Simultaneous heavy metal removal mechanism by dead macrophytes

The use of dead, dried aquatic plants, for water removal of metals derived from industrial activities as a simple biosorbent material has been increasing in the last years. The mechanism of simultaneous metal removal (Cd2+, Ni2+, Cu2+, Zn2+ and Pb2+) by 3 macrophytes biomass (Spirodela intermedia, Lemna minor and Pistia stratiotes) was investigated. L. minor biomass presented the highest mean removal percentage and P. stratiotes the lowest for all metals tested. Pb2+ and Cd2+ were more efficiently removed by the three of them. The simultaneous metal sorption data were analysed according to Langmuir and Freundlich isotherms. Data fitted the Langmuir model only for Ni and Cd, but Freundlich isotherm for all metals tested, as it was expected. The K(F) values showed that Pb was the metal more efficiently removed from water solution. The adsorption process for the three species studied followed first order kinetics. The mechanism involved in biosorption resulted ion exchange between monovalent metals as counter ions present in the macrophytes biomass and heavy metal ions and protons taken up from water. No significant differences were observed in the metal exchange amounts while using multi-metal or individual metal solutions.     

The effect of coagulation on the toxicity and mutagenicity of reclaimed municipal effluents

The objectives of this work were the assessment of the effectiveness of coagulation on the reclamation of secondary effluents and the evaluation of the quality of reclaimed waters by the examination of their ecotoxic and mutagenic properties. Aluminum coagulants resulted in higher removal of organic content, than iron coagulant, reaching up to 40%; the removal of heavy metals, such as zinc and copper was enhanced by the addition of a low strength anionic flocculant. The toxicity of pre-concentrated samples to the bacteria Vibrio fischerii was related to the heavy metal content, especially zinc and copper, indicating the significance of the metals bioavailability and their potential interactive effects. The secondary effluents exhibited mutagenic effects on strain TA 98; these effects were increased during coagulation with ferric chloride (both in absence and presence of flocculant). However, the addition of aluminum coagulants resulted in a decrease of mutagenic potential of secondary effluents, due to the extended removal of organic matter.     

Assessment of human health risks and pollution index for heavy metals in farmlands irrigated by effluents of stabilization ponds

Areas contaminated with heavy metals can pose major risks to human health and ecological environments. The aims of this study are to assess human health risk and pollution index for heavy metals in agricultural soils irrigated by effluents of stabilization ponds in Birjand, Iran. The results revealed that the levels of Cr, Mn, Zn, Fe, Cu, Cd, and Pb were in range of 70.3–149.65, 355–570, 31.15–98.45, 23,925–29,140, 22.75–25.95, 0.17–6.51, and 8.5–23.5 mg/kg in topsoils, respectively. Total hazard index values from heavy metals through three exposure routes for adults and children were 9.13E−01 and 1.10, respectively, indicating that there was non-carcinogenic risk for children. The total risk of carcinogenic metals (Cr, Cd, and Pb) through the three exposure routes for adults and children was 1.06E−04 and 9.76E−04, respectively, which indicates that the metals in the soil will not induce carcinogenic risks to these age groups. Pollution levels of heavy metals in soil samples including enrichment factor (EF), contamination factor (CF), pollution load index (PLI), and geo-accumulation index (Igeo) showed heavy metal contamination of agricultural soils. The results of the present study provide basic information about heavy metal contamination control and human health risk assessment management in the study area.     

Heavy metals in plants and phytoremediation

GOAL, SCOPE AND BACKGROUND: In some cases, soil, water and food are heavily polluted by heavy metals in China. To use plants to remediate heavy metal pollution would be an effective technique in pollution control. The accumulation of heavy metals in plants and the role of plants in removing pollutants should be understood in order to implement phytoremediation, which makes use of plants to extract, transfer and stabilize heavy metals from soil and water. METHODS: The information has been compiled from Chinese publications stemming mostly from the last decade, to show the research results on heavy metals in plants and the role of plants in controlling heavy metal pollution, and to provide a general outlook of phytoremediation in China. Related references from scientific journals and university journals are searched and summarized in sections concerning the accumulation of heavy metals in plants, plants for heavy metal purification and phytoremediation techniques. RESULTS AND DISCUSSION: Plants can take up heavy metals by their roots, or even via their stems and leaves, and accumulate them in their organs. Plants take up elements selectively. Accumulation and distribution of heavy metals in the plant depends on the plant species, element species, chemical and bioavailiability, redox, pH, cation exchange capacity, dissolved oxygen, temperature and secretion of roots. Plants are employed in the decontamination of heavy metals from polluted water and have demonstrated high performances in treating mineral tailing water and industrial effluents. The purification capacity of heavy metals by plants are affected by several factors, such as the concentration of the heavy metals, species of elements, plant species, exposure duration, temperature and pH. CONCLUSIONS: Phytoremediation, which makes use of vegetation to remove, detoxify, or stabilize persistent pollutants, is a green and environmentally-friendly tool for cleaning polluted soil and water. The advantage of high biomass productive and easy disposal makes plants most useful to remediate heavy metals on site. RECOMMENDATIONS AND OUTLOOK: Based on knowledge of the heavy metal accumulation in plants, it is possible to select those species of crops and pasturage herbs, which accumulate fewer heavy metals, for food cultivation and fodder for animals; and to select those hyperaccumulation species for extracting heavy metals from soil and water. Studies on the mechanisms and application of hyperaccumulation are necessary in China for developing phytoremediation.     

Selective removal of heavy metals from metal-bearing wastewater in a cascade line reactor

Goal, Scope and Background This paper is a part of the research work on ‘Integrated treatment of industrial wastes towards prevention of regional water resources contamination — INTREAT’ the project. It addresses the environmental pollution problems associated with solid and liquid waste/effluents produced by sulfide ore mining and metallurgical activities in the Copper Mining and Smelting Complex Bor (RTB-BOR), Serbia. However, since the minimum solubility for the different metals usually found in the polluted water occurs at different pH values and the hydroxide precipitates are amphoteric in nature, selective removal of mixed metals could be achieved as the multiple stage precipitation. For this reason, acid mine water had to be treated in multiple stages in a continuous precipitation system-cascade line reactor. Materials and Methods All experiments were performed using synthetic metal-bearing effluent with chemical a composition similar to the effluent from open pit, Copper Mining and Smelting Complex Bor (RTB-BOR). That effluent is characterized by low pH (1.78) due to the content of sulfuric acid and heavy metals, such as Cu, Fe, Ni, Mn, Zn with concentrations of 76.680, 26.130, 0.113, 11.490, 1.020 mg/dm³, respectively. The cascade line reactor is equipped with the following components: for feeding of effluents, for injection of the precipitation agent, for pH measurements and control, and for removal of the process gases. The precipitation agent was 1M NaOH. In each of the three reactors, a changing of pH and temperature was observed. In order to verify efficiency of heavy metals removal, chemical analyses of samples taken at different pH was done using AES-ICP. Results Consumption of NaOH in reactors was 370 cm³, 40 cm³ and 80 cm³, respectively. Total time of the experiment was 4 h including feeding of the first reactor. The time necessary to achieve the defined pH value was 25 min for the first reactor and 13 min for both second and third reactors. Taking into account the complete process in the cascade line reactor, the difference between maximum and minimum temperature was as low as 6°C. The quantity of solid residue in reactors respectively was 0.62 g, 2.05 g and 3.91 g. In the case of copper, minimum achieved concentration was 0.62 mg/dm³ at pH = 10.4. At pH = 4.50 content of iron has rapidly decreased to < 0.1 mg/dm³ and maintained constant at all higher pH values. That means that precipitation has already ended at pH=4.5 and maximum efficiency of iron removal was 99.53%. The concentration of manganese was minimum at pH value of 11.0. Minimum obtained concentration of Zn was 2.18 mg/dm³ at a pH value of 11. If pH value is higher than 11, Zn can be re-dissolved. The maximum efficiency of Ni removal reached 76.30% at a pH value of 10.4. Discussion Obtained results show that efficiency of copper, iron and manganese removal is very satisfactory (higher than 90%). The obtained efficiency of Zn and Ni removal is lower (72.30% and 76.31%, respectively). The treated effluent met discharge water standard according to The Council Directive 76/464/EEC on pollution caused by certain dangerous substances into the aquatic environment of the Community. Maximum changing of temperature during the whole process was 6°C. Conclusion This technology, which was based on inducing chemical precipitation of heavy metals is viable for selective removal of heavy metals from metal-bearing effluents in three reactor systems in a cascade line. Recommendations and Perspectives The worldwide increasing concern for the environment and guidelines regarding effluent discharge make their treatment necessary for safe discharge in water receivers. In the case where the effluents contain valuable metals, there is also an additional economic interest to recover these metals and to recycle them as secondary raw materials in different production routes. ESS-Submission Editor: PhD Hailong Wang, hailong.wang@ensisjv.com     

农林生物质在含铬废水处理中的应用

农林生物质作为低成本吸附剂在环境污染治理中日益受到重视。综述了农林生物质在含铬废水处理中的应用研究进展,分析了生物质处理含铬废水的机理、影响因素,指出了生物质法处理含铬废水的发展方向。     

农林生物质在含铬废水处理中的应用

农林生物质作为低成本吸附剂在环境污染治理中日益受到重视。综述了农林生物质在含铬废水处理中的应用研究进展，分析了生物质处理含铬废水的机理、影响因素，指出了生物质法处理含铬废水的发展方向。     

三峡库区垃圾渗滤液-城镇污水合并处理时的重金属含量研究

应用微波消解-电感耦合等离子体发射光谱法（ICP-OES）测定三峡库区垃圾渗滤液、渗滤液城镇污水合并处理厂进、出水以及剩余污泥中重金属元素的浓度。结果表明，合并处理后，除5个污水厂出水Ni超标（浓度为59.79～104.30 μg/L）外，其余重金属元素均低于GB 18918-2002污水排放标准；剩余污泥中的总重金属含量在15.31～27.73 g/kg之间，各元素含量均远低于污泥农用标准。因此，在目前各合并处理厂的运行条件下，控制渗滤液与城镇污水比例在1∶2 700～1∶50（V/V）范围内，渗滤液汇入生活污水进行合并处理是解决渗滤液重金属污染的有效方式。     

Biosorption of copper(II) from aqueous solutions by pre-treated biomass of marine algae Padina sp

Biosorption of heavy metals can be an effective process for the removal and recovery of heavy metal ions from aqueous solutions. The biomass of marine algae has been reported to have high uptake capacities for a number of heavy metal ions. In this paper, the adsorption properties of a pre-treated biomass of marine algae Padina sp. for copper(II) were investigated. Equilibrium isotherms and kinetics were obtained from batch adsorption experiments. The biosorption capacities were solution pH dependent and the maximum capacity obtained was 0.80 mmol/g at a solution pH of about 5. The biosorption kinetics was found to be fast, with 90% of adsorption within 15 min and equilibrium reached at 30 min. The effects of light metal ions on copper(II) uptake were studied and the presence of light metal ions did not affect copper(II) uptake significantly. Fixed-bed breakthrough curves for copper(II) removal were also obtained. This study demonstrated that the pre-treated biomass of Padina sp. could be used as an effective biosorbent for the treatment of copper(II) containing wastewater streams.     

Phytoremediation Potential of Aquatic Macrophyte, <Emphasis Type="Italic">Azolla</Emphasis>

Aquatic macrophytes play an important role in the structural and functional aspects of aquatic ecosystems by altering water movement regimes, providing shelter to fish and aquatic invertebrates, serving as a food source, and altering water quality by regulating oxygen balance, nutrient cycles, and accumulating heavy metals. The ability to hyperaccumulate heavy metals makes them interesting research candidates, especially for the treatment of industrial effluents and sewage waste water. The use of aquatic macrophytes, such as Azolla with hyper accumulating ability is known to be an environmentally friendly option to restore polluted aquatic resources. The present review highlights the phytoaccumulation potential of macrophytes with emphasis on utilization of Azolla as a promising candidate for phytoremediation. The impact of uptake of heavy metals on morphology and metabolic processes of Azolla has also been discussed for a better understanding and utilization of this symbiotic association in the field of phytoremediation.     

Metal uptake capacity of modified Saccharomyces pastorianus biomass from different types of solution

In this paper, we investigate the effect of different biomass pretreatments on metal ion uptake by various biosorbents. Heat-treated as well as caustic-treated and ground biomass of Saccharomyces pastorianus was used to remove copper, lead and cadmium from various solutions. Untreated yeast was used as the control sample. The effect of yeast modification on sorption capacity depended on the different types of heavy metal ions and whether they were in single- or multi-component solutions. The highest uptake of copper and lead from a single-metal solution was obtained from heat-treated cells. Ground biomass was the most efficient at cadmium removal. However, the sorption capacity of the modified biomass did not improve when metal ions were removed from multi-component solutions. Indeed, the results in this paper show that optimizing metal removal from single-cation solutions can lead to decreased sorption capacity in multi-component solutions. Therefore, while adjusting the procedure of biomass modification, not only the nature of the metal ion being sorbed but also the chemical composition of the metal ion solution should be taken into account.     

Removal of toxic metals from solution by leaf, stem and root phytomass of Quercus ilex L. (holly oak)

Increased consciousness for safeguarding the aqueous environment has prompted a search for alternative technologies for the removal of toxic metal ions from aqueous solutions. In this regard, a wide variety of biomass is being considered as adsorbents of heavy metals for treatment of industrial and domestic wastewaters as well as natural waters, including drinking water. In the present investigation, the potential of Quercus ilex phytomass from stem, leaf and root as an adsorbent of chromium (Cr), nickel (Ni), copper (Cu), cadmium (Cd) and lead (Pb) at ambient temperature was investigated. The metal uptake capacity of the root for different metals was found to be in the order: Ni>Cd>Pb>Cu>Cr; stem Ni>Pb>Cu>Cd>Cr; and leaf Ni>Cd>Cu>Pb>Cr. The highest amount adsorbed was Ni (root>leaf>stem). Data from this laboratory demonstrated that Ni is sequestered mostly in the roots, where concentrations can be as high as 428.4 ng/g dry wt., when 1-year-old seedlings were treated with Ni (2000 mg/l) in pot culture experiments, compared to 7.63 ng/g dry wt., control (garden and greenhouse soil) topsoil where Ni was present in trace amounts. This proves that the root biomass of Q. ilex has the capacity for complexing Ni. Cr exhibited the least adsorption values for all the three types of phytomass compared to other metals. The trend of adsorption of the phytomass was similar for Ni and Cd, i.e. root>leaf>stem. Desorption with 10 mM Na(4) EDTA was effective (55-90%) and, hence, there exists the possibility of recycling the phytomass. The biosorption results of recycled phytomass suggest that the selected adsorbents are re-usable. The advantages and potential of the Q. ilex phytomass as a biofilter of toxic trace metals, the scope and need for enhancing the efficiency of the Q. ilex phytomass as an adsorbent of metals are presented.     

常用城市污水再生处理工艺净化效果比较分析

以城市污水回用为目的,对常规混凝-沉淀-过滤工艺、臭氧生物活性炭和直接超滤等深度处理技术处理城市污水处理厂二级出水的效果进行了试验研究,对各种工艺的去除效果进行了评价。     

Removal of heavy metal ions from water by complexation-assisted ultrafiltration

Toxic heavy metals in air, soil and water are global problems that are growing threat to the environment. Therefore, the removal and separation of toxic and environmentally relevant heavy metal ions are a technological challenge with respect to industrial and environmental application. A promising process for the removal of heavy metal ions from aqueous solutions involves bonding the metals to a bonding agent (such as macromolecular species), and then separating the loaded agents from wastewater by separation processes such as membrane filtration. The choice of water-soluble macroligands remains important for developing this technology. The effects of type of complexing agent, pH value and applied pressure on retention coefficients of Zn(II) and Cd(II) complexes were investigated. At best operating conditions (pH=9.0, p=300kPa) using diethylaminoethyl cellulose, the removal of Cd(2+) and Zn(2+) was more than 95% and 99%, respectively.     

Phytoextraction of lead-contaminated soil using vetivergrass (<Emphasis Type="Italic">Vetiveria zizanioides</Emphasis> L.), cogongrass (<Emphasis Type="Italic">Imperata cylindrica</Emphasis> L.) and carabaograss (<Emphasis Type="Italic">Paspalum conjugatum</Emphasis> L.)

Background, Aims and Scope The global problem concerning contamination of the environment as a consequence of human activities is increasing. Most of the environmental contaminants are chemical by-products and heavy metals such as lead (Pb). Lead released into the environment makes its way into the air, soil and water. Lead contributes to a variety of health effects such as decline in mental, cognitive and physical health of the individual. An alternative way of reducing Pb concentration from the soil is through phytoremediation. Phytoremediation is an alternative method that uses plants to clean up a contaminated area. The objectives of this study were: (1) to determine the survival rate and vegetative characteristics of three grass species such as vetivergrass, cogongrass and carabaograss grown in soils with different Pb levels; and (2) to determine and compare the ability of the three grass species as potential phytoremediators in terms of Pb accumulation by plants. Methods The three test plants: vetivergrass (Vetiveria zizanioides L.); cogongrass (Imperata cylindrica L.); and carabaograss (Paspalum conjugatum L.) were grown in individual plastic bags containing soils with 75 mg kg⁻¹ (37.5 kg ha⁻¹) and 150 mg kg⁻¹ (75 kg ha⁻¹) of Pb, respectively. The Pb contents of the test plants and the soil were analyzed before and after experimental treatments using an atomic absorption spectrophotometer. This study was laid out following a 3 × 2 factorial experiment in a completely randomized design. Results On the vegetative characteristics of the test plants, vetivergrass registered the highest whole plant dry matter weight (33.85–39.39 Mg ha⁻¹). Carabaograss had the lowest herbage mass production of 4.12 Mg ha⁻¹ and 5.72 Mg ha⁻¹ from soils added with 75 and 150 mg Pb kg⁻¹, respectively. Vetivergrass also had the highest percent plant survival which meant it best tolerated the Pb contamination in soils. Vetivergrass registered the highest rate of Pb absorption (10.16 ± 2.81 mg kg⁻¹). This was followed by cogongrass (2.34 ± 0.52 mg kg⁻¹) and carabaograss with a mean Pb level of 0.49 ± 0.56 mg kg⁻¹. Levels of Pb among the three grasses (shoots + roots) did not vary significantly with the amount of Pb added (75 and 150 mg kg⁻¹) to the soil. Discussion Vetivergrass yielded the highest biomass; it also has the greatest amount of Pb absorbed (roots + shoots). This can be attributed to the highly extensive root system of vetivergrass with the presence of an enormous amount of root hairs. Extensive root system denotes more contact to nutrients in soils, therefore more likelihood of nutrient absorption and Pb uptake. The efficiency of plants as phytoremediators could be correlated with the plants’ total biomass. This implies that the higher the biomass, the greater the Pb uptake. Plants characteristically exhibit remarkable capacity to absorb what they need and exclude what they do not need. Some plants utilize exclusion mechanisms, where there is a reduced uptake by the roots or a restricted transport of the metals from root to shoots. Combination of high metal accumulation and high biomass production results in the most metal removal from the soil. Conclusions The present study indicated that vetivergrass possessed many beneficial characteristics to uptake Pb from contaminated soil. It was the most tolerant and could grow in soil contaminated with high Pb concentration. Cogongrass and carabaograss are also potential phytoremediators since they can absorb small amount of Pb in soils, although cogongrass is more tolerant to Pb-contaminated soil compared with carabaograss. The important implication of our findings is that vetivergrass can be used for phytoextraction on sites contaminated with high levels of heavy metals; particularly Pb. Recommendations and Perspectives High levels of Pb in localized areas are still a concern especially in urban areas with high levels of traffic, near Pb smelters, battery plants, or industrial facilities that burn fuel ending up in water and soils. The grasses used in the study, and particularly vetivergrass, can be used to phytoremediate urban soil with various contaminations by planting these grasses in lawns and public parks. ESS-Submission Editor: Dr. Willie Peijnenburg (wjgm.peijnenburg@rivm.nl)     

Clonal variation in heavy metal accumulation and biomass production in a poplar coppice culture: I. Seasonal variation in leaf, wood and bark concentrations

The use of plants to decontaminate soils polluted by heavy metals has received considerable attention in recent years as a low-cost technique. Poplars (Populus spp.) can accumulate relatively high levels of certain metals, and have the added advantage of producing biomass that can be used for energy production. A short rotation coppice culture with 13 poplar clones was established on a former waste disposal site, which was moderately polluted with heavy metals. Total content of metals in leaves, wood and bark were determined in August and October/November. Significant clonal differences in accumulation were found for most metals, although clones with the highest concentration of all metals were not found. Cadmium, zinc and aluminium were most efficiently taken up. The lowest concentration was found in wood; the highest concentrations were generally found in senescing leaves, making removal and treatment of fallen leaves necessary.     

Trace metal speciation and fluxes within a major French wastewater treatment plant: impact of the successive treatments stages

Seven metals (Cd, Co, Cr, Cu, Fe, Ni and Pb) were monitored at the Seine-Aval wastewater treatment plant during 6 sampling campaigns in April 2004. Particulate and dissolved metals have been measured in 24 h composite samples at each treatment stage (primary settling, secondary activated sludge and tertiary flocculation by FeCl₃). In addition, the diffusive gradient in thin film technique (DGT) was used to determine the dissolved inert and labile metal fraction. Although all treatment stages were able to decrease particulate metals concentrations in wastewater, most dissolved metals concentrations were mainly affected during primary settling. This unexpected result was attributed to tertiary sludge filtrate recirculation. Metals added via the FeCl₃ reagent at the tertiary treatment were shown to lower the overall Cr removal from wastewater and to enrich Ni in effluents. The plant operating conditions (recirculation and reagent addition) appear therefore as important as treatment processes for the metals removal. Total metal fluxes were highly decreased by the whole treatment plant for Cd, Cr, Cu and Pb and to a lesser extend for Co and Ni. However, the labile metal fluxes were poorly decreased for Cu (18%), not significantly decreased for Ni and increased for Fe. The labile fraction of Cd, Co and Cr was not detectable at any stage of the plant. Discharged labile fluxes, at least for Ni, were potentially significant compared to the labile metal fluxes in the river measured downstream the plant. Treated urban wastewater discharges should be carefully considered as a possible source of bioavailable trace metals.     

动电修复不同形态重金属污染土壤效果研究

以钢铁厂附近废地的重金属土壤为对象,研究了动电修复技术去除重金属效果与其各化学形态的关系,讨论了电能消耗。结果表明,同一种重金属,其动电去除效率顺序为交换态碳酸盐结合态Fe-Mn氧化结合态有机结合态残留态,即吸附性越弱的形态,其去除率越高,如交换态去除率95%;吸附性越强的形态,其去除率越低,如有机态和残留态去除率低于29%;对于不同重金属,高移动性和弱吸附性的重金属较弱移动性和强吸附性的重金属去除效果好,即各形态的Cd、Cu和Zn的去除率明显高于相应形态Pb的去除率;能耗分析表明,实验时间超过96 h后,在电能有较大消耗的同时,重金属去除率却提高不明显。     

Filter materials for metal removal from mine drainage—a review

A large number of filter materials, organic and inorganic, for removal of heavy metals in mine drainage have been reviewed. Bark, chitin, chitosan, commercial ion exchangers, dairy manure compost, lignite, peat, rice husks, vegetal compost, and yeast are examples of organic materials, while bio-carbons, calcareous shale, dolomite, fly ash, limestone, olivine, steel slag materials and zeolites are examples of inorganic materials. The majority of these filter materials have been investigated in laboratory studies, based on various experimental set-ups (batch and/or column tests) and different conditions. A few materials, for instance steel slag materials, have also been subjects to field investigations under real-life conditions. The results from these investigations show that steel slag materials have the potential to remove heavy metals under different conditions. Ion exchange has been suggested as the major metal removal mechanisms not only for steel slag but also for lignite. Other suggested removal mechanisms have also been identified. Adsorption has been suggested important for activated carbon, precipitation for chitosan and sulphate reduction for olivine. General findings indicate that the results with regard to metal removal vary due to experimental set ups, composition of mine drainage and properties of filter materials and the discrepancies between studies renders normalisation of data difficult. However, the literature reveals that Fe, Zn, Pb, Hg and Al are removed to a large extent. Further investigations, especially under real-life conditions, are however necessary in order to find suitable filter materials for treatment of mine drainage.     

Preparation of macromolecular heavy metal coagulant and treatment of wastewater containing copper.

Many treatment technologies for wastewater containing heavy metals have been developed in recent years, but these technologies have some disadvantages, such as poor removing efficiency and complex operation. For this reason, a macromolecular heavy metal coagulant polyethyleneimine-sodium xanthogenate (PEX) was prepared by grafting a xanthogenate group to polyethyleneimine. It was determined that PEX has the function of removing both turbidity and copper ions. It was also determined that copper ions and turbidity have a cooperative removal effect with each other in the process of treating wastewater containing both turbidity and copper ions by PEX. The investigation showed that PEX is an amphoteric polyelectrolyte. At lower pH values, the amino groups of the macromolecule are electrically positive; therefore, turbidity is removed because of electroneutralization coagulation; at higher pH values, both amino groups and xanthogenic radical groups contribute to the removal of heavy metals, as a result of chelation. Compared with traditional chemical precipitation by calcium oxide and coagulation by an ordinary inorganic coagulant, PEX showed obvious advantages, for example, removing both turbidity and copper ions, higher removal efficiency, lower suitable pH value, and higher floc settlement velocity.