高效液相色谱-串联质谱法测定鱼胆汁中内分泌干扰物

采用固相萃取法富集鱼胆汁中5种环境内分泌干扰物(EDCs),用高效液相色谱-串联质谱法测定。通过试验优化前处理条件,使方法在0.100μg/L~500μg/L范围内线性良好,方法检出限为0.54 ng/L~6.41 ng/L。去离子水3个质量浓度水平的加标回收率为77.2%~98.3%,6次测定结果的RSD为2.1%~4.9%。空白鱼胆汁样品的中质量浓度加标回收率为81.7%~108%,6次测定结果的RSD为3.9%~7.1%。     

超高效液相色谱-串联质谱法测定土壤中多种全氟化合物

采用超声提取、固相萃取法处理土壤,用超高效液相色谱-电喷雾串联三重四极杆质谱测定样品中11种全氟化合物,通过优化测定条件,使方法在0.100μg/L~150μg/L范围内线性良好(r~20.995)。当取样量为2.0 g时,方法检出限为0.1 ng/g~0.4 ng/g。实际土壤样品的加标回收率为67.2%~106%,测定6次结果的RSD为6.6%~17.3%。     

超高效液相色谱-串联质谱法分析土壤及沉积物中氨基甲酸酯农药

利用超高效液相色谱-串联质谱,建立土壤和沉积物中痕量氨基甲酸酯农药的分析方法。该方法用体积比1:1的二氯甲烷/甲醇对土壤和沉积物样品进行加速溶剂萃取,GCB/PSA固相萃取小柱对萃取液进行净化,内标法定量,用超高效液相色谱-串联质谱法分析土壤和沉积物中20种氨基甲酸酯农药。20种氨基甲酸酯农药在0.02~1.0 μg/mL范围内线性良好(r≥0.99),检测限为0.20~0.60 ng/g。沉积物加标样品(20ng/g)和土壤加标样品(20ng/g)的回收率分别为33.2%~101.9%、38.8%~120.5%,相对标准偏差为6.1%~28.0%、2.3%~16.0%。沉积物加标样品(2.0 ng/g)回收率为43.0%~100.0%,相对标准偏差为2.1%~11.3%。     

SPE-GC-MS/MS法测定水源水中多种有机氯EDCs

采用C 18柱固相萃取(SPE)-三重四级杆气相色谱-质谱法同时测定水中18种含有机氯的环境内分泌干扰物,方法在0.500μg/L^100μg/L范围内线性良好,方法检出限为0.04 ng/L^0.8 ng/L,空白水样的加标回收率为61.3%~108%,6次测定结果的RSD为3.8%~18.0%。将该方法用于饮用水源水监测,18种目标化合物的测定值为未检出~1.5 ng/L,平均加标回收率为71.9%~109%,平行测定结果的RSD<15%。     

固相萃取-高效液相色谱法测定水中微囊藻毒素质量控制指标研究

采用固相萃取－液相色谱法，通过统计全国多家实验室的测定数据，对水中微囊藻毒素测试的平行样测定相对偏差、空白加标回收率、实际样品加标回收率、空白加标回收率平行样相对偏差以及样品加标回收率平行样相对偏差5个质控指标进行了研究，并给出了质控指标评价标准，提出在概率P和γ均为0.90时，其平行样测定允许最大相对偏差应控制在7.3%；空白加标质量浓度为0.005~20 μg/L时，回收率的控制范围为61%~125%；样品测定浓度为未检出、加标质量浓度在0.2~3.6 μg/L时，实际样品加标回收率控制范围为66%~108%；空白加标、样品加标回收率平行样最大相对偏差应分别控制在3.9%和8.9%。在概率P和γ均为0.95时，其平行样测定允许最大相对偏差应控制在8.3%；空白加标质量浓度为0.005~20 μg/L时，回收率的控制范围为49%~137%；样品测定浓度为未检出、加标质量浓度在0.2~3.6 μg/L时，实际样品加标回收率控制范围为60%~114%；空白加标、样品加标回收率平行样最大相对偏差应分别控制在5.2% 和14.8%。     

快速溶剂萃取-气相色谱-串联质谱法测定底泥中的有机氯农药

采用快速溶剂萃取、中性硅胶-中性氧化铝复合柱对底泥样品进行提取和净化,采用气相色谱-串联质谱法测定底泥中的30种有机氯农药。该方法的检测限为0.01~0.05 μg/kg,加标回收率为80.6%~110.5%,样品重复测定6次,均能得到较好的精密度,其相对标准偏差小于20%。结果证明,该方法灵敏度高、重复性好、准确度高、且快速简便,完全满足底泥中有机氯农药的测定要求。     

砷铈催化分光光度法测定土壤中的碘

用碱灰化处理试样,采用砷铈催化分光光度法测定土壤中的碘,讨论了温度与时间对测定的影响。方法在0 ng~250 ng范围内线性良好,检出限为2.58μg/kg,土壤样品测定的RSD≤2.9%,加标回收率为78.0%~116%。     

吹扫捕集- GC/MS法测定水中卤代烃的质量控制指标研究

采用吹扫捕集-气相色谱/质谱联用法,通过实际样品测试及全国多家实验室测定数据统计两种方法,针对水中三氯甲烷、四氯化碳、溴仿、二氯甲烷、1,2-二氯乙烷、1,1-二氯乙烯、三氯乙烯、四氯乙烯等8种卤代烃的平行样测定相对偏差、空白加标回收率及实际样品加标回收率等3个指标,研究了每种卤代烃的质控指标评价标准,提出其平行样测定...     

固相萃取-高效液相色谱法测定河水中的多环芳烃

采用固相萃取富集河水样品中15种多环芳烃(PAHs),并用高效液相色谱法测定,通过优化萃取条件和仪器条件,使该方法在10.0μg/L~500μg/L范围内线性良好,相关系数R20.99。方法检出限为3.70 ng/L~27.2 ng/L,标准溶液平行测定7次RSD在10%以内,空白水样的加标回收率为39.3%~109%。     

固相萃取-UPLC-MS/MS法测定水中全氟化合物

水样中全氟辛酸、全氟辛烷磺酸钾、全氟丁酸、全氟丁烷磺酸经弱阴离子交换固相萃取柱富集净化后,用超高效液相色谱-串联质谱法测定。通过优化样品前处理条件和仪器条件,使4种全氟化合物在0.05μg/L~10.0μg/L范围内线性良好,相关系数为0.998 9~0.999 9,方法检出限为0.27 ng/L~0.96 ng/L。空白水样3个质量浓度水平的加标回收率为73.1%~91.3%,6次测定结果的RSD为7.4%~14.3%。     

A New Mathematical Approach in Environmental and Life Sciences: Gene–Environment Networks and Their Dynamics

An important research area in life sciences is devoted to modeling, prediction, and dynamics of gene-expression patterns. As clearly understood in these days, this enterprise cannot become satisfactory without acknowledging the role of the environment. To a representation of past, present, and most likely future states, we also encounter measurement errors and uncertainties. This paper surveys and improves recent advances in understanding the foundations and interdisciplinary implications of the newly introduced gene–environment networks, and it integrates the important theme of carbon dioxide emission reduction into the networks and dynamics. We also introduce some operational and managerial issues of practical working and decision making, expressed in terms of sliding windows, quadrants (modules) of parametric effects, and navigating (controlling) between such effects and directing them. Given data from DNA microarray experiments and environmental records, we extract nonlinear ordinary differential equations that contain parameters that have to be determined. For this, we employ modern (Chebychevian) approximation and (generalized semi-infinite) optimization. After this is provided, time- discretized dynamical systems are studied. A combinatorial algorithm with polyhedra sequences allows to detect the region of parametric stability. Finally, we analyze the topological landscape of gene–environment networks with its structural (in)stability. By embedding as a module and investigating CO₂ emission control and figuring out game theoretical aspects, we conclude. This pioneering work is theoretically elaborated, practically devoted to health care, medicine, education, living conditions, and environmental protection, and it invites the readers to future research.      

微波消解-原子吸收光度法测定土壤中铜锌铅镉镍铬

用微波消解－原子吸收光度法测定土壤中铜，锌，铅，镉，镍和铬。通过硝酸－氢氟酸－过氧化氢体系消解液对土壤样品消解，选择出微波最佳消解条件。对硝酸－盐酸－过氧化氢体系消解液和硝酸－氢氟酸－过氧化氢体系消解液进行消解对比试验，发现前者不能将土壤样品完全消解，后者能将样品消解完全，但需将消解液中剩余的酸赶尽，否则测定结果将明显偏低。微波消解土壤与传统电热消解相比，操作简便快速，可提高工作效率。     

Topsoil and Housedust Metal Concentrations in the Vicinity of a Lead Battery Manufacturing Plant

The aim of the study was to determine the extent of heavy metal pollution in the vicinity of a lead battery manufacturing plant in the Czech Republic, both in the general environment and within homes. Topsoils (0–5 cm) were sampled from 100 sites along 4 transects which crossed the battery factory, the town centre and outlying rural areas. Housedust samples were collected from 15 plant-workers' homes and 15 non plant-workers' homes located at various distances from the factory. Samples were analysed for levels of Pb, Zn, Cd, Cu, As and Sb, using ICP-AES. Soil concentrations of Pb, Cd, As and Sb peaked at the perimeter fence of the battery factory with Pb levels of up to 12 650 g g> ^-1. Concentrations of these metals decreased exponentially within 500 m of the plant. Whilst the battery factory does appear to be a source of all the metals with the exception of Zn, emissions do not appear to be transported to any great extent over distances of more than 0.5 km. Topsoil and housedust concentrations of Pb, Zn, Cd, Cu, As and Sb in the general Mlada Boleslav area do not appear to be significantly different from those recorded in a large scale survey of urban soils in the United Kingdom. A comparison of housedust Pb concentrations in homes of plant workers and non-plant workers suggests that there may be a small input of Pb into the home environment by battery plant employees.     

An Overview of Contaminant-Related Issues Identified by Monitoring in San Francisco Bay

The San Francisco Estuary Regional Monitoring Program for Trace Substances (RMP) began in 1993 and is sponsored by 74 local, state, and federal agencies and companies through their discharge or Bay use permits. The RMP monitors water, sediment, toxicity, and bivalve bioaccumulation at 25 sites in the Bay that are considered to represent "background" conditions. Several major environmental issues have been identified by the RMP. Polychlorinated biphenyls and mercury were often above water quality guidelines, and often occurred in fish tissues above U.S. Environmental Protection Agency (U.S. EPA) screening values. Concentrations do not appear to be decreasing, suggesting continuing inputs. Episodes of aquatic toxicity often occurred following runoff events that transport contaminants into the Bay from urbanized and agricultural portions of the watershed. Sediment toxicity occurred throughout the Bay, and has been correlated with concentrations of specific contaminants (chlordanes, polynuclear aromatic hydrocarbons) at some locations; mixtures of contaminants were probably also important. Since the RMP does not monitor all ecosystem components, assessments of the overall condition of the Bay cannot be made. However, in terms of contamination, the RMP samples suggest that the South Bay, and North Bay sites are moderately contaminated.     

Biomagnification factors (fish to Osprey eggs from Willamette River,Oregon, U.S.A.) for PCDDs,PCDFs, PCBs and OC pesticides

A migratory population of 78 pairs of Osprey (Pandion haliaetus) nesting along the Willamette River in westernOregon was studied in 1993. The study was designed to determinecontaminant concentrations in eggs, contaminant concentrationsin fish species predominant in the Ospreys diet, andBiomagnification Factors (BMFs) of contaminants from fish specieseaten to Osprey eggs. Ten Osprey eggs and 25 composite samplesof fish (3 species) were used to evaluate organochlorine (OC)pesticides, polychlorinated biphenyls (PCBs), polychlorinateddibenzo-p-dioxins (PCDDs), and polychlorinated dibenzofurans(PCDFs). Mercury was also analyzed in fish. Geometric meanresidues in Osprey eggs were judged low, e.g., DDE 2.3 g g^-1 wet weight (ww), PCBs 0.69 g g^-1, 2,3,7,8-TCDD 2.3 ng kg^-1, and generally well below known threshold values for adverse effects on productivity, and the population was increasing. Osprey egg residue data presentedby River Mile (RM) are discussed, e.g., higher PCDDs were generally found immediately downstream of paper mills and eggsfrom the Willamette River had significantly elevated PCBs and PCDDs compared to reference eggs collected nearby in the CascadeMountains. Prey remains at nest sites indicated that the Largescale Sucker (Catostomus macrocheilus) and NorthernPikeminnow (Ptychocheilus oregonensis) accounted for an estimated 90.1% of the biomass in the Osprey diet, and composite samples of these two species were collected from different sampling sites throughout the study area for contaminant analyses. With the large percentage of the fishbiomass in the Osprey diet sampled for contaminants (and fisheaten by Ospreys similar in size to those chemically analyzed),and fish contaminant concentrations weighted by biomass intake, a mean BMF was estimated from fish to Osprey eggs for the largeseries of contaminants. BMFs ranged from no biomagnification(0.42) for 2,3,7,8-TCDF to 174 for OCDD. Our findings for themigratory Osprey were compared to BMFs for the resident HerringGull (Larus argentatus), and differences are discussed. Webelieve a BMF approach provides some basic understanding ofrelationships between contaminant burdens in prey species offish-eating birds and contaminants incorporated into their eggs,and may prove useful in understanding sources of contaminants inmigratory species although additional studies are needed.     

An investigation on biological stability of product water generated by lab-scale and pilot-scale distillation systems

Material Disposal Area G is the primary low-levelradioactive waste disposal site at Los Alamos NationalLaboratory, New Mexico, and is adjacent to Pueblo of SanIldefonso lands. Pueblo residents and Los Alamos scientists areconcerned about radiological doses resulting from uptake of AreaG radionuclides by mule deer (Odocoileus hemionus) andRocky Mountain elk (Cervus elaphus), then consumption ofdeer and elk meat by humans. Tissue samples were collected fromdeer and elk accidentally killed near Area G and were analyzedfor ³H, ⁹⁰Sr, total U, ²³⁸Pu, ^{239, 240}Pu,²⁴¹Am, and ¹³⁷Cs. These data were used to estimatehuman doses based on meat consumption of 23 kg y^-1. Humandoses were also modeled using RESRAD, and dose rates to deer andelk were estimated with a screening model. Dose estimates tohumans from tissue consumption were 2.9 × 10^-3 mSv y^-1and 1.6 × 10^-3 mSv y^-1 from deer and elk, respectively,and RESRAD dose estimates were of the same order of magnitude. Estimated dose rates to deer and elk were 2.1 × 10^-4 mGyd^-1 and 4.7 × 10^-4 mGy d^-1, respectively. Allestimated doses were significantly less than established exposurelimits or guidelines.     

The Draft of the New German Guideline VDI 3782/8 to Model Automobile Exhaust Dispersion

The draft of the German guideline to calculate automobile exhaust dispersion is explained. It contains a two-stage-system: For first quick estimates the guideline contains the simple models MLuS and STREET. In case these models are not applicable or their results shows concentration levels close to the air quality standards, the more complex models PROKAS_V and MISKAM are recommended. PROKAS_V is a Gaussian plume model, MISKAM is a 3-dimensional microscale non hydrostatic flow model for built-up areas with an Eulerian dispersion model. The guideline comprises cases in rural areas without or with few adjacent buildings as well as urban areas with buildings near the roads. The contribution gives information about the models, typical results and some of the problems showing up presently.     

Hydrocarbon Utilization in Yeast Isolates Found to Grow in Association with Petroleum in a Polluted Ultisol of Midwestern Nigeria

The population counts of hydrocarbon-utilising yeasts weremonitored at six sampling stations in the Benin City municipalarea over a four-week period. Although the population countswere relatively constant in each locality, the highest countsoccurred in areas heavily polluted by domestic and industrialeffluents. A total of thirty-five hydrocarbon-degrading yeastswere isolated from soil at the sampling stations usingn-hexadecane as sole carbon source. The isolates were identifiedas belonging to the genera Candida (27 strains), Endomycopsis (4 strains). All the organisms grew on long-chainn-alkane, kerosene, diesel oil and crude oil but failed to growon short-chain n-alkane, aromatic and alicyclic hydrocarbons.Measurement of growth attributes of the isolates usingn-hexadecane, diesel oil and crude oil as substrates showed thatthe Candida species were better utilizers of hydrocarbonsubstrates relative to Endomycopsis and Schizosaccharomyces species.     

Hydrologic–Economic Model for Managing Irrigation Intensity in Irrigation Areas under Watertable and Soil Salinity Targets

This paper gives mathematical details and sample applications of SWAGMAN Farm (SWAGMAN, Salt Water and Groundwater Management), a farm-scale hydrologic economic model that integrates agronomic, climatic, irrigation, hydrogeological and economic aspects of irrigated agriculture. The model is capable of determining optimum mix of land use to keep watertable and soil salinity within acceptable limits while maximising the economic returns. Alternatively, the model can simulate water and salt balance and economics of a given cropping preference. Web-based and Geographic Information Systems versions of the model are available for integration with the environmental reporting systems of the irrigation areas.     

Assessing health consequences in an environmental impact assessment: The case of Amsterdam Airport Schiphol

In this article a comprehensive approach for the evaluation of possible health effects in an environmental impact assessment (EIA) is described, illustrated with the example of Amsterdam Airport Schiphol. Unlike many EIAs, we estimated quantitatively the impact of aircraft-related pollution in terms of the number of affected people for aircraft noise annoyance, odour annoyance and hypertension. In addition, an analysis of health registry data on cardiovascular and respiratory diseases and a short survey on annoyance and risk perception were carried out. The scope of a health impact assessment depends on the situation, available knowledge and data, concern in the population about the impact and the number of people concerned. It is important to pay attention to the perception of risks and concerns from all parties involved. Moreover, the results demonstrate that far more people outside the area for which standards apply were affected than inside.