCO₃, SO₄, Ca, Mg, and Na in stream water resulting from weathering and stream flow patterns, with highest ion concentrations occurring just before the onset of the rainy season. Pulses of NO₃ in the stream were observed during fall and early winter resulting from the release of NO₃ which had accumulated in soils or sediments.     

Quantitative,chemical, and mineralogical characterization of flue gas desulfurization by-products

The objective of this study was to demonstrate that simple fractionation and selective dissolution techniques can be used to provide detailed chemical and mineralogical analyses of flue gas desulfurization by-products. The material studied was a mine grout prepared as a 1:1 mixture (wt./wt.) of fly ash (FA) and filter cake (FC) with hydrated lime (50 g kg(-1)) added to improve handling. The hydrated lime was composed mostly of calcite (CaCO3), portlandite [Ca(OH)2], lime (CaO), and brucite [Mg(OH)2] (515, 321, 55, and 35 g kg(-1), respectively) and had low (<6 g kg(-1)) concentrations of most trace elements. The FC contained hannebachite (CaSO3 x 0.5H2O) (786 g kg(-1)) with smaller quantities (<10 g kg(-1)) of calcite, quartz (SiO2), brucite, and gypsum (CaSO4 x 2H2O). Except for B and Cu, trace element concentrations were comparable to those in the hydrated lime. The FA contained both magnetic (222 g kg(-1)) and nonmagnetic (778 g kg(-1)) fractions. The former was composed mostly of hematite (Fe2O3), magnetite (Fe3O4), and glass (272, 293, and 287 g kg(-1), respectively), whereas the latter was enriched in glass, quartz, and mullite (Al6Si2O13) (515, 243, and 140 g kg(-1), respectively). Etching with 1% HF showed that 60 to 100% of trace elements were concentrated in the glass, although some metals (Co, Cr, and Mn) were clearly enriched in the magnetic phase. The aged grout contained 147 g kg(-1) ettringite [Ca6Al2(SO4)3(OH)12 x 26H2O] in addition to 314 g kg(-1) hannebachite and 537 g kg(-1) insoluble phases (mullite, quartz, hematite, magnetite, and glass).     

Fly ash and lime-stabilized biosolid mixtures in mine spoil reclamation: simulated weathering

The use of large quantities of neutral coal fly ash (NFA) may be facilitated by co-application with a lime-stabilized biosolid (LSB) for the reclamation of acid mine spoil (AMS). Although NFA may not aid in the mitigation of acid drainage, questions concerning the leachability and mineralogy of native and NFA- and LSB-born metals must be addressed. In this study, the potential long-term influence of LSB and NFA on AMS leachate chemistry and trace element mineralogy was evaluated using laboratory weathering and selective dissolution techniques. The application of LSB at a rate sufficient to neutralize the potential acidity of the AMS increased leachate pH from approximately 3 to 7.5 for the duration of the study. Fly ash rates (1X, 1.5X, and 2X LSB rate) did not affect leachate pH. The dominant electrolytes in all leachates were Ca and SO4, the concentrations of which were mirrored by solution electrical conductivity (EC). Leachate concentrations of Al, Fe, Mn, K, Cu, Ni, and Zn were significantly reduced by LSB application, whereas concentrations of Ca, SO4, Mg, Cl, F, B, and P were increased. Nitrate concentrations were not affected by LSB. With the exception of leachate B, which increased with increasing NFA rate and was regenerated during the weathering study, NFA did not affect leachate composition. Sequential selective dissolution indicated a transformation of Co, Cr, Cu, Ni, Pb, and Zn into less labile mineral pools with weathering. The results of these evaluations suggest that the application of NFA during AMS reclamation would have little effect on leachate chemistry or the mineralogy of trace elements. Thus, the high-volume application of NFA to AMS during reclamation may offer an additional opportunity for the use of this combustion by-product.     

Chemical analysis of soil and leachate from experimental wetland mesocosms lined with coal combustion products

Small-scale (1 m2) wetland mesocosm experiments were conducted over two consecutive growing seasons to investigate the effects on soil and leachate chemistry of using a recycled coal combustion product as a liner. The coal combustion product used as a liner consisted of flue gas desulfurization (FGD) by-products and fly ash. This paper provides the chemical characteristics of mesocosm soil and leachate after 2 yr of experimentation. Arsenic, Ca, and pH were higher in FGD-lined mesocosm surface soil relative to unlined mesocosms. Aluminum was higher in the soils of unlined mesocosms relative to FGD-lined mesocosms. No significant difference of potentially phytotoxic B was observed between lined and unlined mesocosms in the soil. Higher pH, conductivity, and concentrations of Al, B, Ca, K, and S (SO4-S) were observed in leachate from lined mesocosms compared with unlined controls while Fe, Mg, and Mn were higher in leachate from unlined mesocosms. Concentrations of most elements analyzed in the leachate were below national primary and secondary drinking water standards after 2 yr of experimentation. Initially high pH and soluble salt concentrations measured in the leachate from the lined mesocosms may indicate the reason for early effects noted on the development of wetland vegetation in the mesocosms.     

Multivariate analysis of trace metal levels in tannery effluents in relation to soil and water: a case study from Peshawar, Pakistan

Tannery effluents and relevant ground water and soil samples collected from various tanning industries of Peshawar were analyzed for Na, Ca, K, Mg, Fe, Mn, Cr, Co, Cd, Ni, Pb and Zn by the AAS method. The metal concentration data for the three media are reported in terms of basic statistical parameters, metal-to-metal correlations and linear regression analyses. Metal distributions in the three media were quite divergent and showed non-normal distributions with high standard deviation and skewness parameters. Sodium exhibited the highest mean levels of 1,277mg/L, 881mg/L and 12,912mg/kg in the effluent, ground water and soil samples, respectively. Among other metals, Cr concentrations were 410mg/L, 0.145mg/L, 100mg/kg and Ca, 278mg/L, 64.8mg/L, and 2,285mg/kg in the effluent, ground water and soil samples, respectively. Some significant correlations were observed between effluent and soils in terms of Na, Cr, Ni, Co and Pb. The ground water-soil interrelationship suggested that Na levels in the soil and ground water were significantly correlated with each other (r=0.486, P<0.01). Similarly, Cr in the soil is strongly correlated with Ca in ground water (r=0.486, P<0.01). These results were duly supported by the linear regression analysis of data. The source identification studies conducted using Principal Component Analysis (PCA) and Cluster Analysis (CA) evidenced that ground water and soil were being contaminated by the toxic metals emanating from the tannery effluents.     

Major and trace elements of selected pedons in the USA

Few studies of soil geochemistry over large geographic areas exist, especially studies encompassing data from major pedogenic horizons that evaluate both native concentrations of elements and anthropogenically contaminated soils. In this study, pedons (n = 486) were analyzed for trace (Cd, Co, Cr, Cu, Hg, Mn, Ni, Pb, Zn) and major (Al, Ca, Fe, K, Mg, Na, P, Si, Ti, Zr) elements, as well as other soil properties. The objectives were to (i) determine the concentration range of selected elements in a variety of U.S. soils with and without known anthropogenic additions, (ii) illustrate the association of elemental source and content by assessing trace elemental content for several selected pedons, and (iii) evaluate relationships among and between elements and other soil properties. Trace element concentrations in the non-anthropogenic dataset (NAD) were in the order Mn > (Zn, Cr, Ni, Cu) > (Pb, Co) > (Cd, Hg), with greatest mean total concentrations for the Andisol order. Geometric means by horizon indicate that trace elements are concentrated in surface and/or B horizons over C horizons. Median values for trace elements are significantly higher in surface horizons of the anthropogenic dataset (AD) over the NAD. Total Al, Fe, cation exchange capacity (CEC), organic C, pH, and clay exhibit significant correlations (0.56, 0.74, 0.50, 0.31, 0.16, and 0.30, respectively) with total trace element concentrations of all horizons of the NAD. Manganese shows the best inter-element correlation (0.33) with these associated total concentrations. Total Fe has one of the strongest relationships, explaining 55 and 30% of the variation in total trace element concentrations for all horizons in the NAD and AD, respectively.     

Trace elements in camel tissues from a semi-arid region

Trace and minor element concentrations differ in animal tissues as the result of the surrounding environment (feeding plants, soil contaminated with food and drinking water) and animal absorption of these elements. Concentrations of Ag, Au, Ca, Co, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, and Zn were determined from different tissues of camel (inter-costal, scapula, sirloin, flank, front knuckle and front limb) from the semi-arid areas of the Aswan desert (Wadi El-Allaqi) and from Aswan city, Egypt. The study included an assessment of these same elements in the desert and city plants used as food by the camels and in soils from the study areas. The results reveal that camel tissues from the desert areas exhibited higher concentrations of Na, Mg, K, Au, Ag, Cu, Co and Zn than in those of the city camels. These higher levels of element are because of the high concentrations of the same elements in the desert plants and soil of the desert area. This, in turn, depends upon the geological formation differences between the desert area and the city area. Camel tissues appear to concentrate high levels of Mn, Ni, Co and Mg in the scapula while flank portions concentrate high levels of Mg and K. The levels of elements in the camel tissues under study were within the recommended safety baseline levels for camel health and human use, as well as within the appropriate limits in the desert and city plants for camel use.     

Switchgrass biochar affects two aridisols

The use of biochar has received growing attention because of its ability to improve the physicochemical properties of highly weathered Ultisols and Oxisols, yet very little research has focused on its effects in Aridisols. We investigated the effect of low or high temperature (250 or 500°C) pyrolyzed switchgrass () biochar on two Aridisols. In a pot study, biochar was added at 2% w/w to a Declo loam (Xeric Haplocalcids) or to a Warden very fine sandy loam (Xeric Haplocambids) and incubated at 15% moisture content (by weight) for 127 d; a control (no biochar) was also included. Soils were leached with 1.2 to 1.3 pore volumes of deionized HO on Days 34, 62, 92, and 127, and cumulative leachate Ca, K, Mg, Na, P, Cu, Fe, Mn, Ni, Zn, NO-N, NO-N, and NH-N concentrations were quantified. On termination of the incubation, soils were destructively sampled for extractable Cr, Cu, Fe, K, Mg, Mn, Na, Ni, P, Zn, NO-N, and NH-N, total C, inorganic C, organic C, and pH. Compared with 250°C, the 500°C pyrolysis temperature resulted in greater biochar surface area, elevated pH, higher ash content, and minimal total surface charge. For both soils, leachate Ca and Mg decreased with the 250°C switchgrass biochar, likely due to binding by biochar's functional group sites. Both biochars caused an increase in leachate K, whereas the 500°C biochar increased leachate P. Both biochars reduced leachate NO-N concentrations compared with the control; however, the 250°C biochar reduced NO-N concentrations to the greatest extent. Easily degradable C, associated with the 250°C biochar's structural make-up, likely stimulated microbial growth, which caused NO-N immobilization. Soil-extractable K, P, and NO-N followed a pattern similar to the leachate observations. Total soil C content increases were linked to an increase in organic C from the biochars. Cumulative results suggest that the use of switchgrass biochar prepared at 250°C could improve environmental quality in calcareous soil systems by reducing nutrient leaching potential.     

Phosphorus sorption by sediments in a southeastern coastal plain in-stream wetland

A close relationship has been reported between sediment organic C (SedOC) content and its P sorption capacity (P(max)) and total P (TP) concentration. Phosphorus sorbed to organically complexed cations is a proposed explanation for this relationship. The objectives of this study were (i) to determine relationships between in-stream wetland SedOC content and both the sediment's P(max) and TP concentrations, and (ii) to ascertain the role of both organically complexed and oxalate-extractable cations on the sediment P(max) and TP values. The sediment's oxalate-extractable Fe (Fe(ox)) and Al (Al(ox)) contents were determined using acidified ammonium oxalate, while sodium pyrophosphate was used to extract organically complexed cations (Al(pryo), Ca(pyro), Fe(pyro), Mg(pyro), and Mn(pyro)). Both the sediment's P(max) and TP contents were strongly correlated with its SedOC concentration (r(2) > 0.90, P < 0.001). Only the Al(ox) contents were significantly correlated with TP and P(max), suggesting that amorphous Al forms have an important role in P sorption. All five pyrophosphate-extracted cations were significantly correlated with SedOC contents. Regression analyses showed that the Al(pyro) accounted for 88% of the variation in sediment P(max) values, whereas a combination of Al(pyro) and Ca(pyro) accounted for 98% of the variation in sediment TP concentrations. Additionally, Al and Ca chelated by SedOC compounds also have an important role in P binding and indicate that a linkage exists between the wetlands SedOC and P(max) content and its ability to accumulate TP. This study identified that two different mechanisms have significant roles in regulating P sorption by sediments in a southeastern Coastal Plain in-stream wetland.     

Amelioration of physical strength in waste foundry green sands for reuse as a soil amendment

To avoid increasing costs of landfill disposal, it has become increasingly important for U.S. foundries to identify beneficial reuses for the 8 to 12 million tons of waste foundry sand (WFS) generated annually. A major drawback to the reuse of some WFSs as a soil amendment is their high soil strength, under dry conditions, where root growth may be limited. Fifteen WFSs were analyzed for strength to rupture using lab-formed clods, exchangeable cations (Na, Mg, Ca), metal oxide concentration (Fe, Mn, Al, Si), cation exchange capacity (CEC), and % clay. Several WFS samples from gray iron foundries demonstrated high strength to rupture values (> 1.5 MPa), and could potentially restrict root growth in amended soils. The percentage of Na-bentonite exhibited a positive correlation (R(2) = 0.84) with strength to rupture values. When WFSs containing more Na-bentonite were saturated with 1 mol L(-1) Ca ions, strength values decreased by approximately 70%. Waste foundry sands containing less Na-bentonite were saturated with 1 mol L(-1) Na ions and exhibited a threefold increase in strength. Additions of gypsum (up to 9.6 g kg(-1) sand) to high strength waste foundry sands also caused decreases in strength. These results indicate that high strength WFSs have properties similar to hardsetting soils which are caused by high Na(+) clay content and can be ameliorated by the addition of Ca(2+).