木屑和花生壳吸附去除水溶液中Cr^3＋的试验研究

以废弃物木屑和花生壳作为吸附剂，进行了吸附去除水中Cr^3＋的试验。研究了溶液pH值、初始Cr^3＋浓度以及温度等因素对这2种吸附剂去除Cr^3＋作用的影响，对吸附曲线作了线性拟合，确定了相应的平衡吸附率，在Cr^3＋初始浓度为1、5、10和20mg／L时，木屑对Cr^3＋的平衡吸附率为81％、68％、56％和40％，花生壳依次为77％、63％、53％和42％，并探讨了这2种吸附剂对溶液中Cr^3＋的吸附机理。     

花生壳、大豆壳和柚子皮对Cr3+、Cu2+和Ni2+的吸附研究

采用农林废弃物花生壳、大豆壳、柚子皮对重金属离子Cr3+、Cu2+和Ni2+进行吸附研究,探讨反应时间、吸附剂用量、pH、重金属离子初始浓度以及温度对吸附的影响.结果表明:柚子皮对Cr3+、Cu2+、Ni2+的吸附效果优于花生壳和大豆壳,其在20℃、pH 5.00、10.0 mg/kg条件下,反应360 min,Cr3+、Cu2+、Ni2+的吸附率分别可达83.20％、84.50％、59.10％;花生壳、大豆壳和柚子皮对Ni2+的吸附率远低于Cr3+和Cu2+；花生壳、大豆壳和柚子皮对Cr3+、Cu2+、Ni2+的吸附动力学可以用准二级动力学方程描述；吸附率随初始重金属离子浓度增加而降低,其吸附等温线可以用Langmuir方程描述；在一定范围内,吸附率随吸附剂用量增加而增加；溶液初始pH在2～5时,吸附率随pH增大而增加；Cu2、Ni2+的吸附量随温度的上升而逐渐减少,但Cr3+的吸附量随着温度的上升而略增加.     

NiFe_2O_4/ZnAl-LDH吸附去除水中Cr(Ⅵ)

采用共沉淀法合成磁性复合材料NiFe_2O_4/ZnAl-LDH,通过静态吸附试验考察复合材料去除水中Cr(VI)的性能,系统地研究了溶液初始p H值、吸附剂投加量、吸附时间和温度等因素对Cr(VI)去除效果的影响。结果表明,当溶液初始p H值为2、初始Cr(VI)浓度为50 mg·L-1、吸附剂投加量为4 g·L-1时,吸附过程在240 min内达到平衡,此时Cr(VI)的去除率为89.5%。动力学和吸附等温式的研究表明:NiFe_2O_4/ZnAl-LDH吸附Cr(VI)的过程符合准二级动力学和Langmuir等温吸附模型。热力学参数表明该吸附过程为自发、放热的反应过程,低温有利于吸附剂对Cr(VI)的吸附。吸附剂经4次再生后对Cr(VI)仍有83.1%的去除率,且其在外加磁场的作用下能快速与水溶液分离,因此NiFe_2O_4/ZnAl-LDH可作为去除水中Cr(VI)的良好吸附剂。     

高比表面积活性炭的制备及对Cr(Ⅵ)吸附的研究

以椰树壳为原料,运用水蒸汽和二氧化碳复合物理活化法在4 h内制备了2 162.84 m2/g的高比表面积活性炭,其孔径分布范围为1.1~2.5 nm。应用此吸附剂考察了溶液pH、吸附剂用量、接触时间和初始浓度对Cr(VI)离子吸附效果的影响,并讨论了固定吸附床中不同溶液流量对Cr(VI)去除效果的影响。结果表明:在温度为298 K、溶液pH为1.96、吸附剂用量为0.10 g、铬离子初始浓度为100 mg/L与接触时间为70 min的条件下,活性炭对铬离子具有较高的吸附容量,去除率高达99.32%;铬离子在吸附床中的穿透曲线具有陡峭的传质锋面,但随着铬离子溶液流量的增大脱除果率降低。     

花生壳活性炭对水溶液中Cr(Ⅵ)的吸附性能

为提高花生壳对Cr(Ⅵ)的吸附性能,采用ZnCl2对花生壳进行改性,制得花生壳活性炭。通过批次吸附实验,考察了花生壳活性炭投加量、pH值、吸附时间等因素对Cr(Ⅵ)的吸附性能影响,同时,对吸附动力学、等温吸附特征和热力学进行了系统研究。结果表明,当吸附剂投加量为0.2 g时,在Cr(VI)初始浓度为20 mg/L、pH值为2.0条件下,吸附反应180 min后,花生壳活性炭对Cr(Ⅵ)的吸附率可维持在94.13%以上。吸附过程符合准二级动力学方程和Langmuir等温吸附模型;由吸附热力学方程计算得到吸附焓变(ΔH)>0,吸附自由能变(ΔG)<0,吸附熵变(ΔS)>0,表明花生壳活性炭对Cr(Ⅵ)的吸附过程是吸热和自发的。     

改性玉米秸秆炭和花生壳炭对溶液中Cd~(2+)的吸附

对玉米秸秆和花生壳炭化制备的生物炭,运用高锰酸钾进行改性,研究其对Cd~(2+)的吸附效果。通过批次吸附实验,考察了两种改性生物炭对Cd~(2+)吸附的初始浓度、pH值、接触时间等因素的影响。结果表明,在pH为6.0,Cd~(2+)浓度为100 mg·L~(-1),温度为20℃,吸附时间为12 h,吸附剂投加量为1.0 g·L~(-1)条件下,改性玉米秸秆炭和花生壳炭对Cd~(2+)的去除率分别为67.03%和46.10%,与未改性的生物炭相比,吸附率分别提高了3.8倍和6.2倍。改性玉米秸秆炭和花生壳炭对溶液中Cd~(2+)的吸附均符合Langmuir和Freundlich等温吸附模型,最大吸附量分别为68.97和55.55 mg·g-1。两种改性生物炭的吸附行为均符合准二级吸附动力学模型,说明其吸附以化学吸附为主。改性玉米秸秆炭和花生壳炭吸附Cd~(2+)后,可用NaOH溶液进行解吸,解吸4次后,对Cd~(2+)仍有较好的吸附效果,吸附量分别为31.40和24.10 mg·g~(-1)。这说明,高锰酸钾改性玉米秸秆炭和花生壳炭是一种吸附性能高且能够重复利用的去除溶液中Cd~(2+)的吸附材料。     

改性花生壳对四环素类抗生素的吸附特性研究

针对养殖业受抗生素污染水体,以花生壳为原料、NaOH为改性剂制备吸附剂,选择有代表性的3种四环素类抗生素(土霉素、四环素和强力霉素)进行静态吸附实验,考察吸附时间、初始浓度、pH、阳离子强度对吸附性能的影响.结果表明,改性花生壳对3种抗生素的吸附在12h时基本达到平衡,该吸附过程能够较好地被准二级动力学模型和Langmuir等温吸附模型拟合.当pH由2升高至10时,抗生素吸附量先增加后减少,在pH为5～7时吸附效果尤为显著.共存阳离子的存在影响吸附效果,随着Ca2+浓度的升高,改性花生壳对3种抗生素的吸附作用逐渐减弱.     

非活体生物质对水中活性艳红X-3B的吸附研究

研究了4种非活体生物质(米酒糟、花生壳、柚子皮、稻草秸秆)对模拟废水中活性艳红X-3B的吸附条件及吸附机理。结果表明,活性艳红X-3B初始浓度为100 mg/L、pH为1.0~2.0、吸附剂浓度为10 mg/L时,4种吸附剂对活性艳红X-3B的吸附率可达到80%。吸附在60 min左右达平衡后最大吸附量的顺序为:米酒糟(58.8 mg/g)花生壳(28.0mg/g)柚子皮(23.6 mg/g)稻草秸秆(19.5 mg/g)。在达最大吸附率时,米酒糟的用量可减少一半、pH范围可宽为1.0~6.0,且吸附量是另三者的2倍以上。综合比较,米酒糟具有较强的吸附废水中活性艳红X-3B的能力,可作为废水中活性染料的吸附剂使用。而花生壳、柚子皮和稻草秸秆的吸附能力相对较弱,不是理想的吸附材料。数学模型模拟表明,米酒糟和柚子皮的吸附过程更符合Freundlich方程,而花生壳和稻草秸秆更符合Langmuir方程;动力学研究表明4种吸附剂的吸附拟合更符合拟二级动力学方程。     

米糠生物质解毒含铬(Ⅵ)水溶液的研究

农林生物质是一种成本低、环境友好的重金属废水处理材料,也是受重金属污染环境的修复材料之一.实验讨论了初始pH值、米糠用量、吸附时间对含铬(Ⅵ)水溶液解毒的影响.结果表明,米糠对Cr(Ⅵ)存在吸附作用,同时也有解毒还原能力.100 mL浓度为100 mg/L的含铬溶液,在初始pH为2、米糠用量为3 g、吸附-反应平衡时间7 h的条件下,生物质吸附去除溶液中的铬为14.4%,而原溶液中Cr(Ⅵ)解毒了57.2%,米糠生物质吸附总铬的能力为0.48 mg Cr/g(生物质).米糠生物质有潜在的吸附铬和修复受铬污染环境的利用价值.     

碳羟基磷灰石对水中Cr(Ⅵ)的吸附性能研究

利用废弃蛋壳为原材料,水热法合成碳羟基磷灰石(CHAP),并利用X射线衍射、扫描电镜、能谱分析手段对其结构进行了表征.将CHAP作为含铬废水的吸附剂,考察了pH、Cr(Ⅵ)初始浓度、吸附时间等对Cr(Ⅵ)吸附行为的影响.结果表明,初始质量浓度为50 mg/L的Cr(Ⅵ)溶液,在常温(22±2) ℃、溶液pH为3.0、CHAP用量为5 g/L时,30 min基本达到吸附平衡,Cr(Ⅵ)去除率为98.3%,饱和吸附容量达29.85 mg/g.CHAP对Cr(Ⅵ)的吸附行为符合Langmuir吸附等温式和Freundlich吸附等温式,相关系数分别为0.998 4和0.922 6.通过10%(体积分数)H2SO4对吸附Cr(Ⅵ)的CHAP进行再生,再生率最高达95.8%.     

超细粉煤灰基成型吸附剂的动态吸附实验

以粉煤灰为原料制备成型吸附剂，对水溶液中亚甲基蓝和Cr⁶⁺进行动态吸附研究，绘制穿透曲线，利用Origin软件对实验数据分析处理，得出穿透曲线的通式C_t=A₁－A₂〖〗1+(t/t₀)^p+A₁。结果表明，初始浓度C₀=25 mg/L，填料高度不同时，达到穿透点的时间随填料高度的增加而增加；填料高度h=200 mm，初始浓度不同时，达到穿透点的时间随初始浓度的增加而减小；该吸附剂对有机染料和重金属离子均有较好的吸附性能；穿透曲线通式的回归线性相关系数表明，该通式可很好地反映超细粉煤灰成型吸附剂的动态吸附过程。     

Arsenic(III) removal by adsorption on sawdust carbon

Studies on the removal of As(III) by adsorption on sawdust and sawdust carbon have been carried out at room temperature (25 ± 1°C). The adsorption isotherm of As(III) on sawdust carbon was obtained in a batch reactor. The process of uptake follows the first-order adsorption rate expression and obeys the Langmuir and Freundlich model of adsorption. The mass transfer coefficients as a function of initial sorbate concentration have been determined. Parameters such as pH and absorbent dose were studied. Maximum adsorption capacity was observed at pH 7.0.     

BM二代菌去除电镀废水中重金属离子的效果研究

BM菌是一种能够高效去除电镀废水中重金属离子的新型功能菌群,实验研究了BM二代菌对Cr6+、Ni2+的最佳去除条件,结果表明:当水温为10~30℃,pH=2,Cr6+浓度为100 mg/L,反应10 min,菌废比为1∶200时废水中Cr6+的去除率达到98%以上;当水温为10~30℃,pH=8.5,Ni2+浓度为100 mg/L,反应10 min,菌废比为1∶200时废水中Ni2+的去除率达到96%以上;在相同条件下实际电镀废水中Cr6+和Ni2+的去除率均高于99%。     

微波法处理含铬废渣的可行性分析

微波辐照解毒铬渣是一项新技术,为考察该技术应用的可行性,本文对铬渣解毒前后性状的变化进行了讨论。结果表明,该技术能较完全地使高价铬转化为低价铬,解毒渣中铬主要以三价形态存在,铬渣毒性得到消除;解毒渣浸出液中Cr6+浓度远低于国家危险废物鉴别标准,解毒渣已不属于危险固体废弃物,其在环境条件下可安全存放。说明该技术具有应用前景。     

松树锯末对亚甲基蓝（MB）的吸附研究

采用松树锯末以及改性松树锯末对模拟废水中的亚甲基蓝进行吸附实验研究。研究结果表明，当亚甲基蓝的初始浓度为50 mg/L、pH为6、锯末投加量为1 g/L时，改性前后的锯末对亚甲基蓝的吸附量最大，分别为29.9 mg/g和60.6 mg/g。同时，对改性前后的锯末做了吸附等温线拟合及动力学研究。结果表明，吸附等温线均能很好地符合Langmuir吸附模式，吸附过程符合拟二级动力学方程。     

木屑黄原酸盐对双离子体系中铜镍的吸附

利用木屑制备木屑黄原酸盐吸附剂,对其进行FTIR、XRD和BET分析,并考察了对双离子体系中铜镍离子的吸附情况,重点研究了木屑黄原酸盐吸附量的预测和吸附初始速率的计算。结果表明,在铜镍双离子体系中,利用扩展的Langmuir模型能很好地预测木屑黄原酸盐对铜镍离子的吸附;吸附之初,吸附速率很快,并且随着干扰离子的浓度增大,所考察离子的初始速率逐渐减小。吸附情况说明,木屑黄原酸盐是一种具有良好吸附性能的吸附材料。     

Effect of DDT on plant mineral nutrition

DDT added to soil at a concentration of 50 microg g(-1) had no inhibitory effects on germination and plant growth of barley, mung and rice, but considerably inhibited the oilseed species tested in the laboratory. The uptake of one or other ions was affected in varying degrees, with plants grown in DDT-treated soils. Detailed field studies of a peanut crop further confirmed the inhibition of ion uptake with DDT, especially Ca(2+) and K(+). Reduced uptake of (86)Rb by germinated peanut seeds in the presence of DDT further supported the observations made with K(+). Cell number and length in plants were reduced in plants grown in DDT-treated soil and the role of calcium is discussed. It appears that growth inhibition in oil seed plants may arise from the low levels of Ca(2+) and K(+) in plants grown in DDT-treated soils.     

Eu3+ uptake by calcite: preliminary results from coprecipitation experiments and observations with surface-sensitive techniques

A lack of information in databases for contamination risk assessment about the transport behaviour of the trivalent f-orbital elements in groundwater systems where calcite is at equilibrium motivated this study of Eu(3+) uptake. The free drift technique was used to examine the effects of Eu(3+) concentration, presence of Na(+) or K(+) and temperature, as well as calcite nucleation and precipitation kinetics, on the partitioning of calcite. Changes in surface composition and morphology resulting from exposure of single crystals of Iceland spar to Eu(3+)-bearing solutions were observed with X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). First results confirm that calcite has high affinity for Eu(3+). Rates of nucleation and precipitation strongly affect the extent of uptake but the presence of Na(+) and K(+) has no effect, suggesting formation of solid solution as CaCO(3)-EuOHCO(3). Surface-sensitive techniques prove that Eu(3+) is adsorbed to calcite even when the surface is dissolving and adsorption is not accompanied by precipitation of a separate Eu(3+)-solid phase. Adsorbed Eu modifies calcite's dissolution behaviour, roughening terraces and rounding step edges, and producing surface morphology where some surface sites appear blocked. Results imply that Eu(3+) concentrations in natural calcites are limited by Eu(3+) availability rather than by a lack of ability to fit into calcite's atomic structure. This behaviour can probably be expected for other trivalent rare Earth elements (REE), actinides and fission products whose behaviour is similar to that of Eu(3+). These elements are likely to be incorporated within the calcite bulk in systems where it is precipitating and the demonstrated strong partitioning ensures some uptake even where calcite is at or under saturation.     

Adsorption characteristics of 2,4-dichlorophenoxyacetic acid (2,4-D) from aqueous solution on powdered activated carbon

The removal of 2,4-dichlorophenoxyacetic acid (2,4-D), one of the most commonly used phenoxy acid herbicides, from aqueous solution was studied by using acid-washed powdered activated carbon (PAC) as an adsorbent in a batch system. Adsorption equilibrium, kinetics, and thermodynamics were investigated as a function of initial pH, temperature, and initial 2,4-D concentration. Powdered activated carbon exhibited the highest 2,4-D uptake capacity of 333.3 mg g(-1) at 25 degrees C and an initial pH value of 2.0. Freundlich, Langmuir, and Redlich-Peterson isotherm models were used to express the equilibrium data of 2,4-D depending on temperature. Equilibrium data fitted very well to the Freundlich equilibrium model in the studied concentration range of 2,4-D at all the temperatures studied. Three simplified models including pseudo-first-order, pseudo-second-order, and saturation-type kinetic models were used to test the adsorption kinetics. It was shown that the adsorption of 2,4-D on PAC at 25, 35, and 45 degrees C could be best fitted by the saturation-type kinetic model with film and intraparticle diffusions being the essential rate-controlling steps. The activation energy of adsorption (EA) was determined as--1.69 kJ mole(-1). Using the thermodynamic equilibrium coefficients obtained at different temperatures, the thermodynamic constants of adsorption (deltaG degrees, deltaH degrees, and deltaS degrees) were also evaluated.     

饮用水源突发性铬污染去除方法的比较研究

通过对水源水中铬污染的不同去除方法的比较实验及验证实验,研究pH值、FeSO_4、NaHSO_3和活性炭的投加量对铬的去除效果的影响。实验结果表明,当原水中铬的含量为0.5 mg/L时,未调节pH值的条件下,亚硫酸氢钠与活性炭对铬的最高去除率为50%左右;硫酸亚铁还原沉淀在FeSO_4·7H_2O:Cr~(6+)投加比=16:1时,滤后出水中Cr~(6+)的去除率达到96.8%,中试出水中未检出Cr~(6+),出水的总Cr、总Fe等指标完全达到《生活饮用水卫生标准》(GB 5749-2006)的要求。