Leaching behaviour of elements and evaluation of pre-treatment methods for municipal solid waste incinerator residues in column leaching tests.

Two new pre-treatment methods (water-washing/carbonation and carbonation/phosphate stabilization) of municipal solid waste (MSW) incinerator residues were evaluated by column leaching tests under aerobic conditions and anaerobic conditions (which were changed to aerobic conditions after 10 months). A mixture of bottom ash and fly ash (5:1 ratio) was pre-treated using each method. Shredded incombustible residues (SIR) were added to each ash preparation in proportions similar to the ratios present in landfills. For comparison, landfill wastes typical of Japan, namely, a mixture of bottom ash, chelating-pre-treated fly ash, and SIR, were also examined. Leachate samples were collected periodically and analysed over a 15-month period. When compared with chelating pretreatment, both water-washing/carbonation and carbonation/ phosphate stabilization reduced the leaching of Pb, Al, and Cu by about one to two orders of magnitude. Moreover, the initial concentrations of Ca and Pb in leachates from column of water-washing/carbonation were 56-57% and 84-96% less than those from the column of carbonation/phosphate stabilization. Therefore, water-washing/carbonation was considered to be a promising approach to obtain early waste stabilization and to reduce the release of heavy metals to near-negligible levels. The leaching behaviour of elements was also discussed.     

Temporary stabilization of air pollution control residues using carbonation

Carbonation presents a good prospect for stabilizing alkaline waste materials. The risk of metal leaching from carbonated waste was investigated in the present study; in particular, the effect of the carbonation process and leachate pH on the leaching toxicity of the alkaline air pollution control (APC) residues from municipal solid waste incinerator was evaluated. The pH varying test was conducted to characterize the leaching characteristics of the raw and carbonated residue over a broad range of pH. Partial least square modeling and thermodynamic modeling using Visual MINTEQ were applied to highlight the significant process parameters that controlled metal leaching from the carbonated residue. By lowering the pH to 8-11, the carbonation process reduced markedly the leaching toxicity of the alkaline APC residue; however, the treated APC residue showed similar potential risk of heavy metal release as the raw ash when subjected to an acid shock. The carbonated waste could, thereby, not be disposed of safely. Nonetheless, carbonation could be applied as a temporary stabilization process for heavy metals in APC residues in order to reduce the leaching risk during its transportation and storage before final disposal.     

Co-gasification of municipal solid waste and material recovery in a large-scale gasification and melting system

This study evaluates the effects of co-gasification of municipal solid waste with and without the municipal solid waste bottom ash using two large-scale commercial operation plants. From the viewpoint of operation data, there is no significant difference between municipal solid waste treatment with and without the bottom ash. The carbon conversion ratios are as high as 91.7% and 95.3%, respectively and this leads to significantly low PCDD/DFs yields via complete syngas combustion. The gross power generation efficiencies are 18.9% with the bottom ash and 23.0% without municipal solid waste bottom ash, respectively. The effects of the equivalence ratio are also evaluated. With the equivalence ratio increasing, carbon monoxide concentration is decreased, and carbon dioxide and the syngas temperature (top gas temperature) are increased. The carbon conversion ratio is also increased. These tendencies are seen in both modes.Co-gasification using the gasification and melting system (Direct Melting System) has a possibility to recover materials effectively. More than 90% of chlorine is distributed in fly ash. Low-boiling-point heavy metals, such as lead and zinc, are distributed in fly ash at rates of 95.2% and 92.0%, respectively. Most of high-boiling-point heavy metals, such as iron and copper, are distributed in metal. It is also clarified that slag is stable and contains few harmful heavy metals such as lead. Compared with the conventional waste management framework, 85% of the final landfill amount reduction is achieved by co-gasification of municipal solid waste with bottom ash and incombustible residues. These results indicate that the combined production of slag with co-gasification of municipal solid waste with the bottom ash constitutes an ideal approach to environmental conservation and resource recycling.     

利用生活垃圾填埋场上建设飞灰固化物填埋场适宜性探讨

针对利用原有生活垃圾填埋场改扩建飞灰固化物填埋场,从勘查设计和建设角度,通过与常规生活垃圾填埋的安全和环保各相关因素对比,分析扩建前后填埋场稳定性、防渗及导排系统等勘察设计要点,研讨扩建工程新老填埋堆体基础层、防渗及导排系统等安全环保关键技术及扩建的适宜性,为扩建的可行性研究提出较为系统的技术论证思路.     

Strength, leachability and microstructure characterisation of Na2SiO3-activated ground granulated blast-furnace slag solidified MSWI fly ash.

The chemical composition and the leachability of heavy metals in municipal solid waste incinerator (MSWI) fly ash were measured and analysed. For the leachability of unstabilized MSWI fly ash it was found that the concentrations of Pb and Cr exceeded the leaching toxicity standard. Cementitious solidification of the MSWI fly ash by Na2SiO3-activated ground granulated blast-furnace slag (NS) was investigated. Results show that all solidified MSWI fly ash can meet the landfill standards after 28 days of curing. The heavy metals were immobilized within the hydration products such as C-S-H gel and ettringite through physical encapsulation, substitution, precipitation or adsorption mechanisms.     

Physical containment of municipal solid waste incineration bottom ash by accelerated carbonation

Accelerated carbonation of municipal solid waste incineration residues is effective for immobilizing heavy metals. In this study, the contribution of the physical containment by carbonation to immobilization of some heavy metals was examined by some leaching tests and SEM–EDS analysis of untreated, carbonated, and milled bottom ash after carbonation that was crushed with a mortar to a mean particle size of approximately 1 μm. The surface of carbonated bottom ash particles on SEM images seemed mostly coated, while there were uneven micro-spaces on the surface of the untreated bottom ash. Results of Japan Leaching Test No. 18 (JLT18) for soil pollution showed that milling carbonated bottom ash increased the pH and EC. The leaching concentration of each element tended to be high for untreated samples, and was decreased by carbonation. However, after the milling of carbonated samples, the leaching concentration became high again. The immobilization effect of each element was weakened by milling. The ratio of physical containment effect to immobilization effects by accelerated carbonation was calculated using the results of JLT18. The ratio for each element was as follows: Pb: 13.9–69.0 %, Cu: 12.0–49.1 %, Cr: 24.1–99.7 %, Zn: 20.0–33.3 %, and Ca: 28.9–63.4 %.     

Trace element partitioning in ashes from boilers firing pure wood or mixtures of solid waste with respect to fuel composition,chlorine content and temperature

Trace element partitioning in solid waste (household waste, industrial waste, waste wood chips and waste mixtures) incineration residues was investigated. Samples of fly ash and bottom ash were collected from six incineration facilities across Sweden including two grate fired and four fluidized bed incinerators, to have a variation in the input fuel composition (from pure biofuel to mixture of waste) and different temperature boiler conditions. As trace element concentrations in the input waste at the same facilities have already been analyzed, the present study focuses on the concentration of trace elements in the waste fuel, their distribution in the incineration residues with respect to chlorine content of waste and combustion temperature.Results indicate that Zn, Cu and Pb are dominating trace elements in the waste fuel. Highly volatile elements mercury and cadmium are mainly found in fly ash in all cases; 2/3 of lead also end up in fly ash while Zn, As and Sb show a large variation in distribution with most of them residing in the fly ash. Lithophilic elements such as copper and chromium are mainly found in bottom ash from grate fired facilities while partition mostly into fly ash from fluidized bed incinerators, especially for plants fuelled by waste wood or ordinary wood chips. There is no specific correlation between input concentration of an element in the waste fuel and fraction partitioned to fly ash. Temperature and chlorine content have significant effects on partitioning characteristics by increasing the formation and vaporization of highly volatile metal chlorides. Zinc and cadmium concentrations in fly ash increase with the incineration temperature.     

Leaching behavior of polychlorinated dibenzo-p-dioxins and furans from the fly ash and bottom ash of a municipal solid waste incinerator

The leaching behavior of dioxins from landfill containing bottom ash and fly ash from municipal solid waste incineration has been investigated by leaching tests with pure water, non-ionic surfactant solutions, ethanol solutions, or acetic acid solutions as elution solvents for a large-scale cylindrical column packed with ash. Larger amounts of dioxins were eluted from both bottom ash and fly ash with ethanol solution and acetic acid solution than with pure water. Large quantities of dioxins were leached from fly ash but not bottom ash by non-ionic surfactant solutions. The patterns of distribution of the dioxin congeners in the leachates were very similar to those in the bottom ash or fly ash from which they were derived.     

Demobilisation of critical contaminants in four typical waste-to-energy ashes by carbonation

Two bottom ashes, one air pollution control (APC) residue and one fly ash from three different Swedish municipal solid waste incineration (MSWI) plants were characterised regarding the leaching of environmentally relevant components. Characterisation was performed using a diffusion tank leaching test. The impact of carbonation on the release of eight critical components, i.e., Cl(-), Cr, Cu, Mo, Pb, Sb, Se, SO(4)(2-) and Zn, was assessed at a lab-scale and showed carbonation to have a more pronounced demobilising effect on critical components in bottom ashes than in APC residue and fly ash. From grate type incinerator bottom ash, the release of Cr decreased by 97%, by 63% for Cu and by 45% for Sb. In the investigated APC residue, the releases of Cr, Se and Pb were defined as critical, although they either remained unaffected or increased after carbonation. Cl(-) and SO(4)(2-) remained mobile after carbonation in all investigated residues.     

Environmental assessment of incinerator residue utilisation

Incineration ashes may be treated either as a waste to be dumped in landfill, or as a resource that is suitable for re-use. In order to choose the best management scenario, knowledge is needed on the potential environmental impact that may be expected, including not only local, but also regional and global impact. In this study, A life cycle assessment (LCA) based approach was outlined for environmental assessment of incinerator residue utilisation, in which leaching of trace elements as well as other emissions to air and water and the use of resources were regarded as constituting the potential environmental impact from the system studied. Case studies were performed for two selected ash types, bottom ash from municipal solid waste incineration (MSWI) and wood fly ash. The MSWI bottom ash was assumed to be suitable for road construction or as drainage material in landfill, whereas the wood fly ash was assumed to be suitable for road construction or as a nutrient resource to be recycled on forest land after biofuel harvesting. Different types of potential environmental impact predominated in the activities of the system and the use of natural resources and the trace element leaching were identified as being relatively important for the scenarios compared. The scenarios differed in use of resources and energy, whereas there is a potential for trace element leaching regardless of how the material is managed. Utilising MSWI bottom ash in road construction and recycling of wood ash on forest land saved more natural resources and energy than when these materials were managed according to the other scenarios investigated, including dumping in landfill.     

Artificial carbonation for controlling the mobility of critical elements in bottom ash

In municipal solid waste incineration (MSWI), bottom ash, generated at a stoker grate type incinerator, the critical elements were identified in terms of EU regulation. The stabilizing effect of moderate carbonation (pH 8.28 ± 0.03) on critical contaminants was studied through availability and diffusion leaching protocols. Data from the performed tests were evaluated with the goal of reusing MSWI bottom ash as secondary construction material. To investigate the mobilizing effect of CO₂, suspended MSWI bottom ash was severely carbonated (pH 6.40 ± 0.07). The effect of CO₂ and its interaction with other leaching factors, such as liquid/solid (L/S) ratio, leaching time, pH, ultrasound treatment, and leaching temperature, were examined using a reduced 2^6-1 experimental design. Contaminants identified as critical were Cr, Cu, Mo, Sb, Cl⁻, and SO₄ ²⁻. Although moderate carbonation decreased the release of Cr, Cu, Mo, and Sb from compacted bottom ash, the main disadvantage remains its inability to demobilize Cl⁻ and SO₄ ²⁻. The hypothesized mobilizing effect of severe carbonation was proven. The treatment enhanced the separation of critical components (α = 0.05) (except for Cl⁻), i.e., about fivefold for Sb and about twofold for Cr, Cu, and S. Nevertheless, the prospect is good that severe carbonation could constitute the deciding key parameter to facilitate the technical feasibility of a future washing process for MSWI bottom ash.     

Thermal and hydrometallurgical recovery methods of heavy metals from municipal solid waste fly ash

Heavy metals in fly ash from municipal solid waste incinerators are present in high concentrations. Therefore fly ash must be treated as a hazardous material. On the other hand, it may be a potential source of heavy metals. Zinc, lead, cadmium, and copper can be relatively easily removed during the thermal treatment of fly ash, e.g. in the form of chlorides. In return, wet extraction methods could provide promising results for these elements including chromium and nickel. The aim of this study was to investigate and compare thermal and hydrometallurgical treatment of municipal solid waste fly ash. Thermal treatment of fly ash was performed in a rotary reactor at temperatures between 950 and 1050 °C and in a muffle oven at temperatures from 500 to 1200 °C. The removal more than 90% was reached by easy volatile heavy metals such as cadmium and lead and also by copper, however at higher temperature in the muffle oven. The alkaline (sodium hydroxide) and acid (sulphuric acid) leaching of the fly ash was carried out while the influence of temperature, time, concentration, and liquid/solid ratio were investigated. The combination of alkaline-acidic leaching enhanced the removal of, namely, zinc, chromium and nickel.     

Cement solidification of simulated off-gas condensates from vitrification of low-level nuclear waste solutions

Solidification in a cementitious matrix is a viable alternative for low-level nuclear waste management; it is therefore important to understand the behavior and properties of such wasteforms. We have examined the cementitious solidification of simulated off-gas waste streams resulting from the vitrification of low-level nuclear waste. Different possible methods for scrubbing the off-gasses from a vitrifier give rise to three possible types of waste compositions: acidic (from aqueous dissolution of volatile NOx and POx carried over from the vitrifier), basic (from neutralizing the former with sodium hydroxide), and fully carbonated (arising from a direct-combustion vitrifier). Six binder compositions were tested in which ordinary Portland cement was replaced at different proportions by fly ash and/or ground granulated blast furnace slag. A high solution to binder ratio of 1l/1 kg was used to minimize the volume of the wasteform and 10% attapulgite clay was added to all mixes to ensure that the fresh mix did not segregate prior to setting. The 28-day compressive strengths decreased when a high proportion of cement was replaced with fly ash, but were increased significantly when the cement was replaced with slag. The heats of hydration at early age for the various solids compositions decreased when cement was replaced with either fly ash or slag; however, for the fly ash mix the low heat was also associated with a significant decrease in compressive strength. High curing temperature (60 degrees C) or the use of extra-fine slag did not significantly affect the compressive strength. Recommendations for choice of binder formulations and treatment of off-gas condensates are discussed.     

Occurrence of phenols in leachates from municipal solid waste landfill sites in Japan

The concentrations of 41 phenols in leachates from 38 municipal solid waste (MSW) landfill sites in Japan were measured. The main phenols detected in leachates were phenol, three cresols, 4-tert-butylphenol, 4-tertoctylphenol, 4-nonylphenol, bisphenol A, and some chlorophenols. The concentration levels of phenols were affected by the pH values of the leachates and the different types of landfill waste. The origins of phenol and p-cresol were considered to be incineration residues, and the major origin of 4-tert-butylphenol, bisphenol A, and 2,4,6-trichlorophenol was considered to be solidified fly ash. In contrast, the major origins of 4-tert-octylphenol and 4-nonylphenol were considered to be incombustibles. The discharge of leachates to the environment around MSW landfill sites without water treatment facilities can cause environmental pollution by phenols. In particular, the disposal of incineration residues including solidified fly ash and the codisposal of solidified fly ash and incombustibles might raise the possibility of environmental pollution. Moreover, the discharge of leachates at pH values of 9.8 or more could pollute the water environment with phenol. However, phenol, 4-nonylphenol, and bisphenol A can be removed to below the con centration levels that impact the environment around landfill sites by a series of conventional water treatment processes.     

Comparison of leaching characteristics of heavy metals from bottom and fly ashes in Korea and Japan

The objective of this research was to compare the leaching characteristics of heavy metals such as cadmium, chromium, copper, nickel, lead, etc., in Korean and Japanese municipal solid waste incineration (MSWI) ash. The rate of leaching of heavy metal was measured by KSLT and JTL-13, and the amount of heavy metals leached was compared with the metal content in each waste component. Finally, bio-availability testing was performed to assess the risks associated with heavy metals leached from bottom ash and fly ash. From the results, the value of neutralization ability in Japanese fly ash was four times higher than that in Korean fly ash. The reason was the difference in the content of Ca(OH)(2) in fly ash. The amount of lead leached exceeded the regulatory level in both Japanese and Korean fly ash. The rate of leaching was relatively low in ash with a pH in the range of 6-10. The bio-availability test in fly ash demonstrated that the amount of heavy metals leached was Pb>Cd>Cr, but the order was changed to Pb>Cr>Cd in the bottom ash. The leaching concentration of lead exceeded the Japanese risk level in all fly ashes from the two countries, but the leaching concentration of cadmium exceeded the regulatory level in Korean fly ash only.     

Wet extraction of heavy metals and chloride from MSWI and straw combustion fly ashes

Fly ash residues from combustion often do not meet the criteria neither for reuse as construction materials nor landfilling as non-hazardous waste, mainly because of the high concentration of heavy metals and chlorides. This work aimed to technically evaluate an innovative wet treatment process for the extraction of chloride (Cl^?), cadmium (Cd), copper (Cu), lead (Pb) and zinc (Zn) from fly ashes from a municipal solid waste incineration (MSWI) plant and from a straw combustion (SC) facility. Factors investigated were liquid/solid (L/S) ratio, full carbonation (CO₂ treatment), influence of pH and leaching time, using a two-level full factorial design. The most significant factor for all responses was low pH, followed by L/S ratio. Multiple linear regression models describing the variation in extraction data had R² values ranging from 58% to 98%. An optimization of the element extraction models was performed and a set of treatment conditions is suggested.     

The effect of accelerated carbonation on the properties of cement-solidified waste forms

Ordinary Portland cement blended with blast furnace slag and pulverised fuel ash was used to solidify two industrial wastes containing large amounts of metals. The solidified mixes were carbonated using an accelerated regime previously established and compared for strength development, leaching characteristics and phase development against their non-carbonated analogues. A significant difference in the immobilisation of metals such as Zn, Ni and As was recorded for samples in which carbonation was optimised. The work has shown that by controlling mix parameters it is possible to improve the immobilisation of specific metals. Electron microanalysis showed that this is partly due to the precipitation of calcite in the solidified waste pore structure. Carbonation was also found to accelerate C₃S hydration in all carbonated samples and to modify the morphology of residual cement grains through the formation of a calcite coating over de-calcified hydration rims. Some metals appear to be incorporated in both of these zones.     

Stabilization/solidification of MSW incineration residues from facilities with different air pollution control systems. Durability of matrices versus carbonation

This paper discusses the stabilisation/solidification process with Portland cement applied to municipal solid waste incineration residues. Two types of residues were considered: fly ash (FA) produced in an electrostatic precipitator, and air pollution control (APC) residues from a semi-dry scrubber process. Cement pastes with different percentages of FA and APC residues were characterised according to their physical properties, the effect of the hydration products and their leaching behaviour. Portland pastes prepared with APC residues showed a rapid setting velocity in comparison with setting time for those pastes substituted with FA residues. Portland cement hydration was retarded in FA pastes. Leaching test results showed that heavy metals (such as Zn, Pb and Cd) and sulphates are immobilised within the paste, whereas chlorides are only partially retained. The carbonation process increases the leachability of S04(2-) and heavy metals such as Zn and Cr.     

Mechanisms contributing to the thermal analysis of waste incineration bottom ash and quantification of different carbon species

The focus of this study was to identify the main compounds affecting the weight changes of bottom ash (BA) in conventional loss on ignition (LOI) tests and to obtain a better understanding of the individual processes in heterogeneous (waste) materials such as BA. Evaluations were performed on BA samples from a refuse derived fuel incineration (RDF-I) plant and a hospital waste incineration (HW-I) plant using thermogravimetric analysis and subsequent mass spectrometry (TG–MS) analysis of the gaseous thermal decomposition products. Results of TG–MS analysis on RDF-I BA indicated that the LOI measured at 550 °C was due to moisture evaporation and dehydration of Ca(OH)₂ and hydrocalumite. Results for the HW-I BA showed that LOI at 550 °C was predominantly related to the elemental carbon (EC) content of the sample. Decomposition of CaCO₃ around 700 °C was identified in both materials. In addition, we have identified reaction mechanisms that underestimate the EC and overestimate the CaCO₃ contents of the HW-I BA during TG–MS analyses. These types of artefacts are expected to occur also when conventional LOI methods are adopted, in particular for materials that contain CaO/Ca(OH)₂ in combination with EC and/or organic carbon, such as e.g. municipal solid waste incineration (MSWI) bottom and fly ashes. We suggest that the same mechanisms that we have found (i.e. in situ carbonation) can also occur during combustion of the waste in the incinerator (between 450 and 650 °C) demonstrating that the presence of carbonate in bottom ash is not necessarily indicative for weathering. These results may also give direction to further optimization of waste incineration technologies with regard to stimulating in situ carbonation during incineration and subsequent potential improvement of the leaching behavior of bottom ash.     

Sequestration of metals in carbonated municipal solid waste incineration (MSWI) fly ash

Waste management is in need of a reliable and economical treatment method for metals in fly ashes from municipal solid waste incineration (MSWI). However, no state-of-the-art technique has gained wide acceptance yet. This paper is a synthesis of five elsewhere published investigations covering a project which aimed to assess the possibilities and limitations of adding carbon dioxide (CO2) to fly ash as a stabilization method. Carbonation factors that were studied are the partial pressure of carbon dioxide (CO2), the addition of water, the temperature, and the reaction time. Laboratory experiments were performed applying methods such as factorial experimental design, thermal analysis, scanning electron microscopy (SEM), X-ray diffraction (XRD), and leaching assays including pHstat titration and sequential extraction. Leaching data were verified and complemented using chemical equilibrium calculations. Data evaluation was performed by means of multivariate statistics such as multiple linear regression, principal component analysis (PCA), and partial least squares (PLS) modeling. It was found that carbonation is a good prospect for a stabilization technique especially with respect to the major pollutants lead (Pb) and zinc (Zn). Their mobility decreased with increasing factor levels. Dominating factors were the partial pressure of CO2 and the reaction time, while temperature and the addition of water were of minor influence. However, the treatment caused a mobilization of cadmium (Cd), requiring further research on possible countermeasures such as metal demobilization through enhanced silicate formation.