Environmental noise has been growing in recent years, causing numerous health problems. Highly sensitive environments such as hospitals deserve special attention, since noise can aggravate patients’ health issues and impair the performance of healthcare professionals. This work consists of a systematic review of scientific articles describing environmental noise measurements taken in hospitals between the years 2015 and 2020. The researchers started with a consultation of three databases, namely, Scopus, Web of Science, and ScienceDirect. The results indicate that for the most part, these studies are published in journals in the fields of medicine, engineering, environmental sciences, acoustics, and nursing and that most of their authors work in the fields of architecture, engineering, medicine, and nursing. These studies, which are concentrated in Europe, the Americas, and Asia, use as reference values sound levels recommended by the World Health Organization. Leq measured in hospital environments showed daytime values ranging from 37 to 88.6 dB (A) and nighttime values of 38.7 to 68.8 dB (A). Leq values for outdoor noise were 74.3 and 56.6 dB (A) for daytime and nighttime, respectively. The measurements were taken mainly inside hospitals, prioritizing more sensitive departments such as intensive care units. There is a potential for growth in work carried out in this area, but research should also include discussions about guidelines for improvement measures aimed at reducing noise in hospitals.
Noise is a major source of pollution that can affect the human physiology and living environment. According to the World Health Organization (WHO), an exposure for longer than 24 hours to noise levels above 70 dB(A) may damage human hearing sensitivity, induce adverse health effects, and cause anxiety to residents nearby roadways. Pavement type with different roughness is one of the associated sources that may contribute to in-vehicle noise. Most previous studies have focused on the impact of pavement type on the surrounding acoustic environment of roadways, and given little attention to in-vehicle noise levels. This paper explores the impacts of different pavement types on in-vehicle noise levels and the associated adverse health effects. An old concrete pavement and a pavement with a thin asphalt overlay were chosen as the test beds. The in-vehicle noise caused by the asphalt and concrete pavements were measured, as well as the drivers’ corresponding heart rates and reported riding comfort. Results show that the overall in-vehicle sound levels are higher than 70 dB(A) even at midnight. The newly overlaid asphalt pavement reduced in-vehicle noise at a driving speed of 96.5 km/hr by approximately 6 dB(A). Further, on the concrete pavement with higher roughness, driver heart rates were significantly higher than on the asphalt pavement. Drivers reported feeling more comfortable when driving on asphalt than on concrete pavement. Further tests on more drivers with different demographic characteristics, along highways with complicated configurations, and an examination of more factors contributing to in-vehicle noise are recommended, in addition to measuring additional physical symptoms of both drivers and passengers.Implications: While there have been many previous noise-related studies, few have addressed in-vehicle noise. Most studies have focused on the noise that residents have complained about, such as neighborhood traffic noise. As yet, there have been no complaints by drivers that their own in-vehicle noise is too loud. Nevertheless, it is a fact that in-vehicle noise can also result in adverse health effects if it exceeds 85 dB(A). Results of this study show that in-vehicle noise was strongly associated with pavement type and roughness; also, driver heart rate patterns presented statistically significant differences on different types of pavement with different roughness. 相似文献
There have been many previous noise-related studies on liquefied natural gas (LNG) facilities in the United States; however, noise control of these facilities using a top-down approach has not been explored in detail. Most studies have demonstrated noise compliance to applicable standards by focusing on a combination of treatments and specifications, with less consideration on control technology feasibility, ranking, and cost-effectiveness. The Federal Energy Regulatory Commission (FERC) prohibits natural gas facilities from emitting day-night noise levels in excess of 55 dB(A) (equivalent to 24-hr continuous level of 49 dB(A)) at nearby receivers. A case study was conducted to evaluate a top-down approach to reduce noise at a typical LNG peak-shaving facility under normal operating conditions, accounting for technical feasibility, control effectiveness, and cost implications. A modeling approach (International Organization for Standardization standard ISO 9613-2) was used to predict and evaluate the facility’s noise reduction potential. The study found that the strategy could achieve feasible and environmentally effective reductions up to 11 dB(A) at 500 m from the facility by first identifying source groups with highest-emitting sources and then targeting major noise source contributors per group. This approach is cost-effective because the FERC noise goals can still be achieved by avoiding unnecessary control costs associated with lower-ranked sources. The study identified the following four source groups as the highest noise emitters: (1) liquefaction and instrument air, (2) boil-off gas (BOG) compression, (3) glycol water system (air coolers), and (4) pretreatment. Of all the treatments evaluated, installation of enhanced silencers for gas turbine (GT) package—as well as construction of an acoustical building for the BOG compressors and drivers—resulted in the greatest noise reduction at nearby receivers. The study notes that incremental treatment costs presented in this paper are approximate estimates that may vary depending on factors such as facility size and region.
Implications: This study assessed potential noise reductions associated with implementing a top–down noise control strategy on a typical LNG peak-shaving facility. The study determined the top–down noise control strategy could achieve feasible and environmentally effective reductions up to 11 decibels at receivers within 500 m from the facility’s center. As LNG suppliers need to support potential supply disruptions, some regions of the US, including New England and Gulf Coast with projected increase in LNG exports and growing needs from power sector, may find information in this study useful with regard to evaluating and prioritizing noise reduction potential of their LNG peak-shaving facilities. 相似文献
Many energy conservation strategies for residences involve reducing house air exchange rates. Reducing the air exchange rate of a house can cause an increase in pollutant levels if there is an indoor pollution source and if the indoor pollutant source strength remains constant. However, if the indoor pollutant source strength can also be reduced, then it is possible to maintain or even improve indoor air quality. Increasing the insulation level of a house is a means of achieving energy conservation goals and, in addition, can reduce the need for space heating and thereby reduce the pollutant source strengths of combustion space heaters such as unvented kerosene space heaters, unvented gas space heaters, and wood stoves. In this paper, the indoor air quality trade-off between reduced infiltration and increased insulation in residences is investigated for combustion space heaters. Two similar residences were used for the experiment. One residence was used as a control and the other residence had infiltration and insulation levels modified. An unvented propane space heater was used as the source in this study. A model was developed to describe the dependence of both indoor air pollution levels and the appliance source strengths on house air exchange rates and house insulation levels. Model parameters were estimated by applying regression techniques to the data. Results show that indoor air pollution levels in houses with indoor combustion space heating pollution sources can be held constant (or lowered) by reducing the thermal conductance by an amount proportional to (or greater than) the reduction of the air exchange rate. 相似文献