Bioleaching of metal from municipal waste incineration fly ash using a mixed culture of sulfur-oxidizing and iron-oxidizing bacteria

We investigated the behavior and characteristics of metal leaching from municipal solid waste incineration (MSWI) fly ash among pure cultures of a sulfur-oxidizing bacterium (SOB) and an iron-oxidizing bacterium (IOB) and a mixed culture. The IOB has a high metal-leaching ability, though its tolerability against the ash addition is low. The SOB might better tolerate an increase in ash addition than the IOB, though metal leaching ability of the SOB is limited. Mixed culture could compensate for these deficiencies, and high metal leachability was exhibited in the 1% ash culture, i.e., 67% and 78% of leachabilities for Cu and Zn, respectively, and 100% for Cr and Cd. Furthermore, comparably high leachabilities such as 42% and 78% for Cu and Zn were observed even in the 3% ash cultures. Characterization of metal leaching by the mixed culture revealed that the acidic and oxidizing condition had remained stable thorough the experimental period. Ferric iron remained in the mixed culture, and the metal leaching was enhanced by redox mechanisms coupling with the leaching by sulfate. An increase of ferrous iron enhanced the Cr, Cu, and As leaching. The optimum concentration of sulfur existed for As and Cr (5 gl(-1)) and Cu (2 gl(-1)). The presence of the degradable and non-degradable organic compound that must be existed in the natural environment or waste landfills made no significant change in the leachability of metals other than Zn. These results suggested that bioleaching using a mixed culture of SOB and IOB is a promising technology for recovering the valuable metals from MSWI fly ash.     

Arsenic leachability and speciation in cement immobilized water treatment sludge

Arsenic leachability and speciation in cement immobilized water treatment sludge were investigated with leaching tests and X-ray absorption near edge structure (XANES) spectroscopy. The As leachability in the sludge determined with the toxicity characteristic leaching procedure (TCLP) and the waste extraction test (WET) was 283 and 7490 microgl(-1), respectively. Extractions with a lower liquid to solid ratio, under anaerobic conditions, and using citric acid buffer solution dramatically increased the leachate As concentration. XANES results showed that the As(III) composition was reduced from 51.1% of the total As content in the sludge to 16.3% in the cement treated sample with 28 days of cure. When the cement treated sample was cured for two years, the As(III) composition was decreased to 7.4%. The cement treatment reduced the As leachability. The leachate As(III) and total As concentrations were of the same order of magnitude in the samples cured for 28 days as for 2yr. However, consistently lower concentrations were detected in samples with longer cure time. The results of this study improve our understanding of arsenic speciation and leachability in the cement matrix after long cure times.     

Arsenic and copper stabilisation in a contaminated soil by coal fly ash and green waste compost

In situ metal stabilisation by amendments has been demonstrated as an appealing low-cost remediation strategy for contaminated soil. This study investigated the short-term leaching behaviour and long-term stability of As and Cu in soil amended with coal fly ash and/or green waste compost. Locally abundant inorganic (limestone and bentonite) and carbonaceous (lignite) resources were also studied for comparison. Column leaching experiments revealed that coal fly ash outperformed limestone and bentonite amendments for As stabilisation. It also maintained the As stability under continuous leaching of acidic solution, which was potentially attributed to high-affinity adsorption, co-precipitation, and pozzolanic reaction of coal fly ash. However, Cu leaching in the column experiments could not be mitigated by any of these inorganic amendments, suggesting the need for co-addition of carbonaceous materials that provides strong chelation with oxygen-containing functional groups for Cu stabilisation. Green waste compost suppressed the Cu leaching more effectively than lignite due to the difference in chemical composition and dissolved organic matter. After 9-month soil incubation, coal fly ash was able to minimise the concentrations of As and Cu in the soil solution without the addition of carbonaceous materials. Nevertheless, leachability tests suggested that the provision of green waste compost and lignite augmented the simultaneous reduction of As and Cu leachability in a fairly aggressive leaching environment. These results highlight the importance of assessing stability and remobilisation of sequestered metals under varying environmental conditions for ensuring a plausible and enduring soil stabilisation.     

Investigations of ash topography/morphology and their relationship with heavy metals leachability

The leachability of heavy metals such as chromium (Cr), lead (Pb) and cadmium (Cd) from the ash material obtained from waste combustion was studied. The effects of ash surface topography and morphology on the leachability of these elements were examined using atomic force microscopy (AFM) and scanning electron microscopy (SEM). The AFM (scan size 10 x 10 microns) and SEM images of the simulated ash pellet obtained at various operating temperatures (1000, 1400 and 1500 degrees C) showed significant microstructural and topographical changes. Ash pellets treated at 1000 degrees C contain porous and non-continuous surface. On the other hand, the ash pellet obtained at higher temperature (1500 degrees C) was found to contain a smooth, continuous and non-porous surface. The AFM height profile studies indicated that the top surface variation of the ash pellet at 1000, 1400 and 1500 degrees C were found to be -40.0 to 25.5, -3.7 to 4.7 and -0.10 to 0.66 nm respectively. The SEM analyses also confirmed the presence of smooth, non-porous outer surface of ash formed at 1500 degrees C. In addition, it also showed the presence of compact and rigid interior for the same ash pellet. The leachability of the heavy metals was determined using standard toxicity characteristic leaching procedure (TCLP) test and the samples were analysed using atomic absorption spectroscopy. The results showed that the TCLP leaching ratios of the heavy metals were Cr = 0.30, Pb = 0.05 and Cd = 0.09 at 1000 degrees C. However, the ash obtained at 1400 degrees C showed negligible heavy metals leaching ratio while at 1500 degrees C no leachability was detected (TCLP concentration dropped to nondetectable levels). The use of high temperature treatment enabled the immobilization of heavy metals in the ash preventing their leaching. Such ash can be considered as a non-hazardous material for reuse or safe disposal.     

表面活性剂淋滤对土壤中邻苯二甲酸酯纵向迁移的影响

以无表面活性剂的去离子水为对照、设置1倍(1 CMC)和2倍临界胶束浓度(2 CMC)浓度,研究了单一和混合表面活性剂,包括十六烷基三甲基溴化铵(CTAB)、十二烷基苯磺酸钠(SDBS)和曲拉通X-100(TX-100)对人工污染土壤中邻苯二甲酸酯(PAEs)纵向迁移的影响,土柱中上层为PAEs污染土(3 cm),下层为清洁土(20 cm)。CTAB和SDBS在2 CMC时、TX-100为1 CMC时可增强污染土中PAEs的纵向迁移,其中DMP和DEP有无表面活性剂均可发生迁移,在相同表面活性剂条件下,延长老化时间对污染土中PAEs的迁移产生一定的影响。CTAB和SDBS在2 CMC时,清洁土中PAEs总含量较低,但TX-100在1 CMC时较低。清洁土中PAEs总含量均随土层深度的增加而降低。当老化时间较短时,土壤有机质对PAEs在清洁土柱的迁移影响较小,老化时间的延长对清洁土中的PAEs迁移影响较大。3种表面活性剂均可有效促进清洁土中DMP和DEP的迁移,CTAB和SDBS在2 CMC、TX-100在1 CMC时可促进DNBP和BBP的迁移,但3种表面活性剂对清洁土中DNOP迁移的影响较小。与单一表面活性剂相比,混合表面活性剂有助于污染土中PAEs的迁移,且随着浓度的升高,清洁土中PAEs的含量呈现降低的趋势。就整个土柱而言,单一表面活性剂CTAB和SDBS在较高浓度时、TX-100较低的浓度时对PAEs的淋滤效果更好;在较短老化时间下,土壤有机质含量的高低对淋滤率没有显著影响;老化时间延长有效降低了淋滤率;而混合表面活性剂的淋滤率有明显提高,更有助于PAEs的迁移。     

Leaching of brominated flame retardants in leachate from landfills in Japan

Leachate samples were taken from seven different landfills and concentrations of brominated flame retardants (BFRs), i.e. polybrominated diphenyl ethers (PBDEs) and tetrabromobisphenol A (TBBPA), were quantified. Leaching characteristics of BFRs, especially factors affecting leachability, were clarified to obtain basic information regarding the release of BFRs into the environment. The results obtained for observed levels of the sum of PBDE-47, -99 and -100 were n.d.--4000 pg/l for the raw leachate and n.d. for the treated one, respectively, and those of TBBPA were n.d.--620,000 pg/l for the raw leachate and n.d.--11,000 pg/l for the treated one, respectively. Three sites that not only had crushed material from bulk wastes such as waste electric and electronic equipment, but also were under operation or within a year since closure, indicated a higher concentration of BFRs than the other sites. In particular extremely high concentration of PBDEs was observed at a site with a large amount of organics. Considering the leaching characteristics of BFRs, there exists the possibility that leachability of PBDEs is influenced by the presence of dissolved humic matter (DHM) in the leachate. The high removal efficiency for BFRs in the leachate treatment process was also confirmed.     

Leaching characteristics of polycyclic aromatic hydrocarbons (PAHs) from spiked sandy soil

In order to evaluate the factors affecting leachability of hydrophobic organic pollutants (HOPs), we performed leaching tests under a variety of conditions using sandy soil contaminated with phenanthrene and pyrene. The results obtained were: (1) the shaking time, temperature, and dissolved humic matter (DHM, as coexisting matter) increased leachability; (2) ionic strength reduced leachability; and (3) the liquid-to-solid ratio and pH level had no effect on leaching concentration of HOPs. In DHM-added leaching tests assuming equilibrium with HOPs, DHM, and solid matrix, the partitioning (binding) coefficient of HOPs to DHM was accurately calculated with the equations proposed in this study. While we recommend taking into consideration the coexistence of DHM, it is difficult to use universally because its properties differ according to origin and extracting method. It is therefore reasonable to use an alternative reagent having an effect similar to that of DHM.     

Evaluation of the stability of arsenic immobilized by microbial sulfate reduction using TCLP extractions and long-term leaching techniques

An investigation was conducted to evaluate the stability or leachability of arsenic immobilized by microbial sulfate reduction. Anoxic solid-phase samples taken from a bioreactor previously used to treat metal and As contaminated water using sulfate reducing bacteria (SRB) were subjected to the toxicity characteristic leaching procedure (TCLP) and long-term column leaching tests. The results from TCLP experiments showed that the concentration of As leached from solid-phase sulfide material (SSM) samples after an 18 h extraction time was <300 microgl(-1), which is below the current maximum Australian TCLP leachate value for As, and thus would not be characterized as a hazardous waste. In terms of percent total As leached, this was equivalent to <8.5% for SSM samples initially containing 61.3 mgkg(-1) As. The levels of As extracted by the TCLP was found to be significantly lowered or underestimated in the presence of dissolved oxygen, with As concentrations increasing with decreasing headspace-to-leachant volume ratios. The concentration of As was also consistently higher in nitrogen purged extractions compared to those performed in air. This was attributed to the dissolution of Fe-sulfide precipitates and subsequent oxidation of Fe(II) ions and precipitation of ferric(hydr)oxides, resulting in the adsorption of soluble As and corresponding decrease in As concentrations. According to the experimental data, it is recommended that TCLP tests for As leachability should be performed at least in zero-headspace vessels or preferably under nitrogen to minimize the oxidation of Fe(II) to ferric(hydr)oxides. In long-term leaching studies (approximately 68 days), it was found that the low solubility of the SSM ensured that rate of release of As was relatively slow, and the resulting leachate concentrations of As were below the current Australian guideline concentration for arsenic in drinking water.     

Effect of dissolved humic matters on the leachability of PCDD/F from fly ash--laboratory experiment using Aldrich humic acid

The effect of dissolved humic matters (DHM) on the leachability of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/F) in fly ash was studied theoretically and in laboratorial condition to verify the previous results for pilot and field experiment of incineration residues landfill. In theoretical review, it was shown that DHM could influence the actual solubility and leachability of PCDD/F. The higher concentration of DHM showed the higher leachability of PCDD/F. In the leaching test, three different DHM concentrations and pHs of solutions were adopted to fly ash samples imaging the various characteristics of municipal solid waste leachate. It was proved experimentally that the leachability of PCDD/F increased with increasing DHM concentration in all pH conditions. The highest leachability was shown at the highest pH. Isomer distribution patterns of PCDD/F in all leachates were similar in all pH conditions. It backed up the distribution theory of PCDD/F between DHM and water.     

Leaching characteristics of polybrominated diphenyl ethers (PBDEs) from flame-retardant plastics

To investigate the effect of leachant on the leachability of polybrominated diphenyl ethers (PBDEs), we determined the leaching concentrations of PBDEs from flame-retardant plastic samples (TV housings and raw materials before molding processing) that are regarded as a source of PBDEs in landfill sites. The leachants used were distilled water, 20% methanol solution, and dissolved humic solution (DHS) of 1000 mg/l based on organic carbon. The leaching test conditions were a liquid-to-solid ratio of 100:1, and a contact period of five days, with twice-daily agitation in a temperature-controlled room of 30 degrees C without pH or ionic strength control. The leaching concentrations of PBDEs increased with increased content, and were found to be remarkably enhanced when methanol and DHS were used instead of distilled water. The enhancement of leachability in the presence of the latter was attributed to the cosolvency effect, and complex formations between the PBDEs and dissolved humic matter (DHM). PBDE concentrations in the leachate obtained from the leaching test and an actual landfill site revealed a significant presence of congeners below heptabromodiphenyl ethers (H7BDEs), detected in the leachate of the actual landfill, while significant amounts of nonabromodiphenyl ethers (N9BDEs) and decabromodiphenyl ether (D10BDE) were detected in the leachate of the leaching test.     

Quasi-dynamic leaching characteristics of polychlorinated dibenzo-p-dioxins and dibenzofurans from raw and solidified waste incineration residues

Quasi-dynamic leaching characteristics of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) from raw and solidified air pollution control (APC) residues were examined via a nine-time multiple leaching test. The effect of injected activated carbon in the APC residues on the PCDD/F leachability was also evaluated. When humic acid solution was used as a leachant, the leaching concentrations of PCDD/Fs fluctuated between the first and the fifth leaching, followed by a gradual increase and then suddenly reached maximum values at the leaching sequences around seventh and eighth. This significant enhancement in PCDD/F leachability was mainly due to an increase in the release of highly chlorinated PCDD/Fs. Leaching of PCDD/Fs with n-hexane was, in contrast, primarily caused by the partitioning of hydrophobic PCDD/Fs between the APC residue surface and the liquid phase of n-hexane. Consequently, the largest leaching concentrations for n-hexane tests achieved at the first leaching, followed by a decrease and reached plateaus. Solidification/stabilization (S/S) decreased the PCDD/F leachability up to the fifth leaching by the use of humic acid solution. However, S/S increased the PCDD/F leaching concentrations and rates with n-hexane. The activated carbon in APC residues significantly inhibited the release of PCDD/F with n-hexane. The inhibiting effect provided by activated carbon was, however, less significant by the use of humic acid solution.     

Leaching behavior of Cr(III) in stabilized/solidified soil

The leaching behavior of chromium was studied using batch leaching tests, surface complexation modeling and X-ray absorption near edge structure (XANES) spectroscopy. A contaminated soil sample containing 1330 mg-Cr kg(-1) and 25600 mg-Fe kg(-1) of dry soil was stabilized/solidified (S/S) with 10% cement, 25% cement, 10% lime and a mixture of 20% flyash and 5% lime. The XANES analysis showed that Cr(III) was the only Cr species in untreated soil and S/S-treated samples. The leachate Cr concentration determined using the toxicity characteristic leaching procedure (TCLP) was reduced from 5.18 mg l(-1) for untreated soil to 0.84 mg l(-1) for the sample treated with 25% cement. The Cr leachability in untreated and treated soil samples decreased dramatically as the pH increased from 3 to 5, remained at similar levels in the pH range between 5 and 10.5, and further decreased at pH>10.5. Modeling results indicated that the release of Cr(III) was controlled by adsorption on iron oxides at pH<10.5, and by precipitation of Ca(2)Cr(2)O(5).6H(2)O at pH>10.5.     

Immobilization of lead in contaminated firing range soil using biochar

Soybean stover-derived biochar was used to immobilize lead (Pb) in military firing range soil at a mass application rate of 0 to 20 wt.% and a curing period of 7 days. The toxicity characteristic leaching procedure (TCLP) was performed to evaluate the effectiveness of the treatment. The mechanism responsible for Pb immobilization in military firing range soil was evaluated by scanning electron microscopy-energy dispersive x-ray spectroscopy (SEM-EDX) and x-ray absorption fine structure (XAFS) spectroscopy analyses. The treatment results showed that TCLP Pb leachability decreased with increasing biochar content. A reduction of over 90 % in Pb leachability was achieved upon treatment with 20 wt.% soybean stover-derived biochar. SEM-EDX, elemental dot mapping and XAFS results in conjunction with TCLP leachability revealed that effective Pb immobilization was probably associated with the pozzolanic reaction products, chloropyromorphite and Pb-phosphate. The results of this study demonstrated that soybean stover-derived biochar was effective in immobilizing Pb in contaminated firing range soil.     

Biodegradation of phenanthrene in soil.

We investigated the potential of an aerobic polycyclic aromatic hydrocarbon (PAH)-adapted consortium to degrade phenanthrene in soil. Optimal degradation conditions were determined as pH7.0 and 30 degrees C with a water content of 100% wt soil/wt water (w/w). At a concentration of 5 microg/g, phenanthrene degradation (k1) was measured at 0.0269 l/hr with a half-life (t(1/2)) of 25.8 hrs. Our results show that the higher the phenanthrene concentration, the slower the degradation rates. Phenanthrene degradation was enhanced by treatment with yeast extract, glucose, or pyruvate, but was not significantly improved by the addition of acetate. Degradation was delayed by the addition of either compost or potassium nitrate and enhanced by the addition of nonionic surfactants (Brij30, Brij35, Triton X100 or Triton N101) at critical micelle concentration (CMC). Phenanthrene degradation was delayed at levels above CMC.     

Effect of calcite on Pb-doped solidified waste forms in leaching

The alkalinity of cementitious materials rectifies a low pH of leachant to be over 12 in leaching. The rapid change of leachant pH produces the remarked variation of solubility of heavy metals in the toxicity characteristic leaching procedure. The release of lead on cementitious solid waste forms in leaching was observed in the pH range of particularly 12. The release of lead is significant dependant on the changed values of leachant pH. The pH static leaching procedure (PSLP) was implemented for assessing a quantitative measurement of total potential leachability with the continuing addition of acidic leachant up to the point of no change of leachant pH. The release of lead on Pb-doped solidified waste forms (SWF), in the PSLP, was 27.0% of initial concentration at the maximum meq CH₃COOH (about 24.0) added to g dry solidified wastes. In this study, the immobilization effect of calcite on SWF was investigated in the acidic condition by the PSLP. Calcite additions to SWF make a good fixation efficiency of about 92%. Calcite addition abundantly provides the acid neutralization capacity to protect SWF from the attack of acid, with the marked development of hydrated minerals (mainly portlandite and C–S–H) in accordance with the accelerating effect of cement hydration.     

Solubility and adsorption behaviors of chlorpyriphos-methyl in the presence of surfactants

In the present work changes in the adsorption of the pesticide chlorpyrifos-methyl (CLP-m) on soil colloids induced by application of surfactants were determined using a batch equilibrium method. The surfactants used were sodium dodecyl sulphate (SDS), Tween 20, and dihexadecyldimethylammonium bromide (DHAB). The adsorption isotherms of CLP-m in aqueous medium and in surfactant solutions at concentration equal to the critical micelle concentration (CMC) fitted the Freunlich adsorption equation generally with R² values greater than 0.96. While the addition of SDS and DHAB decreased the pesticide adsorption, the addition of Tween 20 increased the pesticide adsorption. The increases or decreases in the adsorption in the experiment revealed that the behavior of CLP-m in soil water-systems mainly depends on the type of surfactant. Moreover water solubility of CLP-m changes by the three surfactants below and above their CMC were studied. While the solubility of CLP-m was enhanced by SDS both below and above the CMC, the solubility of the pesticide was enhanced by DHAB only above the CMC. Tween 20 did not influence the solubility of CLP-m.     

Stabilization and Solidification of Metal-Laden Wastes by Compaction and Magnesium Phosphate-Based Binder

ABSTRACT

Bench-scale and full-scale investigations of waste stabilization and volume reduction were conducted using spiked soil and ash wastes containing heavy metals such as Cd, Cr, Pb, Ni, and Hg. The waste streams were stabilized and solidified using chemically bonded phosphate ceramic (CBPC) binder, and then compacted by either uniaxial or harmonic press for volume reduction. The physical properties of the final waste forms were determined by measuring volume reduction, density, porosity, and compressive strength. The leachability of heavy metals in the final waste forms was determined by a toxicity characteristic leaching procedure (TCLP) test and a 90-day immersion test (ANS 16.1). The structural composition and nature of waste forms were determined by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively.

CBPC binder and compaction can achieve 80-wt % waste loading and 39-47% reduction in waste volume. Compressive strength of final waste forms ranged from 1500 to 2000 psi. TCLP testing of waste forms showed that all heavy metals except Hg passed the TCLP limits using the phosphate-based binder. When Na₂S was added to the binder, the waste forms also passed TCLP limits for Hg. Long-term leachability resistance of the final waste forms was achieved for all metals in both soil and ash wastes, and the leachability index was ~14. XRD patterns of waste forms indicated vermiculite in the ash waste was chemically incorporated into the CBPC matrix. SEM showed that waste forms are layered when compacted by uniaxial press and are homogeneous when compacted by harmonic press.     

Stabilization and solidification of metal-laden wastes by compaction and magnesium phosphate-based binder

Bench-scale and full-scale investigations of waste stabilization and volume reduction were conducted using spiked soil and ash wastes containing heavy metals such as Cd, Cr, Pb, Ni, and Hg. The waste streams were stabilized and solidified using chemically bonded phosphate ceramic (CBPC) binder, and then compacted by either uniaxial or harmonic press for volume reduction. The physical properties of the final waste forms were determined by measuring volume reduction, density, porosity, and compressive strength. The leachability of heavy metals in the final waste forms was determined by a toxicity characteristic leaching procedure (TCLP) test and a 90-day immersion test (ANS 16.1). The structural composition and nature of waste forms were determined by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. CBPC binder and compaction can achieve 80-wt% waste loading and 39-47% reduction in waste volume. Compressive strength of final waste forms ranged from 1500 to 2000 psi. TCLP testing of waste forms showed that all heavy metals except Hg passed the TCLP limits using the phosphate-based binder. When Na2S was added to the binder, the waste forms also passed TCLP limits for Hg. Long-term leachability resistance of the final waste forms was achieved for all metals in both soil and ash wastes, and the leachability index was approximately 14. XRD patterns of waste forms indicated vermiculite in the ash waste was chemically incorporated into the CBPC matrix. SEM showed that waste forms are layered when compacted by uniaxial press and are homogeneous when compacted by harmonic press.     

Evaluation of the leachability of polychlorinated dibenzo-p-dioxins and dibenzofurans in raw and solidified air pollution control residues from municipal waste incinerators

Leachability of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) from raw and solidified air pollution control (APC) residues with selected solvents, including acetic acid, simulated acid rain, humic acid, linear alkylbenzene sulfonate (LAS) and n-hexane was investigated. High-chlorinated PCDD/F congeners were observed in all leachates of raw APC residue samples, with the largest total leaching concentration (61.60 ngm(-3); 0.30 ngI-TEQm(-3)) from treatment with humic acid. Low-chlorinated congeners were mainly leached with LAS and n-hexane. Solidification and stabilization (S/S) processes with cement and sulfur-containing chelating agent decreased the leachability of PCDD/Fs by up to 98% with humic acid and LAS as solvents. However, S/S processes enhanced the leachability of both high- and low-chlorinated PCDD/F congeners with n-hexane as the solvent, which largely increased the toxic equivalent quantity of leachates. These results suggest that conventional S/S processes may effectively restrain the release of PCDD/Fs when APC residues are leached with rain water or natural organic compounds (e.g., humic acid), but may have a deteriorated effect when APC residues are leached with nonpolar organic solvents (e.g., n-hexane) coexisting in the landfill sites.     

Fractionation and mobility of metals in bauxite red mud

Red mud (RM) is a strongly alkaline residue generated in enormous amounts worldwide from bauxite refining using the Bayer chemical process. RM is composed mainly of Fe, Ti and Al oxides and hydroxides, but it also contains an array of trace metals and metalloids at different concentrations. The purpose of this paper is to assess the potential mobility of metals in RM, with special emphasis on pH effect. The ‘operational’ distribution and leachability of metals within/from RM was studied by applying a sequential extraction procedure (SEP) and several leaching tests (rapid titration, equilibration acidification, batch leaching with acetic acid and also the toxicity characteristics leaching procedure (TCLP) and the DIN 38414-S4 procedures, used as reference methods) carried out at different pH, solid/liquid ratio, extraction period and type of acid (HCl or acetic acid). Chemical analysis showed that, in addition to the major metals Fe, Al and Ti, RM contains several trace metals, some of them (Cr, Cu and Ni) in concentrations exceeding the regulatory limits. SEP showed that a majority of the metals in the RM (between the 32.2?±?8.5 for Cd and 95.3?±?0.4 % for Ni) were found in the residual fraction, suggesting that they are not readily mobile under normal environmental conditions. Leaching tests performed at different pH showed that a significant fraction of the metals is mobilised from RM only under very strong acid conditions (pH?<?2), whereas Al is released in considerable amounts at pH?<?5.3. Among the trace metals, Cr requires special attention because of its relative high concentration in RM and the higher concentrations of this metal mobilised at low pH. The leaching tests using acetic acid showed that the standard TCLP largely underestimates the release of trace metals from RM, and therefore it is not advisable to evaluate the actual potential leaching of trace metals from this residue.