Greenhouse gases emissions from a closed old landfill cultivated with biomass crops

Closed landfills need after-closure rehabilitation. The chosen option should ensure greenhouse gases release, from the landfill, is not promoted once settled. The objective of this study was to estimate and confront, during different seasons, CH₄, CO₂ and N₂O emissions under three vegetation covers in a closed landfill in Buenos Aires, Argentina. CH₄ (methane), CO₂ (carbon dioxide) and N₂O (nitrous oxide) emissions from landfill’s technosol under spontaneous vegetation (control), Pennisetum purpureum and Miscanthus giganteus (biomass crops), were quantified with non-steady-state non-flow-through chambers, in July 2014 and from February to July 2015. A linear regression analysis was performed to relate the variables “flux of a gas” and “concentration of that gas” from the 3 treatments and 6 dates, separating the 5 sampling times. A high correlation between concentrations and fluxes of CO₂ and N₂O was found, but no correlation was established for CH₄. Mean emissions (2014–2015) varied from: ?2.3 to 639.41 mgCH₄ m^?2 day^?1, 3884 to 46,365 mgCO₂ m^?2 day^?1 and 0.40 to 14.59 mgN₂O m^?2 day^?1. Vegetation covers had no significant effect on CH₄ and N₂O concentration in time, but they had on CO₂ concentration. Season of the year had a significant effect on concentration of the three gases. This is the first study on CH₄, CO₂ and N₂O emissions from a landfill closed 27 years ago covered with biomass crops.     

Carbon fluxes from coarse woody debris in southern taiga forests of the Valdai Upland

Studies in three typical forest biotopes of the Valdai Upland were performed to evaluate the stocks and surface area of coarse woody debris from spruce and birch (in linear transects), its colonization by xylotrophic fungi (during reconnaissance surveys), and CO₂ emission (by a chamber method). The stock and surface area were minimum in a paludal birch forest (46.4 m³/ha and 960 m²/ha) and maximum in a decay area of spruce forest (256.1 m³/ha and 3761 m²/ha, respectively). The assemblages of wood-decay fungi had a composition typically found in southern taiga forests. The total CO₂ flux varied from 145 kg C-CO₂/ha per year in the paludal birch forest to 462 kg C-CO₂/ha per year in small herb–green moss spruce forest. It is concluded that air temperature is an informative predictor of seasonal C-CO₂ flux rate from coarse woody debris.     

Greenhouse gas emissions from a semi-arid tropical reservoir in northeastern Brazil

We estimated carbon dioxide (CO₂) and methane (CH₄) emissions by diffusion, ebullition, and degassing in turbines from a semi-arid hydropower reservoir in northeastern Brazil. Sampling sites were allocated within the littoral and deeper waters of one embayment, the main-stream, and at turbines. Annual carbon emissions were estimated at 2.3?×?10⁵?±?7.45?×?10⁴ t C year^?1, or in CO₂-equivalents (CO₂-eq) at 1.33?×?10⁶?±?4.5?×?10⁵ t CO₂-eq year^?1. Diffusion across the water surface was the main pathway accounting for 96% of total carbon emissions. Ebullition was limited to littoral areas. A slight accumulation of CO₂, but not of CH₄, in bottom waters close to the turbines inlet led to degassing emissions about 8?×?10³ t C year^?1. Emissions in littoral areas were higher than in main-stream and contribute to 40% of the total carbon. Carbon (C) emissions per electricity generated, at 60% of installed capacity, is 0.05 t C-CO₂-eq MWh^?1. The ratio increases to 0.09 t C-CO₂ MWh^?1, equating 80% of the emissions from natural gas and 40% of diesel or coal power plants. Retention time and benthic metabolism were identified as main drivers for carbon emissions in littoral areas, while water column mixing and rapid water flow are important factors preventing CH₄ accumulation and loss by degassing. Our results indicate that Itaparica Reservoir, located in the semi-arid region of Northeastern Brazil, acts as a source of GHGs. Management measurements are needed to prevent emissions to raise in the future.     

The in-use annual energy and carbon saving by switching from a car to an electric bicycle in an urban UK general medical practice: the implication for NHS commuters

The UK Climate Change Act (CCA) mandates an 80 % reduction in CO₂ emissions by 2050. It is estimated that 3.2 M tonnes pa CO₂ results from travel-related NHS business. The acquisition of an electric bicycle to replace a car for both commuting and home visits allowed comparison of fuel use and CO₂ emissions over a 4-year period. The switch to the use of the electric bicycle reduced the average annual petrol use by 329 l, the energy consumption by 3,140 kWh and the CO₂ released by 748 kg a year. Wider adoption of electric bicycles in urban General Practice will contribute to the requirements of the CCA though to have a significant effect on the current estimated commuting-related carbon footprint of the NHS (0.76 MT pa) would require two-thirds of the workforce to abandon their cars in favour of electric bicycles.     

Solar-driven technology for freshwater production from atmospheric air by using the composite desiccant material “CaCl<Subscript>2</Subscript>/floral foam”

In this communication, experiments have been performed to check the capability of the newly formed composite desiccant material (CaCl₂/floral) for the extraction of freshwater from atmospheric air. Three numbers of solar glass desiccant box type system (SGDBS) with a captured area of 0.36 m² each, have been used. The design parameters for the water production are height of glass from desiccant bed at 0.22 m, inclination in angle as 30°, the effective thickness of glass as 3 mm and number of glazing as single. The maximum yield by the new composite desiccant material is 0.35 ml/cm³/day. The efficiency of the system SGDBS with 37 % concentration of CaCl₂ is 76.44 %.     

Energy, environment and growth nexus in South Asia

The present study investigates the energy, environment and growth nexus for a panel of South Asian countries including Bangladesh, India, Pakistan, Sri Lanka and Nepal. The simultaneous analysis of real GDP, energy consumption and CO₂ emissions is conducted for the period 1980–2010. Levin panel unit root test and Im test panel unit root both indicate that all the variables are I (1). In addition, Kao’s panel Cointegration test specifies a stable long-term relationship between all these variables. Empirical findings show that a 1 % increase in energy consumption increases output by 0.81 % in long run whereas for the same increase in CO₂ emission output falls by 0.17 % in long run. Panel Granger causality tests report short-run causality running from energy consumption to CO₂ emissions and from CO₂ emissions to GDP.     

The use of biomass production and allometric models to estimate carbon sequestration of <Emphasis Type="Italic">Jatropha curcas</Emphasis> L. plantations in western Burkina Faso

The topic of carbon sequestration in plants has received much attention recently due to concerns about global climate change, which is being exacerbated by deforestation. In the early days of the global bioenergy boom, the private sector and non-government organizations enthusiastically promoted the planting of Jatropha curcas L. as a key candidate shrub species for the production of bioenergy in West Africa. This study investigates the aboveground biomass production and carbon sequestration potential of J. curcas, which is already widely cultivated for the production of oil seeds, biodiesel and biokerosene. The specific objective is to use a destructive method to develop allometric prediction equations of the aboveground biomass production of J. curcas plantations. 38 J. curcas shrubs were harvested and weighed in order to estimate biomass production. These data were used to develop allometric equations for the estimation of wood, leaf and total aboveground biomass production. The best-fit models found for estimating shrub component biomass and total aboveground biomass production were of the power form. All of the regression equations relating the prediction of leaf biomass, wood biomass and total aboveground biomass with J. curcas diameter at 20 cm above the ground (D) were statistically significant (p < 0.001) and also presented the highest goodness of fit (high R ²). The aboveground biomass carbon content was estimated using the ash method. Carbon content in leaves and wood was, respectively, 48 and 54 %. The current established allometric equations can be helpful to provide a rapid estimation of the aboveground biomass and C stock for J. curcas biofuel projects in semi-arid conditions.     

Life cycle inventory of the commercial production of compost from oil palm biomass: a case study

This paper compared the life cycle inventory (LCI) obtained from three commercial oil palm biomass composting projects in Malaysia which use the open windrow composting system. The LCI was obtained and calculated based on the functional unit of 1 t of compost produced. The input of the inventory are the feed materials such as empty fruit bunches (EFB) and palm oil mill effluent (POME); and utilities which include electricity generated at palm oil mill and diesel used. Composting 2.0–2.5 t of EFB and 5.0–7.5 t of POME required diesel from 218.7 to 270.2 MJ and electricity from 0 to 6.8 MJ. It is estimated that the composting emitted from 0.01 to 0.02 t CO_2eq/t_compost mainly from diesel used to operate machineries. Composting saved 65 % of time required for a complete degradation of POME when compared to ponding system, and 89 % of time required for a complete degradation of EFB compared to mulching. In terms of land required, it required 36 % less land as compared to ponding for POME and 99 % less land as compared to mulching for EFB. Based on the case study, diesel was found to be the main contributor to the environmental impact. There is a potential of upgrading the process to be more economical and environmental friendly. Using electricity as the source of energy has a lower footprint for the composting process. Instead of using raw POME, studies had reported that using treated POME either from anaerobic ponding or digested tank can accelerate the composting process.     

Direct N2O emission from agricultural soils in Poland between 1960 and 2009

Nitrogen fertilization (N) is commonly known as a main source of direct nitrous oxide (N₂O) emission from agricultural soils. An area of 38 % of the total land surface of Poland was covered by agricultural soils in 2009. In this paper, we aimed at analyzing data regarding the land exploitation for 13 selected subareas of Poland between 1960 and 2009. Seven out of the 13 subareas studied are located in the West (area A), and six subareas are located in southeast of Poland (area B). The total area covered by large farms (>20 ha) differed largely, between area A (10.6 %) and area B (0.9 %) in 2009. Both areas varied in terms of the amount of fertilizers used annually, average crop yield and crop structure. Average direct emissions of N₂O from agricultural soils were 1.66 ± 0.09 kg N₂O–N ha^?1 a^?1 for area A, 1.39 ± 0.07 kg N₂O–N ha^?1 a^?1 for area B and 1.46 ± 0.07 kg N₂O–N ha^?1 a^?1 for the whole country between 1960 and 2009.     

A laboratory study on CO2 emission from asphalt binder and its reduction with the use of warm mix asphalt

Oxidation of hydrocarbon in asphalt binder leads to the production of carbon dioxide (CO₂) during the production of hot mix asphalt. The objective of this laboratory study was to investigate the effects of the asphalt additive Sasobit^®, asphalt content and mixing/placement temperature on CO₂ emissions from binder with laboratory measurements. The isolated effects of Sasobit on asphalt absorption into the aggregate were also looked at. Temperature was found to be the only statistically significant factor on emissions. This would suggest that warm mix asphalt technology, which employs the use of Sasobit in asphalt mixtures, is a very effective way of lowering the industry's CO₂ emission impact, both directly and by the use of less energy for heating. This work predicts that greater than 30% reduction of CO₂ emissions is possible with typically used levels of Sasobit.     

Dividivi tannins: an ecological product for water-based drilling fluids

Modified tannins are used as deflocculant additives in the formulation of water-based drilling fluids (WBDF) for drilling operations in any scenario. Due to their high heavy metals content, these additives are toxic and hazardous for any environmental scenario. Deflocculant efficiency of unmodified tannins (UDT) extracted from fruit pods of “dividivi” (Caesalpinia coriaria) as an additive for WBDF was assessed. Raw materials for UDT elaboration come from the rural and sustainable exploitation of natural occurring dividivi trees, growing in dry tropical forests in Anzoátegui state (Orinoco Oil Belt, eastern Venezuela). The tannins extract, in the form of dividivi fruit powder, contains 47.0 % of total tannins (hydrolyzable tannins plus condensed tannins), of which 67.4 % corresponds to hydrolyzable tannins. Dividivi tannins in WBDF showed nine (9) times deflocculant efficiency than heavy metals commercial modified tannins. Moreover, commercial modified tannins do not improve their deflocculant efficiency with increased tannin content. Ecotoxicological studies were carried out for WBDF formulations with UDT, using freshwater microalgae Scenedesmus dimorphus as chronic toxicity bioindicator. Toxicity bioassays performed with these microalgae did not show significant effects on its population growth. The EC₅₀ values resulted in over 100,000 mg L^?1, and these formulations were therefore considered non-toxic. Values of LC₅₀ obtained this time with Poecilia reticulata, as acute toxicity bioindicator are around 100,000 mg L^?1, with no significant effects on population mortality. Thus, WBDF formulated with UDT can be considered non-toxic formulations for populations of this freshwater fish. From the social perspective, the use of UDT in WBDF fosters organized communities economical activities based on the maintenance of a sustainable supply chain for processing fruits in a quantity enough to obtain three thousand seven hundred fifty kilograms (3750 Kg). The UDT so obtained was used as deflocculant in four (4) oil wells producing excellent performance and relevant savings compared with commercial modified tannin.     

Properties of alkali-activated fly ash: high performance to lightweight

Alkali ash material (AAM) concrete is a unique material that is sustainable and cost-effective because it utilises waste fly ash, and has properties superior to other concrete products. The AAM concrete described here is produced from the addition of inexpensive chemicals to fly ash. AAM can be used to create a wide range of materials including high performance concrete (HPC-AAM) and lightweight (LW-AAM). The high performance AAM provides rapid strength gain along with high ultimate strengths of more than 110 MPa (16000 psi). LW-AAM can produce materials with densities ranging from 1200 to 2200 kg/m³ and compressive strengths from 2 (290 psi) to 65 MPa (9500 psi). Both HPC-AAM and LW-AAM have far better environmental resistance than Portland cement concrete, resisting attack from sulphuric acid (H₂SO₄), hydrochloric acid (HCl) and organic acids. AAMs resists freeze–thaw attack and high abrasion, possesses low chloride permeability and does not exhibit alkali silica reactivity.     

Feasibility of PV–biodiesel hybrid energy system for a cement technology institute in India

This paper compares an existing unreliable grid supply with a proposed PV–biodiesel hybrid energy system in order to find the feasibility of the latter for improvement in reliability of power supply, lower pollutant emissions and saving of coal reserves. In the present study, the electrical load of a cement technology institute located in Bhilai, India, has been selected for the purpose of analysis. The results show that hybrid PV–biodiesel system comprising 25 kW PV array, 8 kW biodiesel generator-1, 20 kW biodiesel generator-2, 10 kW inverter and 10 kW rectifier will supply power to the institute avoiding addition of 27.744 tons of CO₂ in atmosphere and save 55,080 kg of coal per year with improvement in reliability from 93.15 to 100%.     

Energy and land use in worldwide agriculture: an application of life cycle energy and cluster analysis

Agriculture is expected to provide food in a sustainable manner while also partially contributing to the energy problem as well as to bio-material supply. Moreover, fossil fuels scarcity calls for an increase of energy efficiency in agricultural processes. This study evaluates patterns, trends, driving factors and trade-offs of energy use in selected agricultural systems and aims at grouping them into clusters with similar energy and social performances. Results show that in 2010 the highest power densities and energy intensities of production are found by crop sector of cluster 5 (China: 59.19 GJ/ha, 15.29 MJ/kg dm) and cluster 3 (Japan: 50.11 GJ/ha, 12.32 MJ/kg dm) as well as by livestock sector of cluster 3 (Japan: 328.47 GJ/ha, 103.08 MJ/kg dm), while the lowest values in clusters 2 and 4, including selected developing countries and USA. Cluster 3 (Japan) also shows the lowest energy intensity of economic value of crops (2.75 MJ/$), while cluster 5 (China) the highest one (23.96 MJ/$). Cluster analysis also sheds light on trends, identifying two groups: cluster 1*, gathering most European countries, USA and Japan, characterized by a decreasing trend of all energy indicators; and cluster 2*, including developing countries, the Netherlands and Spain, characterized by an increasing trend of indicators. Results highlight the importance of an integrated framework for evaluating energy use as well as of a multi-criteria approach to understand the trade-offs and interplay of performance indicators.     

Characteristics of PM10, PM2.5, CO2 and CO monitored in interiors and platforms of subway train in Seoul, Korea

This study was performed to investigate the concentration of PM₁₀ and PM_2.5 inside trains and platforms on subway lines 1, 2, 4 and 5 in Seoul, KOREA. PM₁₀, PM_2.5, carbon dioxide (CO₂) and carbon monoxide (CO) were monitored using real-time monitoring instruments in the afternoons (between 13:00 and 16:00). The concentrations of PM₁₀ and PM_2.5 inside trains were significantly higher than those measured on platforms and in ambient air reported by the Korea Ministry of Environment (Korea MOE). This study found that PM₁₀ levels inside subway lines 1, 2 and 4 exceeded the Korea indoor air quality (Korea IAQ) standard of 150 μg/m³. The average percentage that exceeded the PM₁₀ standard was 83.3% on line 1, 37.9% on line 2 and 63.1% on line 4, respectively. PM_2.5 concentration ranged from 77.7 μg/m³ to 158.2 μg/m³, which were found to be much higher than the ambient air PM_2.5 standard promulgated by United States Environmental Protection Agency (US-EPA) (24 h arithmetic mean: 65 μg/m³). The reason for interior PM₁₀ and PM_2.5 being higher than those on platforms is due to subway trains in Korea not having mechanical ventilation systems to supply fresh air inside the train. This assumption was supported by the CO₂ concentration results monitored in tube of subway that ranged from 1153 ppm to 3377 ppm. The percentage of PM_2.5 in PM₁₀ was 86.2% on platforms, 81.7% inside trains, 80.2% underground and 90.2% at ground track. These results indicated that fine particles (PM_2.5) accounted for most of PM₁₀ and polluted subway air. GLM statistical analysis indicated that two factors related to monitoring locations (underground and ground or inside trains and on platforms) significantly influence PM₁₀ (p < 0.001, R² = 0.230) and PM_2.5 concentrations (p < 0.001, R² = 0.172). Correlation analysis indicated that PM₁₀, PM_2.5, CO₂ and CO were significantly correlated at p < 0.01 although correlation coefficients were different. The highest coefficient was 0.884 for the relationship between PM₁₀ and PM_2.5.     

Energy analysis for onsite and offsite suburban wastewater

The environmental consequence of meeting the planet’s energy requirements has shown that biological degradation of organic constituent from wastewater does not only produces biogas. It also produces flammable methane that has 21 times more global warming potential or greenhouse effect than carbon dioxide. This becomes a loss of potential renewable energy when it is flared. This study investigates recoverable energy from cassava wastewater and effect of unrecovered onsite (not from treatment plant) wastewater energy. Sludge from both onsite untreated and offsite treated wastewater from a cassava processing station in a sub urban community of Nigeria was analyzed. The result shows that the offsite treatment has a methane potential of 27.428 m³/day compared to the onsite methane emission potential with 17.807 m³/day. The onsite 17.807 m³/day of methane is equivalent to 0.126 kgCH₄/year of emitted methane base on industrial procedure standards by the IPCC (2006) guidelines for national greenhouse gas inventories. An additional 54.03% of methane will be recovered if the onsite emissions were to be captured . At an emission efficiency of 0.025 kgCH₄/kg COD, the untreated wastewater indicates a potential contribution to the greenhouse effect. A mathematical model analysis was presented for ease in determining the amount of methane emitted from the untreated wastewater. This study support suggested methodologies and previous work comparing anaerobic offsite methane potential and untreated wastewater methane emission potentials along with its greenhouse effects.     

Estimating the effect of nitrogen fertilizer on the greenhouse gas balance of soils in Wales under current and future climate

The Welsh Government is committed to reduce greenhouse gas (GHG) emissions from agricultural systems and combat the effects of future climate change. In this study, the ECOSSE model was applied spatially to estimate GHG and soil organic carbon (SOC) fluxes from three major land uses (grass, arable and forest) in Wales. The aims of the simulations were: (1) to estimate the annual net GHG balance for Wales; (2) to investigate the efficiency of the reduced nitrogen (N) fertilizer goal of the sustainable land management scheme (Glastir), through which the Welsh Government offers financial support to farmers and land managers on GHG flux reduction; and (3) to investigate the effects of future climate change on the emissions of GHG and plant net primary production (NPP). Three climate scenarios were studied: baseline (1961–1990) and low and high emission climate scenarios (2015–2050). Results reveal that grassland and cropland are the major nitrous oxide (N₂O) emitters and consequently emit more GHG to the atmosphere than forests. The overall average simulated annual net GHG balance for Wales under baseline climate (1961–1990) is equivalent to 0.2 t CO₂e ha^?1 y^?1 which gives an estimate of total annual net flux for Wales of 0.34 Mt CO₂e y^?1. Reducing N fertilizer by 20 and 40 % could reduce annual net GHG fluxes by 7 and 25 %, respectively. If the current N fertilizer application rate continues, predicted climate change by the year 2050 would not significantly affect GHG emissions or NPP from soils in Wales.     

Assessment of physicochemical characteristics of Ganga Canal water quality in Uttarakhand

Assessment of physicochemical parameters of Ganga Canal water was carried out during 2012–2013 at Haridwar (Uttarakhand) with two different sites, i.e., Bhimgoda Barrage (site 1—control site) and Bahadrabad (site 2—contaminated site), where canal water flows with loads of pollution from highly commercial and industrial areas. During investigation, maximum turbidity (287.72 ± 56.28 JTU), total solids (1167.60 ± 303.90 mg l^?1), free CO₂ (1.88 ± 0.22 mg l^?1), total hardness (60.14 ± 1.13 mg l^?1), pH (7.1 ± 0.13), nitrate (0.048 ± 0.010), nitrite (0.019 ± 0.001), biochemical oxygen demand (2.866 ± 1.098), chemical oxygen demand (6.8 ± 2.61) and phosphate (0.087 ± 0.015), while minimum velocity (1.71 ± 0.19 ms^?1), transparency (0.12 ± 0.08 m) and dissolved oxygen (7.95 ± 0.44 mg l^?1) were recorded in monsoon season at site 2 in comparison with site 1. The mean values of these parameters were compared with WHO and ISI standards and found significant differences (p < 0.05) in the mean values of turbidity, total solids, pH, dissolved oxygen, free CO₂ and total hardness with sampling sites. The turbidity of both the sites 1 and 2 was recorded above the permissible limit. Turbidity of site 2 is much higher than of site 1, so it is counted as more polluted. The values of the studied parameters were more during monsoon season and summer season at site 2 as compared to site 1. The results indicated that most of the physicochemical parameters from Ganga Canal system were within or at periphery in comparison with permissible limit of ISI and WHO for drinking water and therefore may be suitable for domestic purposes, but it requires perceptible consideration due to intense changes in climate and increase in pollution.     

Sulfide production during anaerobic lagoon treatment of tapioca wastewater

Laboratory-scale experiments on anaerobic lagoon treatment of tapioca wastewater were conducted under ambient, tropical conditions. The objectives of this study were to investigate factors that affect hydrogen sulfide production and to propose means to control the formation of hydrogen sulfide in lagoon effluents. The concentrations of sulfides were found to increase with increasing organic loading from 2.76 to 5.77 kg COD/m³.d, decreasing hydraulic retention time; and increasing pH from 3 to 7. The maximum total sulfide concentration of 18.8 mg/L occurred at the organic loading of 5.77 kg COD/ m³.d and neutral pH. the maximum H₂S concentration was calculated to be 13.3 mg/L which occurred in the laggoon operated at an organic loading of 5.77 kg COD/m³.d and a pH of 5. The control of odour problems due to the H₂S formation should be possible by raising pH of the lagoon water to be more than 8 or operating the lagoon at low organic loadings.     

Human well-being, the global emissions debt, and climate change commitment

Energy consumption is fundamentally necessary for human well-being. However, although increasing energy consumption provides substantial improvements in well-being for low and intermediate levels of development, incremental increases in consumption fail to provide improvements for “super-developed” countries that exhibit the highest levels of development and energy consumption. The aim of this note is, therefore, to quantitatively explore the global emissions debt and climate change commitment associated with the gap in energy consumption between the energy-saturated super-developed countries and the rest of the world. Adopting Kates’ identity, I calculate that elevating the current populations in the non-super-developed countries to the energy and carbon intensities of the United States is akin to adding the fossil-fuel CO₂ emissions of more than 15 United States to the global annual total, implying cumulative emissions of almost 4000 GT CO₂ from 2010 through 2050. The inevitability of continued emissions beyond 2050 suggests that the transition of non-super-developed countries to a US-like profile between now and 2050 could, by itself, plausibly result in global warming of 3.2 °C above the late-twentieth century baseline, including an extremely high likelihood that global warming would exceed 1.2 °C. Global warming of this magnitude is likely to cause regional climate change that falls well outside of the baseline variations to which much of the world is presently accustomed, meaning that a US-like energy-development pathway carries substantial climate change commitment for both non-super-developed and super-developed countries, independent of future emissions from the super-developed world. However, the assumption that all countries converge on the minimum energy intensity of the super-developed world and a carbon-free energy system between now and 2050 implies cumulative CO₂ emissions of less than 1000 GT CO₂ between 2010 and 2050, along with a less than 40 % probability of exceeding 1.2 °C of additional global warming. It is, therefore, possible that intensive efforts to develop and deploy global-scale capacity for low-carbon energy consumption could simultaneously ensure human well-being and substantially limit the associated climate change commitment.