A coupled THC model of the FEBEX in situ test with bentonite swelling and chemical and thermal osmosis

The performance assessment of a geological repository for radioactive waste requires quantifying the geochemical evolution of the bentonite engineered barrier. This barrier will be exposed to coupled thermal (T), hydrodynamic (H), mechanical (M) and chemical (C) processes. This paper presents a coupled THC model of the FEBEX (Full-scale Engineered Barrier EXperiment) in situ test which accounts for bentonite swelling and chemical and thermal osmosis. Model results attest the relevance of thermal osmosis and bentonite swelling for the geochemical evolution of the bentonite barrier while chemical osmosis is found to be almost irrelevant. The model has been tested with data collected after the dismantling of heater 1 of the in situ test. The model reproduces reasonably well the measured temperature, relative humidity, water content and inferred geochemical data. However, it fails to mimic the solute concentrations at the heater-bentonite and bentonite-granite interfaces because the model does not account for the volume change of bentonite, the CO(2)(g) degassing and the transport of vapor from the bentonite into the granite. The inferred HCO(3)(-) and pH data cannot be explained solely by solute transport, calcite dissolution and protonation/deprotonation by surface complexation, suggesting that such data may be affected also by other reactions.     

Reactive transport modelling of biogeochemical processes and carbon isotope geochemistry inside a landfill leachate plume

The biogeochemical processes governing leachate attenuation inside a landfill leachate plume (Banisveld, the Netherlands) were revealed and quantified using the 1D reactive transport model PHREEQC-2. Biodegradation of dissolved organic carbon (DOC) was simulated assuming first-order oxidation of two DOC fractions with different reactivity, and was coupled to reductive dissolution of iron oxide. The following secondary geochemical processes were required in the model to match observations: kinetic precipitation of calcite and siderite, cation exchange, proton buffering and degassing. Rate constants for DOC oxidation and carbonate mineral precipitation were determined, and other model parameters were optimized using the nonlinear optimization program PEST by means of matching hydrochemical observations closely (pH, DIC, DOC, Na, K, Ca, Mg, NH4, Fe(II), SO4, Cl, CH4, saturation index of calcite and siderite). The modelling demonstrated the relevance and impact of various secondary geochemical processes on leachate plume evolution. Concomitant precipitation of siderite masked the act of iron reduction. Cation exchange resulted in release of Fe(II) from the pristine anaerobic aquifer to the leachate. Degassing, triggered by elevated CO2 pressures caused by carbonate precipitation and proton buffering at the front of the plume, explained the observed downstream decrease in methane concentration. Simulation of the carbon isotope geochemistry independently supported the proposed reaction network.     

Inverse modeling of multicomponent reactive transport through single and dual porosity media

Compacted bentonite is foreseen as buffer material for high-level radioactive waste in deep geological repositories because it provides hydraulic isolation, chemical stability, and radionuclide sorption. A wide range of laboratory tests were performed within the framework of FEBEX (Full-scale Engineered Barrier EXperiment) project to characterize buffer properties and develop numerical models for FEBEX bentonite. Here we present inverse single and dual-continuum multicomponent reactive transport models of a long-term permeation test performed on a 2.5 cm long sample of FEBEX bentonite. Initial saline bentonite porewater was flushed with 5.5 pore volumes of fresh granitic water. Water flux and chemical composition of effluent waters were monitored during almost 4 years. The model accounts for solute advection and diffusion and geochemical reactions such as aqueous complexation, acid-base, cation exchange, protonation/deprotonation by surface complexation and dissolution/precipitation of calcite, chalcedony and gypsum. All of these processes are assumed at local equilibrium. Similar to previous studies of bentonite porewater chemistry on batch systems which attest the relevance of protonation/deprotonation on buffering pH, our results confirm that protonation/deprotonation is a key process in maintaining a stable pH under dynamic transport conditions. Breakthrough curves of reactive species are more sensitive to initial porewater concentration than to effective diffusion coefficient. Optimum estimates of initial porewater chemistry of saturated compacted FEBEX bentonite are obtained by solving the inverse problem of multicomponent reactive transport. While the single-continuum model reproduces the trends of measured data for most chemical species, it fails to match properly the long tails of most breakthrough curves. Such limitation is overcome by resorting to a dual-continuum reactive transport model.     

Long-term geochemical evolution of the near field repository: insights from reactive transport modelling and experimental evidences

The KBS-3 underground nuclear waste repository concept designed by the Swedish Nuclear Fuel and Waste Management Co. (SKB) includes a bentonite buffer barrier surrounding the copper canisters and the iron insert where spent nuclear fuel will be placed. Bentonite is also part of the backfill material used to seal the access and deposition tunnels of the repository. The bentonite barrier has three main safety functions: to ensure the physical stability of the canister, to retard the intrusion of groundwater to the canisters, and in case of canister failure, to retard the migration of radionuclides to the geosphere. Laboratory experiments (< 10 years long) have provided evidence of the control exerted by accessory minerals and clay surfaces on the pore water chemistry. The evolution of the pore water chemistry will be a primordial factor on the long-term stability of the bentonite barrier, which is a key issue in the safety assessments of the KBS-3 concept.In this work we aim to study the long-term geochemical evolution of bentonite and its pore water in the evolving geochemical environment due to climate change. In order to do this, reactive transport simulations are used to predict the interaction between groundwater and bentonite which is simulated following two different pathways: (1) groundwater flow through the backfill in the deposition tunnels, eventually reaching the top of the deposition hole, and (2) direct connection between groundwater and bentonite rings through fractures in the granite crosscutting the deposition hole. The influence of changes in climate has been tested using three different waters interacting with the bentonite: present-day groundwater, water derived from ice melting, and deep-seated brine. Two commercial bentonites have been considered as buffer material, MX-80 and Deponit CA-N, and one natural clay (Friedland type) for the backfill. They show differences in the composition of the exchangeable cations and in the accessory mineral content. Results from the simulations indicate that pore water chemistry is controlled by the equilibrium with the accessory minerals, especially carbonates. pH is buffered by precipitation/dissolution of calcite and dolomite, when present. The equilibrium of these minerals is deeply influenced by gypsum dissolution and cation exchange reactions in the smectite interlayer. If carbonate minerals are initially absent in bentonite, pH is then controlled by surface acidity reactions in the hydroxyl groups at the edge sites of the clay fraction, although its buffering capacity is not as strong as the equilibrium with carbonate minerals. The redox capacity of the bentonite pore water system is mainly controlled by Fe(II)-bearing minerals (pyrite and siderite). Changes in the groundwater composition lead to variations in the cation exchange occupancy, and dissolution–precipitation of carbonate minerals and gypsum. The most significant changes in the evolution of the system are predicted when ice-melting water, which is highly diluted and alkaline, enters into the system. In this case, the dissolution of carbonate minerals is enhanced, increasing pH in the bentonite pore water. Moreover, a rapid change in the population of exchange sites in the smectite is expected due to the replacement of Na for Ca.     

Numerical simulation of reactive processes in an experiment with partially saturated bentonite

Bentonites are preferred materials for use as engineered barriers for high-level nuclear waste repositories. Simulation of geochemical processes in bentonite is therefore important for long-term safety assessment of those repositories. In this work, the porewater chemistry of a bentonite sample subject to simultaneous heating and hydration, as studied by Cuevas et al. [Cuevas, J., Villar, M., Fernández, A., Gómez, P., Martín, P., 1997. Porewaters extracted from compacted bentonite subjected to simultaneous heating and hydration. Applied Geochemistry 12, 473-481.], was assessed with a non-isothermal reactive transport model by coupling the geochemical software PHREEQC2 with the object-oriented FEM simulator GeoSys/RockFlow. Reactive transport modelling includes heat transport, two-phase flow, multicomponent transport and geochemical reactions in the liquid phase, i.e. ion exchange, mineral dissolution/precipitation and equilibrium reactions. Simulations show that the easily soluble minerals in bentonite determine the porewater chemistry. Temperature affects both two-phase flow and geochemical reactions. Porosity change due to dissolution/precipitation is low during the experiment. However, changes of the effective porosity caused by bentonite swelling can be very large. The simulated results agree well with the experimental data.     

Biogeochemistry and isotope geochemistry of a landfill leachate plume

The biogeochemical processes were identified which improved the leachate composition in the flow direction of a landfill leachate plume (Banisveld, The Netherlands). Groundwater observation wells were placed at specific locations after delineating the leachate plume using geophysical tests to map subsurface conductivity. Redox processes were determined using the distribution of solid and soluble redox species, hydrogen concentrations, concentration of dissolved gases (N(2), Ar, and CH(4)), and stable isotopes (delta15N-NO(3), delta34S-SO(4), delta13C-CH(4), delta2H-CH(4), and delta13C of dissolved organic and inorganic carbon (DOC and DIC, respectively)). The combined application of these techniques improved the redox interpretation considerably. Dissolved organic carbon (DOC) decreased downstream in association with increasing delta13C-DOC values confirming the occurrence of degradation. Degradation of DOC was coupled to iron reduction inside the plume, while denitrification could be an important redox process at the top fringe of the plume. Stable carbon and hydrogen isotope signatures of methane indicated that methane was formed inside the landfill and not in the plume. Total gas pressure exceeded hydrostatic pressure in the plume, and methane seems subject to degassing. Quantitative proof for DOC degradation under iron-reducing conditions could only be obtained if the geochemical processes cation exchange and precipitation of carbonate minerals (siderite and calcite) were considered and incorporated in an inverse geochemical model of the plume. Simulation of delta13C-DIC confirmed that precipitation of carbonate minerals happened.     

DOC removal paradigms in highly humic aquatic ecosystems

Background, aim, and scope  Dissolved humic substances (HS) usually comprise 50–80% of the dissolved organic carbon (DOC) in aquatic ecosystems. From a trophic and biogeochemical perspective, HS has been considered to be highly refractory and is supposed to accumulate in the water. The upsurge of the microbial loop paradigm and the studies on HS photo-degradation into labile DOC gave rise to the belief that microbial processing of DOC should sustain aquatic food webs in humic waters. However, this has not been extensively supported by the literature, since most HS and their photo-products are often oxidized by microbes through respiration in most nutrient-poor humic waters. Here, we review basic concepts, classical studies, and recent data on bacterial and photo-degradation of DOC, comparing the rates of these processes in highly humic ecosystems and other aquatic ecosystems. Materials and methods  We based our review on classical and recent findings from the fields of biogeochemistry and microbial ecology, highlighting some odd results from highly humic Brazilian tropical lagoons, which can reach up to 160 mg C L⁻¹. Results and discussion  Highly humic tropical lagoons showed proportionally lower bacterial production rates and higher bacterial respiration rates (i.e., lower bacterial growth efficiency) than other lakes. Zooplankton showed similar δ¹³C to microalgae but not to humic DOC in these highly humic lagoons. Thus, the data reviewed here do not support the microbial loop as an efficient matter transfer pathway in highly humic ecosystems, where it is supposed to play its major role. In addition, we found that some tropical humic ecosystems presented the highest potential DOC photo-chemical mineralization (PM) rates reported in the literature, exceeding up to threefold the rates reported for temperate humic ecosystems. We propose that these atypically high PM rates are the result of a joint effect of the seasonal dynamics of allochthonous humic DOC input to these ecosystems and the high sunlight incidence throughout the year. The sunlight action on DOC is positive to microbial consumption in these highly humic lagoons, but little support is given to the enhancement of bacterial growth efficiency, since the labile photo-chemical products are mostly respired by microbes in the nutrient-poor humic waters. Conclusions  HS may be an important source of energy for aquatic bacteria in humic waters, but it is probably not as important as a substrate to bacterial growth and to aquatic food webs, since HS consumption is mostly channeled through microbial respiration. This especially seems to be the case of humic-rich, nutrient-poor ecosystems, where the microbial loop was supposed to play its major role. Highly humic ecosystems also present the highest PM rates reported in the literature. Finally, light and bacteria can cooperate in order to enhance total carbon degradation in highly humic aquatic ecosystems but with limited effects on aquatic food webs. Recommendations and perspectives  More detailed studies using C- and N-stable isotope techniques and modeling approaches are needed to better understand the actual importance of HS to carbon cycling in highly humic waters.     

Biogeochemical processes at the fringe of a landfill leachate pollution plume: potential for dissolved organic carbon, Fe(II), Mn(II), NH4, and CH4 oxidation

Various redox reactions may occur at the fringe of a landfill leachate plume, involving oxidation of dissolved organic carbon (DOC), CH4, Fe(II), Mn(II), and NH4 from leachate and reduction of O2, NO3 and SO4 from pristine groundwater. Knowledge on the relevance of these processes is essential for the simulation and evaluation of natural attenuation (NA) of pollution plumes. The occurrence of such biogeochemical processes was investigated at the top fringe of a landfill leachate plume (Banisveld, the Netherlands). Hydrochemical depth profiles of the top fringe were captured via installation of a series of multi-level samplers at 18, 39 and 58 m downstream from the landfill. Ten-centimeter vertical resolution was necessary to study NA within a fringe as thin as 0.5 m. Bromide appeared an equally well-conservative tracer as chloride to calculate dilution of landfill leachate, and its ratio to chloride was high compared to other possible sources of salt in groundwater. The plume fringe rose steadily from a depth of around 5 m towards the surface with a few meters in the period 1998-2003. The plume uplift may be caused by enhanced exfiltration to a brook downstream from the landfill, due to increased precipitation over this period and an artificial lowering of the water level of the brook. This rise invoked cation exchange including proton buffering, and triggered degassing of methane. The hydrochemical depth profile was simulated in a 1D vertical reactive transport model using PHREEQC-2. Optimization using the nonlinear optimization program PEST brought forward that solid organic carbon and not clay minerals controlled retardation of cations. Cation exchange resulted in spatial separation of Fe(II), Mn(II) and NH4 fronts from the fringe, and thereby prevented possible oxidation of these secondary redox species. Degradation of DOC may happen in the fringe zone. Re-dissolution of methane escaped from the plume and subsequent oxidation is an explanation for absence of previously present nitrate and anaerobic conditions in pristine groundwater above the plume. Stable carbon isotope (delta13C) values of methane confirm anaerobic methane oxidation immediately below the fringe zone, presumably coupled to reduction of sulfate, desorbed from iron oxide. Methane must be the principle reductant consuming soluble electron-acceptors in pristine groundwater, thereby limiting NA for other solutes including organic micro-pollutants at the fringe of this landfill leachate plume.     

Effects of bacterial activities on the release of heavy metals from contaminated dredged sediments

The potential impact of indigenous bacterial processes on the release of heavy metals from dredged sediment deposits was investigated. Batch re-suspension experiments were conducted in order to investigate the release of Zn, Cd, Cu and Pb from a polluted anoxic sediment submitted to oxidative perturbations. The concentrations of heavy metals, sulphate and dissolved organic carbon (DOC) were periodically recorded, and cell counts were performed to follow the evolution of several bacterial species. The specific effects of microbial processes were quantified by performing re-suspension assays on sterilised samples. Moreover, the effect of an initial acidification of the system was studied. The results showed that metal release was mainly due to oxidation of sulphide minerals contained in the sediment. Sulphur-oxidising bacteria such as Acidithiobacillus thiooxidans were identified to play a major role in the process, by enhancing the oxidation kinetic. However, the acid production resulting from these reactions was almost totally buffered by the dissolution of the calcite present in the sediment. Copper was released to a lesser extent, and a strong association with organic matter was observed. Lead was not observed in solution, because of its low solubility at neutral conditions and of its re-adsorption on the solid phase. The initial acidification of the system resulted in an faster growth of the acidophilic A. thiooxidans. A subsequent pH drop originating from microbial processes was then observed during the first stages of the experiment. As a consequence, drastic increases in metal (Zn, Cd) release were observed.     

Kinetics of peat soil dissolved organic carbon release to surface water. Part 2. A chemodynamic process model

Temporary water reservoirs built upon peat soil may exhibit water quality impairment from elevated dissolved organic carbon (DOC). Microbiological decay of the organic carbon in the bed with subsequent release produces "tea" colored water which may require treatment prior to use. This paper contains a process-based mathematical model that quantifies the DOC release from the bed and its build-up in the water column. The model elements are based on microbial DOC production rates and bed sediment transport kinetics describing its' release from the organic soil systems. It relies on laboratory data obtained from an experimental study, Part 1, designed to simulate the DOC chemodynamics of aquatic reservoirs built upon peat soils. A two-step DOC release process was structured based on the experimental findings. The model mechanism assumes a quick release fraction that characterizes the upper soil surface layers as a "tea bag" type release process. This is followed by a fraction that is continuously produced and then released at a constant rate overtime by on-going microbial processes within the upper soil layers. The depth of the active layer, selected as h* = 0.3 cm, is the single adjustable parameter in the model. Concentration predictions of the are consistent with the laboratory simulations and field observations. Measured vs. model-calculated DOC concentrations for both in the microcosm bed and water column are used to test critical features of the proposed model. As conceived and structured it appears to be a realistic first step in quantifying the DOC release consequences for the water column of a reservoir sited upon a peat-soil bed. The development ends with an application to a hypothetical reservoir in order to illustrate model strengths and uncertainties.     

Flow and transport in fractured tuff at Yucca Mountain: numerical experiments on fast preferential flow mechanisms

Recent discovery of bomb-related ³⁶Cl at depth in fractured tuff in the unsaturated zone at the Yucca Mountain candidate high-level waste (HLW) repository site has called into question the usual modeling assumptions based on the equivalent continuum model (ECM). A dual continuum model (DCM) for simulating transient flow and transport at Yucca Mountain is developed. In order to ensure properly converged flow solutions, which are used in the transport simulation, a new flow solution convergence criteria is derived. An extensive series of simulation studies is presented which indicates that rapid movement of solute through the fractures will not occur unless there are intense episodic infiltration events. Movement of solute in the environs of the repository is enhanced if the properties of the tuff layer at the repository horizon are modified from current best-estimate values. Due to a large advective–dispersive coupling between the matrix and fractures, the matrix acts as a major buffer which inhibits rapid transport along the fractures. Consequently, fast movement of solutes through the fractures to the repository depth can only be explained if the matrix–fracture coupling term is significantly reduced from a value that would be calculated on the basis of data currently available.     

Multicomponent simulation of wastewater-derived nitrogen and carbon in shallow unconfined aquifers. I. Model formulation and performance

One of the most common methods to dispose of domestic wastewater involves the release of septic effluent from drains located in the unsaturated zone. Nitrogen from such systems is currently of concern because of nitrate contamination of drinking water supplies and eutrophication of coastal waters. The objectives of this study are to develop and assess the performance of a mechanistic flow and reactive transport model which couples the most relevant physical, geochemical and biochemical processes involved in wastewater plume evolution in sandy aquifers. The numerical model solves for variably saturated groundwater flow and reactive transport of multiple carbon- and nitrogen-containing species in a three-dimensional porous medium. The reactive transport equations are solved using the Strang splitting method which is shown to be accurate for Monod and first- and second-order kinetic reactions, and two to four times more efficient than sequential iterative splitting. The reaction system is formulated as a fully kinetic chemistry problem, which allows for the use of several special-purpose ordinary differential equation (ODE) solvers. For reaction systems containing both fast and slow kinetic reactions, such as the combined nitrogen-carbon system, it is found that a specialized stiff explicit solver fails to obtain a solution. An implicit solver is more robust and its computational performance is improved by scaling of the fastest reaction rates. The model is used to simulate wastewater migration in a 1-m-long unsaturated column and the results show significant oxidation of dissolved organic carbon (DOC), the generation of nitrate by nitrification, and a slight decrease in pH.     

Impact of electrokinetic remediation on microbial communities within PCP contaminated soil

Electrokinetic techniques have been used to stimulate the removal of organic pollutants within soil, by directing contaminant migration to where remediation may be more easily achieved. The effect of this and other physical remediation techniques on the health of soil microbial communities has been poorly studied and indeed, largely ignored. This study reports the impact on soil microbial communities during the application of an electric field within ex situ laboratory soil microcosms contaminated with pentachlorophenol (PCP; 100mg kg(-1) oven dry soil). Electrokinetics reduced counts of culturable bacteria and fungi, soil microbial respiration and carbon substrate utilisation, especially close to the acidic anode where PCP accumulated (36d), perhaps exacerbated by the greater toxicity of PCP at lower soil pH. There is little doubt that a better awareness of the interactions between soil electrokinetic processes and microbial communities is key to improving the efficacy and sustainability of this remediation strategy.     

Geochemical evaluation of different groundwater-host rock systems for radioactive waste disposal

The geochemical suitability of a deep bedrock repository for radioactive waste disposal is determined by the composition of geomatrix and groundwater. Both influence radionuclide solubility, chemical buffer capacity and radionuclide retention. They also determine the chemical compatibility of waste forms, containers and backfill materials. Evaluation of different groundwater-host rock systems is performed by modeling the geochemical environments and the resulting radionuclide concentrations. In order to demonstrate the evaluation method, model calculations are applied to data sets available for various geological formations such as granite, clay and rocksalt. The saturation state of the groundwater-geomatrix system is found to be fundamental for the evaluation process. Hence, calculations are performed to determine if groundwater is in equilibrium with mineral phases of the geological formation. In addition, corrosion of waste forms in different groundwater is examined by means of reaction path modeling. The corrosion reactions change the solution compositions and pH, resulting in significant changes of radionuclide solubilities. The results demonstrate that geochemical modeling of saturation state and compatibility of the host formation environment with the radioactive waste proves to be a feasible tool for evaluation of various sites considered as deep underground repositories.     

Use of O2 consumption and CO2 production in kinetic cells to delineate pyrite oxidation-carbonate buffering and microbial respiration in unsaturated media

Identifying zones of sulphide oxidation and carbonate buffering is important in the development of a management plan for mine waste-rock piles. In this study, we used a kinetic cell technique to measure rates of O2 consumption and CO2 production in low sulphide (<0.12 wt.% S), low inorganic carbon (<0.20 wt.% C(inorganic)), gneissic waste rock and associated organic-rich lake sediment (0.7 wt.% C(organic)), and forest soil (1.4 wt.% C(organic)) collected from the Key Lake uranium mine in Saskatchewan, Canada. Solid chemistry, stable carbon isotope, pore water sulphate concentration data, and stoichiometric considerations indicated that O2 consumption and CO2 production were constrained by microbial respiration in the lake sediment and forest soil and by pyrite oxidation-carbonate buffering in the gneissic waste rock. Mean ratios of molar CO2 production to O2 consumption rates were 0.5 for lake sediment, 0.7 for forest soil, and 0.2 for gneissic waste rock. The different O2/CO2 ratios suggested that O2-CO2 monitoring may provide a practical tool for identifying the zones of microbial respiration and pyrite oxidation-carbonate buffering in mine waste-rock piles. Rates of O2 consumption and CO2 production were about one order of magnitude greater in lake sediment than in gneissic waste rock, indicating that microbial respiration would exert a control on the distribution of O2 and CO2 gas in waste-rock piles constructed upon the dewatered lake sediments.     

Geochemical evaluation of different groundwater–host rock systems for radioactive waste disposal

The geochemical suitability of a deep bedrock repository for radioactive waste disposal is determined by the composition of geomatrix and groundwater. Both influence radionuclide solubility, chemical buffer capacity and radionuclide retention. They also determine the chemical compatibility of waste forms, containers and backfill materials. Evaluation of different groundwater–host rock systems is performed by modeling the geochemical environments and the resulting radionuclide concentrations. In order to demonstrate the evaluation method, model calculations are applied to data sets available for various geological formations such as granite, clay and rocksalt.The saturation state of the groundwater–geomatrix system is found to be fundamental for the evaluation process. Hence, calculations are performed to determine if groundwater is in equilibrium with mineral phases of the geological formation. In addition, corrosion of waste forms in different groundwater is examined by means of reaction path modeling. The corrosion reactions change the solution compositions and pH, resulting in significant changes of radionuclide solubilities. The results demonstrate that geochemical modeling of saturation state and compatibility of the host formation environment with the radioactive waste proves to be a feasible tool for evaluation of various sites considered as deep underground repositories.     

Attenuation reactions in a multiple contaminated aquifer in Bitterfeld (Germany)

Large-scale contaminated sites with multiple contaminants in the groundwater present a challenge to risk assessment and remediation. Attenuation reactions take place in the subsurface and act to contain contaminants, but must be thoroughly investigated on a site-specific basis. Field data from monitoring wells at a contaminated industrial site in Bitterfeld, Germany, are presented and analyzed for evidence of the prevalent biodegradation reactions. The groundwater in the Tertiary aquifer is contaminated with large quantities of chlorinated aliphatic compounds, in addition to chlorobenzenes and BTEX. In this strictly anaerobic environment, geochemical indications for several microbial processes were found, including methanogenesis, sulfate and iron reduction as well as reductive dechlorination of the chlorinated hydrocarbons. Direct evidence for the latter degradation reaction was observed along the flowpath due to the appearance of intermediates and an increase in the degree of dechlorination.     

The influence of substrate and electron acceptor availability on bioactive zone dynamics in porous media

Two approaches were used to investigate the influence of dissolved oxygen (DO) and substrate availability on the formation and dynamics of "bioactive zones" in a water-saturated porous medium. A bioactive zone is defined as a region where a microbial community is sufficiently active to metabolize bioavailable substrates. In the first approach, microbial activity was characterized by monitoring the spatial and temporal variability of DO and aqueous substrate (salicylate and naphthalene) concentrations during miscible-displacement experiments. In the second approach, microbial activity was monitored using multiple fiber optics emplaced in the porous medium to detect luminescence produced by Pseudomonas putida RB1353, a bioluminescent reporter organism that produces light when salicylate (an intermediate of naphthalene degradation) is present. The results of both approaches show that the location and size of the bioactive zones were influenced by in situ DO and substrate availability. When DO was not a limiting factor (i.e., lower substrate input concentrations), the bioactive zone encompassed the entire column, with the majority of the microbial activity occurring between the inlet and midpoint. However, as the availability of DO became limiting for the higher substrate input experiments, the size of the bioactive zone shrank and was ultimately limited to the proximity of the column inlet.     

Engineered in situ bioremediation of a petroleum hydrocarbon-contaminated aquifer: assessment of mineralization based on alkalinity, inorganic carbon and stable carbon isotope balances

A concept is proposed to assess in situ petroleum hydrocarbon mineralization by combining data on oxidant consumption, production of reduced species, CH₄, alkalinity and dissolved inorganic carbon (DIC) with measurements of stable isotope ratios. The concept was applied to a diesel fuel contaminated aquifer in Menziken, Switzerland, which was treated by engineered in situ bioremediation. In the contaminated aquifer, added oxidants (O₂ and NO₃⁻) were consumed, elevated concentrations of Fe(II), Mn(II), CH₄, alkalinity and DIC were detected and the DIC was generally depleted in ¹³C compared to the background. The DIC production was larger than expected based on the consumption of dissolved oxidants and the production of reduced species. Stable carbon isotope balances revealed that the DIC production in the aquifer originated mainly from microbial petroleum hydrocarbon mineralization, and that geochemical reactions such as carbonate dissolution produced little DIC. This suggests that petroleum hydrocarbon mineralization can be underestimated if it is determined based on concentrations of dissolved oxidants and reduced species.