Influences of working pressure on properties for TiO2 films deposited by DC pulse magnetron sputtering

TiO2 films were deposited at room temperature by DC pulse magnetron sputtering system.The crystalline structures,morphological features and photocatalytic activity of TiO2 films were systematically investigated by X-ray diffraction (XRD),atomic force microscopy and ultraviolet spectrophotometer,respectively.The results indicated that the working pressure was the key deposition parameters influencing the TiO2 film phase composition at room temperature,which directly affected its photocatalytic activity.With increasing the working pressure,the target self-bias decreases monotonously.Therefore,low temperature TiO2 phase (anatase) could be deposited with high working pressure.The anatase TiO2 films deposited with 1.4 Pa working pressure displayed the highest photocatalytic activity by decomposition of Methyl Orange solution,which the degradation rate reached the maximum (35%) after irradiation by ultraviolet light for 1 h.     

不同煅烧温度制备TiO_2及光解2-氯苯甲酸

为了考察煅烧温度对TiO2结构和光催化活性的影响,以酞酸丁酯作为前驱体,利用溶胶-凝胶法在不同煅烧温度下制备TiO2,并用亚甲基蓝测试其光催化活性。TG热重分析表明,450~700℃时TiO2有晶型变化,XRD表征说明,TiO2晶型受煅烧温度影响显著,其中450~600℃煅烧制备的TiO2为锐钛矿型,650℃煅烧时TiO2出现金红石晶型;亚甲基蓝光解实验结果表明,煅烧温度显著影响TiO2的光催化活性,其中,450~600℃煅烧TiO2对亚甲基蓝光解效果较好,光降解2.5h后降解率高达95%~97%;550℃煅烧制备的锐钛矿型TiO2对2-氯苯甲酸有一定光解催化效果,紫外光解4h后降解率高达80%左右,光解过程符合零级动力学模式。     

TiO_2/Ti薄膜电极制备和光电催化降解罗丹明B的研究

以TA1钛合金为原料采用阳极氧化法制备新型薄膜电极 -TiO2 Ti电极 ,运用X射线衍射法、扫描电镜对电极表面膜的粒径、物相进行了表征。结果表明 ,控制反应条件 ,薄膜中二氧化钛晶型以锐钛矿型为主 ,粒径 45～ 5 0nm ,将其应用于光催化氧化水中的罗丹明B ,该电极对其降解有很好的光催化活性 ,同时 ,外加一定的偏压可以提高光催化氧化的效率     

Photocatalytic remediation of γ-HCH contaminated soil induced by α-Fe2O3 and TiO2

Heterogeneous photocatalytic degradation of γ-HCH on soil surfaces was carded out to evaluate the photocatalytic effectiveness of α-Fe2O3 and TiO2 toward degrading γ-HCH on soil surfaces. After being spiked with γ-HCH, soil samples were loaded with α-Fe2O3 or TiO2 and exposed to UV-light irradiation. Different catalyst loads, 0%, 2%, 5%, 7%, and 10% (wt.)α-Fe2O3 ; 0%, 0.5%, 1%, 2:(Wt.)TiO2, were tested for up to 7 d irradiation. The effects of soil thickness, acidity, and humic substances were also investigated. The obtained results indicated that the γ-HCH photodegradation follows the pseudo-first-order kinetics. The addition of α-Fe2O3 or TiO2 accelerates the photodegradation of γ-HCH, while the photodegradation rate decreases when the content of α-Fe2O3 exceeds 7% (wt.).The degradation rate increases with the soil pH value. Humic substances inhibit the photocatalytic degradation of γ-HCH., and trichlorobenzene are detected as photodegradation intermediates, which are gradually degraded with the photodegradation evolution.     

不同基质负载的TiO2薄膜光催化性能的比较

采用溶胶凝胶法制备出纳米TiO2粉末、ITO导电玻璃和普通玻璃负载的纳米TiO2薄膜光催化刺。通过对乙酸的降解实验表明：镀膜4次的TiO2／ITO薄膜的催化活性大约是TiO2／giass薄膜的2倍,与等负载量的TiO2粉末相比也具有较高的光催化活性。使用10次后,TiO2／ITO薄膜和TiO2／glass薄膜的光催化活性分别降低了25％和12％。但经再生后,催化活性可恢复至90％左右。     

Fe~(3+)掺杂TiO_2薄膜的制备及光催化降解甲醛的研究

采用溶胶-凝胶法制备Fe3+掺杂的TiO2薄膜光催化剂,进行甲醛的光催化实验,考察Fe3+掺杂量、薄膜焙烧温度及溶胶体系pH值对光催化性能的影响。结果表明,Fe3+掺杂量为1.0%,焙烧温度500℃1h,加硝酸溶胶体系pH=4时,Fe3+掺杂TiO2薄膜光催化活性最高。     

三氯乙烯在薄膜催化剂上的光催化降解动力学

研究了不同初始浓度三氯乙烯(TCE)在TiO₂薄膜催化剂上的光催化降解.结果表明,TCE在主波长为254nm的低压汞灯照射下易于发生光降解反应,而TiO₂薄膜催化剂能显著提高TCE的降解.光催化降解反应的伪一级速率常数随初始浓度的增加先升后降.在Langmuir-Hinshelwood方程基础上建立的光催化降解动力学模型包含了发生在薄膜催化剂表面的光催化氧化过程和发生的溶液体相的光降解过程,该动力学模型适用于表达低浓度有机物在薄膜催化剂上的光催化降解动力学.     

低量Gd~3+掺杂TiO_2粉体的制备及催化活性

利用溶胶-凝胶法在700℃制备了纯的和不同Gd3+掺杂量的TiO2纳米粉体,并用XRD技术对样品进行了表征。研究了Gd3+掺杂量对样品相结构、晶粒尺寸和光催化降解亚甲基蓝的活性的影响,利用相结构与纳米TiO2光催化活性关系探讨了Gd3+掺杂对纳米TiO2的光催化活性。结果表明,与纯TiO2相比,适量掺杂Gd3+可以显著提高其光催化活性。当Gd3+掺杂量为0.2%(质量),TiO2复合纳米粉体的光催化活性最佳,降解率为86%,其金红石相含量为15.4%,平均晶粒粒径为15nm;Gd3+掺杂强烈地抑制TiO2由锐钛矿相向金红石相的转变、减小晶粒尺寸和晶格膨胀程度这三方面均有利于提高光催化活性。     

Photocatalytic remediation of γ-HCH contaminated soil induced by α-Fe2O3 and TiO2

Heterogeneous photocatalytic degradation of γ-HCH on soil surfaces was carried out to evaluate the photocatalytic effectiveness of α-Fe2O3 and TiO2 toward degrading γ-HCH on soil surfaces. After being spiked with γ-HCH, soil samples were loaded with α-Fe2O3 or TiO2 and exposed to UV-light irradiation. Different catalyst loads(0%, 2%, 5%, 7%, and 10% (wt). α-Fe2O3; 0%, 0.5%, 1%, 2% wt. TiO2) were tested for up to 7 d irradiation. The effects of soil thickness, acidity, and humic substances were also investigated. The obtained results indicated that the γ-HCH photodegradation follows the pseudo-first-order kinetics. The addition of α-Fe2O3 or TiO2 accelerates the photodegradation of γ-HCH, while the photodegradation rate decreases when the content of α-Fe2O3 exceeds 7%(wt.). The degradation rate increases with the soil pH value. Humic substances inhibit the photocatalytic degradation of γ-HCH. Pentachlorocyclohexene, tetrachlorocyclohexene, and trichlorobenzene are detected as photodegradation intermediates, which are gradually degraded with the photodegradation evolution.     

Ag掺杂改性TiO_2催化降解水体中的邻苯二甲酸二甲酯

邻苯二甲酸酯是环境中普遍存在的有机污染物(内分泌干扰物)之一。通过湿式机械混合法制备Ag掺杂改性TiO2催化剂。光催化降解实验的结果表明Ag掺杂浓度为1×10-4mol/g,焙烧温度为400℃下所得的催化剂活性较好。对降解体系的研究表明,当催化剂的投加量为0.1~0.3 g/L、pH=5~8时降解效率较高(62.0%)。相对于催化剂的降解过程而言,其吸附作用是比较小的,而是以光催化反应为主。并利用荧光光谱对催化剂的性能进行了初步表征。     

Photocatalytic degradation of PCP-Na with TiO2 photocatalysis loaded with platinum

Titanium dioxide(TiO2) samples of different crystal forms were prepared by hydrolysis tetrbutyl titanate in various water to alkoxide ratios and sintering the hydrolysis product at different temperatures.The photocatalysts coated on hollow glass beads and loaded with platinum varying from 0.2% to 2.4% by weight.The photocatalytic degradation rate of sodium pentachlorophenolate (PCP-Na) depends on the preparing conditions such as:sintering temperatures,water to alkoxide ratios(R),platinum content and the size.The proper conditions of preparation photocatalysts are as follows:the ratio of tiO2:sodium silicate:hollow glass beads:platinum is 10:5:20:0.15(w/w),R is 100,sintering temperature is 650℃,and the size of hollow glass is 0.5-1mm.Under these conditions,the ratio between acatase and rutile of the photocatalyst is 2:1,and the photocatalytic activity is high.     

纳米掺氮TiO_2可见光降解环境内分泌干扰物BPA研究

用水湿法得到掺氮TiO2前体,热处理后得到掺氮TiO2粉体,用XRD和UV-Vis吸收光谱等手段对制备的掺氮TiO2进行了表征,并研究了N-TiO2可见光光催化降解环境内分泌干扰物双酚A。结果表明掺氮TiO2在400℃下煅烧1h,所得粉体是锐钛矿相结构,粒径约12nm,与纯TiO2相比,吸收边明显红移。催化剂掺氮TiO2具有可见光催化活性,且明显高于纯TiO2。在双酚A初始浓度为40mg/L,催化剂掺氮TiO2的煅烧温度为400℃,投加量为0.6g/L,pH=5的条件下的降解效果最好达48.91%。     

混晶纳米TiO_2的制备及其光催化降解有毒有机污染物

以无定形TiO2沉淀为前驱体,在水热条件下得到了含板钛矿(121)相混晶纳米TiO2,考察了水热反应的温度和时间等因素对含板钛矿型TiO2光催化活性的影响.采用XRD、TEM对制备的TiO2进行初步表征,并结合光催化(λ≤387 nm)降解有机染料的光活性探针反应.结果表明,水热温度为150℃,时间为24 h时,可制得具有较高光催化活性的纳米TiO2,其纳米尺寸为14.20 nm,板钛矿相含量63.6%,锐钛矿含量为36.4%.光催化实验中跟踪研究了其对染料酸性桃红(sulforhodmineB,SRB)的褪色及2,4-DCP的降解情况,并对降解中间产物H2 O2、.OH进行跟踪测定,实验结果表明板钛矿相混晶TiO2的光催化主要涉及.OH氧化历程,光照射9 h对SRB和2,4-DCP的矿化氧化分别达到89%和78%,循环5次光催化降解SRB实验,催化剂表现出较好的稳定性,催化性能无明显变化.     

硼掺杂CeO2/TiO2光催化剂的制备及其活性研究

在三氯化钛和钛酸丁酯水解过程中引入硼酸、硝酸铈,制备了具有可见光活性的硼(B)掺杂CeO₂/TiO₂复合氧化物光催化剂,采用XRD、DRS、XPS等手段进行表征,以偶氮染料酸性红B为模型污染物评估了催化活性.结果表明,硝酸铈加入量影响催化剂的吸收带边,随用量增加,吸收带边红移至481nm(Ce/Ti=1.0,摩尔比),继续增加用量,吸收带边轻微蓝移.催化剂晶相组成与焙烧温度有关,500℃时焙烧样品主要由立方晶型CeO₂和锐钛矿TiO₂组成,焙烧温度高于700℃时,TiO₂转化为金红石型,CeO₂则无显著变化.随焙烧温度升高,催化剂吸收带边明显蓝移,综合考虑催化剂稳定性和太阳能利用,认为500℃焙烧较为合适.B1s XPS显示仅有少量B原子进入复合氧化物晶格取代了氧原子,主要以B₂O₃形式存在.酸性红B降解试验显示B掺杂CeO₂/TiO₂可以提高TiO₂的催化活性,紫外光辐射10min最高可使96.0%的酸性红B分解,且反应彻底,表现出较强的氧化能力,但Ce/Ti>0.5(摩尔比)时催化活性显著下降.     

Fe^3＋掺杂TiO2纳米膜的制备及光催化性能的研究

采用溶胶-凝胶法制备出掺杂Fe^3＋的TiO2纳米膜,并用x射线衍射方法进行表征;探讨了金属离子铁离子掺杂对TiO2纳米膜光催化降解性能的影响;研究了TiO2纳米膜及掺杂改性的TiO2纳米膜对甲基兰的降解作用,同时还尝试不同掺杂的TiO2纳米膜的杀菌功能。实验结果表明通过掺杂Fe的TiO2纳米膜有优良的光催化降解性能。     

Photoelectrocatalytic degradation of Rose Bengal

An innovative photoelectrode, TiO2/T1 mesh electrode, was prepared by galvanostaticanodisation. The morphology and the crystalline texture of the TiO2 film on mesh electrode were examined by scanning electronic microscopy and Raman spectroscopy respectively. The examination results indicated that the structure and properties of the film depended on anodisation rate, and the anatase was the dominant component under the controlled experimental conditions. Degradation of Rose Bengal (RB) in photocatalytic (PC) and photoelectrocatalytic (PEC) reaction was investigated, the results demonstrated that electric biasing could improve the efficiency of photecatalytic reaction. The measurement results of TOC in photoelectrocatalytic degradation showed that the mineralisation of RB was complete relatively. The comparison between the degradation efficiency of RB in PEC process and that in aqueous TiO2 dispersion was conducted. The results showed that the apparent first-order rate constant of RB degradation in PEC process was larger than that in aqueous dispersion with 0.1%--0.3% TiO2 powder, but was smaller than that in aaueaus disverslon with 1.0% TiO2.     

Enhancement of formaldehyde degradation by amine functionalized silica/titania films

Doping amine functional groups into SiO2/TiO2 films for enhancing the decomposition of formaldehyde has been investigated using the modified sol-gel method to prepare organic-inorganic hybrid photocatalysts via the co-condensation reaction of methyltrimethoxysilane (MTMOS) and amine functional groups. n-(2-Aminoethyl)-3-aminopropyl-trimethoxysilane (AEAPTMS) and 3-aminopropyl-trimethoxysilane (APTMS) were selected to study the e ect of amine functional groups on the enhancement of formaldehyde adsorption and degradation under a UV irradiation process. Physicochemical properties of prepared photocatalysts were characterized with nitrogen adsorption-desorption isotherms measurement, X-ray di raction (XRD) and Fourier transform infrared (FT-IR) spectroscopy. The results indicated that the APTMS/SiO2/TiO2 film demonstrated a degradation e ciency of 79% superior to those of SiO2/TiO2 and AEAPTMS/SiO2/TiO2 films due to the synergetic e ect of adsorption and photocatalytic properties. The APTMS/SiO2/TiO2 film can be recycled with about 7% decreasing of degradation e ciency after seven cycles.     

碳黑改性TiO2薄膜光催化剂的结构性质

通过碳黑掺杂制备了改性的TiO₂薄膜光催化剂(CB-TiO₂),并采用液氮吸附、X射线衍射(XRD)和紫外-可见光漫反射光谱(DRS)对催化剂的比表面积、物相、晶粒度和最大激发波长等结构性质进行了表征.结果表明,CB-TiO₂的吸附性能大大改善,不同热处理温度下,BET比表面积增加50%～80%;同时碳黑掺杂能够减小催化剂的晶粒尺度,使相变温度降低.相应的光催化降解试验也表明,碳黑改性TiO₂的活性大大提高,其一级反应速率常数为普通TiO₂的1.5倍.     

邻-氯酚在TiO_2膜上光催化降解及反应动力学特征

以钛酸四丁酯为原料采用Sol Gel法制备了玻璃负载TiO2 膜光催化剂 ,应用XRD表征了不同实验条件下薄膜中TiO2 的晶相结构和粒度。分析了不同层数TiO2 膜的光催化活性和溶液 pH值对邻 氯酚 (2 CP)的影响。结果表明 :处理温度为 50 0℃时不同厚度薄膜中TiO2 均为锐钛矿晶型 ,粒径 8～ 33nm ,5层涂膜光催化活性最高。在高 pH值和低pH值区域 2 CP ,在TiO2 膜上的光催化降解速率较大。 2 CP初始浓度 (C0 )与反应速率 (r0 )的关系符合Langmuir Hinshelwood方程 ,当C0 ≤ 0 .6mmol·L- 1 时 ,降解反应可用一级动力学模式来描述。     

TiO_2薄膜光催化降解邻苯二甲酸乙酯的研究

采用solgel法制备TiO2薄膜。以该薄膜为催化剂,研究了在H2O2存在的条件下,对内分泌干扰物质邻苯二甲酸乙酯(DEP)的光催化降解反应。分别讨论了pH值、H2O2的加入量、DEP的初始浓度以及光照时间对降解反应的影响。结果表明在pH=2、50mg/L的H2O2中对初始浓度为50mg/L的DEP溶液光照150min有较好的降解效果。