Interim pump-and-treat remediation of a hydrocarbon-contaminated aquifer

The continuous and discontinuous release of petroleum hydrocarbons from an oil refinery in Alaska resulted in the contamination of an unconfined glacial outwash aquifer. Geologic conditions at the site allowed for the vertical migration of hydrocarbon product to the water table and subsequent formation of an areally extensive floating product layer. Since the petroleum hydrocarbon phase would provide a major source of BTX (benzene, toluene, xylene) contamination to the groundwater, interim product and groundwater recovery measures were initiated to limit aquifer degradation. Phase I remedial activities involved the operation of nine well pairs, with one well used for groundwater extraction and the other for product recovery. Phases II and III involved expansion of the recovery well network and use of a two-pump system. Petroleum product recovered was reprocessed at the refinery. Contaminated groundwater was initially treated using the refinery's wastewater treatment system, but treatment inefficiencies and continued system expansion necessitated use of a separate treatment unit. Performance evaluations indicate that the remedial phases have been successful in halting further contaminant migration and in recovering a significant volume of the released petroleum hydrocarbons.     

Let biodegradation promote in-situ soil venting

Although vapor extraction systems (VES) certainly help remediate volatile hydrocarbons (e.g., gasoline in unsaturated soils), recent studies have found that much of the related hydrocarbon removal is due to aerobic biodegradation, not simple volatilization. In many cases, more than 50 percent of the hydrocarbon removal by these systems is due to biodegradation. By emphasizing biodegradation and minimizing volatilization, the costs of system operation can be reduced, especially for off-gas treatment. Maximizing biodegradation also supports more efficient site remediation because not only are the volatile hydrocarbons cleaned up, but the less volatile contaminants are also cleaned up—by biodegradation. More complete site cleanups are possible through bioventing, especially when cleanup criteria are related to total petroleum hydrocarbons. This article explores the major environmental conditions that influence biodegradation, analyzes several bioventing case histories, and calculates biodegradation's remedial costs.     

Multiphase extraction radius of influence: Evaluation of design and operational parameters

A common remedial technology for properties with subsurface soil and groundwater contamination is multiphase extraction (MPE). MPE involves the extraction of contaminated groundwater, free‐floating product, and contaminated soil vapor from the subsurface. A network of recovery wells conveys fluids to a vacuum pump and to the treatment system for the contaminated groundwater and soil vapor. This article describes a study of MPE operational data from nine similar remediation projects to determine the most important design parameters. Design equations from guidance manuals were used to estimate the expected radius of influence (ROI) based on measured field data. ROIs were calculated for the vapor flow rate through the subsurface and for the groundwater drawdown caused by the MPE remediation activities. The calculated ROIs were compared to the measured ROIs to corroborate the assumptions made in the calculations. Once it was established that the calculated and field‐measured ROIs were comparable, a sensitivity analysis determined ranges of different design and operational parameters that most affected the ROIs. © 2012 Wiley Periodicals, Inc.     

Remedial Process Optimization and Ozone Sparging for Petroleum Hydrocarbon‐Impacted Groundwater

A former natural gas processing station is impacted with total petroleum hydrocarbons (TPH) and benzene. Remedial process optimization (RPO) was conducted to evaluate the effectiveness of the historical air sparging/soil vapor extraction (AS/SVE) system and the current groundwater extraction and treatment system. The RPO indicated that both remedial activities offered no further benefit in meeting remediation goals. Instead, an in situ chemical oxidation (ISCO) system was recommended. Ozone was selected, and the results of a bench test indicated that the ozone demand was 8 to 12 mg ozone/mg TPH and that secondary by‐products would include hexavalent chromium and bromate. A capture zone analysis was conducted through groundwater flow modeling (MODFLOW) to ensure containment of the injected oxidant using the existing groundwater extraction system. Results of a pilot study indicated that the optimum frequency of ozone sparging is 60 minutes in order to reach a maximum radius of influence of 20 feet. TPH concentrations within the treatment zone decreased by 97 percent over two months of ozone sparging. Concentrations of hexavalent chromium and bromate increased from nondetect to 44 and 110 mg/L, respectively, during the ozone sparging but attenuated to nondetectable concentrations within three months of system shut down. ©2016 Wiley Periodicals, Inc.     

Radiolytic decomposition of environmental contaminants and site remediation using an electron accelerator

Halogenated and nonhalogenated hydrocarbon contaminants are currently found in natural waterways, groundwater, and soils as a result of spills and careless disposal practices. The development of proper treatment methodologies for the waste streams producing this environmental damage is now a subject of growing concern. A significant number of these waste stream compounds are chemically stable and are thus resistant to environmental degradation. Numerous researchers have investigated the use of ionizing radiation to decompose chlorinated hydrocarbons in diverse matrices and have proposed various free-radical-induced reaction mechanisms. This article is divided into two sections. First, we present data on experimentally measured, radiolytically induced decomposition of hazardous wastes and toxic substances using accelerator-generated bremsstrahlung sources and gamma radiation from cobalt-60. Data are presented on the radiolytically induced reduction in concentration of volatile organic compounds (VOCs) dissolved in water and in air, polychlorinated biphenyls (PCBs) dissolved in oil, high explosives dissolved in groundwater, and chemical weapon surrogates. The results of these studies suggest the potential use of ionizing radiation as a method of hazardous waste treatment. The second section of this article describes the technical aspects of a field-scale radiolytic decomposition site cleanup demonstration using an electron accelerator. A portable, commercially available electron accelerator was set up at the Lawrence Livermore National Laboratory's (LLNL's) Site 300, a Superfund site, where vacuum extraction wells were removing trichloroethylene (TCE) vapor from a ground spill into the unsaturated soil zone. The accelerator was retrofitted into the existing vacuum extraction system such that the extracted TCE-containing vapor passed through the accelerator beam for treatment. The concentration of TCE in the vapor was reduced by an amount dependent on the accelerator beam power. Production of reaction products in the vapor was measured as a function of absorbed dose.     

Effective low-temperature thermal aeration of soils

Low-temperature thermal aeration (LTTA) is a remedial technology developed by Canonie Environmental Services Corp. (Canonie) for use on soils containing nonchlorinated hydrocarbons, chlorinated solvents, volatile organic compounds (VOCs), chlorinated pesticides, and low levels of polynuclear aromatic hydrocarbons (PAHs). The LTTA system separates these hazardous constituents from excavated soils and allows the treated soils to be redeposited on-site without restriction. This article describes the various components and operation of LTTA systems for the remediation of soils contaminated with chlorinated and nonchlorinated constituents. The article also details the results of projects completed to date, principally for soil impacted with chlorinated hydrocarbons, and discusses the general characteristics and results of systems used for soils contaminated with nonchlorinated hydrocarbons (gasoline, etc.).     

In situ thermal remediation of DNAPL and LNAPL using electrical resistance heating

Electrical resistance heating (ERH) is an in situ treatment for soil and groundwater remediation that can reduce the time to clean up volatile organic compounds (VOCs) from years to months. The technology is now mature enough to provide site owners with both performance and financial certainty in their site‐closure process. The ability of the technology to remediate soil and groundwater impacted by chlorinated solvents and petroleum hydrocarbons regardless of lithology proves to be beneficial over conventional in situ technologies that are dependent on advective flow. These conventional technologies include: soil vapor recovery, air sparging, and pumpand‐treat, or the delivery of fluids to the subsurface such as chemical oxidization and bioremediation. The technology is very tolerant of subsurface heterogeneities and actually performs as well in low‐permeability silts and clay as in higher‐ permeability sands and gravels. ERH is often implemented around and under buildings and public access areas without upsetting normal business operations. ERH may also be combined with other treatment technologies to optimize and enhance their performance. This article describes how the technology was developed, how it works, and provides two case studies where ERH was used to remediate complex lithologies. © 2005 Wiley Periodicals, Inc.     

Successful solid-phase bioremediation of petroleum-contaminated soil

Biological processes have been used to remediate petroleum hydrocarbons, pesticides, chlorinated solvents, and halogenated aromatic hydrocarbons. Biological treatment of contaminated soils may involve solid-phase, slurry-phase, or in situ treatment techniques. This article will review the general principle of solid-phase bioremediation and discuss the application of this technique for the cleanup of total petroleum hydrocarbons on two sites. These remedial programs will reduce total petroleum hydrocarbon contamination from the mean concentration of 2,660 ppm to under the 200-ppm cleanup criteria for soil and under the 15-ppm cleanup criteria for groundwater. Over 32,000 yards of soil have been treated by solid-phase treatment to date. The in situ system operation is effectively producing biodegradation in the subsurface. The project is approximately one-third complete.     

Soil Vapor Extraction and Chemical Oxidation to Remediate Chlorinated Solvents in Fractured Crystalline Bedrock: Pilot Study Results and Lessons Learned

A pilot study was completed at a fractured crystalline bedrock site using a combination of soil vapor extraction (SVE) and in‐situ chemical oxidation (ISCO) with Fenton's Reagent. This system was designed to destroy 1,1,1‐trichloroethane (TCA) and its daughter products, 1,1‐dichloroethene (DCE) and 1,1‐dichloroethane (DCA). Approximately 150 pounds of volatile organic compounds (VOCs) were oxidized in‐situ or removed from the aquifer as vapor during the pilot study. Largely as a result of chemical oxidation, TCA concentrations in groundwater located within a local groundwater mound decreased by 69 to 95 percent. No significant rebound in VOC concentration was observed in these wells. Wells located outside of the groundwater mound showed less dramatic decreases in VOC concentration, and the data show that vapor stripping and short‐term groundwater migration following the oxidant injection were the key processes at these wells. Although the porosity of the aquifer at the site is on the order of 2 percent or less, the pilot study showed that SVE could be an effective remedial process in fractured crystalline rock. © 2002 Wiley Periodicals, Inc.     

Electro‐Thermal Dynamic Stripping Process for in situ remediation under an occupied apartment building

The implementation and performance results of the Electro‐Thermal Dynamic Stripping Process (ET‐DSP?) used in combination with high‐vacuum dual‐phase extraction are presented here. The technology was selected to remove vapor pressure‐sensitive benzene, toluene, ethyl benzene, and xylene (BTEX) compounds from under an occupied residential apartment building. Operating within several engineering, environmental, and safety constraints, a design was developed to conduct electrical heating and in situ extraction operations without disruption of the daily activities of the residents within the apartment complex and general area. The results consistently showed a significant reduction in the concentration of hydrocarbons with non‐detectable levels being achieved in all of the samples that were tested. This is a direct result of a substantial temperature increase of the soil and concurrent increase in the hydrocarbon vapor pressure from the ET‐DSP? system. © 2003 Wiley Periodicals, Inc.     

Augmenting in-situ remediation by soil vapor extraction with six-phase soil heating

The use and performance of soil vapor extraction (SVE) as an in-situ remedial technology has been limited at numerous sites because of both geologic and chemical factors. SVE systems are not well suited to sites containing low permeability soils or sites contaminated with recalcitrant compounds. Six-phase soil heating (SPSH) has been developed by the Battelle Pacific Northwest Laboratories (Battelle) to enhance SVE systems. The technology utilizes resistive soil heating to increase the vapor pressure of subsurface contaminants and to generate an in-situ source of steam. The steam strips contaminants sorbed onto soil surfaces and acts as a carrier gas, providing an enhanced mechanism by which the contaminants can reach an extraction well. Full-scale applications of SPSH have been performed at the U.S. Department of Energy's Savannah River Site in Aiken, South Carolina; at a former fire training site in Niagara Falls, New York; and at Fort Richardson near Anchorage, Alaska. At each site, chlorinated solvents were present in low permeability soils and SPSH was applied in conjunction with SVE. The results of the three applications showed that SPSH is a cost-effective technology that can reduce the time required to remediate a site using only conventional SVE.     

Passive soil vapor extraction: A cost effectiveness study

An analysis of the cost effectiveness of passive soil vapor extraction (PSVE) is presented. PSVE, or “barometric pumping,” is an approach to the remediation of volatile organic compounds (VOCs) that seeks to harness and enhance the naturally occurring processes of wind and atmospheric pressure changes to facilitate the release of gas-phase contaminants from the subsurface. The technology background and current status are discussed, niches for the potential applicability of PSVE are identified, and a cost comparison with the conventional treatment method of active soil vapor extraction (ASVE) is examined.     

石油烃污染地下水原位修复技术研究进展

概述了石油烃污染地下水原位修复技术的进展，包括原位化学氧化、原位电动修复、渗透反应格栅、冲洗、土壤气抽出、地下水曝气、生物修复，并对今后的研究发展趋势进行了展望。     

ART in‐well air stripping—An innovative technology succeeds where other technologies have failed

Accelerated Remediation Technologies LLC (ART) developed a proprietary (patent‐pending) effective remediation technology that is based on verified and established concepts. The ART technology combines in‐situ air stripping, air sparging, soil vapor extraction, enhanced bioremediation/oxidation, and Dynamic Subsurface Circulation^TM in an innovative wellhead system. The system is designed to accommodate a 4‐inch well and is cost‐effective when compared with other remediation technologies. The air‐sparging component results in lifting the water table. This lifting of the water in the well causes a net reduction in head at the well location. Vacuum pressure (the vapor‐extraction component) is applied on top of the well point to extract vapor from the subsurface. The negative pressure from the vacuum extraction results in water suction that creates additional water lifting (mounding). A submersible pump is placed at the bottom of the well to recirculate water to the top for downward discharge through a spray head. The water cascades down the interior of the well similar to what occurs in an air‐stripping tower. Enhanced stripping via air sparging near the bottom of the well occurs simultaneously. In essence, the well acts as a subsurface air‐stripping tower. The pumped‐and‐stripped, highly oxygenated water flows down well annulus and over the “mounded” water back in to the aquifer, which creates a circulation zone around the well to further enhance cleanup. The ART technology has been implemented at several sites nationwide, including industrial laundry facilities, manufacturing plants, and service stations, and has achieved significant reductions in contaminant concentrations. Specifically, a concentration of tetrachloroethene (PCE) decreased from 2,700 to 240 μg/l, in 13 days. In less than three months, the concentrations dropped further to 79 μg/l, which is within the range of background levels. Other sites utilizing the technology have exhibited similar reduction trends in complex subsurface environments. © 2002 Wiley Periodicals, Inc.     

A practical approach to steam‐enhanced dual‐phase extraction: A case study

This article presents the results of a pilot test that was conducted to determine the effectiveness of using steam‐enhanced dual‐phase extraction (DPE) at a former industrial site in New York. The pilot test proved that steam‐enhanced DPE was very effective at removing significant contaminant mass from the subsurface in a relatively short time period. Concentrations of volatile organic compounds and semivolatile organic compounds in the vapor stream and groundwater were successfully reduced, in some cases by orders of magnitude. Based on the results of the steam‐enhanced DPE pilot test, the final remedy for the site includes implementing this technology at selected areas as an alternative to DPE alone or other remedial alternatives, such as excavation or groundwater pump and treat. © 2003 Wiley Periodicals, Inc.     

Use of mixed technologies to remediate chlorinated DNAPL at a Brownfields site

A former chlorofluorocarbon manufacturing facility in northern New Jersey was purchased for redevelopment as a warehousing/distribution center as part of the New Jersey Department of Environmental Protection's Brownfields redevelopment initiative. Soil and groundwater at the site were impacted with dense nonaqueous‐phase liquids (chlorinated organic compounds) and light nonaqueous‐phase liquids (petroleum hydrocarbons). The initial remedial strategy (excavation and offsite disposal) developed by prior site owners would have been cost‐prohibitive to the new site owners and made redevelopment infeasible. Mixed remedial technologies were employed to reduce the cost of remediation while meeting regulatory contaminant levels that are protective of human health and the environment. The most heavily impacted soils (containing greater than 95 percent of the contaminant mass) were excavated and treated onsite by the addition of calcium oxide and lime kiln dust coupled with physical mixing. Treated soils were reused onsite as part of the redevelopment. Residual soil and groundwater contamination was treated via in situ injections of emulsified oil to enhance anaerobic biodegradation, and emulsified oil/zero‐valent iron to chemically reduce residual contaminants. Engineering (cap) and administrative (deed restriction) controls were used as part of the final remedy. The remedial strategy presented in this article resulted in a cost reduction of 50 percent of the initial remedial cost estimate. © 2008 Wiley Periodicals, Inc.     

Sustainable wind‐driven bioventing at a petroleum hydrocarbon–impacted site

Bioventing—the injection of air into the vadose zone to increase microbial activity—is a commonly used, proven technology for remediating volatile organic compounds present in the vadose zone. Passive systems driven by wind or solar power are both more cost‐effective and sustainable than conventional systems. Such a passive system is being applied successfully to remediate a site impacted with total petroleum hydrocarbons (TPH) and benzene, toluene, ethylbenzene, and xylenes (BTEX) in soil. Bioventing technology was approved by the regulatory agency as an interim remedial action to remove chemicals of concern (COCs) in the vadose zone. A bioventing pilot study was conducted to evaluate the effectiveness of COC removal and collect parameters for full‐scale design and implementation. To evaluate the potential to use wind‐driven bioventing technology, two mobile weather stations were installed at the site and monitored for one month for a wind speed study. Based on the pilot‐test data and wind speed research, 12‐inch diameter funnel/vane 360‐degree wind collectors were designed as passive wind‐driven air‐injection devices and connected to existing monitoring wells. The measured air velocity ranged from 20 to 110 feet per minute during the start‐up and the first three months of operation and maintenance. Monitoring indicated a 20 percent oxygen delivery and greater than 90 percent reduction in COC concentrations, demonstrating a successful sustainable remediation with no power requirement and minimal operation and maintenance. © 2012 Wiley Periodicals, Inc.     

Estimating Remediation and Contaminant Respiration Emissions for Alternatives Comparisons at Petroleum Spill Sites

Greenhouse gas emissions assessments for site cleanups typically quantify emissions associated with remediation and not those from contaminant biodegradation. Yet, at petroleum spill sites, these emissions can be significant, and some remedial actions can decrease this additional component of the environmental footprint. This article demonstrates an emissions assessment for a hypothetical site, using the following technologies as examples: excavation with disposal to a landfill, light nonaqueous‐phase liquid (LNAPL) recovery with and without recovered product recycling, passive bioventing, and monitored natural attenuation (MNA). While the emissions associated with remediation for LNAPL recovery are greater than the other considered alternatives, this technology is comparable to excavation when a credit associated with product recycling is counted. Passive bioventing, a green remedial alternative, has greater remedial emissions than MNA, but unlike MNA can decrease contaminant‐related emissions by converting subsurface methane to carbon dioxide. For the presented example, passive bioventing has the lowest total emissions of all technologies considered. This illustrates the value in estimating both remediation and contaminant respiration emissions for petroleum spill sites, so that the benefit of green remedial approaches can be quantified at the remedial alternatives selection stage rather than simply as best management practices. ©2015 Wiley Periodicals, Inc.     

ART in‐well technology proves effective in treating 1,4‐dioxane contamination

A common industrial solvent additive is 1,4‐dioxane. Contamination of dissolved 1,4‐dioxane in groundwater has been found to be recalcitrant to removal by conventional, low‐cost remedial technologies. Only costly labor and energy‐intensive pump‐and‐treat remedial options have been shown to be effective remedies. However, the capital and extended operation and maintenance costs render pump‐and‐treat technologies economically unfeasible at many sites. Furthermore, pump‐and‐treat approaches at remediation sites have frequently been proven over time to merely achieve containment rather than site closure. A major manufacturer in North Carolina was faced with the challenge of cleaning up 1,4‐dioxane and volatile organic compound–impacted soil and groundwater at its site. Significant costs associated with the application of conventional approaches to treating 1,4‐dioxane in groundwater led to an alternative analysis of emerging technologies. As a result of the success of the Accelerated Remediation Technologies, LLC (ART) In‐Well Technology at other sites impacted with recalcitrant compounds such as methyl tertiarybutyl ether, and the demonstrated success of efficient mass removal, an ART pilot test was conducted. The ART Technology combines in situ air stripping, air sparging, soil vapor extraction, enhanced bioremediation/oxidation, and dynamic subsurface groundwater circulation. Monitoring results from the pilot test show that 1,4‐dioxane concentrations were reduced by up to 90 percent in monitoring wells within 90 days. The removal rate of chlorinated compounds from one ART well exceeded the removal achieved by the multipoint soil vapor extraction/air sparging system by more than 80 times. © 2005 Wiley Periodicals, Inc.