Thermal properties of dioxins, furans and related compounds

Vapor pressures are important parameters for modeling of environmental fate and incineration behaviour of chloro-dibenzodioxins and -dibenzofurans. Vapor pressures, enthalpies and entropies of sublimation were measured for four dibenzofurans and were compared to corresponding data on chlorodioxins. A vapor pressure correlation method, which uses the liquid phases as reference states was introduced. Boiling points, enthalpies and entropies of fusion could be calculated from the vapor pressure data by this method. The determined parameters were correlated with the degree of chlorine substitution and the correlations permit the estimation of boiling points, enthalpies of fusion and of sublimation pressures of n-chlorodioxins and -furans of known melting points. The predicted vapor pressures of 2,3,7,8-TCDD were found to be in good agreement with literature reportings.     

Relationships between aqueous solubility and octanol-water partition coefficients

The physical chemical equations relating solubility to octanol water partition coefficient are presented and used to develop a new correlation between these quantities which includes a melting point (fugacity ratio) correction. The correlation is satisfactory for 45 organic compounds but it is not applicable to organic acids. When applied to very high molecular weight (> 290) compounds the correlation is less satisfactory; either it is believed because the data are inaccurate or because the tendency for these compounds to partition into organic phases is less than expected. This may have profound environmental implications.     

Modeling solubility of CO<Subscript>2</Subscript>/hydrocarbon gas in ionic liquid ([emim][FAP]) using Aspen Plus simulations

The Peng-Robinson equation of state with quadratic van der Waals (vdW) mixing rule model was chosen to perform the thermodynamic calculations in Flash3 column of Aspen Plus to predict the solubility of CO₂ or any one of the hydrocarbons (HCs) among methane, ethane, propane, and butane in an ionic liquid 1-ethyl-3-methylimidazolium tris(pentafluoroethyl)trifluorophosphate ([emim][FAP]). Bubble point pressure, solubility, bubble point temperature, fugacity, and partial molar volume at infinite dilution were obtained from the simulations, and enthalpy of absorption, Gibbs free energy of solvation, and entropy change of absorption were estimated by thermodynamic relations. Results show that carbon chain length has a significant effect on the bubble point pressure. Methane has the highest bubble point pressure among all the considered HCs and CO₂. The bubble point pressure and fugacity variation with temperature is different for CO₂ as compared to HCs for mole fractions above 0.2. Two different profiles are noticed for enthalpy of absorption when plotted as a function of mole fraction of gas soluble in IL. Partial molar volume of CO₂ decreases with increase in temperature in [emim][FAP], while it is increased for HCs. Bubble point temperature decreases with increase in the mole fraction of the solute. Entropy of solvation increases with temperature till a particular value followed by a decrease with further increase in temperature. Gibbs free energy change of solvation showed that the process of solubility was spontaneous.     

Application of reutilization technology to calcium fluoride sludge from semiconductor manufacturers

Glass ceramics were prepared from mixtures of wastes generated from refining of waste glass and semiconductor industrial wastewater sludge. The aim is then indeed to study the possible use and effects of integrating calcium fluoride (CaF2) as present in semiconductor wastewater sludge in the silica (glass) melts. CaF2 sludge was blended with a conditioner according to characteristics of the target. Calcium oxide-silicon dioxide-aluminum oxide system glass ceramics have relatively high melting points. Addition of CaF2 sludge to fluxes can significantly reduce the melting point and hence improve the kinetics of the reactions. CaF2 sludge and waste glass were co-melted in various ratios to elucidate their interactions at various heating temperatures. The results indicate that the lowest melting temperature was 1163 degrees C, obtained for the CaF2 sludge-waste glass mixture at a ratio 6:4 (wt:wt), which is significantly lower than that of CaF2 sludge (1378 degrees C). The benefits of using melting to dispose of sludge are the reduction of waste and the fixation of heavy metals. Heat treatment was used to convert the obtained glass into glass ceramics. Heavy metal leaching tests revealed that melting conditions lowered the heavy metal concentrations in the leachate to an order of magnitude lower than that in the sludge. Consequently, industrial sludge can be safely used as a fine aggregate material for a potentially wide range of construction applications.     

Temperature dependence of the infinite dilution activity coefficient and Henry's law constant of polycyclic aromatic hydrocarbons in water

The water solubility of 9,10-dihydroanthracene was experimentally determined between 278.12 and 313.17 K. Determinations were carried out by an experimental procedure developed in our laboratory, which is a modification of the dynamic coupled column liquid chromatographic technique. The uncertainty of the experimental determinations ranged from +/- 0.50% to +/- 3.10%. These data, as well as the water solubility data of other five polycyclic aromatic hydrocarbons (PAHs) previously studied, were used to calculate the temperature dependence of the infinite dilution activity coefficient of 9,10-dihydroanthracene, anthracene, pyrene, 9,10-dihydrophenanthrene, m-terphenyl, and guaiazulene in water. Molar excess enthalpies and entropies at infinite dilution, at 298.15 K, were also derived. The temperature dependence of the infinite dilution activity coefficients was used, together with literature values of the vapor pressures of supercooled liquid PAHs (p(B)(sc)), to estimate their Henry's law constants (HLC). Only HLC for anthracene, pyrene, and 9,10-dihydrophenanthrene were calculated, since no p(B)(sc) data were available in the literature for 9,10-dihydroanthracene, m-terphenyl, and guaiazulene. From the observed temperature dependence of the Henry's law constants the enthalpy and entropy of the phase change from the dissolved phase to the gas phase were also derived for anthracene, pyrene, and 9,10-dihydrophenanthrene.     

Fugacity modelling to predict the distribution of organic contaminants in the soil:oil matrix of constructed biopiles

Level I and II fugacity approaches were used to model the environmental distribution of benzene, anthracene, phenanthrene, 1-methylphenanthrene and benzo[a]pyrene in a four phase biopile system, accounting for air, water, mineral soil and non-aqueous phase liquid (oil) phase. The non-aqueous phase liquid (NAPL) and soil phases were the dominant partition media for the contaminants in each biopile and the contaminants differed markedly in their individual fugacities. Comparison of three soils with different percentage of organic carbon (% org C) showed that the % org C influenced contaminant partitioning behaviour. While benzene showed an aqueous concentration worthy of note for leachate control during biopiling, other organic chemicals showed that insignificant amount of chemicals leached into the water, greatly reducing the potential extent of groundwater contamination. Level II fugacity model showed that degradation was the dominant removal process except for benzene. In all three biopile systems, the rate of degradation of benzo(a)pyrene was low, requiring more than 12 years for soil concentrations from a spill of about 25 kg (100 mol) to be reduced to a concentration of 0.001 microgg(-1). The removal time of 1-methylphenanthrene and either anthracene or phenanthrene was about 1 and 3 years, respectively. In contrast, benzene showed the highest degradation rate and was removed after 136 days in all biopile systems. Overall, this study confirms the association of risk critical contaminants with the residual saturation in treated soils and reinforces the importance of accounting for the partitioning behaviour of both NAPL and soil phases during the risk assessment of oil-contaminated sites.     

2,4-二氯苯酚在土壤中的吸附及其批实验与柱实验的分配系数比较

为了研究2,4-二氯苯酚在土壤中的吸附及比较其批实验与柱实验的分配系数Kd,开展了2,4-二氯苯酚的批实验（不同液固比条件下）和柱实验。通过分析结果可知,在批实验中,不同液固比条件下2,4-二氯苯酚达到平衡的时间类似,都在60～70 h,吸附动力学曲线符合伪二级动力学方程,吸附规律是：液固比越大,平衡吸附量增大,反应速率常数K2减小,初始吸附速率常数减小;Kd随液固比增大而降低,范围在2.91～2.12 L/kg。柱实验结果表明,2,4-二氯苯酚的贯穿曲线可以很好地用化学非平衡模型来拟合,通过模型拟合得到的Kd值要低于批实验的结果。该研究对表征2,4-二氯苯酚在环境中的行为、预测其对土壤和地下水的污染及其治理提供了依据。     

Modeling the dynamic changes in concentrations of gamma-hexachlorocyclohexane (gamma-HCH) in Tianjin region from 1953 to 2020

A level IV fugacity model was used to simulate the dynamic changes of gamma-hexachlorocyclohexane (gamma-HCH) concentrations in environmental media in Tianjin, China. A similar model (level III) was previously used and validated under steady state conditions; this paper explores its dynamic behavior. Application of the level IV fugacity model has been validated using independently observed gamma-HCH concentrations in various media during the early 1980s and during 2001. Sensitivity analysis was conducted using coefficient-of-variation normalized sensitivity coefficients. The model was also subject to uncertainty analysis using Monte Carlo simulation. It was found that concentrations of gamma-HCH reached within 95% of their steady-state levels in all media after less than 15 years. Around one order-of-magnitude decreases in gamma-HCH concentrations in various media occurred between 1993 and 2001. We project that gamma-HCH concentrations will decrease another 1.7-1.9 orders of magnitude to reach 1.1 (0.9-1.2) x 10(-14), 2.7 (2.5-3.0) x 10(-10), 1.2 (1.1-1.3) x 10(-7), and 6.1 (5.4-6.8) x 10(-8) mol/m(3), in air, water, soil, and sediment, respectively, by 2020. The sensitivities and true uncertainty of the model are discussed.     

The effectiveness of lime-based amendments and bauxite residues at removing phosphorus from piggery effluent

Piggery effluent may contribute to the eutrophication of waterways, if it is not treated before disposal, because of high levels of phosphorus. Limes and red muds (a residue from bauxite refining) were used to remove phosphorus from piggery effluent (41 mg litre(-1) total P). Lime-based amendments were more effective than the red muds at removing phosphorus when compared at the same liquid: solid ratios. Based on laboratory data, the cost of treating effluent increased rapidly as the final required phosphorus concentration decreased to less than 4 mg litre(-1). Kiln dust was the cheapest amendment tested down to 2 mg litre(-1). Hydrated lime was able to clarify and flocculate the effluent to 1 mg litre(-1) within 60 min. The re-useability of all limes may be determined by a simple pH test. Red mud could be used to remove phosphorus when its pH was lowered to 6.0-6.5 and it is used at liquid:solid ratios <20:1.     

Organochlorine pesticide air-water exchange and bioconcentration in krill in the Ross Sea

Mean hexachlorobenzene (HCB) and hexachlorocyclohexane (HCH) concentrations, measured in seawater and air samples, confirmed the decline in levels of these compounds in Antarctic air and water. However, low α/γ-HCH ratios in air at the beginning of the sampling period suggest a predominance of fresh lindane entering the Antarctic atmosphere during the Austral spring probably due to current use in the Southern Hemisphere. Water-air fugacity ratios demonstrate the potential for HCH gas deposition to coastal Antarctic seas, while the water-air fugacity ratios for HCB imply that volatilization does not account for the observed decrease of HCB in surface seawater. HCH concentrations found in krill samples were correlated with seawater concentrations indicative of bioconcentration of HCHs from seawater.     

Spatial variability in compartmental fate modelling

A new approach is presented which is designed to address the spatial heterogeneity of the environment in compartmental mass balance models of chemical fate in the environment. It rests on the assumption of chemical equilibration within one phase despite prevailing environmental heterogeneity. Composite D- and Z-values are derived from sub-unit specific environmental parameters and are used to solve mass balance equations which can be adopted essentially unchanged from existing compartmental fugacity models. With the resulting common fugacity value for each compartment, sub-unit specific concentrations and process rates can be calculated. The approach is illustrated using the QWASI lake model to calculate the fate of hexachlorobenzene in a hypothetical lake sub-divided in four distinct sub-units. The approach allows the subdivision of each compartment in a large number of sub-units with distinct environmental characteristics without substantially increasing model complexity. This is a necessary condition for linking fugacity models to geographical information systems.     

电镀污泥回收重金属的新工艺

合理、经济地处理混合电镀污泥,回收其中有价值的金属具有重要意义。以不同的酸作为浸出剂对电镀污泥中的金属进行了浸出效果实验。结果表明,在相同条件下,各酸的浸出效果顺序为:硫酸>盐酸>王水>硝酸;液体水与固体电镀污泥比为3,干污泥为5 g,硫酸加入量为15 mL,时间1 h条件下,混合电镀污泥中金属铜锌的浸出率最大,达到97.38%。分别采用铁和铁锰合金还原剂常温还原低熔点重金属离子铜、锌,浸出液中99%以上含量的铜、锌沉淀,使低熔点重金属与黑色金属铁、锰、铬有效分离。低熔点混合重金属可以用来做铜合金添加剂使用,最后沉淀的混合黑色金属氢氧化物处理后可以用来做炼钢合金添加剂使用。     

Evaluation of chloroform/methanol and dichloromethane/hexane extractable lipids as surrogate measures of sample partition capacity for organochlorines in fish tissues

Organic contaminant concentration data are often lipid normalized to provide an indication of the chemical fugacity in the sample or to compare the relative equilibrium status of samples from the same environment. This study compared lipid normalized PCB and organochlorine concentration data for tissues of individual fish when lipids were measured using chloroform/methanol (CM) or dichloromethane/hexane (DH) extractions. The CM extraction produced higher lipid yields for dorsal muscle (8-fold difference) and carcass (1.7-fold difference) compared to DH extractions, while both methods yielded comparable lipid contents for liver and adipose tissue. Lipid normalized tissue/carcass PCB and organochlorine concentration ratios were variable across tissue types when lipid contents from the CM technique were used, whereas, tissue/carcass concentration ratios approached the expected value of unity for each tissue when DH-derived lipids were used. These data suggest that the tissue lipid content as derived using the DH extraction provided a better surrogate measure of sample partition capacity than tissue lipids determined using the CM technique.     

Aqueous solubility and n-octanol/water partition coefficient correlations

Studies of the fate of chemicals require the knowledge of numerous parameters, among which of utmost importance are the water solubility and the n-octanol/water partition coefficient.

Numerous writers have demonstrated that there is a close correlation between these two parameters. The literature offers about fifteen cases of correlations between solubility and n-octanol/water partition coefficient with, for some of them, and for solids, a third variable: the fusion point. Unfortunately, the coefficients are often the results of theoretical considerations and the size of the data base is often small.

A study carried out on 300 products shows clearly the importance of the size of the data base. It is demonstrated that the coefficients obtained in practice are different from those which had been calculated theoretically. In particular, the introduction of a fusion point correction appears to be justified only to a limited extent.

This analysis has shown that there is a need to reexamine the theoretical approach and determine why the coefficients of the regression equation do not appear to adopt the values excepted from theoretical considerations.     

PTR-MS measurements and analysis of models for the calculation of Henry's law constants of monosulfides and disulfides

Sulfides are known for their strong odor impact even at very low concentrations. Here, we report Henry’s law constants (HLCs) measured at the nanomolar concentration range in water for monosulfides (dimethylsulfide, ethylmethylsulfide, diethylsulfide, allylmethylsulfide) and disulfides (dimethyldisulfide, diethylsulfide, dipropylsulfide) using a dynamic stripping technique coupled to Proton Transfer Reaction-Mass Spectrometry (PTR-MS). The experimental data were compared with literature values and to vapor/solubility calculations and their consistency was confirmed employing the extra-thermodynamic enthalpy-entropy compensation effect. Our experimental data are compatible with reported literature values, and they are typically lower than averaged experimental literature values by about 10%. Critical comparison with other freely available models (modeled vapor/solubility; group and bond additivity methods; Linear Solvation Energy Relationship; SPARC) was performed to validate their applicability to monosulfides and disulfides. Evaluation of theoretical models reveals a large deviation from our measured values by up to four times (in units of M atm⁻¹). Two group contribution models were adjusted in view of the new data, and HLCs for a list of sulfur compounds were calculated. Based on our findings we recommend the evaluation and adaption of theoretical models for monosulfides and disulfides to lower values of solubility and higher values of fugacity.     

Comparison of polycyclic aromatic hydrocarbons and nitropolycyclic aromatic hydrocarbons in airborne particulates collected in downtown and suburban Kanazawa,Japan

In this study, airborne particulates were collected at three sites, two in a downtown area and the other in a suburban area of Kanazawa, Japan in each season for 7 years. Two polycyclic aromatic hydrocarbons (PAHs), pyrene (Py) and benzo[a]pyrene (BaP) and four nitropolycyclic aromatic hydrocarbons (NPAHs), 1-nitropyrene (NP) and 1,3-, 1,6-, and 1,8-dinitropyrenes (DNP) were determined by high-performance liquid chromatography with fluorescence and chemiluminescence detection. At the downtown sites, the mean concentration of each DNP was about two orders of magnitude lower than that of 1-NP and more than three orders of magnitude lower than those of Py and BaP. This tendency reflected the composition of PAHs and NPAHs in diesel-engine exhaust particulates. Concentrations of these PAHs and NPAHs were higher at the downtown sites than at the suburban site, suggesting the dilution of these compounds during the transportation from the downtown to the suburban area. The concentration ratios of NPAHs to PAHs were larger at the downtown sites than at the suburban site. Studies using UV light and sunlight showed that degradation of NPAHs was faster than that of PAHs. Thus, the lower concentrations of NPAHs in the suburban sites may be due to their being photodegraded faster than PAHs during the atmospheric transportation from the downtown area to the suburban area.     

Estimation of PCDD/F distribution and fluxes in the Venice Lagoon,Italy: combining measurement and modelling approaches

The available experimental information on the occurrence of PCDD/Fs in the Venice Lagoon, Italy, was compiled and used to calculate fugacities for the environmental compartments of sediment, suspended particulate matter (SPM), water and air and then used to estimate fugacity ratios and assess the likely net direction of flux between media. The bottom sediment: SPM fugacity ratios for different PCDD/Fs indicate conditions close to equilibrium, suggestive of the close coupling of SPM with re-suspended sediment. Sediment/water and the sediment/air fugacity ratios suggest that net flux directions vary depending on the congener and the location within the lagoon. Net sediment-water-air movement (i.e. re-mobilisation/volatilisation) is suggested for the lighter congeners from the industrial canals, where the highest PCDD/F concentrations in the lagoon occur. The tendency to volatilise increases with decreasing congener molecular weight. In contrast, net deposition (air-water-sediment) appears to be occurring for the heaviest (hepta- and octa-) substituted PCDD/Fs. OCDF represents a marker of the industrial district of the lagoon, decreasing in concentration and as a fraction of total PCDD/Fs with increasing distance. The fugacity-based quantitative water air sediment interaction (QWASI) mass-balance model was applied to the central part of the lagoon. The key parameters for the determination of the model output, identified by a sensitivity analysis, were: the sediment active depth, the sediment re-suspension and deposition rates, and the total input of PCDD/Fs to the system. The QWASI model also indicates the tendency for the lighter PCDD/Fs to be released from surface sediment to the water column.     

A model for prediction of product distributions for the reactions of phenol derivatives with hydroxyl radicals

In this study, with the intention of estimating the photocatalytic or photodegradation rates and finding certain predictors to be used for the determination of the most probable reaction path and the primary intermediate, the reactions of (*)OH radicals with 11 phenol derivatives including benzene were modeled. For 43 possible reaction routes, calculations of the geometric parameters, the electronic and thermodynamic properties of the reactants, the product radicals and the transition state complexes were performed with the semiempirical PM3 and DFT/B3LYP/6-31G(*) methods. The solvation effects were computed using COSMO as the solvation model. Based on the results of quantum mechanical calculations, the rate constants, the branching ratios and the product distributions of all the possible reaction paths were calculated by means of the transition state theory. Three predictors were determined for the prediction of the most probable transition state and the reaction path. The differences in the reaction rates were explained in terms of the presence of hydrogen bonds in the transition state complexes and the entropy effects. Finally the results obtained were compared with the available experimental data in order to assess the reliability of the proposed model.     

城市生活垃圾并流竖炉焚烧模拟实验研究

气化熔融焚烧技术能够避免重金属和二恶英的二次污染，被公认为实现零排放和环境友好型的焚烧方法。在这样的背景下提出了生活垃圾并流竖炉气化熔融焚烧工艺。该工艺以竖炉为气化熔融主体设备，垃圾料层与助燃空气在炉内都是至上而下并流流动，从而使垃圾热解气化产生的可燃气体在竖炉下部完全燃烧，以提供灰渣熔融耗热。并流竖炉热态模拟试验表明，并流时垃圾料层中各点的温度明显高于逆流情况，并流时产生的CO₂量明显高于逆流情况。因此说并流竖炉更适合气化熔融焚烧工艺的要求。     

Partitioning of polychlorinated biphenyls and hexachlorobenzene into human faeces

The dietary absorption of persistent lipophilic organic pollutants (PLOPs) in humans is believed to occur via partitioning of the chemical between the lumen and the wall of the digestive tract. As such, the partitioning properties of the lumen contents are a key factor governing absorption. In this study, the partitioning properties of faeces were measured for 11 polychlorinated biphenyls and hexachlorobenzene (HCB). Four volunteers participated in the study, each of them providing faeces from a normal diet and a vegetarian diet. The faeces/gas equilibrium partition coefficient K(FG) varied by over three orders of magnitude between the different compounds. A linear relationship between log K(FG) and log KOA, the octanol/air partition coefficient, was observed. The slope of the relationship was > 1, indicating that the solvent properties of faeces were less polar than those of octanol. For a given compound, KFG varied up to a factor of 2.8 between the individuals on a normal diet. The influence of the vegetarian diet on K(FG) was negligible for the two volunteers who simply deleted fish and animal products from their normal diet, but K(FG) increased on average by a factor of 2 in the two individuals who increased their consumption of less readily digestible whole grains and vegetables in their vegetarian diet. On the basis of K(FG), the fugacities in the faeces were calculated. They were found to be much lower than the fugacities in blood. It is hypothesised that this is due to a temporary decrease in the fugacity in the wall of the jejunum caused by absorption of dietary lipids that results in equilibration between the lumen contents and the wall of the digestive tract at a fugacity below that present in the blood and the rest of the body.