Photocatalytic oxidation of pesticide rinsate

Pesticide rinsate has been considered as one of the major threats for the environment. In this study, photocatalysts such as TiO2 and O3 were used to promote the efficiency of direct UV photolysis to prevent such wastewater pollution. Carbofuran (a carbamate pesticide) and mevinphos (an organophosphate pesticide) with a concentration of 100 mg/L were selected as the test pesticide rinsates. Parent pesticide compound, COD, and microtoxicity analysis were employed to investigate the effect of photocatalyst on the degradation efficiency of pesticide in rinsate. It was found that the photocatalytic oxidation process (UV/O3, UV/TiO2) showed much higher COD removal and microtoxicity reduction efficiency for pesticide rinsate than did direct UV photolysis under the imposed conditions, suggesting that photocatalytic oxidation processes such as UV/O3 and UV/TiO2 could be a better alternative to treat pesticide rinsate. In addition, it was noted that increasing the initial pH of mevinphos rinsate to a basic level was required to reach higher COD removal efficiency and positive microtoxicity reduction efficiency while it was not necessary for the treatment of carbofuran rinsate.     

Enhancement of ozone oxidation and its associated processes in the presence of surfactant: degradation of atrazine

In this study, the degradation of atrazine (ATZ) by ozone (O3) oxidation and its associated processes (i.e. UV, UV/O3) in the presence and absence of surfactant was investigated and compared. A non-ionic surfactant, Brij 35, was selected. It was found that the presence of a low concentration of surfactant could improve the removal of ATZ by increasing the dissolution of ozone and the indirect generation of hydroxyl radicals. The saturated ozone level and the reaction rate constants were increased with increasing the concentration of surfactant and then decreased at higher surfactant doses at pH level of 2.5. A similar trend was observed at pH level of 7.0 in the presence of bicarbonate ion, because it is capable of deactivating the hydroxyl radicals generating at higher pH level. However, when the radical reactions become dominant in the ozonation (at pH 7.0 without bicarbonate), the saturated ozone level was higher than that with bicarbonate and the kinetic rate constants were increased first and levelled off with increasing of the dose of surfactant. Through the examining of a proposed unit performance index, the low concentration of surfactant is surely beneficial to the ozonation process. Besides, the direct photolysis and photo-assisted ozonation were compared to the ozonation. A significant enhancement on the decay rate of ATZ was resulted exclusively by adding the surfactant. An enhancement index for quantifying the improvement of the various processes was developed.     

Removal of 2-chlorophenol from water using rice-straw derived ash

Removal of 2-chlorophenol from water using rice-straw derived ash (RSDA) was evaluated in this study to compare with commercial activated carbon. RSDA was obtained by burning rice-straw at 400 °C and 700 °C for 1 h. This ash can provide a better adsorbent for 2-chlorophenol. The adsorption capacities of RSDA at 400 °C and 700 °C are 37 and 52 mg g?1 at pH 4, respectively, and decrease to 9.0 and 40 mg g?1 at pH 10. Adsorption of either neutral or anionic 2-cholorphenol by the RSDA are shown as L-shaped nonlinear isotherms, suggesting surface adsorption rather than partitioning is occurring. At higher-burning temperatures, the surface area, porosity, point of zero charge and aromaticity of the resultant RSDA increase, but the oxygen content and surface acidity decrease. The combined effects result in a higher 2-chlorophenol adsorption of RSDA at 700 °C, which shows a slight pH effect on the adsorption of 2-chlorophenol, due to the lower content of oxygen-containing functional groups. Oxygen-containing functional groups contribute to surface acidity and H-bonding sites for adsorbed water, which compromises the interaction between 2-chlorophenol and the adsorbents. Thus, it suggests that rice-straw derived carbon (RSDC) can be used as an effective low-cost substitute material for activated carbon for removal of chlorophenols from wastewater.     

Formation of hydroxylated and dimeric intermediates during oxidation of chlorinated phenols in aqueous solution

The oxidation of selected chlorophenols (2-chlorophenol, 4-chlorophenol, 2,4-dichlorophenol, 2,4,6-trichlorophenol, 2,3,4,6-tetrachlorophenol and pentachlorophenol) was studied in aqueous solutions using UV/H2O2 and O3 methods. The formation of oxidation intermediates was measured to elucidate their importance in the treatment of chlorophenols. Results indicated that chlorophenols can be treated efficiently by the methods studied, but the dechlorination of the compounds was insufficient. Analysis of intermediates in the acetylated extraction fractions showed that hydroxylation of chlorophenols and formation of dimeric products were involved in the oxidation of chlorophenols in both treatment processes. The majority of the intermediates detected were transient, and thus were not detectable after an extended treatment time. The presence of a complicated mixture of intermediates suggests the need for toxicity testing to confirm the detoxifying effect of the chemical oxidation of chlorophenols.     

The enhancement of the biodegradability of phenolic solution using preozonation based on high ozone utilization

In this research, the effects of preozonation on the biodegradability of 4-cresol, 4-nitrophenol and 2-chlorophenol solutions were investigated using a new gas-inducing reactor with high ozone utilization rate. The extent of preozonation may be monitored by determining the characteristic ozonation behaviors of preozonized phenolic solutions, such as residual phenolic concentration, ADMI value and ozone gas outlet concentration. Experimental results showed that as the initial phenolic compounds decomposed completely, the ozone gas outlet concentration rapidly increases. In addition, at pH 7, a peak ADMI value appears during the preozonation of 4-cresol and 2-chlorophenol, while for 4-nitrophenol the ADMI value decreases monotonically. Based on the characteristic ozonation behaviors and the ozone utilization rate, three characteristic times were chosen in order to have better control on the extent of preozonation. The effect of preozonation on the biodegradability of preozonized phenolic solution was studied based on these characteristic times. The intermediate products during the preozonation were also identified. The variation of BOD5 is strongly dependent on the accumulation of intermediate products. It is suggested that the best characteristic time is as the rapid increase of ozone gas outlet concentration in this study. The biodegradability (BOD5/COD) of preozonized 4-cresol, 2-chlorophenol and 4-nitrophenol solutions increase to 0.18, 0.26 and 0.33, respectively, for the best characteristic time.     

Photosonochemical degradation of trichloroacetic acid in aqueous solution

The degradation of trichloroacetic acid (TCA) was studied with ultraviolet (UV) photolysis, ultrasound (US) sonolysis and their combination. It was found that the degradation in the combined processes was more significant than in the UV photolysis or sonolysis alone. The effects of pH and dissolved gases on the rate of photosonochemical degradation of TCA were investigated and the degradation kinetics, mechanism and possible degradation products were discussed in detail.     

活性炭纤维上4-氯酚及焦化废水尾水的O3催化氧化降解实验研究

选择YT-1000型活性炭纤维（ACF）作为催化剂,考察ACF与O₃协同作用催化降解水溶液中4-氯酚的最佳反应条件,并将该条件应用于焦化废水生物处理尾水中难降解有机污染物的催化氧化。ACF表面具有丰富的微孔结构,对4-氯酚有良好的吸附作用,在动力学上提高了其与O3反应的起始浓度,并且在ACF表面含氧、含氮等基团的催化作用下发生氧化反应,1 L浓度为100 mg/L的4-氯酚水样中投加2 g ACF反应6 min时,吸附作用对TOC的去除率为43.4%,而ACF协同O₃作用时的TOC去除率提高到72.5%,协同增效作用为67.1%;在选定的反应条件下,ACF协同O₃降解焦化废水生物处理尾水,60 min时的TOC与色度的去除率分别达到56.8%和96.3%。上述研究过程证明了吸附作用与催化作用的协同能有效降解生物过程不能降解的焦化废水中惰性有机污染物。     

Photodegradation of the antimicrobial triclocarban in aqueous systems under ultraviolet radiation

This work aimed to investigate the effectiveness of ultraviolet (UV) radiation on the degradation of the antimicrobial triclocarban (TCC). We investigated the effects of several operational parameters, including solution pH, initial TCC concentration, photocatalyst TiO₂ loading, presence of natural organic matter, and most common anions in surface waters (e.g., bicarbonate, nitrate, and sulfate). The results showed that UV radiation was very effective for TCC photodegradation and that the photolysis followed pseudo-first-order kinetics. The TCC photolysis rate was pH dependent and favored at high pH. A higher TCC photolysis rate was observed by direct photolysis than TiO₂ photocatalysis. The presence of the inorganic ions bicarbonate, nitrate, and sulfate hindered TCC photolysis. Negative effects on TCC photolysis were also observed by the addition of humic acid due to competitive UV absorbance. The main degradation products of TCC were tentatively identified by gas chromatograph with mass spectrometer, and a possible degradation pathway of TCC was also proposed.     

Photochemistry and environment IV- Photochemical behaviour of monochlorophenols in dilute aqueous solution

The photochemical behaviour of chlorophenols is different to that of non-halogenated phenols. In the former, the first step is a C-Cl bond scission, which is not influenced by oxygen. Chlorine is converted into hydrochloric acid. For monochlorophenols, the position of the chlorine on the ring strongly influences the transformation. In the molecular form, 2-chlorophenol is converted into pyrocatechol. In the anionic form however, it is reduced in a cyclopentadienic acid which dimerizes according to a Diels-Alder reaction. The irradiation of 3-chlorophenol leads to resorcinol whatever the pH. This would appear to suggest a photohydrolysis mechanism. With 4-chlorophenol, the photochemical conversion is not so specific. Hydroquinone is formed (mainly in aerated solution), along with polyphenolic oligomers. A radical mechanism is proposed.     

A combined photolytic-electrolytic system for the simultaneous recovery of copper and degradation of phenol or 4-chlorophenol in mixed solutions

The effects of the presence of copper on the photooxidation of phenol and 4-chlorophenol and of the presence of the phenols on the recovery of copper by electrodeposition are studied in three systems: a photolytic cell in the presence and absence of TiO2 as a catalyst or H2O2 as an oxidant; an electrolytic cell and a combined photolytic-electrolytic system. The optimum system for the simultaneous removal of copper and destruction of the phenols which overcomes the effects of copper-phenol reactions is a combined system with concentrator electrode technology incorporated into the electrolytic cell. This combined system achieves >99% removal of copper and destruction of phenol or 4-chlorophenol in an 8 h period.     

Atrazine removal by ozonation processes in surface waters

Atrazine (6-chloro-N-ethyl-N'-isopropyl-1,3,5-triazinedyl-2,4-diamine) was treated with ozone alone and in combination with hydrogen peroxide or UV radiation in three surface waters. Experiments were carried out in two bubble reactors operated continuously. Variables investigated were the ozone partial pressure, temperature, pH, mass flow ratio of oxidants fed: hydrogen peroxide and ozone and the type of oxidation including UV radiation alone. Residence time for the aqueous phase was kept at 10 min. Concentrations of some intermediates, including deethylatrazine, deisopropylatrazine and deethyldeisopropylatrazine, were also followed. The nature of water, specifically the alkalinity and pH were found to be important variables that affected atrazine (ATZ) removal. Surface waters with low alkalinity and high pH allowed the highest removal of ATZ to be reached. There was an optimum hydrogen peroxide to ozone mass flow ratio that resulted in the highest ATZ removal in each surface water treated. This optimum was above the theoretical stoichiometry of the process. Therefore, to reach the maximum removal of ATZ in a O3/H2O2 process, more hydrogen peroxide was needed in the surface waters treated than in ultrapure water under similar experimental conditions. In some cases, UV radiation alone resulted in the removal of ATZ higher than ozonation alone. This was likely due to the alkalinity of the surface water. Ozonation and UV radiation processes yield different amounts of hydrogen peroxide. Combined ozonations (O3/H2O2 and O3/UV) lead to ATZ removals higher than single ozonation or UV radiation but the formation of intermediates was higher.     

超声波-光催化氧化降解邻氯苯酚的研究

对超声波一光催化氧化降解邻氯苯酚(2-cp)进行了研究．探讨了溶液初始pH、TiO2投加量、H2O2投加量和溶液初始浓度对2-cp降解率的影响。并对几种不同处理方法降解2-cp的结果进行了对比。结果表明,超声波和紫外光的协同效果明显,在相同的反应时间内,超声波能够明显提高光催化降解2-cp的降解率。超声波和紫外光连用,具有良好的工业应用前景。     

光催化-臭氧氧化降解H酸的研究

采用光催化一臭氧氧化技术（催化膜／UV／O3）降解H酸。研究结果表明，光催化与臭氧氧化相结合具有明显的协同作用。实验进一步讨论了臭氧投加量、废水初始pH值和H酸初始浓度对光催化一臭氧氧化降解H酸的影响。降解后的H酸，萘环结构被破坏，可生化性提高。     

光催化-臭氧氧化降解H酸的研究

采用光催化-臭氧氧化技术(催化膜/UV/O3)降解H酸.研究结果表明,光催化与臭氧氧化相结合具有明显的协同作用.实验进一步讨论了臭氧投加量、废水初始pH值和H酸初始浓度对光催化-臭氧氧化降解H酸的影响.降解后的H酸,萘环结构被破坏,可生化性提高.     

Carbonyls in the metropolitan area of Mexico City: calculation of the total photolytic rate constants Kp(s(-1)) and photolytic lifetime (tau) of ambient formaldehyde and acetaldehyde

A great number of studies on the ambient levels of formaldehyde and other carbonyls in the urban rural and maritime atmospheres have been published because of their chemical and toxicological characteristics, and adverse health effects. Due to their toxicological effects, it was considered necessary to measure these compounds at different sites in the metropolitan area of Mexico City, and to calculate the total rate of photolytic constants and the photolytic lifetime of formaldehyde and acetaldehyde. Four sites were chosen. Sampling was carried out at different seasons and atmospheric conditions. The results indicated that formaldehyde was the most abundant carbonyl, followed by acetone and acetaldehyde. Data sets obtained from the 4 sites were chosen to calculate the total rate of photolysis and the photolytic lifetime for formaldehyde and acetaldehyde. Maximum photolytic rate values were obtained at the maximum actinic fluxes, as was to be expected.     

Chemical degradation of chlorophenols with Fenton's reagent (Fe + H2O2)

Aqueous solutions of Fenton's reagent (Fe²⁺ + H₂O₂) have been used to effect the total decomposition of the chlorophenols: 2-chlorophenol, 3-chlorophenol, 4-chlorophenol, 3,4-dichlorophenol and 2,4,5-trichlorophenol. The mineralization of these chlorinated aromatic substrates to CO₂ and free Cl⁻ has been studied as a function of [Fe²⁺] and [HClO₄]. Increasing the concentration of Fe²⁺ enhances the decomposition process, while an increase in the concentration of HClO₄, inhibits the reaction. The presence of Fe³⁺ alone (without any Fe²⁺) with H₂O₂ has no effect on the degradation of the chlorophenols. In all cases, the stoichiometric quantity of free Cl⁻ was obtained at the completion of the decomposition reaction; but the rates of disappaearance of the chlorophenol and of the formation of the Cl⁻ are not similar. This suggests that some chlorinated aliphatic species may be formed as possible intemediates.     

Characteristics of MnO2 catalytic ozonation of sulfosalicylic acid and propionic acid in water

The characteristics of different types of MnO₂ catalytic ozonation of sulfosalicylic acid (SSal) and propionic acid (PPA) have been investigated in this paper. The experimental results show the dependence of catalytic activity of MnO₂ on organic compounds and the pH of solutions, but it is independent on the type of MnO₂. For example, three types of MnO₂ have not any catalytic activity when ozonation of PPA under the condition of this experiment. All MnO₂ catalytic ozonation of SSal at pH=1.0 have a greater total organic carbon removal than ozonation alone has, however, at pH=6.8 and 8.5, catalytic efficiency is not observed. Furthermore, the batch experimental results indicate that there are no direct relationship between the activity of metal oxide catalytic decomposition of ozone and that of its catalytic degradation of organic compounds.     

Ozonation of Procaine Penicillin G formulation effluent Part I: Process optimization and kinetics

Ozonation characteristics of synthetic Procaine Penicillin G (PPG) formulation effluent were investigated in a semi-batch ozone reactor at different pH (3, 7 and 12), ozone feed rates (600-2600 mg h-1) and COD values (200-600 mg l-1). Ozonation of aqueous PPG effluent resulted in 37 (82)% COD removal after 60 (120) min ozonation when the reaction pH was kept constant at pH=7.900 mg l-1 (corresponding to 50% of the total introduced) ozone was absorbed during a reaction period of 1 h. The effects of increasing the applied ozone dose and the initial COD on the COD abatement rates of PPG effluent were also studied. Results have indicated that increasing the ozone dose and decreasing the COD content both have positive effects on COD removal rates. The significant contribution of the free radical (.OH) reaction pathway to PPG ozonation could be traced using tert-butyl alcohol as the .OH probe compound at varying concentrations. The bimolecular reaction rate constants for the direct reaction of PPG with ozone were found as 152 and 2404 M-1 h-1 at pH=3 and 7, respectively, using the gas phase ozone partial pressures determined from of the outlet gas stream analysis. It could be demonstrated that ozone decomposition to free radicals being triggered by increasing the pH from 3 to 7 is essential for the rate enhancement of PPG effluent ozonation.     

Degradation of chlorophenols in aqueous media using UV XeBr excilamp in a flow-through reactor

2-Chlorophenol (2-CP), 4-chlorophenol (4-CP) and 2,4-dichlorophenol (2,4-DCP) at initial concentrations of 10, 20, 50 and 100mg l(-1) were degraded in aqueous media by direct UV photolysis using dielectric barrier discharge XeBr( *) excilamp (283nm) in a flow-through photoreactor. The pseudo-first order rate constants were highest and half-life times were lowest for 4-CP. The rates of photolysis under the experimental conditions increased in the order: 2-CP<2,4-DCP<4-CP. The intermediates of photolysis were identified by GC-MS and HPLC. The evolution of hydroquinone and p-benzoquinone as major intermediates of 4-CP photolysis was monitored.     

Potential interferences in photolytic nitrogen dioxide converters for ambient air monitoring: Evaluation of a prototype

ABSTRACT

Mixing ratios of the criteria air contaminant nitrogen dioxide (NO₂) are commonly quantified by reduction to nitric oxide (NO) using a photolytic converter followed by NO-O₃ chemiluminescence (CL). In this work, the performance of a photolytic NO₂ converter prototype originally designed for continuous emission monitoring and emitting light at 395 nm was evaluated. Mixing ratios of NO₂ and NO_x (= NO + NO₂) entering and exiting the converter were monitored by blue diode laser cavity ring-down spectroscopy (CRDS). The NO₂ photolysis frequency was determined by measuring the rate of conversion to NO as a function of converter residence time and found to be 4.2 s^?1. A maximum 96% conversion of NO₂ to NO over a large dynamic range was achieved at a residence time of (1.5 ± 0.3) s, independent of relative humidity. Interferences from odd nitrogen (NO_y) species such as peroxyacyl nitrates (PAN; RC(O)O₂NO₂), alkyl nitrates (AN; RONO₂), nitrous acid (HONO), and nitric acid (HNO₃) were evaluated by operating the prototype converter outside its optimum operating range (i.e., at higher pressure and longer residence time) for easier quantification of interferences. Four mechanisms that generate artifacts and interferences were identified as follows: direct photolysis, foremost of HONO at a rate constant of 6% that of NO₂; thermal decomposition, primarily of PAN; surface promoted photochemistry; and secondary chemistry in the connecting tubing. These interferences are likely present to a certain degree in all photolytic converters currently in use but are rarely evaluated or reported. Recommendations for improved performance of photolytic converters include operating at lower cell pressure and higher flow rates, thermal management that ideally results in a match of photolysis cell temperature with ambient conditions, and minimization of connecting tubing length. When properly implemented, these interferences can be made negligibly small when measuring NO₂ in ambient air.

Implications: A new near-UV photolytic converter for measurement of the criteria pollutant nitrogen dioxide (NO₂) in ambient air by CL was characterized. Four mechanisms that generate interferences were identified and investigated experimentally: direct photolysis of HONO which occurred at a rate constant 6% that of NO₂, thermal decomposition of PAN and N₂O₅, surface promoted chemistry involving HNO₃, and secondary chemistry involving NO in the tubing connecting the converter and CL analyzer. These interferences are predicted to occur in all NO₂ P-CL systems but can be avoided by appropriate thermal management and operating at high flow rates.