6,6″—二甲基—4′—苯基—2,2′：6′,2′—三联吡啶分光光度法测定水中 …

以6,6″-二甲基-4′-苯基-2,2′:6′,2″-三联吡啶(TPY)为络合剂,用分光光度法测定水中铁的含量.进行了波长、TPY乙醇溶液用量及显色时间等条件的选择.该分析方法表观摩尔吸光系数为2.17×105dm3.mol-1.cm-1,变异系数为3.9%,加标回收率为96.4%～105.6%.     

“水泥—黏土—粉煤灰—生石灰”固化浆液性能试验

松散岩体固化已成为一种提高岩体强度，改善巷道支护条件的重要手段，已应用的固化注浆材料各有特点，如单一水泥浆液的优点是结石体强度高、透水性低，材料来源广、价廉，但其可注性及稳定性较差，凝结时间长，而且凝结时间难以控制等，限制了它的适用范围，而在水泥浆中加入添加剂，则可以改善水泥浆的性能，水泥一粉煤灰浆液可以提高水泥浆的可注性，提高浆液固结的早期强度，增强浆液的稳定性，减少水泥消耗，降低成本。     

Hg—PAN—Triton X—100分光光度法测定污水中微量汞

1-(2-吡啶偶氮)-2-萘酚(简称PAN)萃取比色测定微量汞的方法已有报道,但在水溶液体系中用PAN直接测汞尚无人研究。本文探讨了在TritonX-100存在下,用PAN测定微量汞的具体条件,并应用于环境污水的测定,取得了满意的结果。     

电化学还原—中和絮凝—生化—吸附法处理分散染料生产废水

采用电化学还原－中和絮凝－生化－粉煤灰吸附法处理分散染料废水，处理效果较好。在废水初沉后ＣＯＤ为２８００－３２００ｍｇ／Ｌ、色度为２０００倍的民政部下，处理出水ＣＯＤ〈２００ｍｇ／Ｌ，色度低于２０倍。结果表明，电化学还原对放心水脱色有明显的效果；废水的分散染料可生化性好，对生化过程无明显的抑制作用。     

内电解—Fenton氧化—絮凝沉淀预处理焦化废水

采用内电解—Fenton氧化—絮凝沉淀的化学集成技术预处理焦化废水，优化了各工段的运行参数。实验结果表明：在钢铁铁屑与活性炭的体积比为1∶1的条件下，内电解工段的优化参数为进水pH 2.6~3.1、HRT=1.0 h;Fenton氧化工段的优化参数为Fe2+加入量200 mg/L、H2O2加入量1 000 mg/L、进水pH 3.0左右、反应时间1.0 h;絮凝沉淀工段的设定参数为进水pH 9.5~10.0、聚丙烯酰胺加入量1 mg/L、静置沉降0.5 h。在上述工艺条件下，该集成技术对废水的总COD去除率大于55%，处理后的废水BOD5/COD大于0.28，不添加稀释新水即可进入后续生化处理系统。该工艺占地面积小、系统结构简单、易于工业化，废水预处理成本为4~5元/t。     

二级膜分离—冷凝—吸附工艺处理石化罐区废气

采用二级膜分离—冷凝—变压吸附工艺回收处理含有高浓度挥发性有机物和苯系物的炼厂罐区外排"呼吸气"。结果表明,进气的非甲烷总烃质量浓度范围41 000～182 000 mg/m~3,进气中苯、甲苯和二甲苯的质量浓度分别为400～1 400 mg/m~3,150～1 600 mg/m~3,300～2 100 mg/m~3时,尾气中非甲烷总烃质量浓度始终低于80mg/m~3,去除率均高于99.9%,苯、甲苯和二甲苯的去除率分别为99.6%、99.6%和99.8%。抗冲击负荷实验将进气量提高50%,尾气中非甲烷总烃质量浓度仍低于80 mg/m~3。二级膜单元可以高效浓缩轻烃,既回收获得可燃气,又解决了轻烃积累所造成的尾气超标难题。     

接触氧化—水解—MBR处理头孢类抗生素化学合成废水

采用接触氧化—水解—MBR处理头孢类抗生素化学合成废水,设计进水量350m3/d,实际处理水量385m3/d。在进水COD为2 125~1 1561mg/L(平均进水COD为4 164mg/L)时,出水COD为79~282mg/L(平均出水COD为178mg/L),出水BOD5低于10mg/L,完全满足该工业园区污水纳管标准(COD≤300mg/L,BOD5≤100mg/L)。在平均进水TN、ρ(NH+4-N)和ρ(NO3--N)分别为145.47,0.89,49.25mg/L时,平均出水分别为91.76,78.11,18.61mg/L,系统脱氮能力有限。     

酸浸—萃取—沉淀法回收废锂离子电池中的钴

采用酸浸—萃取—沉淀法回收废锂离子电池中的钴。实验结果表明:废锂离子电池在600℃下煅烧5 h可将正极材料上的有机黏结剂与正极活性物质分离;正极活性物质在Na OH溶液浓度为2.0 mol/L、n(Na OH)∶n(铝)=2.5、碱浸温度为20℃的条件下碱浸反应1 h后,铝浸出率达99.7%;已除铝的正极活性物质在硫酸浓度为2.5 mol/L、H_2O_2质量浓度为7.25 g/L、液固比为10、酸浸温度为85℃的条件下酸浸反应120 min,钴浸出率高达98.0%;酸浸液在p H为3.5、萃取剂P507与Cyanex272体积比为1∶1的条件下,经2级萃取,钴萃取率为95.5%;采用H_2SO_4溶液反萃后在硫化钠质量浓度为8 g/L、反萃液p H为4的条件下沉淀反应10 min,钴沉淀率达99.9%。     

先进的烟气脱硫工艺—CT—121工艺

概述了中国目前的烟气脱硫形势,介绍了ＣＴ－１２１工艺的特点及工作原理,对ＣＴ－１２１脱硫系统的现状进行了综述,重点介绍了美国亚特斯电厂的ＣＴ－１２１示范装置运行情况,并简要评价了该工艺的经济性。     

Determination of the Thermal Efficiency of Pre-boilover Burning of a Slick of Oil on Water

The burning rate of a slick of oil on a water bed is calculated by a simple expression derived from a one-dimensional heat conduction equation. Heat feedback from the flame to the surface is assumed to be a constant fraction of the total energy released by the combustion reaction. The constant fraction (χ) is named the burning efficiency and represents an important tool in assessing the potential of in situ burning as a counter-measure to an oil-spill. The total heat release, as a function of the pool diameter, is obtained from an existing correlation. It is assumed that radiative heat is absorbed close to the fuel surface, that conduction is the dominant mode of heat transfer in the liquid phase and that the fuel boiling temperature remains constant. By matching the characteristic thermal penetration length scale for the fuel/water system and an equivalent single layer system, a combined thermal diffusivity can be calculated and used to obtain an analytical solution for the burning rate. Theoretical expressions were correlated with crude oil and heating oil, for a number of pool diameters and initial fuel layer thickness. Experiments were also conducted with emulsified and weathered crude oil. The simple analytical expression describes well the effects of pool diameter and initial fuel layer thickness permitting a better observation of the effects of weathering, emulsification and net heat feedback to the fuel surface. Experiments showed that only a small fraction of the heat released by the flame is retained by the fuel layer and water bed (of the order of 1%). The effect of weathering on the burning rate decreases with the weathering period and that emulsification results in a linear decrease of the burning rate with water content.     

Calculation of carbon balances for evaluation of the biodegradability of polymers

Establishing carbon balances has been proven to be an applicable and powerful tool in testing biodegradability of polymers. In controlled degradation tests at a 4-L scale with the model polymer poly(-hydroxybutyrate) (PHB), it was shown that the degree of degradation could not be determined with satisfactory accuracy from CO₂ release alone. Instead, the course of degradation was characterized by means of establishing carbon balances for the degradation of PHB withAcidovorax facilis and a mixed culture derived from compost. Different analytical methods for determining the different carbon fractions were adapted to the particular test conditions and compared. Quantitative determination of biomass and residual polymer were the main problems in establishing carbon balances. Amounts of biomass derived from protein measurements depend strongly on assumptions of the protein content of the biomass. Selective oxidation of biomass with hypochlorite was used as alternative, but here problems arose from insoluble metabolic products. Determination of soluble components with the method of chemical oxygen demand (COD) also includes empirical assumptions but seems acceptable if the dissolved carbon fraction is in the range of some 10% total carbon. Results confirm both analytical assays and theoretical approaches, in ending up at values very close to 100%, within an acceptable standard deviation range under test conditions comparable to standard test practice.Paper presented at the Bio/Environmentally Degradable Polymer Society—Third National Meeting, June 6–8, 1994, Boston, Massachusetts.     

富拉尔基发电总厂200MW机组除尘器改造

对富拉尔基发电总厂5号炉的设计条件进行了分析，针对燃用低硫煤，飞灰比电阻高，场地较小，除尘效率要求高的情况，在电除尘器的设计上采取有效措施，达到了排放要求。     

Review of the kinetics of alkaline degradation of cellulose in view of its relevance for safety assessment of radioactive waste repositories

The degradation of cellulose (a substantial component of low- and intermediate-level radioactive waste) under alkaline conditions occurs via two main processes: a peeling-off reaction and a basecatalyzed cleavage of glycosidic bonds (hydrolysis). Both processes show pseudo-first-order kinetics. At ambient temperature, the peeling-off process is the dominant degradation mechanism, resulting in the formation of mainly isosaccharinic acid. The degradation depends strongly on the degree of polymerization (DP) and on the number of reducing end groups present in cellulose. Beyond pH 12.5, the OH^- concentration has only a minor effect on the degradation rate. It was estimated that under repository conditions (alkaline environment, pH 13.3-12.5) about 10% of the cellulosic materials (average DP = 1000-2000) will degrade in the first stage (up to 10⁵ years) by the peeling-off reaction and will cause an ingrowth of isosaccharinic acid in the interstitial cement pore water. In the second stage (10⁵-10⁶ years), alkaline hydrolysis will control the further degradation of the cellulose. The potential role of microorganisms in the degradation of cellulose under alkaline conditions could not be evaluated. Proper assessment of the effect of cellulose degradation on the mobilization of radionuclides basically requires knowing the concentration of isosaccharinic acid in the pore water. This concentration, however, depends on several factors such as the stability of ISA under alkaline conditions, sorption of ISA on cement, formation of sparingly soluble ISA-salts, etc. A discussion of all the relevant processes involved, however, is far beyond the scope of the presented overview.     

Study of Aging Characteristics of Ternary Blends of Polyethylenes—II

Six film samples of low-density polypropylene (LDPE)/linear LDPE (LLDPE)/high-density polypropylene (HDPE) with varying ratios of LDPE (20–45 ... wt%) and LLDPE (25–50 wt%) having a fixed amount of HDPE at 30 wt% were prepared by blown film extrusion technique. The samples were aged at four different temperatures, 55°, 70°, 85°, and 100°C, for four different time periods in the interval of between 150 hours and up to 600 hours. The change in the structure of various constituents and the formation of various oxygenated (peroxy and hydroperoxy) and unsaturated groups during thermo-oxidative degradation was discussed by infrared spectroscopy. The visiosity-average molecular weight was found to have decreased slowly in the initial aging hours and temperatures, whereas it decreased by 10% with its previous value tensile strength that is, 100°C when aged for 600 hours. The tensile strength of the sample first increased by 67% at 55°C and 89% at 70°C up to 450 hours, whereas the values increased by 52.5% at 85°C and 33.9% at 100°C when aged for 150 hours and then decreased. The percentage elongation at break increased by 2.7% at 55°C and 10.7% at 70°C for 150 and 300 hours of aging, respectively, whereas the percentage decreased when aged at 85°C and 100°C for up to 600 hours of aging. The values of gel content (percent) increased and initial degradation temperature decreased with aging time and temperature.     

Selection of adsorbents for treatment of leachate: batch studies of simultaneous adsorption of heavy metals

The simultaneous adsorption of copper (Cu), cadmium (Cd), nickel (Ni), and lead (Pb) ions from spiked deionized water and spiked leachate onto natural materials (peat A and B), by-product or waste materials (carbon-containing ash, paper pellets, pine bark, and semi-coke), and synthetic materials (based on urea-formaldehyde resins, called blue and red adsorbents) or mixtures thereof was investigated. The adsorbents that gave the highest metal removal efficiencies were peat A, a mixture of peat B and carbon-containing ash, and a mixture of peat A and blue. At an initial concentration of 5 mg/l for each metal, the removal of each species of metal ion from spiked water and spiked leachate solutions was very good (>90%) and good (>75%), respectively. When the initial concentration of each metal in the solutions was twenty times higher (100 mg/l), there was a noticeable decrease in the removal efficiency of Cu²⁺, Cd²⁺, and Ni²⁺, but not of Pb²⁺. Langmuir monolayer adsorption capacities, q_m, on peat A were found to be 0.57, 0.37, and 0.36 mmol/g for Pb²⁺, Cd²⁺, and Ni²⁺, respectively. The order of metal adsorption capacity on peat A was the same in the case of competitive multimetal adsorption conditions as it was for single-element adsorption, namely Pb²⁺ > Cd²⁺ ≥ Ni²⁺. The results show that peat alone (an inexpensive adsorbent) is a good adsorbent for heavy metal ions.     

袋式除尘器气流分布数值计算研究

采用结构化/非结构化混合网格技术、多孔介质模型及k-ε两方程湍流模型,对某袋式除尘器及进出口管道内的气体流场进行了数值计算.计算结果表明,合理布置导流板后,袋式除尘器两箱体流量偏差为1.8％;除尘器下游滤袋单元处理气量偏大,中游滤袋单元处理气量较小,最大流量与最小流量偏差为22.3％；靠近除尘器进口处灰斗内存在气流回流特性,易造成粉尘的二次附着现象.     

Effect of Degree of Substitution of Octenyl Succinate Starch on Enzymatic Degradation

Octenyl succinate starch of degree of substitution (ds) 0.03, 0.07, and 0.11 was synthesized in an aqueous medium. These compounds were then tested for the susceptibility to enzymatic degradation. The multiple-enzyme regime of -amylase, amyloglucosidase, and pullulanase was chosen for the evaluation. This combination of enzymes had been proven to degrade 99.5% of unmodified starch to glucose and hence was chosen for this study. It was found that even small amounts of subsituent caused a considerable decrease in the extent of degradation. The net extent of degradation decreased with increasing ds. Surprisingly, the amount of glucose from all three substituted substrates was quite similar, suggesting the effect small amounts of subtituent had on the enzymatic activity.     

Kinetics of Hydrolytic Degradation of PLA

The chemical recycling of poly(lactic acid) (PLA) to its monomer is crucial to reduce both the consumption of renewable resources for the monomer synthesis and the environmental impact related to its production and disposal. In particular, the production of lactic acid from PLA wastes, rather than from virgin raw materials, it is also possible to achieve considerable primary energy savings. The focus of this work is to analyse deeply the PLA hydrolytic decomposition by means of a kinetic model based on two reactions mechanism. To this end, new experimental data have been gathered in order to investigate a wider temperature range (from 140 to 180 °C) and to extend the water/PLA ratio up to 50 % of PLA by weight. The reported results clearly highlight that more than 95 % of PLA is hydrolyzed to water-soluble lactic acid within 120 min, when it is hydrolyzed within 160–180 °C. Furthermore, the kinetic constant is highly influenced by reaction temperature. The proposed “two reactions” kinetic mechanism complies satisfactorily with the experimental data under analysis.     

Effects of temperature on the release of nutrient elements of solid organic materials under conditions of oversaturation

The effects of temperature on the release of chemical components of six solid organic materials under conditions of oversaturation were investigated in this paper. The six materials were peat moss (PM), weathered coals (WC), charred rice husks (CRH), sawdust (Sd), turfgrass clippings (TC), and chicken manure (CM). Significant differences were observed in the available nitrogen and phosphorus content of the aqueous extracts of organic materials at different temperatures. The available nitrogen content in aqueous extracts of PM and WC at 25 °C was higher than that registered at 15 °C and 35 °C. Available nitrogen content in the aqueous extracts of CRH, Sd, TC, and WC at 35 °C was higher than at 15 °C and 25 °C. The available phosphorus content in the aqueous extracts of organic materials at 35 °C was higher than that available at 15 °C and 25 °C, with the exception of Sd. In addition, the release of available phosphorus in the aqueous solution of organic materials at different temperatures varied constantly for 108 h. The release of potassium (K⁺) and sodium (Na⁺) ions in the aqueous extracts of organic materials was basically steady over time, with the exception of CM. High temperature (35 °C) may significantly hasten the release of K⁺ from organic substrates (except for WC) with low temperatures significantly inhibiting release of K⁺ in Sd and CRH. High temperatures (35 °C) might significantly facilitate the release of Na⁺ in CM and TC. However, no significant differences were manifested in the release of Na⁺ from organic substrates at different temperatures, with the exception of CM and TC. Moreover, no significant differences were observed in the release of calcium, magnesium and iron ions with time, nor were there any significant differences in the contents of iron ions in the aqueous extracts of organic materials at different temperatures. The results indicate that multiple mediums should be pretreated in water for a week before being used for planting. They should be used when all mineral elements of organic materials are steady and ignoring the effect of organic mediums.