Dissipation of terbuthylazine,metolachlor, and mesotrione in soils with contrasting texture

ABSTRACT

This study evaluates the dissipation of terbuthylazine, metolachlor, and mesotrione at different depths in soils with contrasting texture. The field trial was conducted at the Padua University Experimental Farm, north-east Italy. The persistence of three herbicides was studied in three different soil textures (clay soil, sandy soil, and loamy soil) at two depths (0–5 and 5–15 cm). Soil organic carbon content was highest in the clay (1.10%) followed by loam (0.67%) and sandy soil (0.24%); the pH of soils was sub-alkaline. Terbuthylazine, metolachlor, and mesotrione were applied on maize as a formulated product (Lumax®) at a dose of 3.5 L ha^?1. Their dissipation in the treated plots was followed for 2 months after application. The concentrations of herbicides were analyzed by liquid chromatography-mass spectrometry. The dissipation of terbuthylazine, metolachlor, and mesotrione could be described by a pseudo first-order kinetics. Terbuthylazine showed the highest DT50, followed by metolachlor and mesotrione. Considering the tested soil, the highest DT50 value was found in clay soil for terbuthylazine and metolachlor, whereas for mesotrione there was no difference among soils. Significant differences were found between the two soil depths for terbuthylazine and metolachlor, whereas none were found for mesotrione. These results suggest that soil texture and depth have a strong influence on the dissipation of terbuthylazine and metolachlor, whereas no influence was observed on mesotrione because of its chemical and physical properties.     

Behavior of 1,3-dichloropropene and methyl isothiocyanate in undisturbed soil columns

To develop alternatives to methyl bromide (MeBr) for soil disinfection under environmental Moroccan conditions, distribution and persistence of 1,3-dichloropropene (1,3-D) and methyl isothiocyanate (MITC) were tested in undisturbed soil columns (12 cm internal diameter, 1 m length). 1,3-D was injected at a 15 cm depth and directly followed by metam-sodium (a precursor of MITC), which was applied at the soil surface of the same column using a peristaltic pump. Concerning the distribution of these fumigants in the soil profiles, our results showed that 24 h after treatment, 1,3-D and MITC were concentrated at the 0-40 cm soil layers, and reached the deeper layers 48 h later. MITC and 1,3-D dissipation was studied and the half-life (DT50) measured were 6.5 and 8 days, respectively. Total volatilization losses reached 9% for MITC and 28% for 1,3-D. MITC and 1,3-D volatilization was found to be influence by soil water contents.The results show that by reducing volatilization, photodegradation and leaching of these fumigants a suitable alternative to MeBr use is offered.     

Emission, distribution and leaching of methyl isothiocyanate and chloropicrin under different surface containments

The environmental fate of fumigants methyl isothiocyanate (MITC) and chloropicrin (CP) is of great concern for potential air and groundwater contamination while retaining sufficient concentrations for pest control efficacy. The emission, gas phase distribution, leaching, and persistence of MITC and CP were examined in repacked columns filled with sandy soils under three surface conditions: tarp without irrigation, tarp with limited irrigation, and 5-d irrigation without tarp cover. For MITC, cumulative emission constituted 62%, 36%, and 0.3% of the amount applied under tarp without irrigation, tarp with limited irrigation, and 5-d irrigation without tarp surface conditions, respectively. The corresponding cumulative emission losses were 45%, 30%, and 5.4% for CP. During the first 24h after injection, soil air concentrations of the two fumigants were much higher in the 15-25cm depth range than other depths in the soil profile. Small amounts of leaching occurred for both fumigants, indicating potential for groundwater contamination should heavy rain fall or irrigation occurs immediately after soil fumigation. Very small amounts of residual MITC and CP (<2%) were found in the soil 24 days after the experiment. The study clearly showed that atmospheric emission and degradation were the two primary pathways of MITC and CP dissipation during soil fumigation. Emission could be effectively reduced with 5-d irrigation if small leaching is acceptable or be prevented.     

Atmospheric flux of agricultural fumigants from raised-bed,plastic-mulch crop production systems

Atmospheric emission of methyl isothiocyanate (MITC), chloropicrin (CP), 1,3-dichloropropene (1,3-D), and dimethyl disulfide (DMDS) were measured in the field under fumigant application scenarios representative of raised bed–plastic-mulched crop production systems. For three fumigation sites located in Florida, cumulative emissions of 1,3-D, MITC and CP were less than 11%, 6% and 2%, respectively. For three fumigation sites in located in Georgia, cumulative emissions of MITC and CP were <13% and 12%, respectively while DMDS emissions varied from 37% to 95%. In the Florida sites, emission peak flux of CP occurred within the first 6 h after application. Peak emission of 1,3-D and MITC occurred between 100 and 144 h after application. In the Georgia sites where fumigated soil was covered by low density polyethylene (LDPE) plastic, emission peak flux of DMDS and MITC occurred between 12and 48 h after application. Key factors affecting atmospheric emissions were soil moisture, soil tilth and the resistance to fumigant diffusion of the plastic film used to cover soil following application. This study demonstrated reduced atmospheric emissions of agricultural fumigants under commercial production conditions when applied using good agricultural practices including soil water contents above field capacity, uniform soil tilth in the fumigation zone and the use of metalized or virtually impermeable films to further reduce fumigant emissions. The results of this study show a need for regional flux studies due to the various interactions of soil and climate with local agricultural land management practices.     

Mineralisation studies of 14C-labelled metsulfuron-methyl, tribenuron-methyl, chlorsulfuron and thifensulfuron-methyl in one Danish soil and groundwater sediment profile.

Bacterial mineralisation of four sulfonylurea herbicides at 20 microg kg(-1) in a sandy soil from nine different depths in a sandy soil horizon (5-780 cm) was investigated in laboratory studies. Metsulfuron-methyl, chlorsulfuron, and tribenuron-methyl were 14C-labelled in the sulfonamide ring, while thifensulfuron-methyl was labelled in the thiophene ring. The highest mineralised amount in 126 days was observed for metsulfuron-methyl (40%) followed by tribenuron-methyl (25%), and thifensulfuron-methyl (11%). Chlorsulfuron showed low mineralisation in all the soils tested (<4%). Mineralisation of the herbicides metsulfuron-methyl and tribenuron-methyl varied according to soil depth (upper profile: 5-70 cm, and lower profile: 165-780 cm) and were proven faster in soil taken from depths 5-7 and 30-35 cm, and slower in depths 45-50 and 70-75 cm. Mineralisation was absent in the lower profile (165-780 cm). As an indicator of microbial activity bacterial counts were taken at the experimental start; these counts grouped in three levels: highest in the surface layer (5-7 cm), slightly lower in the depths 30-75 cm, and lowest in the lower profile (165-780 cm). Residual concentrations of metsulfuron-methyl correlated to the accumulated amount mineralised, with high residual concentrations in soil showing low mineralisation. Also chlorsulfuron showed high residual concentrations with increasing depth in the upper profile, but the relatively high dissipation at 30-35 cm and lower one at 45-50 cm could not be related with the lack of mineralisation. This shows that hydrolysis occurs, but mineralisation of the chloro-substituted sulfonamide is restricted. Tribenuron-methyl and thifensulfuron-methyl could not be detected due to interference with other compounds.     

Atmospheric volatilization and distribution of (Z)- and (E)-1,3-dichloropropene in field beds with and without plastic covers

The fumigant 1,3-dichloropropene (1,3-D) is considered to be a potential replacement for methyl bromide when methyl bromide is phased out in 2005. This study on surface emissions and subsurface diffusion of 1,3-D in a Florida sandy soil was conducted in field beds with or without plastic covers. After injection of the commercial fumigant Telone II by conventional chisels to field beds at 30cm depth which were covered with polyethylene film (PE), virtually impermeable film, or no cover (bare), (Z)- and (E)-1,3-D rapidly diffused upward. Twenty hours after injection, majority of (Z)- and (E)-1,3-D had moved upward from 30 cm depth to the layer of 5-20 cm depth. Downward movement of the two isomers in the beds with or without a plastic cover was not significant. (Z)-1,3-D diffused more rapidly than (E)-1,3-D. Virtually impermeable films (VIF) had a good capacity to retain (Z)- and (E)-1,3-D in soil pore air space. Vapor concentrations of the two isomers in the shallow subsurface of the field bed covered with VIF were greater than that in the two beds covered with polyethylene film (PE) or no cover (bare). In addition, VIF cover provided more uniform distribution of (Z)- and (E)-1,3-D in shallow subsurface than PE cover or no cover. Virtually impermeable film also had a better capability to retard surface emissions of the two isomers from soil in field beds than PE cover or no cover.     

Atmospheric Volatilization and Distribution of (Z)- and (E)-1,3-Dichloropropene in Field Beds with and without Plastic Covers

Abstract

The fumigant 1,3-dichloropropene (1,3-D) is considered to be a potential replacement for methyl bromide when methyl bromide is phased out in 2005. This study on surface emissions and subsurface diffusion of 1,3-D in a Florida sandy soil was conducted in field beds with or without plastic covers. After injection of the commercial fumigant Telone II by conventional chisels to field beds at 30 cm depth which were covered with polyethylene film (PE), virtually impermeable film, or no cover (bare), (Z)- and (E)-1,3-D rapidly diffused upward. Twenty hours after injection, majority of (Z)- and (E)-1,3-D had moved upward from 30 cm depth to the layer of 5–20 cm depth. Downward movement of the two isomers in the beds with or without a plastic cover was not significant. (Z)-1,3-D diffused more rapidly than (E)-1,3-D. Virtually impermeable films (VIF) had a good capacity to retain (Z)- and (E)-1,3-D in soil pore air space. Vapor concentrations of the two isomers in the shallow subsurface of the field bed covered with VIF were greater than that in the two beds covered with polyethylene film (PE) or no cover (bare). In addition, VIF cover provided more uniform distribution of (Z)- and (E)-1,3-D in shallow subsurface than PE cover or no cover. Virtually impermeable film also had a better capability to retard surface emissions of the two isomers from soil in field beds than PE cover or no cover.     

Herbicide movement and dissipation at four Midwestern sites

This study was conducted to evaluate atrazine (2-chloro-4-ethylamino-6-isopropyl-1,3,5-triazine) and alachlor (2-chloro-N-(methoxymethyl)acetamide) dissipation and movement to shallow aquifers across the Northern Sand Plains region of the United States. Sites were located at Minnesota on a Zimmerman fine sand, North Dakota on Hecla sandy loam, South Dakota on a Brandt silty clay loam, and Wisconsin on a Sparta sand. Herbicide concentrations were determined in soil samples taken to 90 cm four times during the growing season and water samples taken from the top one m of aquifer at least once every three months. Herbicides were detected to a depth of 30 cm in Sparta sand and 90 cm in all other soils. Some aquifer samples from each site contained atrazine with the highest concentration in the aquifer beneath the Sparta sand (1.28 microg L(-1)). Alachlor was detected only once in the aquifer at the SD site. The time to 50% atrazine dissipation (DT50) in the top 15 cm of soil averaged about 21 d in Sparta and Zimmerman sands and more than 45 d for Brandt and Hecla soils. Atrazine DT50 was correlated positively with % clay and organic carbon (OC), and negatively with % fine sand. Alachlor DT50 ranged from 12 to 32 d for Zimmerman and Brandt soils, respectively, and was correlated negatively with % clay and OC and positively with % sand.     

Paraquat adsorption, degradation, and remobilization in tropical soils of Thailand

Paraquat adsorption, degradation, and remobilization were investigated in representative tropical soils of Yom River Basin, Thailand. Adsorption of paraquat in eight soil samples using batch equilibration techniques indicated that adsorption depended on soil characteristics, including exchangeable basic cations and iron content. Multiple regression analysis indicated significant contribution of exchangeable calcium percentage (ECP), total iron content (TFe) and exchangeable sodium percentage (ESP) to paraquat sorption (Q). ESP and TFe were significant at all adsorption stages, whereas ESP was significant only at the initial stage of paraquat adsorption. Adsorption studies using two soils representing clay and sandy loam textures showed that paraquat adsorption followed the Freundlich model, exhibiting a nonlinear sorption curve. Paraquat adsorption was higher in the clay soil compared to the sandy loam soil with Kf values of 787 and 18, respectively. Desorption was low with 0.04 to 0.17% and 0.80 to 5.83% desorbed in clay and sandy loam soil, respectively, indicating some hysteresis effect. Time-dependent paraquat adsorption fitted to the Elovich kinetic model indicated that diffusion was a rate-limiting process. Paraquat mobility and degradation studies conducted using both field and laboratory soil column experiments with clay soil showed low mobility of paraquat with accumulation only in the surface 0-5 cm layer under field conditions and in the 0-1 cm layer in a laboratory soil column experiment. Degradation of paraquat in soil was faster under field conditions than at ambient laboratory conditions. The degradation rate followed a first-order kinetic model with the DT50 at 36-46 days and DT90 around 119-152 days.     

Aflatoxin decomposition in various soils

The persistence of aflatoxin in the soil environment could potentially result in a number of adverse environmental consequences. To determine the persistence of aflatoxin in soil, 14C-labeled aflatoxin B1, was added to silt loam, sandy loam, and silty clay loam soils and the subsequent release of 14CO2 was determined. After 120 days of incubation, 8.1% of the original aflatoxin added to the silt loam soil was released as CO2. Aflatoxin decomposition in the sandy loam soil proceeded more quickly than the other two soils for the first 20 days of incubation. After this time, the decomposition rate declined and by the end of the study, 4.9% of the aflatoxin was released as CO2. Aflatoxin decomposition proceeded most slowly in the silty clay loam soil. Only 1.4% of aflatoxin added to the soil was released as CO2 after 120 days incubation. To determine whether aflatoxin was bound to the silty clay loam soil, aflatoxin B1 was added to this soil and incubated for 20 days. The soil was periodically extracted and the aflatoxin species present were determined using thin layer chromatographic (TLC) procedures. After one day of incubation, the degradation products, aflatoxins B2 and G2, were observed. It was also found that much of the aflatoxin extracted from the soil was not mobile with the TLC solvent system used. This indicated that a conjugate may have formed and thus may be responsible for the lack of aflatoxin decomposition.     

Dynamic chemical characteristics of soil solution after pig manure application: A column study

When manures from intensive livestock operations are applied to agricultural or vegetable fields at a high rate, large amounts of salts and metals will be introduced into soils. Using a column leaching experiment, this study assessed the leaching potential of the downward movement of Cu and Zn as well as some salt ions after an intensive farm pig manure at rates of 0%, 5% and 10% (w/w) were applied to the top 20 cm of two different textured soils (G soil -sandy loam soil; H soil-silty clay loam soil), and investigated the growth of amaranth and Cu and Zn transfer from soil to amaranth (Amaranthus tricolor). Soil solutions were obtained at 20, 40 and 60 cm depth of the packed column and analyzed for pH, electrical conductivity (EC), dissolved organic matter (DOC) and Cu and Zn concentrations. The results indicated that application of pig manure containing Cu and Zn to sandy loam soil might cause higher leaching and uptake risk than silty clay loam soil, especially at high application rates. And manure amendment at 5% and 10% significantly decreased the biomass of amaranth, in which the salt impact rather than Cu and Zn toxicity from manures played more important role in amaranth growth. Thus the farmer should avoid application the high rate of pig manure containing metal and salt to soil at a time, especially in sandy soil.     

Paraquat Adsorption,Degradation, and Remobilization in Tropical Soils of Thailand

Paraquat adsorption, degradation, and remobilization were investigated in representative tropical soils of Yom River Basin, Thailand. Adsorption of paraquat in eight soil samples using batch equilibration techniques indicated that adsorption depended on soil characteristics, including exchangeable basic cations and iron content. Multiple regression analysis indicated significant contribution of exchangeable calcium percentage (ECP), total iron content (TFe) and exchangeable sodium percentage (ESP) to paraquat sorption (Q). ESP and TFe were significant at all adsorption stages, whereas ESP was significant only at the initial stage of paraquat adsorption. Adsorption studies using two soils representing clay and sandy loam textures showed that paraquat adsorption followed the Freundlich model, exhibiting a nonlinear sorption curve. Paraquat adsorption was higher in the clay soil compared to the sandy loam soil with K _f values of 787 and 18, respectively. Desorption was low with 0.04 to 0.17% and 0.80 to 5.83% desorbed in clay and sandy loam soil, respectively, indicating some hysteresis effect. Time-dependent paraquat adsorption fitted to the Elovich kinetic model indicated that diffusion was a rate-limiting process. Paraquat mobility and degradation studies conducted using both field and laboratory soil column experiments with clay soil showed low mobility of paraquat with accumulation only in the surface 0–5 cm layer under field conditions and in the 0–1 cm layer in a laboratory soil column experiment. Degradation of paraquat in soil was faster under field conditions than at ambient laboratory conditions. The degradation rate followed a first-order kinetic model with the DT₅₀ at 36–46 days and DT₉₀ around 119–152 days.     

Dynamic chemical characteristics of soil solution after pig manure application: a column study

When manures from intensive livestock operations are applied to agricultural or vegetable fields at a high rate, large amounts of salts and metals will be introduced into soils. Using a column leaching experiment, this study assessed the leaching potential of the downward movement of Cu and Zn as well as some salt ions after an intensive farm pig manure at rates of 0%, 5% and 10% (w/w) were applied to the top 20 cm of two different textured soils (G soil -sandy loam soil; H soil-silty clay loam soil), and investigated the growth of amaranth and Cu and Zn transfer from soil to amaranth (Amaranthus tricolor). Soil solutions were obtained at 20, 40 and 60 cm depth of the packed column and analyzed for pH, electrical conductivity (EC), dissolved organic matter (DOC) and Cu and Zn concentrations. The results indicated that application of pig manure containing Cu and Zn to sandy loam soil might cause higher leaching and uptake risk than silty clay loam soil, especially at high application rates. And manure amendment at 5% and 10% significantly decreased the biomass of amaranth, in which the salt impact rather than Cu and Zn toxicity from manures played more important role in amaranth growth. Thus the farmer should avoid application the high rate of pig manure containing metal and salt to soil at a time, especially in sandy soil.     

Herbicide movement and dissipation at four midwestern sites

Abstract

This study was conducted to evaluate atrazine (2‐chloro‐4‐ethylamino‐6‐isopropyl‐1, 3, 5‐triazine) and alachlor (2‐chIoro‐N‐(methoxymethyl)acetamide) dissipation and movement to shallow aquifers across the Northern Sand Plains region of the United States. Sites were located at Minnesota on a Zimmerman fine sand, North Dakota on Hecla sandy loam, South Dakota on a Brandt silty clay loam, and Wisconsin on a Sparta sand. Herbicide concentrations were determined in soil samples taken to 90 cm four times during the growing season and water samples taken from the top one m of aquifer at least once every three months. Herbicides were detected to a depth of 30 cm in Sparta sand and 90 cm in all other soils. Some aquifer samples from each site contained atrazine with the highest concentration in the aquifer beneath the Sparta sand (1.28 μg L^‐1). Alachlor was detected only once in the aquifer at the SD site. The time to 50% atrazine dissipation (DT₅₀) in the top 15 cm of soil averaged about 21 d in Sparta and Zimmerman sands and more than 45 d for Brandt and Hecla soils. Atrazine DT₅₀ was correlated positively with % clay and organic carbon (OC), and negatively with % fine sand. Alachlor DT₅₀ ranged from 12 to 32 d for Zimmerman and Brandt soils, respectively, and was correlated negatively with % clay and OC and positively with % sand.     

Persistence of metsulfuron‐methyl in two soils

Abstract

The persistence of metsulfuron‐methyl in sandy loam and clay soil incubated at different temperatures and moistures contents was investigated under laboratory conditions using longbean (Vigna sesquipedalis L.) as bioassay species. A significant degradation of metsulfuron‐methyl was observed in non‐autoclaved soil rather than the autoclaved soil sample. At higher temperature, the degradation rate in non‐autoclaved soil improved with increasing soil moisture content. In non‐autoclaved sandy loam and clay soil, the half‐life was reduced from 9.0 to 5.7 and from 11.2 to 4.6 days, respectively when moisture level of sandy loam increased from 20 to 80% field capacity at 35°C. In the autoclaved soil, herbicide residue seems to have been broken down by non‐biological process. The rate of dissipation was slightly increased after the second application of the herbicide to non‐autoclaved soils but not in autoclaved soil, indicating the importance of microorganisms in the breakdown process.     

Aflatoxin decomposition in various soils

Abstract

The persistence of aflatoxin in the soil environment could potentially result in a number of adverse environmental consequences. To determine the persistence of aflatoxin in soil, ¹⁴C‐labeled aflatoxin B₁, was added to silt loam, sandy loam, and silty clay loam soils and the subsequent release of ¹⁴CO₂ was determined. After 120 days of incubation, 8.1% of the original aflatoxin added to the silt loam soil was released as CO₂ ? Aflatoxin decomposition in the sandy loam soil proceeded more quickly than the other two soils for the first 20 days of incubation. After this time, the decomposition rate declined and by the end of the study, 4.9% of the aflatoxin was released as CO_2. Aflatoxin decomposition proceeded most slowly in the silty clay loam soil. Only 1.4% of aflatoxin added to the soil was released as CO₂ after 120 days incubation. To determine whether aflatoxin was bound to the silty clay loam soil, aflatoxin B₁ was added to this soil and incubated for 20 days. The soil was periodically extracted and the aflatoxin species present were determined using thin layer chromatographic (TLC) procedures. After one day of incubation, the degradation products, aflatoxins B₂ and G₂, were observed. It was also found that much of the aflatoxin extracted from the soil was not mobile with the TLC solvent system used. This indicated that a conjugate may have formed and thus may be responsible for the lack of aflatoxin decomposition.     

Fate of the herbicide 14C-terbuthylazine in Brazilian soils under various climatic conditions

14C-terbuthylazine was applied to three Brazilian soils in closed aerated laboratory microcosms, both under standardized and under natural Brazilian climate conditions. Volatilization from soil to air, leaching from soil to percolate water, and transport from upper to deeper soil layers were higher in sandy soil than in clay soil and in organic soil. Mineralization of 14C-terbuthylazine to 14CO2 was higher in sandy soil than in clay and organic soils under standardized climatic conditions, whereas it was higher in organic soil than in sandy soil under Brazilian summer conditions. Under natural Brazilian summer conditions, leaching as well as vertical transport within the soil were enhanced as compared to standardized climate conditions comprising lower precipitation rates; volatilization was strongly reduced under high irrigation conditions.     

Volatilization of 1,2-dibromo-3-chloropropane (DBCP) from soils.

The volatilization of DBCP from soils, as affected by the soil characteristics and application techniques, was studied in a laboratory experiment. The volatilization rate of DBCP applied in water was higher from sandy and silty loam soils than from clay soil. Water added after DBCP application acted as a soil cover, decreasing the volatilization rate. The results obtained with DBCP application in hexane to air-dry soils, indicate that adsorption could be an important factor in reducing the volatilization losses. Diffusion coefficients were calculated from the volatilization parameters, by using a simplified relationship between volatilization losses and diffusion through soil.     

Loss of HCH from surface soil layers under subtropical conditions

The loss of HCH (hexachlorocyclohexane) at an application rate of 25 kg ha(-1) was studied under field conditions from two surface soil layers, each of 7.5 cm, at two sites in Delhi. The soil at both sites was sandy loam type, with a pH of 8.2, and 0.8 to 1.0% organic matter content. At site 1, which was kept fallow and not watered, the upper 7.5-cm layer of soil initially lost HCH more rapidly than the lower layer. The half-life of the HCH in the upper and lower 7.5-cm layers was 21 and 41 days, respectively, and it was 26 days for the total HCH in the combined 15-cm soil layer. At site 2, which contained ornamental plants and was watered regularly, there was not much difference in the loss of HCH between the upper and lower layers. The half-life of HCH was 17 and 25 days for the upper and lower 7.5-cm layers, respectively, and it was 20 days for the total 15-cm soil layer, at this site. The loss was greatest initially at the sites, and was faster in wet soil than in dry soil.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg(-1) degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg(-1) application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to >70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of (14)C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative (14)CO(2) was less than 1.5% of applied (14)C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.