An investigation of anthraquinone dye biodegradation by immobilized Aspergillus flavus in fluidized bed bioreactor

Purpose

Biodegradation and biodecolorization of Drimarene blue K₂RL (anthraquinone) dye by a fungal isolate Aspergillus flavus SA2 was studied in lab-scale immobilized fluidized bed bioreactor (FBR) system.

Method

Fungus was immobilized on 0.2-mm sand particles. The reactor operation was carried out at room temperature and pH?5.0 in continuous flow mode with increasing concentrations (50, 100, 150, 200, 300, 500?mg?l^?1) of dye in simulated textile effluent on the 1st, 2nd, 5th, 8th, 11th, and 14th days. The reactors were run on fill, react, settle, and draw mode, with hydraulic retention time (HRT) of 24?C72?h. Total run time for reactor operation was 17?days.

Results

The average overall biological oxygen demand (BOD), chemical oxygen demand (COD), and color removal in the FBR system were up to 85.57%, 84.70%, and 71.3%, respectively, with 50-mg?l^?1 initial dye concentration and HRT of 24?h. Reductions in BOD and COD levels along with color removal proved that the mechanism of biodecolorization and biodegradation occurred simultaneously. HPLC and LC?CMS analysis identified phthalic acid, benzoic acid, 1, 4-dihydroxyanthraquinone, 2,3-dihydro-9,10-dihydroxy-1,4-anthracenedione, and catechol as degradation products of Drimarene blue K₂RL dye. Phytotoxicity analysis of bioreactor treatments provided evidence for the production of less toxic metabolites in comparison to the parent dye.

Conclusion

The present fluidized bed bioreactor setup with indigenously isolated fungal strain in its immobilized form is efficiently able to convert the parent toxic dye into less toxic by-products.     

Identification of cadmium-excluding welsh onion (Allium fistulosum L.) cultivars and their mechanisms of low cadmium accumulation

Purpose

Screening out cadmium (Cd) excluding cultivars of a crop in agricultural production is an effective way to prohibit Cd entering into food chain.

Methods

A judging criterion for Cd-excluding cultivars based on food safety was suggested and used in the identification of Cd-excluding welsh onion (Allium fistulosum L.) cultivars. A pot culture experiment was carried out to screen out Cd-excluding cultivars, of which the results were confirmed by plot experiments. The relevant factors of Cd accumulation in the pseudostem were analyzed and used in the correlation analysis aiming to study the low Cd accumulation mechanisms.

Results

The concentration of Cd in the pseudostem of welsh onions was 0.08?C0.20, 0.18?C0.41, and 0.26?C0.61?mg/kg fresh weight (FW) under three treatments (1.0, 2.5, and 5.0?mg/kg), respectively. The significant (p? ₃ ^? ?CN, and eight other elements in the tested welsh onion cultivars. Two cultivars were identified as Cd-excluding cultivars, mainly because the accumulation of Cd in their pseudostem was only 0.041?±?0.003 and 0.046?±?0.002?mg/kg FW, and 0.054?±?0.001 and 0.066?±?0.011?mg/kg FW, when growing in plots with Cd concentration of 0.49 and 0.99?mg/kg, respectively.

Conclusions

Ribentiegancongwang and Wuyeqi could be identified as Cd-excluding cultivars. Low bioaccumulation factor of the roots was the main mechanism of Cd-excluding welsh onion cultivars.     

Evaluation of substrate removal kinetics for UASB reactors treating chlorinated ethanes

Purpose

Lack of focus on the treatment of wastewaters bearing potentially hazardous pollutants like 1,1,2 trichloroethane and 1,1,2,2 tetrachloroethane in anaerobic reactors has provided an impetus to undertake this study. The objective of this exercise was to quantify the behavior of upflow anaerobic sludge blanket reactors and predict their performance based on the overall organic substrate removal.

Methods

The reactors (wastewater-bearing TCA (R2), and wastewater-bearing TeCA (R3)) were operated at different hydraulic retention times (HRTs), i.e., 36, 30, 24, 18, and 12?h corresponding to food-to-mass ratios varying in the range of 0.2?C0.7?mg chemical oxygen demand (COD) mg^?1 volatile suspended solids day^?1. The process kinetics of substrate utilization was evaluated on the basis of experimental results, by applying three mathematical models namely first order, Grau second order, and Michaelis-Menten type kinetics.

Results

The results showed that the lowering of HRT below 24?h resulted in reduced COD removal efficiencies and higher effluent pollutant concentrations in the reactors. The Grau second-order model was successfully applied to obtain the substrate utilization kinetics with high value of R ² (>0.95). The Grau second-order substrate removal constant (K ₂) was calculated as 1.12 and 7.53?day^?1 for reactors R2 and R3, respectively.

Conclusion

This study demonstrated the suitability of Grau second-order kinetic model over other models, for predicting the performance of reactors R2 and R3, in treating wastewaters containing chlorinated ethanes under different organic and hydraulic loading conditions.     

Degradation and mineralization of sulcotrione and mesotrione in aqueous medium by the electro-Fenton process: a kinetic study

Introduction

The degradation and mineralization of two triketone (TRK) herbicides, including sulcotrione and mesotrione, by the electro-Fenton process (electro-Fenton using Pt anode (EF-Pt), electro-Fenton with BDD anode (EF-BDD) and anodic oxidation with BDD anode) were investigated in acidic aqueous medium.

Methods

The reactivity of both herbicides toward hydroxyl radicals was found to depend on the electron-withdrawing effect of the aromatic chlorine or nitro substituents. The degradation of sulcotrione and mesotrione obeyed apparent first-order reaction kinetics, and their absolute rate constants with hydroxyl radicals at pH?3.0 were determined by the competitive kinetics method.

Results and discussion

The hydroxylation absolute rate constant (k _abs) values of both TRK herbicides ranged from 8.20?×?10⁸ (sulcotrione) to 1.01?×?10⁹ (mesotrione) L?mol^?1?s^?1, whereas those of the TRK main cyclic or aromatic by-products, namely cyclohexane 1,3-dione , (2-chloro-4-methylsulphonyl) benzoic acid and 4-(methylsulphonyl)-2-nitrobenzoic acid, comprised between 5.90?×?10⁸ and 3.29?×?10⁹?L?mol^?1?s^?1. The efficiency of mineralization of aqueous solutions of both TRK herbicides was evaluated in terms of total organic carbon removal. Mineralization yields of about 97?C98% were reached in optimal conditions for a 6-h electro-Fenton treatment time.

Conclusions

The mineralization process steps involved the oxidative opening of the aromatic or cyclic TRK by-products, leading to the formation of short-chain carboxylic acids, and, then, of carbon dioxide and inorganic ions.     

Copper chitosan nanocomposite: synthesis, characterization, and application in removal of organophosphorous pesticide from agricultural runoff

Purpose

Removal of malathion from agricultural runoff was studied using novel copper-coated chitosan nanocomposite (CuCH)??a biopolymeric waste obtained from marine industry.

Methods

Synthesis and characterization of the adsorbent using different spectral techniques like Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy, energy-dispersive X-ray spectroscopy, Brunauer, Emmett, and Teller surface analyzer have been carried out. Equilibrium studies have been carried out to optimize the dose rate, pH, and the reaction time. Parathion and methyl parathion removal were also evaluated by CuCH in the batch mode. Using gas chromatography?Cmass spectrometry (GC?CMS) and FTIR studies suitable mechanism for adsorption has been suggested.

Results

The particle size of the adsorbent ranged from 700 to 750?nm. The surface area was found to be 20?m²?g^-1 with a pore volume of 0.11?cc?g^-1. The maximum adsorption capacity of malathion by CuCH was found to be 322.6?±?3.5?mg?g^-1 at an optimum pH of 2.0. Presence of copper ions enhanced the adsorption capacity of the adsorbent. The reaction was found to follow pseudo second-order kinetics with a rate constant of 0.53?g?mg^-1?min^-1. Evidence from FTIR indicated that copper ions form a dithionate complex with malathion during the adsorption stage. The adsorbent was found to remove malathion completely from spiked concentration of 2?mg?l^-1 in the agricultural run-off samples. It was also found that CuCH removed other organophospurous pesticides like methyl parathion and parathion under prevailing conditions.

Conclusions

The results indicated that CuCH could be applied for the removal of organophosphorous pesticides.     

Acute effect of benzo[a]anthracene on the biodegradation of peptone under aerobic conditions

Background

This study investigated the acute effect of benzo[a]anthracene, a significant compound among polycyclic aromatic hydrocarbons, on the biodegradation of a synthetic organic substrate??a peptone/meat extract mixture??under aerobic conditions.

Methods

A laboratory-scale sequencing batch reactor was sustained at steady state at a sludge age of 10?days with substrate feeding. Inhibition tests involved running a series of batch reactors initially seeded with the biomass obtained from the parent reactor. After the biomass seeding, the reactors were started with the peptone mixture and a range of initial benzo[a]anthracene concentrations between 0.5 and 88?mg/L. Experimental profiles of oxygen uptake rates and polyhydroxyalkanoates were evaluated by calibration of a selected model.

Results

Lower doses of benzo[a]anthracene had no effect on process kinetics. The noticeable acute impact was only observed with the addition of 88?mg/L of benzo[a]anthracene, but it was limited with the storage mechanism: the amount of organic substrate diverted to polyhydroxyalkanoates was significantly reduced with a corresponding decrease in the maximum storage rate, k _STO, from 2.7 down to 0.6?day^?1. Similarly, the maximum growth rate from internally stored polyhydroxyalkanoates was lowered from 2.3 to 1.0?day^?1.

Conclusion

Among the mechanisms for direct substrate utilization, only the hydrolysis rate was slightly reduced, but otherwise, the overall COD removal efficiency was not affected.     

Aquatic photochemistry of paracetamol in the presence of dissolved organic chromophoric material and nitrate

Purpose

This study contains some new findings connected to the photolysis of the drug paracetamol (hereinafter APAP) especially in light of estimating natural conditions, and it will offer information to better evaluate environmental problems connected with this widely used analgesic agent. Only a few studies, so far, have focussed on the photodegradation process of APAP in the natural environment, and the question about the role of the colored/chromophoric dissolved organic matter (CDOM) and nitrate (NO ₃ ^? ) as photoinductors is almost open.

Methods

APAP dissolved in freshwater and pure laboratory water in the presence and absence of CDOM and NO ₃ ^? ions was irradiated using weak-energy photon energies simulating natural conditions.

Results

CDOM and NO ₃ ^? as photoinductors produced only the slow phototransformation of APAP under weak energy radiation, and APAP seemed to be practically resistant to direct photolysis under weak radiant energies available in natural conditions. The estimated reaction efficiencies, in addition to half-lives, speak for that NO ₃ ^? and CDOM do not act as quite independent photoinductors but their effect in conjunction (CDOM?CNO ₃ ^? ?Cwater) is stronger than the separate ones. The principal phototransformation intermediates of APAP were mono-hydroxy derivatives, depending on available photon energies formed via ortho- or meta-hydroxylation, possessing substantial power of resistance to further specific transformation reactions.

Conclusions

The estimated half-life of the phototransformation of APAP in the natural aqueous environment and in the presence of suitable photoinductors will be about 30?days or more.     

Aquatic ecotoxicity assessment of a new natural formicide

Background, aim and scope

Agrochemicals could reach aquatic ecosystems and damage ecosystem functionality. Natural formicide could be an alternative to use in comparison with the more toxic formicides available on the market. Thus, the objective of this study was to assess the ecotoxicity of the new natural formicide Macex? with a battery of classical aquatic ecotoxicity tests.

Material and methods

Bacteria (Aliivibrio fischeri), algae (Pseudokirchneriella subcapitata), hydra (Hydra attenuata), daphnids (Daphnia magna), and fish (Danio rerio) tests were performed in accordance with international standardized methodologies.

Results

In the range of formicide concentrations tested (0.03 to 2.0?g?L^?1) EC₅₀ values varied from 0.49 to >2.0?g?L^?1, with P. subcapitata being the most sensitive species and H. attenuata and D. rerio the most tolerant species to this product in aqueous solutions.

Conclusions

This new formicide preparation can be classed as a product of low toxicity compared to the aquatic ecotoxicity of the most common commercialized formicides.     

Synthesis of α-Fe2O3 nanofibers for applications in removal and recovery of Cr(VI) from wastewater

Purpose

Nanomaterials such as iron oxides and ferrites have been intensively investigated for water treatment and environmental remediation applications. The purpose of this work is to synthesize α-Fe₂O₃ nanofibers for potential applications in removal and recovery of noxious Cr(VI) from wastewater.

Methods

α-Fe₂O₃ nanofibers were synthesized via a simple hydrothermal route followed by calcination. The crystallographic structure and the morphology of the as-prepared α-Fe₂O₃ nanofibers were characterized by X-ray diffraction, scanning electron microscope, and transmission electron microscope. Batch adsorption experiments were conducted, and Fourier transform infrared spectra were recorded before and after adsorption to investigate the Cr(VI) removal performance and adsorption mechanism. Langmuir and Freundlich modes were employed to analyze the adsorption behavior of Cr(VI) on the α-Fe₂O₃ nanofibers.

Results

Very thin and porous α-Fe₂O₃ nanofibers have been successfully synthesized for investigation of Cr(VI) removal capability from synthetic wastewater. Batch experiments revealed that the as-prepared α-Fe₂O₃ nanofibers exhibited excellent Cr(VI) removal performance with a maximum adsorption capacity of 16.17 mg g^?1. Furthermore, the adsorption capacity almost kept unchanged after recycling and reusing. The Cr(VI) adsorption process was found to follow the pseudo-second-order kinetics model, and the corresponding thermodynamic parameters ΔG°, ΔH°, and ΔS° at 298 K were calculated to be ?26.60 kJ?mol^?1, ?3.32 kJ?mol^?1, and 78.12 J?mol^?1 K^?1, respectively.

Conclusions

The as-prepared α-Fe₂O₃ nanofibers can be utilized as efficient low-cost nano-absorbents for removal and recovery of Cr(VI) from wastewater.     

Reduction of dinitrotoluene sulfonates in TNT red water using nanoscale zerovalent iron particles

Purpose

This research was designed to investigate the feasibility of converting the dinitrotoluene sulfonates (DNTS) in TNT red water into the corresponding aromatic amino compounds using nanoscale zerovalent iron (NZVI).

Methods

NZVI particles were simultaneously synthesized and stabilized by sodium borohydride reduction in a nondeoxygenated system. The morphology, elemental content, specific surface area, and crystal properties of the NZVI were characterized before and after the reaction by environmental scanning electron microscope; energy dispersive X-ray; Brunauer, Emmett, and Teller; and X-ray diffraction, respectively. The reduction process was conducted at pH?=?6.3 at ambient temperature. The efficiency of the NZVI-mediated DNTS reduction process was monitored by HPLC, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy analyses.

Results

The properties of the NZVI particles prepared were found to be similar to those obtained through oxygen-free preparation and inert stabilization processes. Both 2,4-DNT-3-sulfonate (2,220?mg?L^?1) and 2,4-DNT-5-sulfonate (3,270?mg?L^?1) in TNT red water underwent a pseudo-first-order transformation when mixed with NZVI at room temperature and near-neutral pH. Their observed rate constants were 0.11 and 0.30?min^?1, respectively. Within 1?h of processing, more than 99% of DNTS was converted by NZVI-mediated reduction into the corresponding diaminotoluene sulfonates.

Conclusions

NZVI can be simultaneously prepared and stabilized in a nondeoxygenated system. NZVI reduction is a highly efficient method for the conversion of DNTS into the corresponding diaminotoluene sulfonates under near-neutral pH conditions. Therefore, NZVI reduction may be useful in the treatment of TNT red water and subsequent recovery of diaminotoluene from explosive wastewater.     

Characterization of PM10 atmospheric aerosol at urban and urban background sites in Fuzhou city, China

Background

PM₁₀ aerosol samples were simultaneously collected at two urban and one urban background sites in Fuzhou city during two sampling campaigns in summer and winter. PM₁₀ mass concentrations and chemical compositions were determined.

Methods

Water-soluble inorganic ions (Cl^?, NO ₃ ^? , SO ₄ ^2? , NH ₄ ⁺ , K⁺, Na⁺, Ca²⁺, and Mg²⁺), carbonaceous species (elemental carbon and organic carbon), and elements (Al, Si, Mg, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Br, and Pb) were detected using ion chromatography, thermal/optical reflectance, and proton-induced X-ray emission methods, respectively.

Results

PM₁₀ mass concentrations, as well as most of the chemical components, were significantly increased from urban background to urban sites, which were due to enhanced anthropogenic activities in urban areas. Elements, carbonaceous species, and most of the ions were more uniformly distributed at different types of sites in winter, whereas secondary ion SO ₄ ^2? , NO ₃ ^? , and NH ₄ ⁺ showed more evident urban-background contrast in this season. The chemical mass closure indicated that mineral dust, organic matters, and sulfate were the most abundant components in PM₁₀. The sum of individually measured components accounted for 86.9?C97.7% of the total measured PM₁₀ concentration, and the discrepancy was larger in urban area than in urban background area.

Conclusion

According to the principal component analysis?Cmultivariate linear regression model, mineral dust, secondary inorganic ions, sea salt, and motor vehicle were mainly responsible for the PM₁₀ particles in Fuzhou atmosphere, and contributed 19.9%, 53.3%, 21.3%, and 5.5% of PM₁₀, respectively.     

Lead concentration increase in the hepatic and gill soluble fractions of European chub (Squalius cephalus)—an indicator of increased Pb exposure from the river water

Purpose

To examine if chronic exposure of feral fish to elevated Pb concentrations in the river water (up to 1???g?L^?1), which are still lower than European recommendations for dissolved Pb in surface waters (7.2???g?L^?1; EPCEU (Official J L 348:84, 2008)), would result in Pb accumulation in selected fish tissues.

Methods

Lead concentrations were determined by use of HR ICP-MS in the gill and hepatic soluble fractions of European chub (Squalius cephalus) caught in the Sutla River (Croatia?CSlovenia).

Results

At the site with increased dissolved Pb in the river water, soluble gill Pb levels (17.3???g?L^?1) were approximately 20 times higher compared to uncontaminated sites (0.85???g?L^?1), whereas the ratio between contaminated (18.1???g?L^?1) and uncontaminated sites (1.17???g?L^?1) was lower for liver (15.5). Physiological variability of basal Pb concentrations in soluble gill and hepatic fractions associated to fish size, condition, sex, or age was not observed, excluding the possibility that Pb increase in chub tissues at contaminated site could be the consequence of studied biotic parameters. However, in both tissues of Pb-exposed specimens, females accumulated somewhat more Pb than males, making female chubs potentially more susceptible to possible toxic effects.

Conclusions

The fact that Pb increase in gill and hepatic soluble fractions of the European chub was not caused by biotic factors and was spatially restricted to one site with increased dissolved Pb concentration in the river water points to the applicability of this parameter as early indicator of Pb exposure in monitoring of natural waters.     

Enhancement of natural radioactivity in fertilized soil of Faisalabad, Pakistan

Background, goal, and scope

Natural radioactivity in phosphate rock (PR) is transferred to phosphate fertilizer (PF) during the manufacturing process of the PF. The continuous addition of the PF to the cultivated soil accumulates the radionuclides in the land and increases the level of radioactivity in the soil. The purpose of the present study was to investigate the enhanced level of accumulated radioactivity due to the continuous addition of the PF in the farmlands of Nuclear Institute of Agriculture and Biology (NIAB) at Faisalabad in Pakistan. The selected study area consisted of the highly fertilized farmlands and an unfertilized barren land of the NIAB.

Introduction

The understudy area is very fertile for the growth of various types of crops; therefore, four agricultural research institutes have been established at Faisalabad and NIAB is one of those. The NIAB has developed various research farmlands at different places in Pakistan. The crop yield has been increased by adding various fertilizers in the farmlands. The addition of the PF accompanied with the radionuclides enhances radioactivity in the fields. Human being is exposed directly or indirectly to this radiological hazard. A prolong exposure may become a cause of health risk.

Materials and methods

The area of study consisted of three types of lands: the land under cultivation for the last 40 and 30?years called Site 1 and Site 2, respectively, and the barren land was called Site 3. A total of 75 soil samples were collected within the crop rooting zone (up to 25?cm deep) of the soil of the NIAB farms. The samples were dried, pulverized to powder, sealed in plastic containers, and stored to achieve equilibrium between ²²⁶Ra and ²²²Rn. Activity concentrations of the radionuclides ²³⁸U (²²⁶Ra), ²³²Th, and ⁴⁰K in soil samples were determined by using a high resolution gamma ray spectrometry system, consisting of an high purity germanium detector coupled through a spectroscopy amplifier with a PC based MCA installed with Geni-2000 software.

Results

The measured activity concentration levels of ⁴⁰K were 662?±?15, 615?±?17, and 458?±?20?Bq?kg^?1, ²²⁶Ra were 48?±?6, 43?±?5, and 26?±?4?Bq?kg^?1, and that of ²³²Th were 39?±?5, 37?±?5, 35?±?5?Bq?kg^?1, respectively, in the soil of the Sites 1, 2, and 3. Gamma dose rate 1?m above the soil surface was 55, 51, and 40?nGy?h^?1 from Sites 1, 2, and 3, respectively. External dose rates in the rooms constructed of the bricks made of the soil from Sites 1, 2, and 3 were 161, 149, and 114?nGyh^?1, respectively.

Discussions

Activity concentration values of ⁴⁰K and ²²⁶Ra in the soil of Sites 1 and 2 were higher than that in the soil of Site 3. The relative rise of ⁴⁰K was 43?% and 34?% and that of ²²⁶Ra was 85?% and 65?% respectively in these sites. Activity concentrations of ²³²Th in all these sites were in the background range. Gamma dose rate 1?m above soil surface of Sites 1 and 2 was 40?% and 30?% respectively higher than that from the soil of Site 3. The rise in activity of ⁴⁰K and ²²⁶Ra and gamma dose from the Site 1 was greater than that from the Site 2. The least activity and dose were observed from the Site 3. Gamma dose in the dwellings made of fertilized soil bricks of Site 1 and Site 2 were respectively calculated to be 41?% and 32?% higher than that in the abodes made of unfertilized soil bricks of Site 3.

Conclusions

Activity concentrations of ²²⁶Ra and ⁴⁰K were observed to be enhanced in the fertilized farmlands of the NIAB. Outdoor and indoor gamma dose as radiological hazard were found to be increasing with the continuous addition of PF in the understudy farmlands.

Recommendations

It is recommended that naturally occurring radioactive metal should be removed during the process of manufacturing of the PF from the PR.

Prospective

The rise in radioactivity in the farmlands due to the addition of the PF can be a source of direct or indirect exposure to radiation that may enhance cancer risk of the exposed individuals.     

Adsorption of Remazol Red 198 onto magnetic N-lauryl chitosan particles: equilibrium, kinetics, reuse and factorial design

Purpose

The discharge of colored effluents from industries is an important environmental issue and it is indispensable to remove the dyes before the water gets back to the rivers. The magnetic adsorbents present the advantage of being easily separated from the aqueous system after adsorption by positioning an external magnetic field.

Methods

Magnetic N-lauryl chitosan (L-Cht/??-Fe₂O₃) particles were prepared and characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, transmission electron microscopy, and vibrating sample magnetometry. Remazol Red 198 (RR198) was used as a reactive dye model for adsorption on L-Cht/??-Fe₂O₃. The adsorption isotherms were performed at 25°C, 35°C, 45°C, and 55°C and the process was optimized using a 2³ factorial design (analyzed factors: pH, ionic strength, and temperature). The desorption and regeneration studies were performed in a three times cycle.

Results

The characterization of the material indicated that the magnetic particles were introduced into the polymeric matrix. The pseudo-second order was the best model for explaining the kinetics and the Langmuir?CFreundlich was the best-fitted isotherm model. At room temperature, the maximum adsorption capacity was 267?mg?g^?1. The material can be reused, but with a decrease in the amount of adsorbed dye.

Conclusions

L-Cht/??-Fe₂O₃ is a promising material to remove RR198 and probably other similar reactive dyes from aqueous effluents.     

Characteristics of precipitation chemistry at Lushan Mountain, East China: 1992–2009

Introduction

Trends in precipitation pH and conductivity during 1992?C2009, and in ionic compositions from January 2007 to June 2009, are reported from Lushan Mountain, one of the highest mountains in mid-east China. Annual mean pH was in the range of 4.35?C5.01 and showed a statistically very significant (P?P?Results and discussions Over the period of study, Lushan Mountain received more rainfall in spring and summer. The pH values varied seasonally with winter minima. The winter multiyear seasonal mean pH was 4.35. The corresponding summer value was 4.88. SO ₄ ^2? and NO ₃ ^? were the main anions, and NH ₄ ⁺ and Ca²⁺ the main cations. The anion to cation ratio was 0.8?C1.0, and that of [SO ₄ ^2? ] to [NO ₃ ^? ] was 2.4-3.0, much lower than that of the 1980s. However, sulfuric acid was still the main acid present. The ratio of [NH ₄ ⁺ ] to [Ca²⁺] was about 1.0, suggesting that these two alkaline substances provided close acid neutralizing capacity. The ratio of [Cl^?] to [Na⁺] was about 0.67, somewhat lower than that of natural precipitation.

Conclusions

Ionic composition varied seasonally and was closely correlated to the amounts of rainfall and pollution. Trajectory analyses showed that the trajectories to Lushan Mountain could be classified in six clusters and trajectories originating from the South Sea and the areas surrounding Lushan Mountain had the greatest impacts on precipitation chemistry.     

Bioremediation of chromium by novel strains Enterobacter aerogenes T2 and Acinetobacter sp. PD 12 S2

Purpose

This study had an objective to identify the most potent chromium-resistant bacteria isolated from tannery effluent and apply them for bioremediation of chromium in tannery effluents.

Methods

Two such strains (previously characterized and identified by us)??Enterobacter aerogenes (NCBI GenBank USA Accession no. GU265554) and Acinetobacter sp. PD 12 (NCBI GenBank USA Accession no. GU084179)??showed powerful chromium resistivity and bioremediation capabilities among many stains isolated from tannery waste. Parameters such as pH, concentration of hexavalent chromium or Cr (VI), and inoculum volume were varied to observe optimum bioconversion and bioaccumulation of Cr (VI) when the said strains were grown in M9 minimal salt media. E. aerogenes was used to remediate chromium from tannery effluents in a laboratory level experiment.

Results

Observation by Scanning Electron Microscope and chromium peak in Energy Dispersive X-ray Spectroscopic microanalysis revealed that E. aerogenes helped remediate a moderate amount of Cr (VI) (8?C16?mg?L^?1) over a wide range of pH values at 35?C37°C (within 26.05?h). High inoculum percentage of Acinetobacter sp. PD 12 also enabled bioremediation of 8?C16?mg?L^?1 of Cr (VI) over a wide range of temperature (25?C37°C), mainly at pH?7 (within 63.28?h). The experiment with real tannery effluent gave very encouraging results.

Conclusion

The strain E. aerogenes can be used in bioremediation of Cr (VI) since it could work in actual environmental conditions with extraordinarily high capacity.     

Acute and chronic toxicity of benzotriazoles to aquatic organisms

Purpose

Resulting from their intensive use as corrosion inhibitors in aircraft deicing and anti-icing fluids (ADAF) and for silver protection in dishwasher detergents benzotriazoles (BTs) are widespread in European surface waters. The current study aimed on an ecotoxicological characterization of 1H-benzotriazole (1H-BT) and 5-methyl-1H-benzotriazole (5MBT).

Methods

Acute and chronic OECD guideline tests were conducted with primary producers (Desmodesmus subspicatus, Lemna minor) and two daphnia species (Daphnia magna, Daphnia galeata) to characterize the hazard of these chemicals. Additionally, the estrogenic activity of both BTs was analyzed in vitro using a recombinant yeast estrogen screen (YES).

Results

Both BTs revealed significant effects in acute and chronic experiments, but exhibited no estrogenic activity in the YES. The algal growth test displayed an inhibited cell number increase with effect concentration (EC) values of EC₁₀ 1.18 and 2.86?mg?l^-1 for 1H-BT and 5MBT, respectively. In the Lemna test, EC₁₀ values were 3.94?mg?l^-1 (1H-BT) and 2.11?mg?l^-1 (5MBT). D. magna was also affected with EC₅₀ (48?h) values of 107?mg?l^-1 for 1H-BT and 51.6?mg?l^-1 for 5MBT. D. galeata was more sensitive with an EC₅₀ (48?h) of 14.7?mg 1H-BT l^-1 and 8.13?mg 5MBT l^-1. In the 21-day reproduction tests with D. magna, the EC₁₀ for 5MBT was 5.93?mg?l^-1 while 1H-BT showed no adverse effects. D. galeata turned out to be more sensitive in the chronic study with EC₁₀ values of 0.97?mg?l^-1 for 1H-BT and 0.40?mg?l^-1 for 5 MBT.

Conclusion

Because BTs are regularly found in the aquatic environment at lower ??g l^-1 concentrations reflecting their persistence and poor elimination during wastewater treatment processes, a preliminary risk assessment was conducted. There is little indication that BTs pose a risk for aquatic ecosystems at current exposure levels during most of the year. However, it cannot be excluded that in winter with a higher usage of ADAFs environmental concentrations may well exceed the level that is considered safe for aquatic organisms.     

In situ photoelectrochemical/photocatalytic study of a dye discoloration in a microreactor system using TiO2 thin films

Introduction

In this work, we report in situ studies of UV photoelectrocatalytic discoloration of a dye (indigo carmine) by a TiO₂ thin film in a microreactor to demonstrate the driving force of the applied electrode potential and the dye flow rate toward dye discoloration kinetics.

Methods

TiO₂ 65-nm-thick thin films were deposited by PVD magnetron sputtering technique on a conducting glass substrate of fluorinated tin oxide. A microreactor to measure the discoloration rate, the electrode potential, and the photocurrent in situ, was developed. The dye solutions, before and after measurements in the microreactor, were analyzed by Raman spectroscopy.

Results

The annealed TiO₂ thin films had anatase structure with preferential orientation (101). The discoloration rate of the dye increased with the applied potential to TiO₂ electrode. Further, acceleration of the photocatalytic reaction was achieved by utilizing dye flow recirculation to the microreactor. In both cases the photoelectrochemical/photocatalytic discoloration kinetics of the dye follows the Langmuir?CHinshelwood model, with first-order kinetics.

Conclusions

The feasibility of dye discoloration on TiO₂ thin film electrodes, prepared by magnetron sputtering using a flow microreactor system, has been clearly demonstrated. The discoloration rate is enhanced by applying a positive potential (E _AP) and/or increasing the flow rate. The fastest discoloration and shortest irradiation time (50?min) produced 80% discoloration with an external anodic potential of 0.931?V and a flow rate of 12.2?mL?min^?1.     

Modeling and optimization of reductive degradation of chloramphenicol in aqueous solution by zero-valent bimetallic nanoparticles

Purpose

The present study aims to investigate the individual and combined effects of temperature, pH, zero-valent bimetallic nanoparticles (ZVBMNPs) dose, and chloramphenicol (CP) concentration on the reductive degradation of CP using ZVBMNPs in aqueous medium.

Method

Iron?Csilver ZVBMNPs were synthesized. Batch experimental data were generated using a four-factor statistical experimental design. CP reduction by ZVBMNPs was optimized using the response surface modeling (RSM) and artificial neural network-genetic algorithm (ANN-GA) approaches. The RSM and ANN methodologies were also compared for their predictive and generalization abilities using the same training and validation data set. Reductive by-products of CP were identified using liquid chromatography-mass spectrometry technique.

Results

The optimized process variables (RSM and ANN-GA approaches) yielded CP reduction capacity of 57.37 and 57.10?mg?g^?1, respectively, as compared to the experimental value of 54.0?mg?g^?1 with un-optimized variables. The ANN-GA and RSM methodologies yielded comparable results and helped to achieve a higher reduction (>6%) of CP by the ZVBMNPs as compared to the experimental value. The root mean squared error, relative standard error of prediction and correlation coefficient between the measured and model-predicted values of response variable were 1.34, 3.79, and 0.964 for RSM and 0.03, 0.07, and 0.999 for ANN models for the training and 1.39, 3.47, and 0.996 for RSM and 1.25, 3.11, and 0.990 for ANN models for the validation set.

Conclusion

Predictive and generalization abilities of both the RSM and ANN models were comparable. The synthesized ZVBMNPs may be used for an efficient reductive removal of CP from the water.     

Microbial structure and chemical components of aerosols caused by rotating brushes in a wastewater treatment plant

Purpose

Bacterial community structure and the chemical components in aerosols caused by rotating brushes in an Orbal oxidation ditch were assessed in a Beijing municipal wastewater treatment plant.

Methods

Air samples were collected at different distances from the aerosol-generating rotating brushes. Molecular culture-independent methods were used to characterize the community structure of the airborne bacteria in each sample regardless of cell culturability. A clone library of 16S rDNA directly amplified from air DNA of each sample was constructed and sequenced to analyze the community composition and diversity. Insoluble particles and water-soluble ions emitted with microorganisms in aerosols were analysis by a scanning electron microscope together with energy dispersive X-ray spectroscopy and ion chromatogram analyzer.

Results

In total, most of the identified bacteria were Proteobacteria. The majority of sequences near the rotating brushes (the main source of the bioaerosols) were Proteobacteria (62.97 %) with ??-(18.52 %) and ??-(44.45?%) subgroups and Bacteroidetes (29.63 %). Complex patterns were observed for each sampling location, suggesting a highly diverse community structure, comparable to that found in water in the Orbal oxidation ditch. Accompany with microorganisms, 46.36???g/m³ of SO ₄ ^2? , 29.35???g/m³ of Cl^?, 21.51???g/m³ of NO ₃ ^? , 19.76???g/m³ of NH ₄ ⁺ , 11.42???g/m³ of PO ₄ ^3? , 6.18???g/m³ of NO ₂ ^? , and elements of Mg, Cl, K, Na, Fe, S, and P were detected from the air near the aerosols source.

Conclusions

Differences in the structure of the bacterial communities and chemical components in the aerosols observed between sampling sites indicated important site-related variability. The composition of microorganisms in water was one of the most important sources of bacterial communities in bioaerosols. Chemical components in bioaerosols may provide a media for airborne microorganism attachment, as well as a suitable microenvironment for their growth and survival in the air. This study will be benefit for the formulation of pollution standards, especially for aerosols, that take into account plant workers?? health.