The modelling of trichloroethene photodegradation in Brij 35 surfactant by two-stage reaction.

Various clean-up technologies have been developed for the removal and/or destruction of trichloroethene (TCE) in the subsurface. Surfactant-aided soil washing followed by photodegradation could be a promising approach to such a task. The modelling of TCE photodegradation by UV in Brij 35 surfactant micelles is therefore investigated. Two stages of TCE degradation are observed in surfactant Brij 35 systems. A lag phase is observed at the commencement of the degradation, but the duration of the lag phase is significantly reduced as the initial pH increases. As the overall decay of TCE is also found to be faster at higher pH levels, it is suggested that the free radical reaction is dominant at high pH levels, and the formation of lag phases is mainly due to the deficiency of free radicals at lower pH levels. Since the period of the lag phase gradually decreases with the increase of initial pH level, and the two pseudo first-order reaction constants (one for the lag phase and one for the subsequent fast decay) for TCE decay in both stages are also pH dependent, a non-steady-state mathematical model is developed for the prediction of TCE photodegradation in Brij 35 solutions, in which the remaining fraction of TCE (C/C0) in the system can be determined at any instant by using a simple parameter of the initial system pH.     

The rate improvement and modeling of trichloroethene photodegradation by acetone sensitizer in surfactant solution

The photodecay of trichloroethene (TCE) in surfactant solution by the help of photosensitizer (acetone, ACE) was investigated and modeled. Apart from the direct photodegradation, photosensitization is presumed to be one of the major mechanisms contributing to overall decay. Quantum yields of TCE photodecay in solution with surfactant Brij 35 and optimal ACE dosage are about 25 times higher than in Brij 35 alone. However, with an excess ACE dosage, ACE will act as a light barrier and attenuate the light intensity available for TCE photodegradation. TCE photodegradation follows a two-stage kinetics, in which a lag phase is followed by a fast decay. Mathematical models were developed for the prediction of the two-stage photodegradation, in which the remaining fraction of TCE (C/C0) in the system becomes predictable.     

Surfactant-enhanced oxidation of trichloroethylene by permanganate--proof of concept

Oxidative dechlorination of chlorinated solvents by permanganate is an emerging technology for remediation of groundwater contaminated with dissolved chlorinated contaminants. In this study, the enhancement of trichloroethylene (TCE) degradation by permanganate in aqueous solution in the presence of surfactant was evaluated through a continuous stir batch reactor system with the presence of permanganate as the limiting reagent and free phase TCE. The TCE degradation was determined by continuous monitoring the amount of chloride produced, which was then reverted to the rate of permanganate consumption. It was found that the chloride production, an indication of TCE degradation, followed a pseudo-first-order reaction kinetics with respect to KMnO(4) in the presence of free phase TCE. When no surfactants were present, the observed pseudo-first-order rate constant (k(obs)) was 0.08-0.19 min(-1) and the half-life (t(1/2)) was 4-9 min for MnO(4)(-). When the surfactant concentration was less than its critical micelle concentration (CMC), the k(obs) values increased to 0.42-0.46 min(-1) and the t(1/2) reduced to 1.5-1.7 min for MnO(4)(-). As the surfactant concentration was greater than the CMC, the k(obs) values increased to 0.56-0.58 min(-1) and the t(1/2) reduced to 1.2-1.3 min. The preliminary results showed that combination of permanganate with a proper type of surfactant can speed up contaminant removal.     

Enhancement of ozone oxidation and its associated processes in the presence of surfactant: degradation of atrazine

In this study, the degradation of atrazine (ATZ) by ozone (O3) oxidation and its associated processes (i.e. UV, UV/O3) in the presence and absence of surfactant was investigated and compared. A non-ionic surfactant, Brij 35, was selected. It was found that the presence of a low concentration of surfactant could improve the removal of ATZ by increasing the dissolution of ozone and the indirect generation of hydroxyl radicals. The saturated ozone level and the reaction rate constants were increased with increasing the concentration of surfactant and then decreased at higher surfactant doses at pH level of 2.5. A similar trend was observed at pH level of 7.0 in the presence of bicarbonate ion, because it is capable of deactivating the hydroxyl radicals generating at higher pH level. However, when the radical reactions become dominant in the ozonation (at pH 7.0 without bicarbonate), the saturated ozone level was higher than that with bicarbonate and the kinetic rate constants were increased first and levelled off with increasing of the dose of surfactant. Through the examining of a proposed unit performance index, the low concentration of surfactant is surely beneficial to the ozonation process. Besides, the direct photolysis and photo-assisted ozonation were compared to the ozonation. A significant enhancement on the decay rate of ATZ was resulted exclusively by adding the surfactant. An enhancement index for quantifying the improvement of the various processes was developed.     

Trichloroethylene degradation by photocatalysis in annular flow and annulus fluidized bed photoreactors

The effects of trichloroethylene (TCE) gas flow rate, relative humidity, TiO(2) film thickness, and UV light intensity on photodegradation of TCE have been determined in an annular flow type photoreactor. Phosgene and dichloroacetyl chloride formation could be controlled as a function of TCE gas flow rate and photodegradation of TCE decreased with increasing relative humidity. The optimum thickness of TiO(2) film was found to be approximately 5 mum and the photocatalytic reaction rate of TCE increased with square root of UV light intensity. In addition, the effects of the initial TCE concentration, phase holdup ratio of gas and solid phases (epsilon(g)/epsilon(s)), CuO loading on the photodegradation of TCE have been determined in an annulus fluidized bed photoreactor. The TCE photodegradation decreased with increasing the initial TCE concentration. The optimum conditions of the phase holdup ratio (epsilon(g)/epsilon(s)) and CuO wt.% for the maximum photodegradation of TCE was found to be 2.1 and 1.1 wt.%, respectively. Therefore, an annulus fluidized bed photoreactor is an effective tool for TCE degradation over TiO(2)/silica gel with efficient utilization of photon energy.     

A micromodel analysis of factors influencing NAPL removal by surfactant foam flooding

A methodology to study the trichloroethylene (TCE) and dodecane removal in porous media by surfactant foams (SF) was presented by using etched-glass micromodels. The purpose of this work was to systematically evaluate the impact of various physicochemical factors such as gas fraction (GF), surfactant concentration, pore structure and nonaqueous phase liquid (NAPL) types on NAPL removal during SF flooding. The TCE displacement by SF was dependent on the gas fraction of SF. Low GFs (50% and 66%) were more efficient for TCE removal and sweep efficiencies than a high GF (85%). An increase in TCE removal was observed with increasing surfactant concentration at a fixed GF. TCE removal by SF flooding appeared to be dependent more to the value of Capillary number rather than to the concentration of surfactant solution. The effect of the pore heterogeneity was evaluated by employing two different types of micromodels. The Capillary number is an important parameter in the determination of sweep efficiency or gas saturation of SF in a nonhomogeneous porous medium. However, the TCE removal from a nonhomogeneous porous medium may not be associated with sweep efficiency. The initial configuration of residual TCE blobs in a nonhomogeneous porous medium would also be influential in displacing TCE. Sweep efficiencies and pressure responses of two NAPL systems (TCE and dodecane) were monitored to evaluate foam stability when the foam contacts the NAPLs. Stable foam contacting with TCE is implied, while it appears that dodecane cause the SF to collapse. All results indicate that the Capillary number (a ratio of viscous forces to capillary forces) is the most important parameter for TCE removal by SF flooding. Micromodel visualizations of water, surfactant and SF floods were showed and also discussed.     

TCE recovery mechanisms using micellar and alcohol solutions: phase diagrams and sand column experiments

Forty-one phase diagrams and fifteen sand column experiments were conducted to evaluate the efficiency of three types of washing solutions to recover trichloroethylene (TCE) at residual saturation and to identify the recovery mechanisms involved. This study demonstrates that: (1) an alcohol and a surfactant combination is more efficient than an alcohol used alone in water; (2) the prediction of the dominant recovery mechanism from the tie line slopes in phase diagram is accurate and can be reproduced in sand column experiments; and (3) TCE recovery efficiency in sand column experiments is generally well represented by the position of the miscibility curve in phase diagrams in the low concentration range. However, the miscibility curve alone is not sufficient to exactly predict the TCE recovery mechanisms involved. Tie line slopes and the critical tie line have to be taken into consideration to select the active matter as well as its concentration and to predict the dominant recovery mechanism in sand column experiments. The sand column experiments quantified the recovery efficiency of each solution and identified the proportion of the recovery mechanisms (mobilisation vs. solubilisation). Washing solutions with an active matter concentration above the critical tie line caused dominating mobilisation. Mobilisation was also dominant when the active matter of the washing solution partitioned into the organic phase and the active matter concentration was below the critical tie line. Solubilisation and emulsification were dominant for washing solutions containing active matter, which principally partitioned into the aqueous phase and an active matter concentration below the critical tie line.     

Quantum yield study of the photodegradation of hydrophobic dyes in the presence of acetone sensitizer.

The photodegradation of hydrophobic disperse dyes with different chromophores in the presence of acetone (ACE) was investigated. In this study, the photodecay of dyes was carried out in the Rayonet RPR-200 merry-go-round photoreactor, with 253.7 nm monochromatic ultraviolet (UV) lamps. A typical azo disperse dye (CI disperse yellow 7--DY7) and an anthraquinone disperse dye (CI disperse orange--DO11) were used as the probe compounds. The results demonstrate that the addition of acetone increases the solubility of hydrophobic disperse dyes and enhances the photosensitization reaction simultaneously. More than ten times of quantum yield enhancement is observed in the presence of ACE photosensitizer than in water alone. The photodegradation of DY7 and DO11 is dominated by photoreduction, which follows pseudo first-order decay, and the rate constants strongly depend on the solvent system (i.e., ACE/H2O ratios) and the initial pH levels. The decay quantum yields of dyes are normally observed with the increase of the ACE/H2O ratio. The optimum quantum yields of DY7 and DO11 were determined at 0.5 (v/v) and 0.25 (v/v), respectively, in alkaline conditions. A further increase in the ACE/H2O ratio reduces the quantum yields, possibly due to light attenuation by excess acetone.     

Solubilization of DNAPLs by mixed surfactant: reduction in partitioning losses of nonionic surfactant

Efforts to remediate the dense nonaqueous phase liquids (DNAPLs) by mobilizing them face with risks of driving the contaminants deeper into aquifer zones. This spurs research for modifying the approach for in situ remediation. In this paper, a novel solubilization of DNAPLs by mixed nonionic and anionic surfactant, Triton X-100 (TX100) and sodium dodecylbenzene sulfonate (SDBS), was presented and compared with those by single ones. Given 1:40 phase ratio of DNAPL:water (v/v) and the total surfactant concentration from 0.2 to 10gl(-1), mixed TX100-SDBS at the total mass ratios of 3:1, 1:1 and 1:3 exhibited significant solubilization for the DNAPLs, trichloroethene (TCE), chlorobenzene (CB) and 1,2-dichlorobenzene (1,2-DCB). The solubilization extent by mixed TX100-SDBS was much larger than by single TX100 and even larger than by single SDBS at the ratios of 1:1 and 1:3, respectively. TX100 partitioning into the organic phase dictated the solubilization extent. The TX100 losses into TCE, CB and 1,2-DCB phases were more than 99%, 97% and 97% when single TX100 was used. With SDBS alone, no SDBS partitioned into DNAPLs was observed and in mixed systems, SDBS decreased greatly the partition loss of TX100 into DNAPLs. The extent of TX100 partition decreased with increasing the amount of SDBS. The mechanism for reduction of TX100 partition was discussed. TX100 and SDBS formed mixed micelles in the solution phase. The inability of SDBS to partition into DNAPLs and the mutual affinity of SDBS and TX100 in the mixed micelle controlled the partitioning of TX100 into DNAPL phase. The work presented here demonstrates that mixed nonionic-anionic surfactants would be preferred over single surfactants for solubilization remediation of DNAPLs, which could avoid risks of driving the contaminants deeper into aquifers and decrease the surfactant loss and remediation cost.     

Competitive sorption of cis-DCE and TCE in silica gel as a model porous mineral solid

The competitive sorption of 1,2-cis-dichloroethene (cis-DCE) and trichloroethene (TCE) was investigated by means of column experiments using a model porous mineral solid represented by silica gel. The experimental isotherms were obtained by employing a chromatographic method. The competitive sorption isotherms were modelled with the extended Freundlich and extended Langmuir isotherms, using the parameters from single-solute experiments. The breakthrough curves were modelled with the advection-dispersion transport equation coupled with the lumped pore diffusion model. The best results were obtained when the extended Freundlich isotherm was employed. The competitive sorption was revealed with the presence of an overshoot in the breakthrough curve of cis-DCE and a decrease in the degree of sorption of cis-DCE (20%) and TCE (12%). A linear dependency of the overshoot with an increase in the concentration of cis-DCE at a fixed concentration of TCE was observed, between 16% and 20%, and at least at concentrations <6 mg L(-1) in the liquid phase. The displaced molecules of cis-DCE by TCE were accumulated through the column causing its overshoot; thus short columns may hinder its observation. Thermodynamic analysis shows an exothermic adsorption process of -34 to -41 kJ mol(-1), which is enhanced by sorption in micropores. The Gibbs free energy is positive for cis-DCE in the multi-component case, due to its displacement by TCE.     

Modeling the quantum yields of herbicide 2,4-D decay in UV/H2O2 process

The photodecay of herbicide 2,4-D in a hydrogen peroxide-aided photolysis process was studied and modeled. The decay rate of 2,4-D was known to be low in the natural environment, but rate improvement was achieved in an H2O2/UV system. The 2,4-D decay quantum yields under ultraviolet (UV) light at 253.7 nm increased from 4.86 x 10(-6) to 1.30 x 10(-4) as the ratio of [H2O2]/[2,4-D] increased from 0.05 to 12.5. Apparently, in the presence of UV light, the decay rate of 2,4-D could be greatly improved as the concentration of hydrogen peroxide increased. However, the efficiency of 2,4-D photodecay was retarded if the concentration of H2O2 was overdosed, because the excess hydrogen peroxide consumes the hydroxyl radicals (HO*) in the solution, resulting in a much weaker oxidant HO2*. The decay of 2,4-D was also pH dependent. A ranking of acid (highest), base (middle) and neutral (lowest) was observed owing to the property change of reactants and the shifting of dominant mechanisms among photolysis, photohydrolysis and chemical oxidation. Two mathematical models were proposed to predict the quantum yield for various [H2O2]/[2,4-D] ratios and initial pH levels, in which very good correlation was found for the ranges of regular application.     

Degradation of trichloroethylene by photocatalysis in an internally circulating slurry bubble column reactor

The effects of initial trichloroethylene (TCE) concentration, recirculating liquid flow rate and gas velocity on photodegradation of TCE have been determined in an internally circulating slurry bubble column reactor (0.15m-ID x 0.85 m-high). Titanium dioxide (TiO2) powder was employed as a photocatalyst and the optimum loading of TiO2 in the present system is found to be approximately 0.2 wt%. The stripping fraction of TCE by air flow increases but photodegradation fraction of TCE decreases with increasing the initial TCE concentration, recirculating liquid flow rate and gas velocity. The average removal efficiency of TCE is found to be approximately 97% in an internally circulating slurry bubble column reactor.     

Visualization of TCE recovery mechanisms using surfactant-polymer solutions in a two-dimensional heterogeneous sand model

This research focused on the optimization of TCE dissolution in a physical two-dimensional model providing a realistic representation of a heterogeneous granular aquifer. TCE was infiltrated in the sand pack where it resided both in pools and in zones of residual saturation. Surfactant was initially injected at low concentration to minimize TCE remobilization at first contact but was incrementally increased later during the experiment. Xanthan gum was added to the injected surfactant solution to optimize the sweep efficiency through the heterogeneous medium. Photographs and digital image analysis illustrated the interactions between TCE and the injected fluids. During the polymer flood, the effects of heterogeneities inside the sand pack were greatly reduced by the increased fluid viscosity and the shear-thinning effects of the polymer. The polymer also improved the contact between the TCE ganglia and the surfactant-polymer solution, thereby promoting dissolution. Surfactants interacted with the polymer reducing the overall viscosity of the solution. At first contact with a 0.5%(mass) surfactant solution, the TCE pools drained and some remobilization occurred. However, no TCE bank was formed and TCE did not penetrate into any previously uncontaminated areas. As a result, TCE surface area was increased. Subsequent surfactant floods at higher surfactant concentrations did not trigger more remobilization. TCE was mainly dissolved by the solution with the highest surfactant concentration. Plugging from bacterial growth or microgel formation associated to the polymer at the inflow screen prevented the full completion of the experiment. However, more than 90% of TCE was recovered with the circulation of less than 6 pore volumes of surfactant-polymer solution.     

Cometabolic degradation kinetics of TCE and phenol by Pseudomonas putida

Modeling of cometabolic kinetics is important for better understanding of degradation reaction and in situ application of bio-remediation. In this study, a model incorporated cell growth and decay, loss of transformation activity, competitive inhibition between growth substrate and non-growth substrate and self-inhibition of non-growth substrate was proposed to simulate the degradation kinetics of phenol and trichloroethylene (TCE) by Pseudomonas putida. All the intrinsic parameters employed in this study were measured independently, and were then used for predicting the batch experimental data. The model predictions conformed well to the observed data at different phenol and TCE concentrations. At low TCE concentrations (<2 mg l(-1)), the models with or without self-inhibition of non-growth substrate both simulated the experimental data well. However, at higher TCE concentrations (>6 mg l(-1)), only the model considering self-inhibition can describe the experimental data, suggesting that a self-inhibition of TCE was present in the system. The proposed model was also employed in predicting the experimental data conducted in a repeated batch reactor, and good agreements were observed between model predictions and experimental data. The results also indicated that the biomass loss in the degradation of TCE below 2 mg l(-1) can be totally recovered in the absence of TCE for the next cycle, and it could be used for the next batch experiment for the degradation of phenol and TCE. However, for higher concentration of TCE (>6 mg l(-1)), the recovery of biomass may not be as good as that at lower TCE concentrations.     

Natural attenuation of chlorinated ethene compounds: model development and field-scale application at the Dover site

A multi-dimensional and multi-species reactive transport model was developed to aid in the analysis of natural attenuation design at chlorinated solvent sites. The model can simulate several simultaneously occurring attenuation processes including aerobic and anaerobic biological degradation processes. The developed model was applied to analyze field-scale transport and biodegradation processes occurring at the Area-6 site in Dover Air Force Base, Delaware. The model was calibrated to field data collected at this site. The calibrated model reproduced the general groundwater flow patterns, and also, it successfully recreated the observed distribution of tetrachloroethene (PCE), trichloroethene (TCE), dichloroethylene (DCE), vinyl chloride (VC) and chloride plumes. Field-scale decay rates of these contaminant plumes were also estimated. The decay rates are within the range of values that were previously estimated based on lab-scale microcosm and field-scale transect analyses. Model simulation results indicated that the anaerobic degradation rate of TCE, source loading rate, and groundwater transport rate are the important model parameters. Sensitivity analysis of the model indicated that the shape and extent of the predicted TCE plume is most sensitive to transmissivity values. The total mass of the predicted TCE plume is most sensitive to TCE anaerobic degradation rates. The numerical model developed in this study is a useful engineering tool for integrating field-scale natural attenuation data within a rational modeling framework. The model results can be used for quantifying the relative importance of various simultaneously occurring natural attenuation processes.     

Comparison of PCE and TCE disappearance in heated volatile organic analysis vials and flame-sealed ampules

The rates of hydrolysis reported for tetrachloroethylene (PCE) and trichloroethylene (TCE) at elevated temperatures range over two orders-of-magnitude, where some of the variability may be due to the presence of a gas phase. Recent studies suggest that volatile organic analysis (VOA) vials provide a low-cost and readily available zero headspace system for measuring aqueous-phase hydrolysis rates. This work involved measuring rates of PCE and TCE disappearance and the corresponding appearance of dechlorination products in water-filled VOA vials and flame-sealed ampules incubated at 21 and 55 °C for up to 95.5 days. While PCE and TCE concentrations readily decreased in the VOA vials to yield first-order half lives of 11.2 days for PCE and 21.1 days for TCE at 55 °C, concentrations of anticipated dechlorination products, including chloride, remained constant or were not detected. The rate of PCE disappearance was 34 times faster in VOA vials at 55 °C compared to values obtained with flame-sealed ampules containing PCE-contaminated water. In addition, the concentration of TCE increased slightly in flame-sealed ampules incubated at 55 °C, while a decrease in TCE levels was observed in the VOA vials. The observed losses of PCE and TCE in the VOA vials were attributed to diffusion and sorption in the septa, rather than to dechlorination. These findings demonstrate that VOA vials are not suitable for measuring rates of volatile organic compound hydrolysis at elevated temperatures.     

Influence of pH on persulfate oxidation of TCE at ambient temperatures

In situ chemical oxidation (ISCO) is a technology used for groundwater remediation. This laboratory study investigated the use of the oxidant sodium persulfate for the chemical oxidation of trichloroethylene (TCE) at near ambient temperatures (10, 20 and 30 degrees C) to determine the influence of pH (pH=4, 7 and 9) on the reaction rate (i.e., pseudo-first-order rate constants) over the range of temperatures utilized. TCE solutions (60 mg l(-1); 0.46 mM) were prepared in phosphate buffered RO water and a fixed persulfate/TCE molar ratio of 50/1 was employed in all tests. Half-lives of TCE degradation at 10, 20 and 30 degrees C (pH 7) were 115.5, 35.0 and 5.5h, respectively. Maximum TCE degradation occurred at pH 7. Lowering system pH resulted in a greater decrease in TCE degradation rates than increasing system pH. Radical scavenging tests used to identify predominant radical species suggested that the sulfate radical (SO(4)(.-)) predominates under acidic conditions and the hydroxyl radical (.OH) predominates under basic conditions. In a side by side comparison of TCE degradation in a groundwater vs. unbuffered RO water it was demonstrated that when the system pH is buffered to near neutral pH conditions due to the presence of natural occurring groundwater constituents that the TCE degradation rate is higher than in unbuffered RO water where the system pH dropped from 5.9 to 2.8. The results of this study suggest that in a field application of ISCO, pH should be monitored and adjusted to near neutral if necessary.     

Partitioning of hydrogen peroxide between the gas and liquid phases in the presence of surfactant

Gas-liquid phase partitioning is a key physical property that can predict the environmental fate of a compound between two phases. Several environmental factors have been known to affect the gas-liquid phase partitioning. We investigated the influence of surfactant on the gas-liquid phase partitioning of hydrogen peroxide (H(2)O(2)). The surfactant used was ammonium perfluorooctanoate (APFO). H(2)O(2) solution containing the surfactant was equilibrated in a closed system and gas phase H(2)O(2) concentration was measured by the peroxyoxalate chemiluminescence (PO-CL) method. Gas phase H(2)O(2) concentrations remained constant below the critical micelle concentration (CMC) and increased linearly with surfactant concentration above the CMC, which indicated that surfactant micelles influenced the gas-liquid phase partitioning of H(2)O(2). This result showed that H(2)O(2)-micelle interactions are less favorable than H(2)O(2)-H(2)O interactions. Surfactant monomers did not affect the gas-liquid phase partitioning of H(2)O(2) due to the absence of micelles. Solvent (methanol) effect was also investigated and showed that gas phase H(2)O(2) concentrations increased with the addition of solvent. This indicated the unfavorable interaction of H(2)O(2) with hydrophobic medium compared to hydrophilic one. It is consistent with the result that H(2)O(2)-micelles has a weaker interaction than H(2)O(2)-water because surfactant micelles are hydrocarbon-like organic phase rather than aqueous phase.     

Photocatalytic oxidation of monuron in the suspension of WO3 under the irradiation of UV-visible light

A comprehensive study of the degradation of monuron, one of the phenylurea herbicides, was conducted by UV-Vis/WO₃ process. It was found that hydroxyl radicals played a major role in the decay of monuron while other radicals (e.g. superoxide) and hole might also contribute to the decomposition of monuron. The oxidation path likely plays a major role in the generation of hydroxyl radicals. The effects of initial pH level, initial concentration of monuron, and inorganic oxidants on the performance of UV-Vis/WO₃ process were also investigated and optimized. Comparison between monuron decay pathways by UV-Vis/WO₃ and UV/TiO₂ was conducted. The decay mechanisms, including N-terminus demethylation, dechlorination and direct hydroxylation on benzene ring, were observed to be involved in the oxidation of monuron in these two processes. Sixteen intermediates were identified during the photodegradation of monuron and degradation pathways were proposed accordingly.     

Use of statistical tools to evaluate the reductive dechlorination of high levels of TCE in microcosm studies

A large, multi-laboratory microcosm study was performed to select amendments for supporting reductive dechlorination of high levels of trichloroethylene (TCE) found at an industrial site in the United Kingdom (UK) containing dense non-aqueous phase liquid (DNAPL) TCE. The study was designed as a fractional factorial experiment involving 177 bottles distributed between four industrial laboratories and was used to assess the impact of six electron donors, bioaugmentation, addition of supplemental nutrients, and two TCE levels (0.57 and 1.90 mM or 75 and 250 mg/L in the aqueous phase) on TCE dechlorination. Performance was assessed based on the concentration changes of TCE and reductive dechlorination degradation products. The chemical data was evaluated using analysis of variance (ANOVA) and survival analysis techniques to determine both main effects and important interactions for all the experimental variables during the 203-day study. The statistically based design and analysis provided powerful tools that aided decision-making for field application of this technology. The analysis showed that emulsified vegetable oil (EVO), lactate, and methanol were the most effective electron donors, promoting rapid and complete dechlorination of TCE to ethene. Bioaugmentation and nutrient addition also had a statistically significant positive impact on TCE dechlorination. In addition, the microbial community was measured using phospholipid fatty acid analysis (PLFA) for quantification of total biomass and characterization of the community structure and quantitative polymerase chain reaction (qPCR) for enumeration of Dehalococcoides organisms (Dhc) and the vinyl chloride reductase (vcrA) gene. The highest increase in levels of total biomass and Dhc was observed in the EVO microcosms, which correlated well with the dechlorination results.