Triton X-100在土壤颗粒上的吸附特征研究

采用平衡振荡法，研究了砂土对非离子表面活性剂Triton X-100的吸附特征。结果表明，砂颗粒对Triton X-100的吸附能力总体较低，单位吸附含量均＜1.1 mg/g；砂颗粒吸附Triton X-100过程中存在显著的吸附剂浓度效应，砂颗粒上Triton X-100含量随着固液比（吸附剂浓度）的增大而减小；吸附容量q_m与平衡常数K_L值随固液比变化而变化，Langmuir方程适用范围是起始浓度C₀相对较小的固液吸附体系；0.5～1 mm石英砂的吸附能力略＞0.2～0.5 mm石英砂，0.5～1 mm和0.2～0.5 mm石英砂吸附Triton X-100变化特征具有显著的一致性，采用高斯拟合模型可以反映出石英砂吸附Triton X-100的变化规律，相关系数R²均＞0.98。     

Degradation of carbon tetrachloride by iron metal: Complexation effects on the oxide surface

Dehalogenation of chlorinated aliphatic contaminants at the surface of zero-valent iron metal (Fe⁰) is mediated by the thin film of iron (hydr)oxides found on Fe⁰ under environmental conditions. To evaluate the role this oxide film plays in the reduction of chlorinated methanes, carbon tetrachloride (CCl₄) degradation by Fe⁰ was studied under the influence of various anions, ligands, and initial CCl₄ concentrations ([P]_o). Over the range of conditions examined in these batch experiments, the reaction kinetics could be characterized by surface-area-normalized rate constants that were pseudo-first order for CCl₄ disappearance (k_CCl4), and zero order for the appearance of dissolved Fe²⁺ (k_Fe²⁺). The rate of dechlorination exhibits saturation kinetics with respect to [P]_o, suggesting that CCl₄ is transformed at a limited number of reactive surface sites. Because oxidation of Fe⁰ by CCl₄ is the major corrosion reaction in these systems, k_Fe²⁺ also approaches a limiting value at high CCl₄ concentrations. The adsorption of borate strongly inhibited reduction of CCl₄, but a concomitant addition of chloride partially offset this effect by destabilizing the film. Redox active ligands (catechol and ascorbate), and those that are not redox active (EDTA and acetate), all decreased k_CCl4 (and k_Fe²⁺). Thus, it appears that the relatively strong complexation of these ligands at the oxide–electrolyte interface blocks the sites where weak interactions with the metal oxide lead to dehalogenation of chlorinated aliphatic compounds.     

Effect of surfactant alkyl chain length on soil cadmium desorption using surfactant/ligand systems

The effect of surfactant alkyl chain length on soil Cd desorption was studied using nonionic surfactants of polyethylene oxide (PEO) of PEO chain lengths of 7.5 (Triton X-114), 9.5 (Triton X-100), 30 (Triton X-305), or 40 units (Triton X-405) in combination with the I- ligand. Triplicate 1 g soil samples were equilibrated with 15 ml of surfactant-ligand mixture, at concentrations of 0.025, 0.50 or 0.10, and 0.0, 0.168 or 0.336 mol/l, respectively. After shaking the samples for 24 h, the supernatant fraction was analyzed for Cd content to determine the percent of Cd desorbed from the soil. After five successive washings, 53%, 40% and 25% of Cd had been desorbed by 0.025, 0.050 or 0.10 mol/l of Triton X-114, respectively, in the presence of 0.336 mol/l of I-, whereas with the same conditions, Triton X-100 desorbed 61%, 57% and 56% Cd and either Triton X-305 or Triton X-405 desorbed 51, 40 and 14 to 16% Cd. The most efficient Cd desorption was obtained using 0.025 mol/l Triton X-100 in admixture with 0.336 mol/l I-. Increased surfactant concentration was detrimental to Cd desorption consistent with a process that blocked ligand access to the soil particle surface. After 5 washings,the cumulative cadmium desorption decreased with increasing surfactant alkyl chain length, indicating that the metal-ligand complexes are preferably stabilized by the micelles' hydrophobic octyl phenyl (OP) group rather than by the hydrophilic PEO group. In the absence of ligand, the surfactants alone desorbed less than 1% Cd from the contaminated soil, suggesting that the ligand, rather than the surfactant, extracts the metal, to be subsequently stabilized within the surfactant micelles.     

Selective adsorption of phenanthrene dissolved in surfactant solution using activated carbon

Selective adsorption of a hazardous hydrophobic organic compound (HOC) by activated carbon as a means of recovering surfactants after a soil washing process was investigated. As a model system, phenanthrene was selected as a representative HOC and Triton X-100 as a nonionic surfactant. Three activated carbons that differed in size (Darco 20–40 (D20), 12–20 (D12) and 4–12 (D4) mesh sizes) were used in adsorption experiments. Adsorption of surfactant onto activated carbon showed a constant maximum above the critical micelle concentration, which were 0.30, 0.23, 0.15 g g⁻¹ for D20, D12, and D4, respectively. Selectivity for phenanthrene to Triton X-100 was much higher than 1 over a wide range of activated carbon doses (0–6 g l⁻¹) and initial phenanthrene concentrations (10–110 mg l⁻¹). Selectivity generally increased with decreasing particle size, increasing activated carbon dose, and decreasing initial concentration of phenanthrene. The highest selectivity was 74.9, 57.3, and 38.3 for D20, D12, and D4, respectively, at the initial conditions of 10 mg l⁻¹ phenanthrene, 5 g l⁻¹ Triton X-100 and 1 g l⁻¹ activated carbon. In the case of D20 at the same conditions, 86.5% of the initial phenanthrene was removed by sorption and 93.6% of the initial Triton X-100 remained in the solution following the selective adsorption process. The results suggest that the selective adsorption by activated carbon is a good alternative for surfactant recovery in a soil washing process.     

DDT uptake by arbuscular mycorrhizal alfalfa and depletion in soil as influenced by soil application of a non-ionic surfactant

A greenhouse pot experiment was conducted to investigate the colonization of alfalfa roots by the arbuscular mycorrhizal (AM) fungus Glomus etunicatum and application of the non-ionic surfactant Triton X-100 on DDT uptake by alfalfa and depletion in soil. Mycorrhizal colonization led to an increase in the accumulation of DDT in roots but a decrease in shoots. The combination of AM inoculation and Triton X-100 application enhanced DDT uptake by both the roots and shoots. Application of Triton X-100 gave much lower residual concentrations of DDT in the bulk soil than in the rhizosphere soil or in the bulk soil without Triton X-100. AM colonization significantly increased bacterial and fungal counts and dehydrogenase activity in the rhizosphere soil. The combined AM inoculation of plants and soil application of surfactant may have potential as a biotechnological approach for the decontamination of soil polluted with DDT.     

蓖麻油衍生微乳液对菲的增溶和洗脱作用及其对菲污染土壤的修复机理

比较研究了蓖麻油硫酸盐(SCOS)与普通表面活性剂Triton X-100(TX100)、Tween 80(TW80)、Brij35、十二烷基苯磺酸钠(SDBS)和十二烷基硫酸钠(SDS)等对菲的增溶和洗脱作用.结果表明,菲表观溶解度与SCOS的浓度呈单一线性关系,SCOS微乳液对菲的增溶比SR=0.0314为最大,菲在微乳相和水相之间的分配系数logKem=4.44,大于菲在胶束相和水相之间的分配系数(logKmc).1:10土-水体系下,SCOS微乳液对菲污染土壤的清洗速率最快,清洗效率最高.SCOS有望成为土壤有机污染淋洗修复的增效试剂.     

Microbial reductive dechlorination of polychlorinated biphenyls in heat treated and bromoethanesulfonate treated anaerobic sediment slurries

Anaerobic reductive dechlorination of polychlorinated biphenyls (PCBs) in heat treated, bromoethanesulfonate (BES) treated, and untreated slurries of PCB-contaminated upper Hudson River sediment was investigated to better understand the microorganisms that mediate this process. Extensive meta-and para-dechlorination of Aroclor 1242 and 2,3,4-trichlorobiphenyl (2,3,4-CB) occurred in both the untreated and heat treated slurries. Heat treatment of the slurries eliminated methanogenesis, enhanced 2,3,4-CB dechlorination, and caused extensive meta- and para-dechlorination of Aroclor 1242 earlier than in untreated slurries. BES treatment (1 mM) of the slurries caused a 90% reduction in methanogenesis and inhibited metadechlorination of PCB congeners containing 2,3- and 2,5-dichlorophenyl groups. The results suggest that there are at least two distinct microbial PCB reductive dechlorination activities in PCB-contaminated upper Hudson River sediment, a meta-dechlorination activity and a para-dechlorination activity on Aroclor 1242. Both of these microbial activities are apparently not methanogenic and are resistant to or activated by heat treatment. In addition, the meta- but not the para-dechlorinating activity is inhibited by BES treatment.     

The influence of defoamer on removal of PAHs in soil washing

The use of surfactants during soil washing process can create massive foam, which has a negative impact on the effective use of equipment. A series of tests was conducted to evaluate the defoaming performance of three defoamers and to investigate the influence on removal of polycyclic aromatic hydrocarbons (PAHs) during enhanced soil washing by the addition of the defoamer. Results showed that polydimethylsiloxane oil, which is the most common biomaterial used in commercial antifoaming and defoaming agents, has the best defoaming performance. With the addition of 0.1% polydimethylsiloxane oil, the removal ratios of total 16 PAHs (ΣPAHs) increased up to 53.48% and 75.92% when washing time was 5 min and 30 min, respectively, compared with the removal ratios of 44.12% and 67.28% with Triton X-100 solution only. This indicated that the proper selection of defoamer not only solves massive foaming problem but also brings out a positive influence on PAH removal during the soil washing process.

Implications: Three kinds of defoamers (kieselguhr, dodecanol, and polydimethylsiloxane oil) were collected to destroy the foam produced by Triton X-100. Among those defoamers, the polydimethylsiloxane (PDMS) oil has the best defoaming performances. The surface tension of the Triton X-100 solution with the addition of PDMS was lower. The addition of PDMS could improve the removal ratio of ΣPAHs during soil washing. That may be attributed to the addition of the nonionic surfactant Tergitol NP-10 as the emulsifier in the defoamer. After all, the results do not provide any indication of the influence on the solubilization micelles. It is thus questionable whether other components of PDMS oil could improve the PAH solubilization.     

Abiotic reductive dechlorination of chlorinated ethylenes by soil

Abiotic reductive dechlorination of chlorinated ethylenes by soil in anaerobic environments was characterized to improve knowledge of the behavior of chlorinated ethylenes in natural systems, including systems modified to promote attenuation of contaminants. Target organics in the soil suspension reached sorption equilibrium in 2 days and the sorption isotherm of target organics was properly described by the linear sorption model. A modified Langmuir-Hinshelwood model was developed to describe the kinetics of reductive dechlorination of target organics by soil. The rate constants for the reductive dechlorination of chlorinated ethylenes at the reactive surfaces of reduced soils were found in the range between 0.055 (+/- 8.9%) and 2.60 (+/- 3.2%) day(-1). The main transformation products in reduced soil suspensions were C2 hydrocarbons. No chlorinated intermediates were observed at concentrations above detection limits. Five cycles of reduction of the soil followed by oxidation of the soil with trichloroethylene (TCE) did not affect the removal of TCE. The removal was affected by the reductants used and increased in the order: Fe(II) < dithionite < Fe(II) + dithionite.     

A comparative study of adsorption of an anionic and a non-ionic surfactant by soils based on physicochemical and mineralogical properties of soils

In the present work we performed a comparative study on the adsorption of the surfactants sodium dodecyl sulphate (SDS) (anionic), and octylphenoxypolyethoxyethanol (Triton X-100) (non-ionic) to 18 soils with organic matter (OM) and clay fraction contents varying over a broad range. The objective of the study was to gain further insight into the influence of the physicochemical and mineralogical properties of soils on the adsorption of surfactants by soils. Adsorption isotherms were obtained using concentrations below the critical micellar concentration (cmc) of the surfactants. The adsorption coefficients, Kf, determined from the Freundlich equation were lower for SDS (range 1.77-82.1, mean value 36.3) than for Triton X-100 (range 0.01-913, mean value 257). Simple and multiple correlation coefficients were obtained between Kf values and soil characteristics. The results obtained indicate the influence of the OM content on the adsorption of SDS (r=0.64, p<0.01) and of the clay fraction content on that of Triton X-100 (r=0.83, p<0.001). Additionally, we observed a preferential adsorption of SDS by the 1:1 mineral kaolinite (r=0.54, p<0.05), while Triton X-100 was adsorbed mainly by the 2:1 minerals, montmorillonite (r=0.66, p<0.01) and illite (r=0.87, p<0.001). According to the influence of different soil parameters on adsorption, different mechanisms of adsorption are proposed for each surfactant. Our findings point to the interest of considering the physicochemical properties of soils and also the mineralogy of the soil clay fraction when selecting a surfactant in technologies involving enhanced solubilization and removal of contaminants from soils and sediments.     

The reductive degradation of 1,1,1-trichloroethane by Fe(0) in a soil slurry system

Most studies on the treatment of chlorinated contaminants by Fe(0) focus on aqueous system tests. However, few is known about the effectiveness of these tests for degrading chlorinated contaminants such as 1,1,1-trichloroethane (TCA) in soil. In this work, the reductive degradation performance of 1,1,1-TCA by Fe(0) was thoroughly investigated in a soil slurry system. The effects of various factors including acid-washed iron, the initial 1,1,1-TCA concentration, Fe(0) dosage, slurry pH, and common constituents in groundwater and soil such as Cl^?, HCO₃ ^?, SO₄ ^2?, and NO₃ ^? anions and humic acid (HA) were evaluated. The experimental results showed that 1,1,1-TCA could be effectively degraded in 12 h for an initial Fe(0) dosage of 10 g L^?1 and a soil/water mass ratio of 1:5. The soil slurry experiments showed two-stage degradation kinetics: a slow reaction in the first stage and a fast reductive degradation of 1,1,1-TCA in the second stage. The reductive degradation of 1,1,1-TCA was expedited as the mass concentration of Fe(0) increased. In addition, high pHs adversely affected the degradation of 1,1,1-TCA over a pH range of 5.4–8.0 and the reductive degradation efficiency decreased with increasing slurry pH. The initial 1,1,1-TCA concentration and the presence of Cl^? and SO₄ ^2? anions had negligible effects. HCO₃ ^? anions had a accelerative effect on 1,1,1-TCA removal, and both NO₃ ^? and HA had inhibitory effects. A Cl^? mass balance showed that the amount of Cl^? ions released into the soil slurry system during the 1,1,1-TCA degradation increased with increasing reaction time, suggesting that the main degradation mechanism of 1,1,1-TCA by Fe(0) in a soil slurry system was reductive dechlorination with 1,1-DCA as the main intermediate. In conclusion, this study provides a theoretical basis for the practical application of the remediation of contaminated sites containing chlorinated solvent.     

Reductive dechlorination for remediation of polychlorinated biphenyls

Technologies such as thermal, oxidative, reductive, and microbial methods for the remediation of polychlorinated biphenyls (PCBs) have previously been reviewed. Based on energy consumption, formation of PCDD/F, and remediation efficiency, reductive methods have emerged as being advantageous for remediation of PCBs. However, many new developments in this field have not been systematically reviewed. Therefore, reductive technologies published in the last decade related to remediation of PCBs will be reviewed here. Three categories, including catalytic hydrodechlorination with H₂, Fe-based reductive dechlorination, and other reductive dechlorination methods (e.g., hydrogen-transfer dechlorination, base-catalyzed dechlorination, and sodium dispersion) are specifically reviewed. In addition, the advantages of each remediation technology are discussed. In this review, 108 articles are referenced.     

Reductive dechlorination of polychlorinated dibenzo-p-dioxins by zerovalent iron in subcritical water

A new method for reductive dechlorination of polychlorinated dibenzo-p-dioxins (PCDDs) and remediation of contaminated soils is described that uses zerovalent iron as the dechlorination agent and subcritical water as reaction medium and extractive solvent. It is found that the zerovalent iron can be applied for stepwise dechlorination of octachlorinated dibenzo-p-dioxin (OCDD) on various matrixes in subcritical water. By using iron powder as matrix higher chlorinated congeners were practically completely reduced to less than tetra-substituted homologues. A significant part of residual OCDD, when it was spiked in to soils, and formed less chlorinated congeners are extracted with water in the given conditions. The solubility of OCDD was increased by a 4–6 orders over its solubility at ambient conditions. The new method of contentious-flow extraction is described.     

Aged and bound herbicide residues in soil and their bioavailability part 2: Uptake of aged and non‐extractable (bound) [carbonyl‐14C] methabenzthiazuron residues by maize

Abstract

[Carbonyl‐ C]methabenzthiazuron (MBT) was applied to growing winter wheat in an outdoor lysimeter. The amount applied corresponded to 4 kg Tribunil/ha. 140 days after application the 0–2,5 cm soil layer was removed from the lysimeter. This soil contained about 40 % of the applied radioactivity. Using 0,01 M CaCl₂ solution or organic solvents, the extractable residues were removed from the soil. The bioavailability of the non‐extractable as well as aged residues remaining in the soil was investigated in standardized microecosystems containing 1.5 kg of dry soil. During a 4 weeks period the total uptake (4 maize plants/pot) amounted up to 3,6; 2,2; and 0,9 % of the radioactivity from soils containing aged MBT residues, MBT residues non‐extractable‐with 0,01 MCaCl₂ or MBT residues non‐extractable with organic solvents, respectively. About 20 % of the radioactivity found in maize leaves represented chromatographically characterized parent compound. At the end of the plant experiment the soil was extracted again with 0,01 M CaCl₂ and with organic solvents. The soil extracts and also the organic phases obtained from the aqueous fulvic acid solution contained unchanged parent compound.     

Ni/Fe/Al2O3·PVDF催化还原剂的表征及制备过程优化

在PVDF基体改性的基础上,采用浸渍法制备出Ni/Fe/Al₂O₃·PVDF催化还原剂。通过对一氯乙酸的脱氯效果研究,对交联液配比及交联时间、不同浓度硫酸镍浸渍时间、镍铁比等因素进行优化,实验优化结果表明,Ni/Fe/Al₂O₃·PVDF催化还原剂对一氯乙酸脱氯60 min脱氯率达到64%。经SEM表征,制备出的双金属在膜载体表面及断面分布均匀,呈球状和片状结构且双金属未发生团聚。     

Enhancing p-cresol extraction from soil

Soil washing is a potential technology for rapid removal of organic hydrocarbons sorbed to soils. In this work, p-cresol desorption with different non-ionic surfactants (Tween 80, Brij 30 and Triton X-100) was compared to cyclodextrine and citrate as solubilizer. A series of batch extraction experiments were conducted at 20 °C using the field soil with different extracting solutions at various concentrations to investigate the removal efficiency and to optimize the concentration of the extractant. The use of the different extracting agents was very selective to p-cresol extraction, minimizing soil organic matter releasing and maintaining the natural pH of the soil. The highest asymptotic values of desorption percentages were obtained for Tween 80 and Brij 30 at 48 h. However, Brij 30 ecotoxicity (EC₅₀ = 0.5 mg L⁻¹) is in the same order of that obtained for p-cresol, being this surfactant clearly ruled out. Liquid to solid ratio of 2.5 mL g⁻¹ presented the best extraction results, while concentrations higher than 1 g L⁻¹ for Tween 80 and Citrate did not produce any significant effect on the desorption efficiency. p-Cresol extraction efficiencies higher than 70% and 60% for Tween 80 and Citrate, respectively.     

Degradation of pentachlorobiphenyl by a sequential treatment using Pd coated iron and an aerobic bacterium (H1)

The reductive dechlorination and biodegradation of 2,2^′4,5,5^′-pentachlorobiphenyl (PCB#101) was investigated in a laboratory-scale. Palladium coated iron (Pd/Fe) was used as a catalytic reductant for the chemical degradation of 2,2^′4,5,5^′-pentachlorobiphenyl, and an aerobic bacteria was used for biodegradation following the chemical reaction in this study. Dechlorination was affected by several factors such as Pd loading, initial soil pH and the amount of Pd/Fe used. The results showed that higher Pd loading, higher dosage of Pd/Fe and slightly acid condition were beneficial to the catalytic dechlorination of 2,2^′,4,5,5^′-pentachlorobiphenyl. In laboratory batch experiments, 2,2^′4,5,5^′-pentachlorobiphenyl was reduced in the presence of Pd/Fe bimetal, which was not further degraded by aerobic bacteria. 2,2^′,4-trichlorobiphenyl (PCB#17), a reduction product from 2,2^′4,5,5^′-pentachlorobiphenyl, was readily biodegraded in the presence of a aerobic bacterial strain. It is suggested that an integrated Pd/Fe catalytic reduction-aerobic biodegradation process may be a feasible option for treating PCB-contaminated soil.     

Distribution of polycyclic aromatic hydrocarbons in soil-water system containing a nonionic surfactant

The effect of a nonionic surfactant, Triton X-100 (TX100), on the distribution of four representative polycyclic aromatic hydrocarbons (PAHs), phenanthrene, fluorene, acenaphthene and naphthalene, in soil-water system was studied on a natural soil. The apparent soil-water distribution coefficient with surfactant (Kd*) for these compounds increased when TX100 equilibrium concentration from zero to around the critical micelle concentration (CMC), followed by a decrease in Kd* at TX100 equilibrium concentration greater than CMC. This is a direct result of surfactant sorption onto soil followed by PAHs partitioning to the sorbed surfactant. The values of carbon-normalized solute distribution coefficient (Kss) with the sorbed TX100 are greater than the corresponding partition coefficients with soil organic matter (Koc), which indicates the soil-sorbed nonionic surfactant is more effective per unit mass as a partitioning medium than the native soil organic matter for PAHs. When Kd* = Kd the corresponding initial concentration of surfactant was defined as critical washing concentration (CWC). Depending on the surfactant initial concentration below or above the CWC, the addition of nonionic surfactant can enhance the retardation of soil for PAHs or promote the removal of PAHs from soil, respectively. The values of Kd* and CWC can be predicted by a model, which correlates them with the compounds' octanol-water partition coefficients (Kow), soil property and the amount of soil-sorbed surfactant.     

Reduction of Cr(VI) by malic acid in aqueous Fe-rich soil suspensions

Detoxification of Cr(VI) through reduction by organic reductants has been regarded as an effective way for remediation of Cr(VI)-polluted soils. However, such remediation strategy would be limited in practical applications due to the low Cr(VI) reduction rate. In this study, the catalytic effect of two Fe-rich soils (Ultisol and Oxisol) on Cr(VI) reduction by malic acid was evaluated. As the results shown, the two soils could obviously accelerate the reduction of Cr(VI) by malic acid at low pH conditions, while such catalytic effect was gradually suppressed as the increase in pH. After reaction for 48 h at pH 3.2, Oxalic acid was found in the supernatant of Ultisol, suggesting the oxidization of hydroxyl in malic acid to carboxyl and breakage of the bond between C₂ and C₃. It was also found that the catalytic reactivity of Ultisol was more significant than that of Oxisol, which could be partly attributed to the fact that the amount of Fe(II) released from the reductive dissolution of Ultisol by malic acid was larger than that of Oxisol. With addition of Al(III), the catalytic effect from Ultisol was inhibited across the pH range examined. On the contrary, the presence of Cu(II) would increase the catalytic effect of Ultisol, which was more pronounced with the increase in pH. This study proposed a potential way for elimination of the environmental risks posed by the Cr(VI) contamination by use of the natural soil surfaces to catalyze Cr(VI) reduction by the organic reductant such as malic acid, a kind of organic reductant originating from soil organic decomposition process or plant excretion.     

Phenanthrene partitioning in sediment–surfactant–fresh/saline water systems

The objective of this study was to investigate the influence of salinity on the effectiveness of surfactants in the remediation of sediments contaminated with phenanthrene (PHE). This is an example of a more general application of surfactants in removing hydrophobic organic compounds (HOCs) from contaminated soil/sediment in saline environments via in-situ enhanced sorption or ex-situ soil washing. Salinity effects on surfactant micelle formation and PHE partitioning into solution surfactant micelles and sorbed surfactant were investigated. The critical micelle concentration of surfactants decreased, and PHE partition between surfactant micelles and water increased with increasing salinity. Carbon-normalized partition coefficients (K_ss) of PHE onto the sorbed cationic surfactant increased significantly with increasing salinity, which illustrates a more pronounced immobilization of PHE by cationic surfactant in a saline system. Reduction of PHE sorption by anionic surfactant was more pronounced in the saline system, indicating that the anionic surfactant has a higher soil washing effectiveness in saline systems.