Performance evaluation of Nahar oil–diesel blends in a single cylinder direct injection diesel engine

This study attempts to use plentiful available high oil content (67% of Nahar seed kernel) non-edible feedstock as a source for powering diesel engine. Various performance and emission characteristics of prepared Nahar oil–diesel blends (5%, 10%, 20%, 30%, and 40%) are analyzed in a single cylinder direct injection diesel engine at different load spectrum, in order to judge the optimum blend, which can be efficiently used in a diesel engine. 10% blending of Nahar oil with diesel fuel has shown a reduction in hydrocarbon and carbon monoxide emission by 8.64% and 8.34%, respectively. With the increase in blend concentration, the nitrogen oxide emission decreased considerably and smoke emission increased slightly. Further pressure crank angle and heat release rate analysis of 10% blending of Nahar oil with diesel confirms its smooth combustion inside the engine combustion chamber.     

Comparison of jatropha and karanja biofuels on their combustion characteristics

Biofuel blends produced from Jatropha (Jatropha curcas) and Karanja (Pongamia pinnata) oil were evaluated for their combustion properties. Two kinds of blends (regular diesel with Jatropha and Karanja oil) were prepared at 20% volume to the diesel and tested as alternative fuels in single cylinder (vertical), water-cooled, direct injection diesel engine at the rated speed of 1500 rpm. The performance of the engine in terms of thermal efficiency at full load for diesel was 30%. For Jatropha and Karanja biodiesel blends, the thermal efficiencies were 29.0% and 28.6%, respectively. The maximum cylinder pressure and ignition delay for biodiesel fuel blends are very close to that of regular diesel. Prolonged combustion was observed for Karanja oil blend in comparison to Jatropha oil blend. The combustion pattern also reveals the slow burning characteristics of vegetable oils and this study indicates that the blended biofuels have combustion characteristics that are similar to regular diesel fuels.     

Impact of various blends of Mimusops elengi methyl esters on performance and emission characteristics of a diesel engine

The basic objective of the research work was to study the effect of various blends of Mimusops elangi methyl ester (MEME) on engine performance, combustion, and emission characteristics of a single-cylinder direct-injection compression ignition engine, running at constant speed. The raw oil was extracted from Mimusops elangi seeds through mechanical crusher. The neat MEME was obtained through transesterification process and mixed with diesel in versatile proportions of 10% of MEME (10% MEME–90% Diesel), 20% of MEME(20% MEME–80% Diesel), 30% of MEME(30% MEME–70% Diesel), 40% of MEME(40% MEME–60% Diesel), and 100% MEME on a volume basis. Their properties were validated based on ASTM standards. Experimental investigation revealed that the 20% blend resulted in 4.18%, 5.12% more prominent performance characteristics of brake thermal efficiency, brake specific energy consumption, and superior emission diminution of 5.26% of HC, 16.6% of CO, 6.2% of smoke when compared with base diesel fuel, despite marginal penalty of 5.26% of carbon dioxide and 4.8% of oxides of nitrogen emission at full load condition. Characteristics of combustion parameters like pressure inside the cylinder and rate of the heat released were superior for 20% blend of MEME at the peak load condition.     

The effect of cerium oxide additive on the performance and emission characteristics of a CI engine operated with rice bran biodiesel and its blends

In this study, the rice bran oil (RBO) has been converted into methyl ester with an aid of transesterification reaction. Chemically, transesterification means conversion of triglyceride molecule or a complex fatty acid into alcohol and ester by removing the glycerin and neutralizing the free fatty acids. The B20 blend samples [80% diesel + 20% biodiesel] were prepared for each methyl ester obtained from RBO and then the cerium oxide (CeO₂) nanoparticles were added to the each B20 blend samples at a dosage of 50 ppm and 100 ppm with an aid of ultrasonicator. Moreover, in the absence of any engine modifications, the performance and emission characteristics of those blend samples have been investigated from the experimentally measured values such as density, viscosity, cloud point, pour point, and calorific value while the engine performance was also analyzed through the parameters like exhaust gas temperature (EGT), brake specific fuel consumption (BSFC), brake thermal efficiency (BTE), exhaust emission of carbon monoxide (CO), hydrocarbon (HC), and nitrogen oxide (NOx). The experimental results reveal that the use of CeO₂ blended biodiesel in diesel engine has exhibited good improvement in performance characteristic and reduction in exhaust emissions.     

Experimental investigation on the performance and emission characteristics of a diesel engine by varying the injection pressure and injection timing using mixed biodiesel

Biodiesel is a promising fuel for compression ignition engines instead of diesel fuel. Due to the depletion of diesel fuel, an alternative fuel can be used in an engine. The experiments were conducted on a four-stroke, single cylinder CI engine. In this present investigation, an attempt has been made to study the influence of injection pressure (IP) and injection timing (IT) on the performance and emission characteristics of diesel engines by using mixed biodiesel (Thevetia peruviana, Jatropha, Pongamia, and Azadirachta indica). The injection pressure is varied from 200 to 230 bar and the injection timing is varied from 23 to 29° bTDC at an increment of 10 bar and 2° bTDC, respectively, and the results were compared with diesel. From this study, the results showed that the brake thermal efficiency (BTE) was increased by 2.4% with an increase in injection pressure and 1.5% with an increase in the injection timing for the maximum load, but lesser than diesel. Furthermore, a reduction of 5.08% of brake specific fuel consumption (BSFC) has been noticed for the rise in IP and IT with loads but higher than diesel. The reduction was 34.17%, 53.85%, and 29.7% and 29.17%, 53.85%, and 21.95% of hydrocarbons (HC), carbon monoxide (CO), and smoke emissions, respectively, at 230 bar injection pressure and at 27° bTDC injection timing. Also, a significant increase in nitrogen oxides (NO_x) and carbon dioxide (CO₂) emissions at the maximum load was observed by increasing the injection pressure and injection timing.     

Effective application of ethanol in diesel engines

This work aimed to prove the effects of adding different proportions of ethanol with diesel (DE) and ethanol–water mixture with diesel (DEW) in a single-cylinder diesel engine on the performance, emissions, and combustion parameters. The blends were stabilized by tetra methyl ammonium bromide (TMAB) as the additive. The study was conducted at two operating conditions initially on a normal diesel engine and in the second case the engine piston, valves, and cylinder head coated with zirconia (ZrO₂) alumina (Al₂O₃). The results showed that the addition of 10% ethanol with diesel performed almost equivalent to neat diesel with 29.2% BTE and a 17.7% decrease in smoke and an 11.4% increase in NOx emission at peak load compared to that of the base fuel. Modified engines with thermal barrier coating (TBC) performed superior to normal engines with 4% and 5.5% increase in BTE, respectively, for DE- and DEW-type fuels with reduced exhaust emissions. A 5% addition of water with diesel–ethanol blends favors a higher proportion of ethanol to be employed in diesel engines.     

Combustion features under different center of heat release of a diesel engine using dimethyl carbonate/diesel blend

Experiments were performed in a single cylinder common-rail diesel engine that adopts a low temperature premixed charge compression ignition (PCCI) mode. Combustion features of dimethyl carbonate (DMC)-diesel blends under various centers of heat release (COHRs) were revealed in details. With retarding of COHR, all the peaks of pressure and pressure rise rate and bulk gas temperature are postponed and declined in sequence. Normally, the crank angle of peak pressure is quite close to the COHR, while the peak of bulk gas temperature appears about 7°CA after COHR as a rule. The prolongation can be demonstrated at every stage of combustion such as q₁₀ and q₉₀ with the COHR being put backward. In addition, the heat release of diesel is completely slower than that of D10 fuel at various stages. Unfortunately, retarding of COHR implies a declining thermal efficiency of engines as well as a higher cyclic variation in general. Nevertheless, D10 blend has higher thermal efficiency than diesel thanks to high oxygen content of DMC and low boiling point that prompts better fuel atomization and complete combustion. Meanwhile, the cyclical variation of D10 is greater than diesel fuel owing to the low heat value, high latent heat of vaporization, and poor flammability of DMC. As a total, a comprehensive understanding of PCCI combustion features under different COHRs can be conducive to conducting effective management of combustion process and manipulating the subsequent emission performance to a favorable level.     

An investigation of engine and fuel system performance in a diesel engine operating on waste cooking oil

Waste cooking oil (WCO) was experimentally examined to determine whether it can be used as an alternative fuel in a 3-cylinder, 4-stroke, direct injection, 48 kW power tractor engine. The test engine was operated under full load conditions using diesel fuel and waste vegetable oil from the 2400 to 1100 rpm and performance values were recorded. Tests were performed in two stages to evaluate the effect of the waste oils on the engine life cycle. When the test engine was operated with diesel fuel and waste cooking oil; engine torque decreased between at ratio of 0.09 % and 3% according to the engine speed. While no significant difference occurs in the diesel fuel tests at the end of 100 hours of operation, an important reduction was observed in the engine torque of the WCO engine between 4.21% and 14.48% according to the engine speed, and an increase in average smoke opacity ratio was also observed. In accordance with the results obtained from the studies, it was determined that the engine performance values of waste cooking oil show similar properties with diesel fuel, but in long-term usage, performance losses increased. In the SEM analysis performed on the fuel system, there were dark deposits at the nozzle tip and stem. According to an EDX analysis at the nozzle tips, the detected elements point to engine oil ash in the combustion chamber and show coking products (C and O). The other elements (Na, S, Ca, P, Cl, and K) point to used WCO.     

Emission study of a diesel engine fueled with higher alcohol-biodiesel blended fuels

This work examines the effect of butanol (higher alcohol) on the emission pattern of neat neem oil biodiesel (NBD100) fueled diesel engine. Single-cylinder, 4-stroke, research diesel engine was employed to conduct the trial. Blends comprising the mixture of biodiesel and higher alcohol were prepared by employing an ultrasonic agitator. Four test fuels such as neat neem oil biodiesel, diesel, and two blends of higher alcohol/neem oil biodiesel: 10% and 20% (by volume). Experimental result showed that increasing alcohol content to biodiesel brought down the various emissions such as Smoke, NO_x, HC, and CO by 6.8%, 10.4%, 8.6%, and 5.9%, respectively, at all loads. It was also concluded from the trail that a 20% higher alcohol/neem oil biodiesel blends show the promising signs in reducing all the emissions associated with biodiesel fuelled diesel engine.     

Investigation the effect of adding graphene oxide into diesel/higher alcohols blends on a diesel engine performance

ABSTRACT

This article aims to study the influence of the addition of graphene oxide nanoparticles (GO) to diesel/higher alcohols blends on the combustion, emission, and exergy parameters of a CI engine under various engine loads. The higher alcohols mainly n-butanol, n-heptanol, and n-octanol are blended with diesel at a volume fraction of 50%. Then, the 25 and 50 mg/L concentrations of GO are dispersed into diesel/higher alcohols blends using an ultrasonicator. The GO structures are examined using TEM, TGA, XRD and FTIR. The findings show that there is a reduction in p_max. and HRR when adding higher alcohols with diesel fuel. Regarding engine emission, there is a significant improvement in emissions formation with adding higher alcohols. The addition of GO into diesel/higher alcohols blends improves the brake thermal efficiency by 15%. Moreover, the p_max. and HRR are both enhanced by 4%. The CO, UHC and smoke formation are reduced considerably by 40%, 50 and 20%, respectively, while NO_x level is increased by 30% with adding GO. Finally, adding high percentages of n-butanol, n-heptanol, and n-octanol with diesel fuel with the presence of GO has the potential to achieve ultra-low CO, UHC, and smoke formation meanwhile keeping high thermal efficiency level.     

Usability of food industry waste oils as fuel for diesel engines

Two cogeneration units were each fitted with a prechamber (IDI) diesel engine in order to test the feasibility of using waste oils from the food industry as a fuel source, and additionally to test emissions generated by the combustion of these fuels. Esterified waste oils and animal fats as well as mustard oil were tested and compared to the more or less "common" fuels: diesel, rapeseed oil and rapeseed methyl ester. The results show that, in principle, each of these fuels is suitable for use in a prechamber diesel engine. Engine performance can be maintained at a constant level. Without catalytic conversion, the nitrogen oxides emissions were comparable. A significant reduction in NO(x) was achieved through the injection of urea. Combining a urea injection with the SCR catalytic converter reduced NO(x) emissions between 53% and 67%. The carbon monoxide emissions from waste oils are not significantly different from those of "common" fuels and can be reduced the same way as of hydrocarbon emissions, through utilization of a catalytic converter. The rate of carbon monoxide reduction by catalytic conversion was 84-86%. A lower hydrocarbon concentration was associated with fuels of agricultural origin. With the catalytic converter a reduction of 29-42% achieved. Each prechamber diesel engine exhibited its own characteristic exhaust, which was independent of fuel type. The selective catalytic reduction of the exhaust emissions can be realized without restriction using fuels of agricultural origin.     

对燃油征税的区域能源环境影响研究:以中国为例

控制汽柴油消费对中国的能源安全和环境保护有着重要意义.燃油税和碳税是中国近期两种主要的已经或可能施加于燃油的税收政策.以自回归分布滞后模型为核心,本研究构建了一个燃油税和碳税的区域能源环境影响评估模型.利用模型估计了我国的燃油需求价格弹性,测算了燃油需求响应,计算了在相同CO2减排目标下,提高汽油消费税、提高柴油消费税、引入碳税三种政策情景下各省份预计产生的节能效应、减排效应和税收效益.研究结果显示,在相同的CO2减排目标下,第一,在不同情景下,各省份节能程度差异均有限,但节能数量均体现出区域匹配性,燃油消费越多的省份,节能数量一般越多,且提高汽油消费税的全国节能总量最大;第二,在引入碳税情景下,各省份CO2减排比例差异最小;第三,在全国层面,三种政策情景中空气污染物(PM2.5和NOx和SO2)减排数量均为提高汽油消费税>引入碳税>提高柴油消费税,但在提高柴油消费税情景下,有4/5的省份预计PM2.5排放减少程度超过14%.除此之外,提高汽油消费税的税收收益最大.     

Experimental investigation on engine performances,combustion characteristics and emission of exhaust gases of VCR engine fuelled with cottonseed oil methyl ester blended with diesel

This research work investigates the engine performances, combustion characteristics, and emission of exhaust gases of variable compression ratio engine fuelled with cottonseed oil methyl ester (COME) and diesel at different blends. The analysis showed that heat release rate and cylinder pressure is higher for diesel than COME blends. Higher BTE is obtained at the maximum load condition. The higher BTE and lower SFC are obtained for blend B15 as 42.17% and 0.2 kg/kW-hr at brake mean effective pressure (BMEP) of 4.64 bar. Also it is found that the peak cylinder gas pressure and combustion duration increases when the BMEP increases. At the BMEP of 3.51 bar, higher HRR is observed as 18.12 J/deg. Increase in HRR is obtained as 6.07% for B30 at BMEP of 4.64 bar when compared to diesel. Ignition delay decreased by 13.16% for B100, by the increment of blend proportions when compared to diesel, at BMEP of 4.64 bar. Lower smoke, HC and CO emissions are observed when increasing the blend proportions, whereas the nitric oxide emissions increases due to the better combustion resulted in higher temperatures. At BMEP of 4.64 bar, the CO emissions are reduced to 25.24% for neat biodiesel when compared with the diesel.     

Scleropyrum pentandrum (Dennst.) mabb—oil as a feedstock for biodiesel production—engine performance and emission studies

A feasibility study on utilization of non edible oil of Scleropyrum pentandrum was carried out to see its potential as a new source for biodiesel production. Nonedible oil seeds of Scleropyrum pentandrum have oil content of 55–60%. Transesterification of freshly extracted oil in the presence of anhydrous sodium hydroxide at a concentration 1% (w/v oil) and methanol-oil ratio of 40% (v/v oil) yields 90.8% methyl esters under conventional heating. Month old oil requires sulfuric acid pretreatment (esterification) before transesterification. The transesterified oil has a density 889–893 kg/m³; kinematic viscosity of 4.21–5.7 mm²/s; cetane index 46.03; pour point of ?15°C and gross calorific value of 40.135 MJ/kg and oxidative stability of 2.35 hours. The properties are well within the Indian, European and American standard limits recommended for biodiesel except the oxidation stability, which can be improved by adding antioxidant additives. The engine performance studies of B10 and B20 blends of Scleropyrum pentandrum biodiesel (SP biodiesel) with statistical inference confirmed that it can be used as a fuel in CI engines without any engine modifications. The engine exhaust emission analysis showed that the emission of hydrocarbons can be minimized by at least 15–20%, CO emission by 15%, smoke opacity by 10–12% and moderately lesser CO₂ and NOx emissions.     

Performance of a diesel engine with water emulsified diesel prepared with optimized process parameters

An attempt has been made to produce stable water–diesel emulsion with optimal formulation and process parameters and to evaluate the performance and emission characteristics of diesel engine using this stable water–diesel emulsion. A total of 54 samples were prepared with varying water/diesel ratio, surfactant amount and stirring speed and water separation was recorded after 24 and 48 hr of emulsification. The recorded data were used in artificial neural network (ANN)-particle swarm optimization (PSO) technique to find the optimal parameters to produce water–diesel emulsion for engine testing. The predicted optimal parameters were found as 20% water to diesel ratio, 0.9% surfactant and 2200 rpm of stirrer for a water separation of 14.33% in one day with a variation of 6.54% against the actual value of water separation. Water–diesel emulsion fuel exhibited similar fuel properties as base fuel. The peak cylinder gas pressure, peak pressure rise rate and peak heat release rate for water–diesel were found higher as compared to diesel at medium to full engine loads. The improved air-fuel mixing in water–diesel emulsion enhanced brake thermal efficiency (BTE) of engine. The absorption of heat by water droplets present in water–diesel emulsion led to reduced exhaust gas temperature (EGT). With water–diesel emulsion fuel, the mean carbon monoxide (CO), unburned hydrocarbon and oxides of nitrogen (NO_x) emissions reduced by 8.80, 39.60, and 26.11%, respectively as compared to diesel.     

Investigation of Nanoparticle Additives to Biodiesel for Improvement of the Performance and Exhaust Emissions in a Compression Ignition Engine

Worldwide energy demand has been growing steadily during the past five decades and most experts believe that this trend will continue to rise. The amount of emitted harmful emission gases increases in parallel with increasing energy consumption. This increase has forced many countries to take various precautions, and various restrictions on emitted emissions have been carried. In this study, effects of addition of oxygen containing nanoparticle additives to biodiesel on fuel properties and effects on diesel engine performance and exhaust emissions were investigated. Two different nanoparticle additives, namely MgO and SiO₂, were added to biodiesel at the addition dosage of 25 and 50 ppm. Fuel properties, engine performance, and exhaust emission characteristics of obtained modified fuels were examined. As a result of this study, engine emission values NO_x and CO were decreased and engine performance values slightly increased with the addition of nanoparticle additives.     

Experimental investigations on direct injection diesel engines using grape seed oil methyl ester with different bowl geometries

In this paper, the performance of direct injection diesel engine was experimentally investigated under the influence of two different pistons’s geometry deep bowl combustion chamber (DBCC) and toroidal combustion chamber (TCC) compared with standard piston combustion chamber (SPCC) geometry. The experiments were carried out standard atmospheric conditions of 1.01325 bar and 30 ± 2 °C. The piston bowl was designed and developed without modifying the compression ratio of the engine. The investigations were carried out with B25 (25% GOME + 75% diesel), B50 (50% GOME + 50% diesel), B75 (75% GOME +25% diesel) and B100 (100% GOME) by volume blends for three different bowl geometries. The thermogravimetric analysis (TGA) was given the importance of higher in-cylinder temperature for the mass change of GOME leads to a more premixed phase of combustion. The results showed that DBCC has better combustion characteristics when compared with SPCC and TCC for all the blends. The B25 and B50 blends showed good combustion characteristics with DBCC and SPCC individually. While TCC showed average engine characteristics for all the blends categorically, the brake thermal efficiency for B25 blend confirmed a 4.7% higher than SPCC-diesel with DBCC piston, and the smoke, CO (Carbon monoxide), and HC (Hydrocarbon) are reduced by 9.2%, 30.7%, and 4.6%, respectively. Thus, the B25 blend in a DBCC piston engine was observed to be the distinction than other configurations. The results confirmed that the DBCC is a good option for B25 blend.     

Performance analysis of bioethanol (Water Hyacinth) on diesel engine

The increasing consumption and excessive extraction of conventional fuels is the matter of serious concern. Nowadays, world is looking for alternative sources of fuel which can partially replace conventional fuel dependence. The current investigation intends to provide evaluation of bio-ethanol preparation from Water Hyacinth (WH) and its influence on diesel engine performance under various operating conditions. This study explores the extraction of glucose from WH (Eichhornia crassipes) pretreated with sulfuric acid (H₂SO₄) for production of bio-ethanol. For the production of bio-ethanol different concentrations of H₂SO₄ acid hydrolysate (1%, 2%, 4%, 6%, 8%, and 10%) were prepared which was then followed by fermentation with cellulose fermenting yeasts. From results, it was observed that 4% H₂SO₄ acid hydrolysis produces higher concentrations of ethanol than other concentrations. Bio-ethanol extracted from WH was blended with diesel in different proportions (5%, 10%, 15%, 20%, and 25%) v/v and performance and emissions were experimentally investigated on single cylinder diesel engine under various load conditions. Experimental results show that 5 BED [5% bio-ethanol (WH + 95%diesel v/v) and 10BED (10% bio-ethanol (WH + 90%diesel v/v)] produces higher brake power, brake thermal efficiency and brake mean effective pressure with improved exhaust emission profiles than any other blend.     

Electrochemical NOx reduction and oxidation of HC and PM emissions from biodiesel fuelled diesel engines using electrochemically activated cell

NOx emission is produced during combustion of fuels at high temperature. Excessive release of NOx causes several effects on living organisms and environment. In this work, the efforts to reduce NOx emission by developing electrochemically activated cells (EACs) for a diesel engine fuelled with diesel and biodiesel fuel are discussed. EAC technique is vital after treatment technology attempted in this work to simultaneous control of NOx, HC, and PM emissions. In this method, two types of EACs were developed. The CuO–YSZ electrolyte and CuO–YSZ electrolyte with BaO coating were developed and tested with diesel and biodiesel exhaust. Compared with diesel fuel, use of biodiesel fuel increased NOx emission by 11% and PM emission was slightly reduced with biodiesel, which was due to the presence of fuel bond oxygen content in biodiesel. The investigation has demonstrated low-temperature activation of the EACs at 250–350°C which was due to the addition of CuO to YSZ. In this work, maximum NOx reduction was achieved for CuO–YSZ cells with BaO NOx storage and the simultaneous control of HC and PM emission also was observed in this technique. NOx reduction by EAC is a vital technique and can be retrofitted with any diesel engine for emission reduction.     

An experimental apparatus for testing biodiesels based on a CFR engine—setup and validation with different methyl ester blends

A cooperative fuel research (CFR) engine was modified and instrumented in order to control operating conditions and to measure engine parameters and in-cylinder pressure diagrams. Aiming at the comparison of different alternative fuels, an experimental procedure was defined, including cetane number (CN) evaluation and the definition of engine operating quantities in different working points, for fixed levels of compression ratio (CR) and injection advance. An investigation was made considering several blends of methyl-esters of rapeseed oil (RME) and of a mix of vegetable oils (VOME) with conventional diesel oil. The defined experimental procedure was applied to assess CN, engine brake thermal efficiency (bte) and exhaust emissions. Results show that the biodiesel content has a positive influence on soot emissions, with strong reduction, while thermal efficiency and NO_X emissions are negatively affected, which can be justified taking into account fuel properties and changes in combustion process. As observed outcomes are generally in line with those presented in literature, the facility proved to be a suitable tool for basic investigations on alternative fuels to be used in specific applications.