PM2.5 Emissions from Aluminum Smelters: Coefficients and Environmental Impact

ABSTRACT

From 2004 to 2009, aiming to better understand implications for its smelters, Rio Tinto Alcan conducted a detailed study of PM_2.5 and PM₁₀ (particulate matter [PM] ≤ 2.5 and 10 μm in aerodynamic diameter, respectively) in its facilities. This involved a two-level study: part 1, emission quantification; and part 2, assessment of aluminum smelter contribution to the surrounding environment. In the first part, U.S. Environmental Protection Agency Other Test Method (OTM) OTM27 and OTM28 are assessed as relevant and efficient methods for measuring fine particle emissions from aluminum smelter stacks. Rio Tinto Alcan has also developed a safe and robust method called CYCLEX to measure PM_2.5 and condensable particulate matter (CPM) at the roof vents of potrooms. This work aims to determine the PM_2.5 emission coefficients of 17, 55, and 417 g·t^?1 of aluminum produced (including CPM) in anode baking furnace exhaust (fume treatment center), at potroom scrubber stacks (gas treatment centers), and at potroom roof vents, respectively. Results indicate that roof vents are the primary PM_2.5 emitters (85% of all smelter emissions) and that 71% of all smelter PM_2.5 comes from CPM. In the second part, preliminary inorganic speciation studies are conducted by scanning electron microscopy–energy-dispersive X-ray analysis and by isotopic ratios to track smelter emissions to their surrounding environment. This paper releases the first speciation results for an aluminum smelter, and the preliminary isotopic ratio study indicates a 3% impact in terms of PM_2.5 emissions for a representative smelter in an urban area.

IMPLICATIONS Aluminum smelters tend to continuously improve their competitiveness by incrementally increasing production. In this context, assessing the effect of major contaminants is overriding, and ambient air modeling is often the preferred way to do so. Fine particles fit this category, and the primary aluminum industry needs to accurately know their emission factors to obtain representative modeling. Moreover, not all aluminum smelters have a method to measure PM_2.5 at roof vents, the primary emission outlets. Therefore, this paper describes the first-rate PM_2.5 measurement methods for aluminum smelter roof vents without down-comers. It also provides insight for environmental managers for tracking PM_2.5 emissions in plant surroundings.     

Participate and Gaseous Emissions from Natural Gas Furnaces and Water Heaters

Three furnaces and one hot water heater were tested for particulate and gaseous emissions. The effects of fuel, stoichiometry, operating conditions, and appliance type on emission levels were studied. The filterable particulate levels from a properly operating furnace were very low. However, condensable particulate emissions were considerably greater, approximately the same as predicted by EPA estimates of furnace particulate emissions. Carbon emissions comprised about 12% of filterable particulate emissions. However, when operated highly fuel-rich, copious amounts of elemental carbon particles were emitted with a mass median diameter of less than 0.4 μm. Gaseous emissions were dependent on cycling of the furnace and stoichiometry.

An estimate was made of the daily furnace emissions compared to daily emissions from a 1980 catalyst-equipped automobile. While gaseous emissions were less than the corresponding vehicle emissions, the particle emissions from the furnace were three times greater than particle emissions from a 1980 vehicle.     

PM2.5 emissions from aluminum smelters: coefficients and environmental impact

From 2004 to 2009, aiming to better understand implications for its smelters, Rio Tinto Alcan conducted a detailed study of PM2.5 and PM10 (particulate matter [PM] < or = 2.5 and 10 microm in aerodynamic diameter, respectively) in its facilities. This involved a two-level study: part 1, emission quantification; and part 2, assessment of aluminum smelter contribution to the surrounding environment. In the first part, U.S. Environmental Protection Agency Other Test Method (OTM) OTM27 and OTM28 are assessed as relevant and efficient methods for measuring fine particle emissions from aluminum smelter stacks. Rio Tinto Alcan has also developed a safe and robust method called CYCLEX to measure PM2.5 and condensable particulate matter (CPM) at the roof vents of potrooms. This work aims to determine the PM2.5 emission coefficients of 17, 55, and 417 g x t(-1) of aluminum produced (including CPM) in anode baking furnace exhaust (fume treatment center), at potroom scrubber stacks (gas treatment centers), and at potroom roof vents, respectively. Results indicate that roof vents are the primary PM2.5 emitters (85% of all smelter emissions) and that 71% of all smelter PM2.5 comes from CPM. In the second part, preliminary inorganic speciation studies are conducted by scanning electron microscopy-energy-dispersive X-ray analysis and by isotopic ratios to track smelter emissions to their surrounding environment. This paper releases the first speciation results for an aluminum smelter, and the preliminary isotopic ratio study indicates a 3% impact in terms of PM2.5 emissions for a representative smelter in an urban area.     

Assessment of elemental composition and properties of copper smelter-affected dust and its nano- and micron size fractions

A comprehensive approach has been developed to the assessment of composition and properties of atmospherically deposited dust in the area affected by a copper smelter. The approach is based on the analysis of initial dust samples, dynamic leaching of water soluble fractions in a rotating coiled column (RCC) followed by the determination of recovered elements and characterization of size, morphology and elemental composition of nano-, submicron, and micron par ticles of dust separated using field-flow fractionation in a RCC. Three separated size fractions of dust (<0.2, 0.2–2, and >2 μm) were characterized by static light scattering and scanning electron microscopy, whereupon the fractions were analyzed by ICP-AES and ICP-MS (after digestion). It has been evaluated that toxic elements, which are characteristics for copper smelter emissions (As, Cu, Zn), are accumulated in fraction >2 μm. At the same time, up to 2.4, 3.1, 8.2, 6.7 g/kg of As, Cu, Zn, Pb, correspondently, were found in nanoparticles (<0.2 μm). It has been also shown that some trace elements (Sn, Sb, Ag, Bi, and Tl) are accumulated in fraction <0.2, and their content in this fraction may be one order of magnitude higher than that in the fraction >2 μm, or the bulk sample. It may be assumed that Sn, Sb, Ag, Bi, Tl compounds are adsorbed onto the finest dust particles as compared to As, Cu, Zn compounds, which are directly emitted from the copper smelter as microparticles.

     

An analysis of the impact of the Sudbury smelters on wet and dry deposition in OntariO

Meteorological analyses of acidic deposition data were undertaken to quantify the effect of Sudbury emissions on precipitation quality and air quality in Ontario during the period 1980–1983 with particular emphasis on the Sudbury smelter shutdown period (July 1982–March 1983). The techniques used included air parcel trajectories and detailed meteorological analysis.Results indicate that the contribution of the Sudbury smelters to sulphate wet deposition in central and southern Ontario was small—less than 12 % of the wet deposition at the study sites. The smelter contribution to sulphur dry deposition was greater—possibly as high as 47 % of the total at Kapuskasing, and up to about 20–30% of the total in central Ontario, with a smaller contribution (less than 5 %) to the southwest and west of Sudbury. These percentages apply to the smelter emission rate in the early 1980s, i.e. about 0.9 million metric tons of SO₂ per year.     

Health Effects and Energy Choices

ABSTRACT

Day- and nighttime total suspended particulate matter was collected inside and outside Emperor Qin's Terra-Cotta Museum in winter and summer 2008. The purpose was to characterize the winter and summer differences of indoor airborne particles in two display halls with different architectural and ventilation conditions, namely the Exhibition Hall and Pit No. 1. The morphology and elemental composition of two season samples were investigated using scanning electron microscopy and energy dispersive X-ray spectrometry. It is found that the particle size, particle mass concentration, and particle type were associated with the visitor numbers in the Exhibition Hall and with the natural ventilation in Pit No. 1 in both winter and summer. Evident winter and summer changes in the composition and physicochemical properties of the indoor suspended particulate matters were related to the source emission and the meteorological conditions. Particle mass concentrations in both halls were higher in winter than in summer. In winter, the size of the most abundant particles at the three sites were all between 0.5 and 1.0 μm, whereas in summer the peaks were all located at less than 0.5 μm. The fraction of sulfur-containing particles was 2–7 times higher in winter than in summer. In addition to the potential soiling hazard, the formation and deposition of sulfur-containing particles in winter may lead to the chemical and physical weathering of the surfaces of the terra-cotta statues.

IMPLICATIONS Relatively few microanalyses of indoor airborne particles inside museums in China have been performed. The mass concentrations of winter and summer indoor total suspended particulate (TSP) are presented for the Emperor Qin's Terra-Cotta Museum along with the characterization of individual particles via computerized scanning electron microscopy and an energy dispersive X-ray spectrometry. The results indicate that both the high level of particle mass concentrations in winter and the predominant fine particles in summer were responsible for the soiling of the statues over a long period of time. The irreplaceable statues were also facing with weathering hazards posed by abundant sulfur-containing particles, especially in winter. Data provided in this study suggested that mechanical ventilation, air filtration, and air conditioning systems should be installed in Pit No. 1 display hall and proper display strategy should be adopted in Exhibition Hall.     

Estimation of Organic Compound Emissions from Waste Lagoons

Abstract

With the recent focus on fine particle matter (PM_2.5),new, self-consistent data are needed to characterize emissions from combustion sources. Such data are necessary for health assessment and air quality modeling. To address this need, emissions data for gas-fired combustors are presented here, using dilution sampling as the reference.The dilution method allows for collection of emitted particles under conditions simulating cooling and dilution during entry from the stack into the air. The sampling and analysis of the collected particles in the presence of precursor gases, SO₂, nitrogen oxide, volatile organic compound, and NH₃ is discussed; the results include data from eight gas fired units, including a dual-fuel institutional boiler and a diesel engine powered electricity generator. These data are compared with results in the literature for heavy-duty diesel vehicles and stationary sources using coal or wood as fuels. The results show that the gas-fired combustors have very low PM_2.5 mass emission rates in the range of ～10_-4 lb/million Btu (MMBTU) compared with the diesel backup generator with particle filter, with ～5 × 10_-3 lb/MMBTU. Even higher mass emission rates are found in coal-fired systems, with rates of ～0.07 lb/MMBTU for a bag-filter-controlled pilot unit burning eastern bituminous coal. The characterization of PM_2.5 chemical composition from the gas-fired units indicates that much of the measured primary particle mass in PM_2.5 samples is organic or elemental carbon and, to a much less extent, sulfate. Metal emissions are quite low compared with the diesel engines and the coal- or woodfueled combustors. The metals found in the gas-fired combustor particles are low in concentration, similar in concentration to ambient particles. The interpretation of the particulate carbon emissions is complicated by the fact that an approximately equal amount of particulate carbon (mainly organic carbon) is found on the particle collector and a backup filter. It is likely that measurement artifacts, mostly adsorption of volatile organic compounds on quartz filters, are positively biasing “true” particulate carbon emission results.     

Characterization of Airborne Dust from Two Nonferrous Foundries by Physico-chemical Methods and Multivariate Statistical Analyses

Abstract

Airborne particulate matter was sampled at a copper smelter and at an aluminum casting plant. Size, shape, quantity, and microlocalization of chemical species in the particulates were measured using closed cassettes, cascade impactors, scanning electron microscopy, X-ray diffraction, infrared and atomic absorption spectrophotometries, secondary ion mass spectrometry, and photoelectron spectroscopy. Cluster and principal components analyses were used in interpreting results. Aerosol chemistry varies as a function of size, and composition becomes more complex as the aerosol size drops into the respirable fraction and lower. Surface chemical properties are evidenced where, generally, volatile species are enriched. A few site-specific elements and characteristics were identified. The formation of particulates may often be related to process and practices, yet the actual distribution of species in the air remains an intricate matter.     

A revised estimate of copper emissions from road transport in UNECE-Europe and its impact on predicted copper concentrations

Comparisons of measured and model-predicted atmospheric copper concentrations show a severe underestimation of the observed concentrations by the models. This underestimation may be (partly) due to underestimated emissions of copper to air. Since the phase out of asbestos brake lining material, the composition of brake lining material has changed and may contain up to ∼15% copper. This makes brake wear from vehicles potentially an important source of atmospheric (particulate) copper concentrations. In this paper, we reassess the copper emissions due to exhaust emissions and brake wear from road transport. Overall, our reassessments result in an estimate of total copper emission to air in UNECE-Europe of 4.0–5.5 ktonnes yr⁻¹, which is substantially higher than the previous estimate of 2.8 ktonnes yr⁻¹. Copper concentrations over Europe are calculated with the LOTOS-EUROS model using the revised emission data as model input. The results show that the revised emission estimates are a major step towards gap closure of predicted versus observed copper concentrations in ambient air. Brake wear emissions may be responsible for 50–75% of the total copper emissions to air for most of Western Europe. The hypothesis that road transport is an important source of copper emissions is tested and confirmed by (1) reviewing available literature data of chemically speciated PM data from road tunnel studies and (2) the gradient observed in copper concentrations from ambient PM monitoring going from rural sites to street stations. The literature review and observational data suggest that the majority of the emitted PM10 brake wear particles is in the PM2.5–10 size range. The results of this study indicate that modification of brake lining composition is an important mitigation option to reduce copper exposure of the population in Western Europe.     

Size-resolved trace metal characterization of aerosols emitted by four important source types in Switzerland

In central Switzerland five types of emission sources are mainly responsible for airborne trace metals: traffic, industrial plants burning heavy oil, resuspension of soil particles, residential heatings and refuse incineration plants. The particulate emissions of each of these source types except refuse incineration were sampled using Berner impactors and the mass and elemental size distributions of Cd, Cu, Mn, Pb, Zn, As and Na determined.Cd, Na and Zn are not characteristic for any of these source types. As and Cu, occurring in the fine particle fractions are characteristic for heavy oil combustion, Mn for soil dust and sometimes for heavy and fuel oil combustion and Pb for traffic aerosols. The mass size distributions of aerosols originating from erosion and abrasion processes show a maximum mass fraction in the coarse particle range larger than about 1 μm aerodynamic equivalent diameters (A.E.D.). Aerosols originating from combustion processes show a second maximum mass fraction in the fine particle range below about 0.5μm A.E.D.Scanning electron microscopy combined with an EDS analyzer was used for the morphological characterization of emission and ambient aerosols.     

Is Levoglucosan a Suitable Quantitative Tracer for Wood Burning? Comparison with Receptor Modeling on Trace Elements in Lycksele,Sweden

Abstract

Particle emissions from residential wood combustion in small communities in Northern Sweden can sometimes increase the ambient particle concentrations to levels comparable to densely trafficked streets in the center of large cities. The reason for this is the combination of increased need for domestic heating during periods of low temperatures, leading to higher emission rates, and stable meteorological conditions. In this work, the authors compare two different approaches to quantify the wood combustion contribution to fine particles in Northern Sweden: a multivariate source-receptor analysis on inorganic compounds followed by multiple linear regression (MLR) of fine particle concentrations and levoglucosan used as a tracer. From the receptor model, it can be seen that residential wood combustion corresponds with 70% of modeled particle mass. Smaller contributions are also seen from local nonexhaust traffic particles, road dust, and brake wear (each contributing 14%). Of the mass, 1.5% is explained by long-distance transported particles, and 2% derives from a regional source deriving from either oil combustion or smelter activities.

In samples collected in ambient air, a significant linear correlation was found between wood burning particles and levoglucosan. The levoglucosan fraction in the ambient fine particulate matter attributed to wood burning according to the multivariate analysis ranged from <2% to 50%. This is much higher than the fraction found in the emission from the boilers expected to be responsible for most emissions at this site (between 3% and 6%). A laboratory emission study of wood and pellet boilers gave 0.3%_wt to 22%_wt levoglucosan to particle mass, indicating that the levoglucosan fraction may be highly dependent on combustion conditions, making it uncertain to use it as a quantitative tracer under real-world burning conditions. Thus, quantitative estimates of wood burning contributions will be very uncertain using solely levoglucosan as a tracer.     

Dilution-based emissions sampling from stationary sources: Part 2--Gas-fired combustors compared with other fuel-fired systems

With the recent focus on fine particle matter (PM2.5), new, self-consistent data are needed to characterize emissions from combustion sources. Such data are necessary for health assessment and air quality modeling. To address this need, emissions data for gas-fired combustors are presented here, using dilution sampling as the reference. The dilution method allows for collection of emitted particles under conditions simulating cooling and dilution during entry from the stack into the air. The sampling and analysis of the collected particles in the presence of precursor gases, SO2 nitrogen oxide, volatile organic compound, and NH3 is discussed; the results include data from eight gas fired units, including a dual-fuel institutional boiler and a diesel engine powered electricity generator. These data are compared with results in the literature for heavy-duty diesel vehicles and stationary sources using coal or wood as fuels. The results show that the gas-fired combustors have very low PM2.5 mass emission rates in the range of approximately 10(-4) lb/million Btu (MMBTU) compared with the diesel backup generator with particle filter, with approximately 5 x 10(-3) lb/MMBTU. Even higher mass emission rates are found in coal-fired systems, with rates of approximately 0.07 lb/MMBTU for a bag-filter-controlled pilot unit burning eastern bituminous coal. The characterization of PM2.5 chemical composition from the gas-fired units indicates that much of the measured primary particle mass in PM2.5 samples is organic or elemental carbon and, to a much less extent, sulfate. Metal emissions are quite low compared with the diesel engines and the coal- or wood-fueled combustors. The metals found in the gas-fired combustor particles are low in concentration, similar in concentration to ambient particles. The interpretation of the particulate carbon emissions is complicated by the fact that an approximately equal amount of particulate carbon (mainly organic carbon) is found on the particle collector and a backup filter. It is likely that measurement artifacts, mostly adsorption of volatile organic compounds on quartz filters, are positively biasing "true" particulate carbon emission results.     

The chemical composition of tropospheric aerosols and their contributing sources to a continental background site in northern Zimbabwe from 1994 to 2000

Atmospheric aerosols were collected in separate coarse (2–10 μm diameter) and fine (diameter less than 2 μm) size fractions at Rukomechi Research Station (16.1°S, 29.4°E), Zimbabwe, in the central part of southern Africa, from September 1994 to January 2000. The samples were analysed for the particulate mass (PM), black carbon, and 47 elements. The overall data set and the separate wet and dry season data sets were examined with absolute principal component analysis (APCA). Natural and anthropogenic aerosol sources were identified in both seasons, but the sources and their contributions to the total PM were found to vary between seasons and between size fractions. Crustal matter, sea salt (SS), a mixed biogenic (BIO) emission/biomass burning (BB) component, and a copper component were identified for the coarse aerosols during the wet season. APCA attributed 29% of the total wet season coarse PM to the mixed BIO/BB component, and 32% to SS. The copper component is likely due to the copper smelters in the Zambian Copperbelt. The dry season coarse PM originated from crustal matter, BB, BIO, and SS sources, with the major contribution (32%) coming from BB. Four components (crustal matter, BB, non-ferrous smelters, and SS) were identified for the fine particles for both the wet and dry seasons. The BB component provided the major contribution to the total fine PM, accounting for 44% and 79% in the wet and dry seasons, respectively. The relative contributions to the total PM (both fine and coarse) for all sources were greater in the dry season than the wet season, except for SS.     

Characterization of exhaust particles from military vehicles fueled with diesel,gasoline, and JP-8

Diluted exhaust from selected military aircraft ground-support equipment (AGE) was analyzed for particulate mass, elemental carbon (EC) and organic carbon (OC), SO4(2-), and size distributions. The experiments occurred at idle and load conditions and utilized a chassis dynamometer. The selected AGE vehicles operated on gasoline, diesel, and JP-8. These military vehicles exhibited concentrations, size distributions, and emission factors in the same range as those reported for nonmilitary vehicles. The diesel and JP-8 emission rates for PM ranged from 0.092 to 1.1 g/kg fuel. The EC contributed less and the OC contributed more to the particulate mass than reported in recent studies of vehicle emissions. Overall, the particle size distribution varied significantly with engine condition, with the number of accumulation mode particles and the count median diameter (CMD) increasing as engine load increased. The SO4(2-) analyses showed that the distribution of SO4(2-) mass mirrored the distribution of particle mass.     

Chemical characterization and source identification/apportionment of fine and coarse air particles in Thessaloniki,Greece

The distribution of air particulate mass and selected particle components (trace elements and polycyclic aromatic hydrocarbons (PAHs)) in the fine and the coarse size fractions was investigated at a traffic-impacted urban site in Thessaloniki, Greece. 76±6% on average of the total ambient aerosol mass was distributed in the fine size fraction. Fine-sized trace elemental fractions ranged between 51% for Fe and 95% for Zn, while those of PAHs were between 95% and 99%. A significant seasonal effect was observed for the size distribution of aerosol mass, with a shift to larger fine fractions in winter. Similar seasonal trend was exhibited by PAHs, whereas larger fine fractions in summer were shown by trace elements. The compositional signatures of fine and coarse particle fractions were compared to that of local paved-road dust. A strong correlation was found between coarse particles and road dust suggesting strong contribution of resuspended road dust to the coarse particles. A multivariate receptor model (multiple regression on absolute principal component scores) was applied on separate fine and coarse aerosol data for source identification and apportionment. Results demonstrated that the largest contribution to fine-sized aerosol is traffic (38%) followed by road dust (28%), while road dust clearly dominated the coarse size fraction (57%).     

On-road measurement of fine particle and nitrogen oxide emissions from light- and heavy-duty motor vehicles

An updated assessment of fine particle emissions from light- and heavy-duty vehicles is needed due to recent changes to the composition of gasoline and diesel fuel, more stringent emission standards applying to new vehicles sold in the 1990s, and the adoption of a new ambient air quality standard for fine particulate matter (PM_2.5) in the United States. This paper reports the measurement of emissions from vehicles in a northern California roadway tunnel during summer 1997. Separate measurements were made of uphill traffic in two tunnel bores: one bore carried both light-duty vehicles and heavy-duty diesel trucks, and the second bore was reserved for light-duty vehicles. Ninety-eight percent of the light-duty vehicles were gasoline-powered. In the tunnel, heavy-duty diesel trucks emitted 24, 37, and 21 times more fine particle, black carbon, and sulfate mass per unit mass of fuel burned than light-duty vehicles. Heavy-duty diesel trucks also emitted 15–20 times the number of particles per unit mass of fuel burned compared to light-duty vehicles. Fine particle emissions from both vehicle classes were composed mostly of carbon; diesel-derived particulate matter contained more black carbon (51±11% of PM_2.5 mass) than did light-duty fine particle emissions (33±4%). Sulfate comprised only 2% of total fine particle emissions for both vehicle classes. Sulfate emissions measured in this study for heavy-duty diesel trucks are significantly lower than values reported in earlier studies conducted before the introduction of low-sulfur diesel fuel. This study suggests that heavy-duty diesel vehicles in California are responsible for nearly half of oxides of nitrogen emissions and greater than three-quarters of exhaust fine particle emissions from on-road motor vehicles.     

Characterization of the Fugitive Particulate Emissions from Construction Mud/Dirt Carryout

Abstract

Although the fugitive dust associated with construction mud/dirt carryout can represent a substantial portion of the particulate matter (PM) emissions inventory in non-attainment areas, it has not been well characterized by direct sampling methods. In this paper, a research program is described that directly determined both PM₁₀ and PM_2.5 (particles ≤10 and 2.5 μm in classical aerodynamic diameter, respectively) emission factors for mud/dirt carryout from a major construction project located in metropolitan Kansas City, MO. The program also assessed the contribution of automotive emissions to the total PM_2.5 burden and determined the baseline emissions from the test road. As part of the study, both time-integrated and continuous exposure-profiling methods were used to assess the PM emissions, including particle size and elemental composition. This research resulted in overall PM₁₀ and PM_2.5 emission factors of 6 and 0.2 g/vehicle, respectively. Although PM₁₀ is within the range of prior U.S. Environmental Protection Agency (EPA) guidance, the PM_2.5 emission factor is far lower than previous estimates published by EPA. In addition, based on both the particle size and chemical data obtained in the study, a major portion of the PM_2.5 emissions appears to be attributable to automotive exhaust from light-duty, gasoline-powered vehicles and not to the fugitive dust associated with re-entrained mud/dirt carryout.     

Characterization of particulate emissions from Australian open-cut coal mines: Toward improved emission estimates

Given the significance of mining as a source of particulates, accurate characterization of emissions is important for the development of appropriate emission estimation techniques for use in modeling predictions and to inform regulatory decisions. The currently available emission estimation methods for Australian open-cut coal mines relate primarily to total suspended particulates and PM₁₀ (particulate matter with an aerodynamic diameter <10 μm), and limited data are available relating to the PM_2.5 (<2.5 μm) size fraction. To provide an initial analysis of the appropriateness of the currently available emission estimation techniques, this paper presents results of sampling completed at three open-cut coal mines in Australia. The monitoring data demonstrate that the particulate size fraction varies for different mining activities, and that the region in which the mine is located influences the characteristics of the particulates emitted to the atmosphere. The proportion of fine particulates in the sample increased with distance from the source, with the coarse fraction being a more significant proportion of total suspended particulates close to the source of emissions. In terms of particulate composition, the results demonstrate that the particulate emissions are predominantly sourced from naturally occurring geological material, and coal comprises less than 13% of the overall emissions. The size fractionation exhibited by the sampling data sets is similar to that adopted in current Australian emission estimation methods but differs from the size fractionation presented in the U.S. Environmental Protection Agency methodology. Development of region-specific emission estimation techniques for PM₁₀ and PM_2.5 from open-cut coal mines is necessary to allow accurate prediction of particulate emissions to inform regulatory decisions and for use in modeling predictions.

Implications: Development of region-specific emission estimation techniques for PM₁₀ and PM_2.5 from open-cut coal mines is necessary to allow accurate prediction of particulate emissions to inform regulatory decisions and for use in modeling predictions. Comprehensive air quality monitoring was undertaken, and corresponding recommendations were provided.     

Characterization of the fugitive particulate emissions from construction mud/dirt carryout

Although the fugitive dust associated with construction mud/dirt carryout can represent a substantial portion of the particulate matter (PM) emissions inventory in nonattainment areas, it has not been well characterized by direct sampling methods. In this paper, a research program is described that directly determined both PM10 and PM2.5 (particles < or =10 and 2.5 microm in classical aerodynamic diameter, respectively) emission factors for mud/dirt carryout from a major construction project located in metropolitan Kansas City, MO. The program also assessed the contribution of automotive emissions to the total PM2.5 burden and determined the baseline emissions from the test road. As part of the study, both time-integrated and continuous exposure-profiling methods were used to assess the PM emissions, including particle size and elemental composition. This research resulted in overall PM10 and PM2.5 emission factors of 6 and 0.2 g/vehicle, respectively. Although PM10 is within the range of prior U.S. Environmental Protection Agency (EPA) guidance, the PM2.5 emission factor is far lower than previous estimates published by EPA. In addition, based on both the particle size and chemical data obtained in the study, a major portion of the PM2.5 emissions appears to be attributable to automotive exhaust from light-duty, gasoline-powered vehicles and not to the fugitive dust associated with reentrained mud/dirt carryout.