Bioremediation of acidic oily sludge-contaminated soil by the novel yeast strain Candida digboiensis TERI ASN6

Background, aim, and scope

Primitive wax refining techniques had resulted in almost 50,000 tonnes of acidic oily sludge (pH 1–3) being accumulated inside the Digboi refinery premises in Assam state, northeast India. A novel yeast species Candida digboiensis TERI ASN6 was obtained that could degrade the acidic petroleum hydrocarbons at pH 3 under laboratory conditions. The aim of this study was to evaluate the degradation potential of this strain under laboratory and field conditions.

Materials and methods

The ability of TERI ASN6 to degrade the hydrocarbons found in the acidic oily sludge was established by gravimetry and gas chromatography–mass spectroscopy. Following this, a feasibility study was done, on site, to study various treatments for the remediation of the acidic sludge. Among the treatments, the application of C. digboiensis TERI ASN6 with nutrients showed the highest degradation of the acidic oily sludge. This treatment was then selected for the full-scale bioremediation study conducted on site, inside the refinery premises.

Results

The novel yeast strain TERI ASN6 could degrade 40 mg of eicosane in 50 ml of minimal salts medium in 10 days and 72% of heneicosane in 192 h at pH 3. The degradation of alkanes yielded monocarboxylic acid intermediates while the polycyclic aromatic hydrocarbon pyrene found in the acidic oily sludge yielded the oxygenated intermediate pyrenol. In the feasibility study, the application of TERI ASN6 with nutrients showed a reduction of solvent extractable total petroleum hydrocarbon (TPH) from 160 to 28.81 g kg^?1 soil as compared to a TPH reduction from 183.85 to 151.10 g kg^?1 soil in the untreated control in 135 days. The full-scale bioremediation study in a 3,280-m² area in the refinery showed a reduction of TPH from 184.06 to 7.96 g kg^?1 soil in 175 days.

Discussion

Degradation of petroleum hydrocarbons by microbes is a well-known phenomenon, but most microbes are unable to withstand the low pH conditions found in Digboi refinery. The strain C. digboiensis could efficiently degrade the acidic oily sludge on site because of its robust nature, probably acquired by prolonged exposure to the contaminants.

Conclusions

This study establishes the potential of novel yeast strain to bioremediate hydrocarbons at low pH under field conditions.

Recommendations and perspectives

Acidic oily sludge is a potential environmental hazard. The components of the oily sludge are toxic and carcinogenic, and the acidity of the sludge further increases this problem. These results establish that the novel yeast strain C. digboiensis was able to degrade hydrocarbons at low pH and can therefore be used for bioremediating soils that have been contaminated by acidic hydrocarbon wastes generated by other methods as well.     

Natural deep eutectic solvent mediated pretreatment of rice straw: bioanalytical characterization of lignin extract and enzymatic hydrolysis of pretreated biomass residue

The present investigation demonstrated pretreatment of lignocellulosic biomass rice straw using natural deep eutectic solvents (NADESs), and separation of high-quality lignin and holocellulose in a single step. Qualitative analysis of the NADES extract showed that the extracted lignin was of high purity (>90 %), and quantitative analysis showed that nearly 60?±?5 % (w/w) of total lignin was separated from the lignocellulosic biomass. Addition of 5.0 % (v/v) water during pretreatment significantly enhanced the total lignin extraction, and nearly 22?±?3 % more lignin was released from the residual biomass into the NADES extract. X-ray diffraction studies of the untreated and pretreated rice straw biomass showed that the crystallinity index ratio was marginally decreased from 46.4 to 44.3 %, indicating subtle structural alterations in the crystalline and amorphous regions of the cellulosic fractions. Thermogravimetric analysis of the pretreated biomass residue revealed a slightly higher T _dcp (295 °C) compared to the T _dcp (285 °C) of untreated biomass. Among the tested NADES reagents, lactic acid/choline chloride at molar ratio of 5:1 extracted maximum lignin of 68?±?4 mg g^?1 from the rice straw biomass, and subsequent enzymatic hydrolysis of the residual holocellulose enriched biomass showed maximum reducing sugars of 333?±?11 mg g^?1 with a saccharification efficiency of 36.0?±?3.2 % in 24 h at 10 % solids loading.     

Kinetics of phenol biodegradation at high concentration by a metabolically versatile isolated yeast Candida tropicalis PHB5

A highly tolerant phenol-degrading yeast strain PHB5 was isolated from wastewater effluent of a coke oven plant and identified as Candida tropicalis based on phylogenetic analysis. Biodegradation experiments with C. tropicalis PHB5 showed that the strain was able to utilize 99.4 % of 2,400 mg l^?1 phenol as sole source of carbon and energy within 48 h. Strain PHB5 was also observed to grow on 18 various aromatic hydrocarbons. Haldane model was used to fit the exponential growth data and the following kinetic parameters were obtained: μ _max?=?0.3407 h^?1, K _S?=?15.81 mg l^?1, K _i?=?169.0 mg l^?1 (R ²?=?0.9886). The true specific growth rate, calculated from μ _max, was 0.2113. A volumetric phenol degradation rate (V _max) was calculated by fitting the phenol consumption data with Gompertz model and specific degradation rate (q) was calculated from V _max. The q values were fitted with Haldane model, yielding following parameters: q _max?=?0.2766 g g^?1 h^?1, K _S ′?=?2.819 mg l^?1, K _i ′?=?2,093 (R ²?=?0.8176). The yield factor (Y _X/S ) varied between 0.185 to 0.96 g g^?1 for different initial phenol concentrations. Phenol degradation by the strain proceeded through a pathway involving production of intermediates such as catechol and cis,cis-muconic acid which were identified by enzymatic assays and HPLC analysis.     

Distribution of potentially toxic elements (PTEs) in tailings,soils, and plants around Gol-E-Gohar iron mine,a case study in Iran

This study investigated the concentration of potentially toxic elements (PTEs) including Al, As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Mo, Ni, Pb, Sb, V, and Zn in 102 soils (in the Near and Far areas of the mine), 7 tailings, and 60 plant samples (shoots and roots of Artemisia sieberi and Zygophylum species) collected at the Gol-E-Gohar iron ore mine in Iran. The elemental concentrations in tailings and soil samples (in Near and Far areas) varied between 7.4 and 35.8 mg kg^?1 for As (with a mean of 25.39 mg kg^?1 for tailings), 7.9 and 261.5 mg kg^?1 (mean 189.83 mg kg^?1 for tailings) for Co, 17.7 and 885.03 mg kg^?1 (mean 472.77 mg kg^?1 for tailings) for Cu, 12,500 and 400,000 mg kg^?1 (mean 120,642.86 mg kg^?1 for tailings) for Fe, and 28.1 and 278.1 mg kg^?1 (mean 150.29 mg kg^?1 for tailings) for Ni. A number of physicochemical parameters and pollution index for soils were determined around the mine. Sequential extractions of tailings and soil samples indicated that Fe, Cr, and Co were the least mobile and that Mn, Zn, Cu, and As were potentially available for plants uptake. Similar to soil, the concentration of Al, As, Co, Cr, Cu, Fe, Mn, Mo, Ni, and Zn in plant samples decreased with the distance from the mining/processing areas. Data on plants showed that metal concentrations in shoots usually exceeded those in roots and varied significantly between the two investigated species (Artemisia sieberi > Zygophylum). All the reported results suggest that the soil and plants near the iron ore mine are contaminated with PTEs and that they can be potentially dispersed in the environment via aerosol transport and deposition.     

Utilization of water chestnut for reclamation of water environment and control of cyanobacterial blooms

Overgrowth of water chestnut (Trapa spp.) is a regional problem throughout Asia and North America because of waterway blockage and water fouling upon decomposition. In the present study, we investigated the potential of water chestnut to control cyanobacterial blooms, via a high content of phenolic compounds. In addition, we assessed the impact of biomass harvesting and crude extract application on nutrient balance. We showed that the floating parts of water chestnut contained high concentrations of total phenolics (89.2 mg g^?1 dry weight) and exhibited strong antioxidant activity (1.31 mmol g^?1 dry weight). Methanol-extracted phenolics inhibited growth of Microcystis aeruginosa; the half maximal effective concentration (EC₅₀) of the extracted phenolics was 5.8 mg L^?1, which was obtained from only 103 mg L^?1 of dry biomass (the floating and submerged parts). However, the crude extracts also added important quantities of nitrogen, phosphorus, and potassium (1.49, 1.05, and 16.3 mg g^?1, respectively; extracted dry biomass weight basis); therefore, in practice, nutrient removal before and/or after the extraction is essential. On the other hand, biomass harvesting enables recovery of nitrogen, phosphorus, and potassium from the water environment (23.1, 2.9, and 18.7 mg g^?1, respectively; dry biomass weight basis). Our findings indicate that water chestnut contains high concentrations of phenolics and exhibits strong antioxidant activity. Utilization of these resources, including nutrients, will contribute to reclamation of the water environment, and also to disposal of wet biomass.     

Copper bioaccumulation,photosystem II functioning,and oxidative stress in the seagrass <Emphasis Type="Italic">Cymodocea nodosa</Emphasis> exposed to copper oxide nanoparticles

Photosynthetic activity, oxidative stress, and Cu bioaccumulation in the seagrass Cymodocea nodosa were assessed 4, 12, 24, 48, and 72 h after exposure to two copper oxide nanoparticle (CuO NP) concentrations (5 and 10 mg L^?1). CuO NPs were characterized by scanning electron microscopy (SEM) and dynamic light scattering measurements (DLS). Chlorophyll fluorescence analysis was applied to detect photosystem II (PSII) functionality, while the Cu accumulation kinetics into the leaf blades was fitted to the Michaelis-Menten equation. The uptake kinetics was rapid during the first 4 h of exposure and reached an equilibrium state after 10 h exposure to 10 mg L^?1 and after 27 h to 5 mg L^?1 CuO NPs. As a result, 4-h treatment with 5 mg L^?1 CuO NPs, decreased the quantum yield of PS II photochemistry (Φ _PSΙΙ ) with a parallel increase in the regulated non-photochemical energy loss in PSII (Φ _NPQ ). However, the photoprotective dissipation of excess absorbed light energy as heat, through the process of non-photochemical quenching (NPQ), did not maintain the same fraction of open reaction centers (q _p ) as in control plants. This reduced number of open reaction centers resulted in a significant increase of H₂O₂ production in the leaf veins serving possibly as an antioxidant defense signal. Twenty-four-hour treatment had no significant effect on Φ _PSΙΙ and q _p compared to controls. However, 24 h exposure to 5 mg L^?1 CuO NPs increased the quantum yield of non-regulated energy loss in PSII (Φ _NO ), and thus the formation of singlet oxygen (¹O₂) via the triplet state of chlorophyll, possible because the uptake kinetics had not yet reached the equilibrium state as did 10 mg L^?1. Longer-duration treatment (48 and 72 h) had less effect on the allocation of absorbed light energy at PSII and the fraction of open reaction centers, compared to 4-h treatment, suggesting the function of a stress defense mechanism. The response of C. nodosa leaves to CuO NPs fits the “Threshold for Tolerance Model” with a threshold time (more than 4 h) required for induction of a stress defense mechanism, through H₂O₂ production.     

Stormwater harvesting from landscaped areas: effect of herbicide application on water quality and usage

The suitability of stormwater harvested from pervious pavement system (PPS) structures for reuse purposes was investigated in conditions where glyphosate-containing herbicides (GCH) are applied as part of PPS maintenance procedure. The experiment was based on the four-layered design previously described as detailed in CIRIA C582. Results indicated that the highest sodium absorption ratio (SAR) of 1.6 recorded in this study, was less than that at which loss of permeability begins to occur as well as deterioration of matrix structure. Furthermore, the maximum electrical conductivity (ECw) of 2990 μS cm^?1, recorded for 7200 mg L^?1 concentration (GCH) was slightly below the unstable classification range at which salinity problems related to water quality occur such that salts accumulate in the root zone to the extent that crop yields are adversely affected. However, GCH concentration of 720 mg L^?1 was within ‘permissible’ range while that of 72 mg L^?1 was within ‘excellent’ range. Current study raises some environmental concerns owing to the overall impact that GCH at concentrations above 72 mg L^?1 exerts on the net performance of the organic decomposers, heavy metal and hydrocarbon release from the system and thus, should be further investigated. However, effluent from all the test models including those dosed with high GCH concentration of 7200 mg L^?1 do not pose any threat in terms of infiltration or deterioration associated with salinity although, there are indications that high dosage of the herbicide could lead to an elevated electrical conductivity of the recycled water.

Open image in new window

Graphical abstract Impact of herbicide on irrigation water quality

     

Evaluation of Acinetobacter sp. B9 for Cr (VI) resistance and detoxification with potential application in bioremediation of heavy-metals-rich industrial wastewater

Present work demonstrates Cr (VI) detoxification and resistance mechanism of a newly isolated strain (B9) of Acinetobacter sp. Bioremediation potential of the strain B9 is shown by simultaneous removal of major heavy metals including chromium from heavy-metals-rich metal finishing industrial wastewater. Strain B9 tolerate up to 350 mg L^?1 of Cr (VI) and also shows level of tolerance to Ni (II), Zn (II), Pb (II), and Cd (II). The strain was capable of reducing 67 % of initial 7.0 mg L^?1 of Cr (VI) within 24 h of incubation, while in presence of Cu ions 100 % removal of initial 7.0 and 10 mg L^?1 of Cr (VI) was observed with in 24 h. pH in the range of 6.0–8.0 and inoculum size of 2 % (v/v) were determined to be optimum for dichromate reduction. Fourier transform infrared spectroscopy and transmission electron microscopy studies suggested absorption or intracellular accumulation and that might be one of the major mechanisms behind the chromium resistance by strain B9. Scanning electron microscopy showed morphological changes in the strain due to chromium stress. Relevance of the strain for treatment of heavy-metals-rich industrial wastewater resulted in 93.7, 55.4, and 68.94 % removal of initial 30 mg L^?1 Cr (VI), 246 mg L^?1 total Cr, and 51 mg L^?1 Ni, respectively, after 144 h of treatment in a batch mode.     

Ecotoxicological effects on the earthworm Eisenia fetida following exposure to soil contaminated with imidacloprid

Imidacloprid, a neonicotinoid insecticide, has been used widely in agriculture worldwide. The adverse effects of imidacloprid on exposed biota have brought it increasing attention. However, knowledge about the effects of imidacloprid on antioxidant defense systems and digestive systems in the earthworm is vague and not comprehensive. In the present study, the changes in the activity of superoxide dismutase (SOD), catalase (CAT), peroxidase (POD), cellulase, reactive oxygen species (ROS), and malondialdehyde (MDA) in the earthworm Eisenia fetida exposed to artificial soil treated with imidacloprid were examined systematically. The results showed that the activity of these biomarkers was closely related to the dose and duration of the exposure to imidacloprid. The activity of SOD was stimulated significantly at doses of 0.66 and 2 mg kg^?1 imidacloprid but markedly inhibited at a dose of 4 mg kg^?1 imidacloprid with prolonged exposure. The activities of CAT and POD increased irregularly at 0.2–4 mg kg^?1 imidacloprid over different exposure times. The level of ROS at a dose of 2 or 4 mg kg^?1 imidacloprid was significantly increased over the entire exposure period. When the concentration of imidacloprid was above 0.66 mg kg^?1, the balance of the activity of the antioxidant enzymes and ROS level was interrupted. The activity of cellulase decreased significantly with prolonged exposure. At the stress of 4 mg kg^?1 imidacloprid, the content of MDA was significantly increased with increasing exposure time. The results of the present study suggest that imidacloprid has a potentially harmful effect on E. fetida and may be helpful for assessment of the risk of imidacloprid to the soil ecosystem environment. However, to obtain more comprehensive toxicity data, it is necessary to investigate the effects of imidacloprid on earthworm using native soils in the future work.     

Phytoscreening and phytoextraction of heavy metals at Danish polluted sites using willow and poplar trees

The main purpose of this study was to determine typical concentrations of heavy metals (HM) in wood from willows and poplars, in order to test the feasibility of phytoscreening and phytoextraction of HM. Samples were taken from one strongly, one moderately, and one slightly polluted site and from three reference sites. Wood from both tree species had similar background concentrations at 0.5 mg kg^?1 for cadmium (Cd), 1.6 mg kg^?1 for copper (Cu), 0.3 mg kg^?1 for nickel (Ni), and 25 mg kg^?1 for zinc (Zn). Concentrations of chromium (Cr) and lead (Pb) were below or close to detection limit. Concentrations in wood from the highly polluted site were significantly elevated, compared to references, in particular for willow. The conclusion from these results is that tree coring could be used successfully to identify strongly heavy metal-polluted soil for Cd, Cu, Ni, Zn, and that willow trees were superior to poplars, except when screening for Ni. Phytoextraction of HMs was quantified from measured concentration in wood at the most polluted site. Extraction efficiencies were best for willows and Cd, but below 0.5 % over 10 years, and below 1?‰ in 10 years for all other HMs.     

Novel chitosan/PVA/zerovalent iron biopolymeric nanofibers with enhanced arsenic removal applications

Enhanced removal application of both forms of inorganic arsenic from arsenic-contaminated aquifers at near-neutral pH was studied using a novel electrospun chitosan/PVA/zerovalent iron (CPZ) nanofibrous mat. CPZ was carefully examined using scanning electron microscopy (SEM) equipped with energy-dispersive X-ray analysis (EDX), transmission electron microscopy (TEM), atomic fluorescence spectroscopy (AFM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), and thermal gravimetric analysis (TGA). Application of the adsorbent towards the removal of total inorganic arsenic in batch mode has also been studied. A suitable mechanism for the adsorption has also been discussed. CPZ nanofibers mat was found capable to remove 200.0?±?10.0 mg g^?1 of As(V) and 142.9?±?7.2 mg g^?1 of As(III) from aqueous solution of pH 7.0 at ambient condition. Addition of ethylenediaminetetraacetic acid (EDTA) enabled the stability of iron in zerovalent state (ZVI). Enhanced capacity of the fibrous mat could be attributed to the high surface area of the fibers, presence of ZVI, and presence of functional groups such as amino, carboxyl, and hydroxyl groups of the chitosan and EDTA. Both Langmuir and Freundlich adsorption isotherms were applicable to describe the removal process. The possible mechanism of adsorption has been explained in terms of electrostatic attraction between the protonated amino groups of chitosan/arsenate ions and oxidation of arsenite to arsenate by Fentons generated from ZVI and subsequent complexation of the arsenate with the oxidized iron. These CPZ nanofibrous mats has been prepared with environmentally benign naturally occurring biodegradable biopolymer chitosan, which offers unique advantage in the removal of arsenic from contaminated groundwater.     

Human health risk from organ-specific accumulation of toxic metals and response of antioxidants in edible fish species from Chenab River,Pakistan

In the current study, the bioaccumulation of essential and nonessential metals and related antioxidant activity were analyzed in three organs (muscle, gills, and liver) of herbivorous (HF) and carnivorous (CF) edible fish of Chenab River. The comparative analysis revealed a more heterogeneous accumulation of metals in the muscles of HF fish than that of CF fish [chromium (Cr, 3.4 μg g^?1), cobalt (Co, 1.7 μg g^?1), copper (Cu, 3 μg g^?1), and iron (Fe, 45 μg g^?1) versus Cr (1.3 μg g^?1), Co (0.1 μg g^?1), Cu (1.1 μg g^?1), and Fe (33 μg g^?1), respectively, P?<?0.001]. These results implied an organ-specific accumulation of metals at different trophic levels. According to logistic regression analysis, the bioaccumulation of metals had marked differences in HF and CF. The antioxidant activity was significantly related to the tissue type and the metals to which the organs are exposed to. The liver of CF fish had a higher activity of antioxidant superoxide dismutase (SOD), catalase (CAT), glutathione (GSH), and lipid peroxidase (LPO) than that of HF (P?<?0.05). LPO and guaiacol peroxidase (POD) in both groups were associated with a number of metals, but in HF, cadmium (Cd), Cr, Pb, and Zn were more related with the LPO and SOD activities. Moreover, Cd, Co, Fe, Pb, Ni, Cu, and Zn were above the permissible limits set by various agencies. In numerous cases, our results were even higher than those previously reported in the literature. The results provide an insight into the pollution pattern of Chenab River. These results may be helpful in the future to identify biomarkers of exposure in aquatic organisms.

Accumulation of Cr,Cd, Pb,Cu, and Zn by plants in tanning sludge storage sites: opportunities for contamination bioindication and phytoremediation

Tanning sludge enriched with high concentrations of Cr and other metals has adverse effects on the environment. Plants growing in the metalliferous soils may have the ability to cope with high metal concentrations. This study focuses on potentials of using native plants for bioindication and/or phytoremediation of Cr-contaminated sites. In the study, we characterized plants and soils from six tanning sludge storage sites. Soil in these sites exhibited toxic levels of Cr (averaged 16,492 mg kg^?1) and other metals (e.g., 48.3 mg Cu kg^?1, 2370 mg Zn kg^?1, 44.9 mg Pb kg^?1, and 0.59 mg Cd kg^?1). Different metal tolerance and accumulation patterns were observed among the sampled plant species. Phragmites australis, Zephyranthes candida, Cynodon dactylon, and Alternanthera philoxeroides accumulated moderate-high concentrations of Cr and other metals, which could make them good bioindicators of heavy metal pollution. High Cr and other metal concentrations (e.g., Cd and Pb) were found in Chenopodium rubrum (372 mg Cr kg^?1), Aster subulatus (310 mg Cr kg^?1), and Brassica chinensis (300 mg Cr kg^?1), being considered as metal accumulators. In addition, Nerium indicum and Z. candida were able to tolerate high concentrations of Cr and other metals, and they may be used as preferable pioneer species to grow or use for restoration in Cr-contaminated sites. This study can be useful for establishing guidelines to select the most suitable plant species to revegetate and remediate metals in tanning sludge-contaminated fields.     

Cadmium-tolerant bacteria induce metal stress tolerance in cereals

Cadmium usually hampers plant growth, but bacterial inoculation may improve stress tolerance in plants to Cd by involving various mechanisms. The objective was to characterize and identify bacteria that improve plant growth under Cd stress and reduce Cd uptake. Cadmium-tolerant bacteria were isolated from rhizosphere soil, which was irrigated with tannery effluent, and six strains were selected as highly tolerant to Cd, showing minimum inhibitory concentration as 500 mg L^?1 or 4.45 mmol L^?1. These strains were identified by 16S rRNA gene analysis and functional analysis in regard to plant growth promotion characteristics. To determine their effect on cereal growth under Cd stress, seeds were inoculated with these strains individually and grown in soil contaminated with three Cd levels (0, 40 and 80 mg kg^?1). Biomass production, relative water content (RWC), electrolyte leakage (ELL) and tissue Cd concentration were measured. Biomass of both cereals was inhibited strongly when exposed to Cd; however, bacterial inoculation significantly reduced the suppressive effect of Cd on cereal growth and physiology. The bacterial isolates belonged to the genera Klebsiella, Stenotrophomonas, Bacillus and Serratia. Maize was more sensitive than wheat to Cd. Klebsiella sp. strain CIK-502 had the most pronounced effects in promoting maize and wheat growth and lowering Cd uptake under Cd stress.     

Influence of soil and hydrocarbon properties on the solvent extraction of high-concentration weathered petroleum from contaminated soils

Petroleum ether was used to extract petroleum hydrocarbons from soils collected from six oil fields with different history of exploratory and contamination. It was capable of fast removing 76–94 % of the total petroleum hydrocarbons including 25 alkanes (C₁₁–C₃₅) and 16 US EPA priority polycyclic aromatic hydrocarbons from soils at room temperature. The partial least squares analysis indicated that the solvent extraction efficiencies were positively correlated with soil organic matter, cation exchange capacity, moisture, pH, and sand content of soils, while negative effects were observed in the properties reflecting the molecular size (e.g., molecular weight and number of carbon atoms) and hydrophobicity (e.g., water solubility, octanol–water partition coefficient, soil organic carbon partition coefficient) of hydrocarbons. The high concentration of weathered crude oil at the order of 10⁵ mg kg^?1 in this study was demonstrated adverse for solvent extraction by providing an obvious nonaqueous phase liquid phase for hydrocarbon sinking and increasing the sequestration of soluble hydrocarbons in the insoluble oil fractions during weathering. A full picture of the mass distribution and transport mechanism of petroleum contaminants in soils will ultimately require a variety of studies to gain insights into the dynamic interactions between environmental indicator hydrocarbons and their host oil matrix.     

Non-enhanced phytoextraction of cadmium,zinc, and lead by high-yielding crops

Heavy metal soil contamination from mining and smelting has been reported in several regions around the world, and phytoextraction, using plants to accumulate risk elements in aboveground harvestable organs, is a useful method of substantially reducing this contamination. In our 3-year experiment, we tested the hypothesis that phytoextraction can be successful in local soil conditions without external fertilizer input. The phytoextraction efficiency of 15 high-yielding crop species was assessed in a field experiment performed at the Litavka River alluvium in the P?íbram region of Czechia. This area is heavily polluted by Cd, Zn, and Pb from smelter installations which also polluted the river water and flood sediments. Heavy metal concentrations were analyzed in the herbaceous plants’ aboveground and belowground biomass and in woody plants’ leaves and branches. The highest Cd and Zn mean concentrations in the aboveground biomass were recorded in Salix x fragilis L. (10.14 and 343 mg kg^?1 in twigs and 16.74 and 1188 mg kg^?1 in leaves, respectively). The heavy metal content in woody plants was significantly higher in leaves than in twigs. In addition, Malva verticillata L. had the highest Cd, Pb, and Zn concentrations in herbaceous species (6.26, 12.44, and 207 mg kg^?1, respectively). The calculated heavy metal removal capacities in this study proved high phytoextraction efficiency in woody species; especially for Salix × fragilis L. In other tested plants, Sorghum bicolor L., Helianthus tuberosus L., Miscanthus sinensis Andersson, and Phalaris arundinacea L. species are also recommended for phytoextraction.     

Residues levels of organochlorine pesticide in cow's milk from industrial farms in Hidalgo,Mexico

A survey was carried out from 2008 to 2010 to determine the concentrations of 16 organochlorine pesticide residues (OPRs) from Tizayuca, Hidalgo, Mexico. Organochlorine residue determinations were made from milk fat, using chromatographic cleanup and analysis by gas chromatography with an electron capture detector. The OPR concentrations found were from below the detection limit (DL) to 0.91 ng g^?1 in 2008, DL to 0.38 ng g^?1 in 2009 and DL to 0.59 ng g^?1 in 2010. In general concentrations of organochlorine pesticides were higher in the wet season (3.37 ng g^?1 and 4.79 ng g^?1) than the dry season (1.92 ng g^?1 and 2.71 ng g^?1) for 2009 and 2010, due to control of pests in the pasture and sheds. According to Codex Alimentarius regulations, individual pesticides did not exceed the permissible limits, which for example were 10 μg kg^?1 for alpha hexachlorocyclohexane (HCH) and endosulfan I, 20 μg kg^?1 for p,p’-DDT, and 6 μg kg^?1 for dieldrin, endrin and heptachlor. A reduction of organochlorine pesticide concentrations in cow's milk was noted, indicating that the Mexican government has achieved reduction or elimination of some organochlorine pesticides in response to global agreements on persistent organic pollutants.     

Modelling the adsorption of mercury onto natural and aluminium pillared clays

Introduction

The removal of heavy metals by natural adsorbent has become one of the most attractive solutions for environmental remediation. Natural clay collected from the Late Cretaceous Aleg formation, Tunisia was used as a natural adsorbent for the removal of Hg(II) in aqueous system.

Methods

Physicochemical characterization of the adsorbent was carried out with the aid of various techniques, including chemical analysis, X-ray diffraction, Fourier transform infrared and scanning electron micrograph. Batch sorption technique was selected as an appropriate technique in the current study. Method parameters, including pH, temperature, initial metal concentration and contact time, were varied in order to quantitatively evaluate their effects on Hg(II) adsorption onto the original and pillared clay samples. Adsorption kinetic was studied by fitting the experimental results to the pseudo-first-order and pseudo-second-order kinetic models. The adsorption data were also simulated with Langmuir, Freundlich and Temkin isotherms.

Results

Results showed that the natural clay samples are mainly composed of silica, alumina, iron, calcium and magnesium oxides. The sorbents are mainly mesoporous materials with specific surface area of <250 m² g^?1. From the adsorption of Hg(II) studies, experimental data demonstrated a high degree of fitness to the pseudo-second-order kinetics with an equilibration time of 240 min. The equilibrium data showed the best model fit to Langmuir model with the maximum adsorption capacities of 9.70 and 49.75 mg g^?1 for the original and aluminium pillared clays, respectively. The maximum adsorption of Hg(II) on the aluminium pillared clay was observed to occur at pH 3.2. The calculated thermodynamic parameters (?G°, ?H° and ?S°) showed an exothermic adsorption process. The entropy values varied between 60.77 and 117.59 J?mol^?1 K^?1, and those of enthalpy ranged from 16.31 to 30.77 kJ mol^?1. The equilibrium parameter (R _L) indicated that the adsorption of Hg(II) on Tunisian smectitic clays was favourable under the experimental conditions of this study.

Conclusion

The clay of the Aleg formation, Tunisia was found to be an efficient adsorbent for Hg(II) removal in aqueous systems.     

Australian native plant species Carpobrotus rossii (Haw.) Schwantes shows the potential of cadmium phytoremediation

Many polluted sites are typically characterized by contamination with multiple heavy metals, drought, salinity, and nutrient deficiencies. Here, an Australian native succulent halophytic plant species, Carpobrotus rossii (Haw.) Schwantes (Aizoaceae) was investigated to assess its tolerance and phytoextraction potential of Cd, Zn, and the combination of Cd and Zn, when plants were grown in soils spiked with various concentrations of Cd (20–320 mg kg^?1 Cd), Zn (150–2,400 mg kg^?1 Zn) or Cd + Zn (20?+?150, 40?+?300, 80?+?600 mg kg^?1). The concentration of Cd in plant parts followed the order of roots > stems > leaves, resulting in Cd translocation factor (TF, concentration ratio of shoots to roots) less than one. In contrast, the concentration of Zn was in order of leaves > stems > roots, with a Zn TF greater than one. However, the amount of Cd and Zn were distributed more in leaves than in stems or roots, which was attributed to higher biomass of leaves than stems or roots. The critical value that causes 10 % shoot biomass reduction was 115 μg g^?1 for Cd and 1,300 μg g^?1 for Zn. The shoot Cd uptake per plant increased with increasing Cd addition while shoot Zn uptake peaked at 600 mg kg^?1 Zn addition. The combined addition of Cd and Zn reduced biomass production more than Cd or Zn alone and significantly increased Cd concentration, but did not affect Zn concentration in plant parts. The results suggest that C. rossii is able to hyperaccumulate Cd and can be a promising candidate for phytoextraction of Cd from polluted soils.     

The short-term effect of cadmium on low molecular weight organic acid and amino acid exudation from mangrove (Kandelia obovata (S., L.) Yong) roots

The aim of this study was to evaluate short-term concentration and time effects of cadmium on Kandelia obovata (S., L.) Yong root exudation, thereby evaluating and predicting the ecophysiological effects of mangrove to heavy metals at the root level. Mature K. obovata propagules were cultivated in a sandy medium for 3 months, and then six concentrations of Cd (0, 2.5, 5, 10, 20, and 40 mg L^?1) were applied. After exposure time of 24 h and 7 days, respectively, the root exudates of K. obovata were collected and low molecular weight organic acids (LMWOAs) and amino acids of which were analyzed. In addition, we measured glutathione, soluble protein content, and Cd concentration in the plant. We found 10 and 15 types of LMWOAs and amino acids in root exudates of K. obovata with total concentrations ranging from 29.54 to 43.08 mg g^?1 dry weight (DW) roots and from 737.35 to 1,452.46 ng g^?1 DW roots, respectively. Both of them varied in quality and quantity under different Cd treatment strengths and exposure times. Oxalic, acetic, l-malic, tartaric acid, tyrosine, methionine, cysteine, isoleucine, and arginine were dominant. Both LMWOAs and amino acids excreted from K. obovata roots play a key role in Cd toxicity resistance. The responsiveness of amino acids was less than that of LMWOAs. We suggest that the ecological effect of root-excreted free amino acids in the rhizosphere is mainly based on the role of nutrients, supplemented with detoxification to heavy metals.