Field Performance of Point Velocity Probes at a Tidally Influenced Site

Conventional methods to estimate groundwater velocity that rely on Darcy's Law and average hydrogeologic parameter values are insensitive to local‐scale heterogeneities and anisotropy that control advective flow velocity and direction. Furthermore, at sites that are tidally influenced or have extraction wells with variable pumping schedules, infrequent water‐level measurements may not adequately characterize the range and significance of transient hydraulic conditions. The point velocity probe (PVP) is a recently developed instrument capable of directly measuring local‐scale groundwater flow velocity and direction. In particular, PVPs may offer distinct advantages for sites with complex groundwater–surface water interactions and/or with spatially and temporally variable groundwater flow conditions. The PVP utilizes a small volume of saline tracer and inexpensive sensors to directly measure groundwater flow direction and velocity in situ at the centimeter‐scale and discrete times. The probes are installed in conventional direct‐push borings, rather than in wells, thus minimizing the changes and biases in the local flow field caused by well installation and construction. Six PVPs were installed at a tidally influenced site in North Carolina to evaluate their implementability, performance, and potential value as a new site characterization tool. For this study, a new PVP prototype was developed using a rapid prototyping machine (i.e., a “three‐dimensional printer'') and included both horizontally and vertically oriented tracer detectors. A site‐specific testing protocol was developed to account for the spatially and temporally variable hydraulic conditions and groundwater salinity. The PVPs were tested multiple times, and the results were compared to the results of several different groundwater flux and velocity estimation tools and methods, including a heat‐pulse flowmeter, passive flux meters, single‐well tracer tests, and high‐resolution hydraulic gradient analysis. Overall, the results confirmed that the PVP concept is valid and demonstrated that reliable estimates of groundwater velocity and direction can be obtained in simple settings. Also, PVPs can be successfully installed by conventional methods at sites where the formation consists primarily of noncohesive soils and the water table is relatively shallow. Although some PVP tests yielded consistent and reliable results, several tests did not. This is likely due to the highly transient flow conditions and limitations associated with the PVP design and testing procedures. PVPs offer particular advantages over, and can effectively complement, other groundwater flow characterization techniques for certain conditions, and objectives may be useful for characterizing complex flow patterns under steady conditions; however, this study suggests that PVPs are best suited for conditions where the flow hydraulics are not highly transient. For sites where the hydraulic conditions are highly transient, the most reliable approach for understanding groundwater flow behavior and groundwater–surface water interactions would generally involve both a high‐resolution hydraulic gradient analysis and another local‐scale method, such as tracer testing. This study also highlighted some aspects of the current PVP design and testing protocol that can be improved upon, including a more robust connection between the PVP and injection line and further assessment of tracer solution density effects on vertical flow. © 2013 Wiley Periodicals, Inc.     

Recent developments in cleanup technologies

Traditional environmental investigations are expensive and time-consuming, involving heavy drilling equipment, several intermediate processes, and analyses at off-site commercial laboratories. New, relatively inexpensive in situ sampling surveys can now quickly generate preliminary data in the field, helping to analyze soil gas and soil and groundwater forvolatile organic compounds (VOCs). Many of the companies that do them now also provide their own mobile laboratories for delineating contaminant plumes more quickly and at less cost than the traditional methods and guiding the placement of groundwater monitoring wells and soil borings. This column describes the main in situ sampling surveys available today, calculates their costs per sample, explores their advantages and disadvantages for remedial investigations, and offers advice on how to carry them out.     

Field methods and example applications for the Min-Trap® mineral sampler

Important reactive minerals are commonly created during in situ groundwater remediation activities; for example, iron sulfides formed during enhanced reduction approaches can abiotically degrade many chlorinated solvents. However, cost-effective tools to evaluate these treatment processes in field applications are limited and the collection of samples to evaluate in situ mineral formation is costly due to drilling requirements. The new passive Min-Trap sampler is a simple and cost-effective tool that can directly measure the formation of reactive minerals in situ without the need for additional drilling or soil core collection. The methods presented here describe how Min-Traps deployed in conventional monitoring wells can measure reactive minerals and how these minerals can be identified through commercially available analytical methods. Several examples are presented that show how Min-Traps can be used to characterize the rate and spatial variability of reactive mineral precipitation and these data may support operation and optimization decisions.     

Matrix Diffusion Modeling Applied to Long‐Term Pump‐and‐Treat Data: 1. Method Development

Despite the installation in the 1980s and 1990s of hydraulic containment systems around known source zones (four slurry walls and ten pump‐and‐treat systems), trichloroethene (TCE) plumes persist in the three uppermost groundwater‐bearing units at the Middlefield‐Ellis‐Whisman (MEW) Superfund Study Area in Mountain View, California. In analyzing TCE data from 15 recovery wells, the observed TCE mass discharge decreased less than an order of magnitude over a 10‐year period despite the removal of an average of 11 pore volumes of affected groundwater. Two groundwater models were applied to long‐term groundwater pump‐and‐treat data from 15 recovery wells to determine if matrix diffusion could explain the long‐term persistence of a TCE plume. The first model assumed that TCE concentrations in the plume are controlled only by advection, dispersion, and retardation (ADR model). The second model used a one‐dimensional diffusion equation in contact with two low‐permeability zones (i.e., upper and lower aquitard) to estimate the potential effects of matrix diffusion of TCE into and out of low‐permeability media in the plume. In all 15 wells, the matrix diffusion model fit the data much better than the ADR model (normalized root mean square error of 0.17 vs. 0.29; r² of 0.99 vs. 0.19), indicating that matrix diffusion is a likely contributing factor to the persistence of the TCE plume in the non‐source‐capture zones of the MEW Study Area's groundwater‐extraction wells. © 2013 Wiley Periodicals, Inc.     

Innovative use of a pressure‐pulse injection tool to increase transmissivity in a collection trench

Pressure‐pulse injection tools are widely used in the oil and gas extraction industry to increase well production yields; however, they have been sparingly used in the environmental industry. These injection tools work by applying a pressure pulse to the subsurface that can open subsurface pore throats in unconsolidated material, increasing yields or increasing a radius of influence from a substrate injection. Collection trenches at an industrial site were installed to increase recovery of No. 2 fuel oil in the subsurface and maintain hydraulic control of the contaminant plume. However, after operating for seven years, significant reduction in recovery was observed. Diminished recovery was attributed to biofouling, iron fouling, and/or excessive scaling. A pilot test was conducted in 2009 to determine if a pressure‐pulse injection tool could be used to inject an antifouling agent and rehabilitate two of the site collection trenches. The pilot test was successful in increasing the transmissivity of both trenches, with an order‐of‐magnitude increase in groundwater recovery at Collection Trench 1 and a 50 percent increase in recovery at Collection Trench 2. The trench rehabilitation using the pressure‐pulse injection tool was conducted at two other site collection trenches in 2010 with similar success and is now proposed as part of regular maintenance of the trenches on an as‐needed basis. © 2011 Wiley Periodicals, Inc.     

Detecting and quantifying reductive dechlorination under monitored natural attenuation conditions

Field sampling and testing were used to investigate the relationship between baseline geochemical and microbial community data and in situ reductive dechlorination rates at a site contaminated with trichloroethene (TCE) and carbon tetrachloride (CTET). Ten monitoring wells were selected to represent conditions along groundwater flow paths from the contaminant source zone to a wetlands groundwater discharge zone. Groundwater samples were analyzed for a suite of geochemical and microbial parameters; then push‐pull tests with fluorinated reactive tracers were conducted in each well to measure in situ reductive dechlorination rates. No exogenous electron donors were added in these tests, as the goal was to assess in situ reductive dechlorination rates under natural attenuation conditions. Geochemical data provided preliminary evidence that reductive dechlorination of TCE and CTET was occurring at the site, and microbial data confirmed the presence of known dechlorinating organisms in groundwater. Push‐pull tests were conducted using trichlorofluoroethene (TCFE) as a reactive tracer for TCE and, in one well, trichlorofluoromethane (TCFM) as a reactive tracer for CTET. Injected TCFE was transformed to cis‐ and trans‐dichlorofluoroethene and chlorofluoroethene, and, in one test, injected TCFE was completely dechlorinated to fluoroethene (FE). In situ TCFE transformation rates ranged from less than 0.005 to 0.004/day. In the single well tested, injected TCFM was transformed in situ to dichlorofluoromethane and chlorofluoromethane; the TCFM transformation rate was estimated as 0.001/day. The results indicate that it is possible to use push‐pull tests with reactive tracers to directly detect and quantify reductive dechlorination of chlorinated ethenes and ethanes under monitored natural attenuation conditions, which has not previously been demonstrated. Transformation rate estimates obtained with these techniques should improve the accuracy of contaminant transport modeling. © 2012 Wiley Periodicals, Inc.     

Remediating Contaminated Groundwater With Low‐Capacity Injection and Nonpumped Wells

This modeling study evaluated the capability of low‐capacity wells injecting clean water and nonpumped wells equipped with filter media for containing and removing a contaminant plume in groundwater. Outcomes were compared for configurations of: (1) nonpumped wells, (2) nonpumped wells and injection wells (injecting less than 1 m³/d), and (3) no wells (baseline scenario). Results suggest that hybrid configurations featuring both types of wells can be an effective, low‐cost strategy for containing and remediating contaminated groundwater. Strategically positioned injection wells funnel contaminant plumes toward nonpumped wells, thus requiring fewer nonpumped wells to contain and remove a contaminant plume. © 2013 Wiley Periodicals, Inc.     

Field‐scale evaluation of a biobarrier for the treatment of a trichloroethene plume

In the 1960s, trichloroethene (TCE) was used at what is now designated as Installation Restoration Program Site 32 Cluster at Vandenberg Air Force Base to flush missile engines prior to launch and perhaps for other degreasing activities, resulting in releases of TCE to groundwater. The TCE plume extends approximately 1 kilometer from the previous launch facilities beyond the southwestern end of the site. To limit further migration of TCE and chlorinated degradation by‐products, an in situ, permeable, reactive bioremediation barrier (biobarrier) was designed as a cost‐effective treatment technology to address the TCE plume emanating from the source area. The biobarrier treatment would involve injecting carbon‐based substrate and microbes to achieve reductive dechlorination of volatile organic compounds, such as TCE. Under reducing conditions and in the presence of certain dechlorinating microorganisms, TCE degrades to nontoxic ethene in groundwater. To support the design of the full‐scale biobarrier, a pilot test was conducted to evaluate site conditions and collect pertinent design data. The pilot test results indicated possible substrate delivery difficulties and a smaller radius of influence than had been estimated, which would be used to determine the final biobarrier well spacing. Based on these results, the full‐scale biobarrier design was modified. In January 2010, the biobarrier was implemented at the toe of the source area by adding a fermentable substrate and a dechlorinating microbial culture to the subsurface via an injection well array that spanned the width of the TCE plume. After the injections, the groundwater pH in the injection wells continued to decrease to a level that could be detrimental to the population of Dehalococcoides in the SDC‐9^TM culture. In addition, 7 months postinjection, the injection wells could not be sampled due to fouling. Cleaning was required to restore their functions. Bioassay and polymerase chain reaction analyses were conducted, as well as titration tests, to assess the need for biobarrier amendments in response to the fouling issues and low pH. Additionally, slug tests were performed on three wells to evaluate possible localized differences in hydraulic conductivity within the biobarrier. Based on the test results, the biobarrier was amended with sodium carbonate and inoculated a second time with SDC‐9^TM. The aquifer pH was restored, and reductive dechlorination resumed in the treatment zone, evidenced by the reduction in TCE and the increase in degradation products, including ethene. © 2011 Wiley Periodicals, Inc.     

The horizontal reactive media treatment well (HRX Well®) for passive in situ remediation: Design,implementation, and sustainability considerations

A new in situ remediation concept termed a Horizontal Reactive Media Treatment Well (HRX Well^®) is presented that utilizes a horizontal well filled with reactive media to passively treat contaminated groundwater in situ. The approach involves the use of a large‐diameter directionally drilled horizontal well filled with solid reactive media installed parallel to the direction of groundwater flow. The engineered contrast in hydraulic conductivity between the high in‐well reactive media and the ambient aquifer hydraulic conductivity results in the passive capture, treatment, and discharge back to the aquifer of proportionally large volumes of groundwater. Capture and treatment widths of up to tens of feet can be achieved for many aquifer settings, and reductions in downgradient concentrations and contaminant mass flux are nearly immediate. Many different types of solid‐phase reactive treatment media are already available (zero valent iron, granular activated carbon, biodegradable particulate organic matter, slow‐release oxidants, ion exchange resins, zeolite, apatite, etc.). Therefore, this concept could be used to address a wide range of contaminants. Laboratory and pilot‐scale test results and numerical flow and transport model simulations are presented that validate the concept. The HRX Well can access contaminants not accessible by conventional vertical drilling and requires no aboveground treatment or footprint and requires limited ongoing maintenance. A focused feasibility evaluation and alternatives analysis highlights the potential cost and sustainability advantages of the HRX Well compared to groundwater extraction and treatment systems or funnel and gate permeable reactive barrier technologies for long‐term plume treatment. This paper also presents considerations for design and implementation for a planned upcoming field installation.     

Taproot™ technology: Tree coring for fast,noninvasive plume delineations

In efforts to evaluate the use of plants as a forensic tool for delineating contaminated soil and groundwater, a laboratory experiment and a field sampling effort were undertaken. Site assessments are often costly and inaccurate, requiring multiple mobilizations to hone in on source areas and getting accurate estimates of contaminant extent and distribution. As these extensive site delineations take place, valuable time and resources are lost. The findings of this study show that plants can be used as a tool to evaluate a variety of subsurface contaminants, either in the vadose zone or in the saturated zone. In the first field application of Taproot? Technology, a large, heavily forested site was sampled in one day and the contamination on‐site was more accurately delineated than had been generated at the site in over a decade, with more than 26 wells installed. New source zones were detected on the site, and the presence of new waste depositions was uncovered for the first time showing the great value of tree coring as a contaminant detection tool. © 2009 Wiley Periodicals, Inc.     

Interior versus exterior configurations of passive wells with filter cartridges for cleaning contaminated groundwater

This study considered alternative configurations of passive wells equipped with filter cartridges for removing contaminated groundwater. The wells fully penetrated a simulated unconfined aquifer. Both homogeneous and heterogeneous hydraulic conductivity distributions were considered. An initial configuration comprised wells along the downgradient perimeter of a contaminant plume, spaced 0.5 m in the direction transverse to regional groundwater flow. Additional wells near the downgradient tip of the plume prevented off‐site contamination. Alternative configurations had the same number of wells, but some included wells along higher (interior) concentration contours to facilitate quicker removal of the contaminant plume. Results suggest that downgradient configurations generally outperform alternatives, although repositioning a few outer wells near the contaminant source may be effective in some cases. © 2009 Wiley Periodicals, Inc.     

Developing Life‐Cycle Environmental Response Costs for Leaking Underground Storage Systems at Service Station Sites

Leaking underground storage tank systems at service stations have resulted in tens of thousands of petroleum releases and associated groundwater chemical plumes often extending hundreds of feet off‐site. Technical and engineering approaches to assess and clean up releases from underground tanks, product lines, and dispensers using technologies such as soil vapor extraction, air sparging, biostimulation, and monitored natural attenuation are well understood and widely published throughout the literature. This article summarizes life‐cycle environmental response costs typically encountered using site‐specific cost estimation or metric‐based cost categories considering the overall complexity of site conditions: (1) simple sites where response actions require smaller scale assessments and/or remediation and have limited or no off‐site impacts; (2) average sites where response actions require larger scale assessments and/or remediation typical of petroleum releases; (3) complex sites where response actions require greater on‐site and/or off‐site remediation efforts; and (4) mega sites where petroleum plumes have impacted public or private water supplies or where petroleum vapors have migrated into occupied buildings. Associated cleanup cost estimates rely upon appropriate combinations of individual work elements and the duration of operation, maintenance, and monitoring activities. These cost estimates can be offset by state reimbursement funds, coverage in purchase agreements, and insurance policies. A case study involving a large service station site portfolio illustrates the range of site complexity and life‐cycle environmental response costs. © 2014 Wiley Periodicals, Inc.     

The treatment of contaminated water at remedial wood preserving sites

Contaminated groundwater and surface water have posed a great challenge in restoring wood preserving sites to beneficial use. Often contaminated groundwater plumes extend far beyond the legal property limits, adversely impacting drinking water supplies and crop lands. To contain, treat, and/or remediate these valuable resources is an important part of restoring these impacted sites. Various options are available for remediating the groundwater and other affected media at these sites. Frequently, pump and treat technologies have been used that can provide well‐head treatment at installed extraction wells. This approach has shown to be costly and excessively time consuming. Some of the technologies used for pump and treat are granular activated carbon (GAC), biotreatment, and chemical oxidation. Other approaches use in‐situ treatment applications that include enhanced bioremediation, monitored natural attenuation (biotic and abiotic), and chemical reduction/fixation. Ultimately, it may only be feasible, economically or practicably, to use hydraulic containment systems. Depending upon site‐specific conditions, these treatment approaches can be used in various combinations to offer the best remedial action. A comparison of water treatment system costs extrapolated from the treatability studies performed on contaminated groundwater from the McCormick/Baxter Superfund site in Stockton, California, yielded operation and maintenance costs of $1.19/1,000 gal. for carbon treatment and $7.53/1,000 gal. for ultraviolet (UV) peroxidation, respectively.     

Isotope applications in environmental investigations part II: Groundwater age dating and recharge processes,and provenance of sulfur and methane

Measurement of the isotopic composition of solids, solutes, gases, and water complement standard hydrogeological investigation techniques by providing information that may not otherwise be obtainable. Groundwater age estimates determined from the decay of radio‐isotopes or from groundwater concentrations of anthropogenic gases such as chlorofluorocarbons (CFCs) and sulfur hexafluoride (SF₆) are used to verify flow regimes and constrain or calibrate hydrologic flow models. Groundwater recharge rates are estimated by measuring the concentrations or activities of a variety of isotopes including ²H, ³H, ¹⁸O, and ³⁶Cl. Excess sulfur causes salinization of water supplies and acidification of precipitation, surface water, and groundwater. The wide range of sulfur isotopic compositions exhibited by different sulfur species and sources allows the application of sulfur isotopes to trace sources and fate of sulfur in the environment. Methane is a ubiquitous gas that has economic value when located in extractable reservoirs. Methane is also a greenhouse gas and is a potential explosion and health hazard when it accumulates in buildings and water distribution systems. The carbon and hydrogen isotopic composition of methane can be used to determine the provenance of methane, distinguishing between thermogenic and biogenic sources. The addition of isotopic analyses to environmental investigations can be a cost‐effective means of resolving intractable issues. © 2003 Wiley Periodicals, Inc.     

Evolution of predictive tools for in situ bioremediation and natural attenuation evaluations

Proving the viability of in situ bioremediation technologies and gathering data for its full‐scale implementation typically involves collecting multiple rounds of data and often completing microcosm studies. Collecting these data is cumbersome, time‐consuming, costly, and typically difficult to scale. A new method of completing microcosm studies in situ using an amendable sampling device deployed and incubated in groundwater monitoring wells provides actionable data to expedite site cleanup. The device, referred to as a Bio‐Trap® sampler, is designed to collect actively colonizing microbes and dissolved organic compounds from groundwater for analysis using conventional analytical techniques and advanced diagnostic tools that can answer very specific design and viability questions relating to bioremediation. Key data that can be provided by in situ microcosm studies using Bio‐Trap® samplers include definitively demonstrating contaminant destruction by using compound‐specific isotope analysis and providing data on the mechanism of the degradation by identifying the responsible microbes. Three case studies are presented that demonstrate the combined flexibility of Bio‐Trap® samplers and advanced site diagnostics. The applications include demonstrating natural attenuation of dissolved chlorinated solvents, demonstrating natural attenuation of dissolved petroleum compounds, and using multiple Bio‐Trap® samplers to comparatively assess the viability of bioaugmentation at a chlorinated solvent release site. At each of these sites, the in situ microcosm studies quickly and cost‐effectively answered key design and viability questions, allowing for regulatory approval and successful full‐scale implementation. © 2010 Wiley Periodicals, Inc.     

The hyporheic zone: Linking groundwater and surface water—understanding the paradigm

The hyporheic zone, the transition region between groundwater and surface water, represents an important interface between terrestrial and aquatic ecosystems. When groundwater combines with surface water in this zone, the characteristics of each are blended and new gradients are established, especially for contaminants. Therefore, the hyporheic zone is important in considering the “big ecological picture” as the hydrologic continuum connecting groundwater and surface water. The importance is reflected by the current focus of this zone in ecological risk assessments conducted under the Resource Conservation and Recovery Act (RCRA), Comprehensive Environmental Response, Compensation and Liability Act (CERCLA), and Clean Water Act (CWA) programs. A variety of tools can be used to measure, analyze, and predict the physical, chemical, and biological processes that occur within the hyporheic zone. Directly measuring the flux of water across the interface between groundwater and surface water determines whether surface water enters the streambed at downwelling zones or groundwater discharges from the streambed in upwelling zones. In addition to direct measurements of the flux of water, several states have developed models to characterize the interaction of groundwater and surface water. The variability in physical and chemical characteristics between upwelling and downwelling zones influences the local ecology within the zone. The study of the species within the hyporheic zone includes ecological surveys and ecotoxicological investigations. The evolving study of the hyporheic zone will necessitate an increase in basic research into hydraulic considerations, an identification of regional representative sites with contaminated hyporheic zones, and a better understanding of the ecology of the species within the zone. © 2001 John Wiley & Sons, Inc.     

石油开采行业土壤污染防治对策与建议

在文献和实地调研的基础上,分析了石油开采行业生产工艺及产排污情况,识别了油井、注水井、输油管道、联合站等主要工艺节点的土壤污染风险,总结了目前行业处理废水和危险废物的主要方法,指出了行业在废弃钻井液处理、地下输油管道泄漏后期处置及突发环境事件应急预案中土壤污染防治等方面存在的问题,并提出了相应的对策和建议。     

Laboratory validation study of new vapor‐phase‐based approach for groundwater monitoring

Recent improvements in field‐portable analytical equipment allow accurate on‐site measurement of VOCs present in air at concentrations of less than 0.1 parts per million volume (ppmv). The objective of this project is to determine if the use of these instruments for vapor‐phase measurements of headspace in a monitoring well can serve as a reliable and accurate method for monitoring volatile organic compound (VOC) concentrations in groundwater under equilibrium conditions. As part of a comprehensive research project investigating the utility of this proposed monitoring method, the authors have completed a laboratory validation study to identify instruments and sample‐collection methods that will provide accurate measurement of VOC concentrations in groundwater. This laboratory validation study identified two field‐portable instruments (a gas chromatograph and a photoionization detector) with sufficient sensitivity to measure VOCs in groundwater at concentrations below typical monitoring standards (i.e., 1 to 5 μg/L). The accuracy and precision of these field instruments was sufficient to satisfy typical data‐quality objectives for laboratory‐based analysis. In addition, two sample‐collection methods were identified that yield vapor‐phase samples in equilibrium with water: direct headspace sampling and passive diffusion samplers. These sample‐collection methods allow the field instruments (which measure VOC concentrations in vapor‐phase samples) to be used to measure VOC concentrations in water. After further validation of these sample‐collection methods in the field, this monitoring method will provide a simple way to obtain accurate real‐time measurements of VOC concentrations in groundwater using inexpensive field‐portable analytical instruments. © 2009 Wiley Periodicals, Inc.     

In‐Situ and Ex‐Situ Bioremediation Options for Treating Perchlorate in Groundwater

Perchlorate has been identified as a water contaminant in 14 states, including California, Nevada, New Mexico, Arizona, Utah, and Texas, and current estimates suggest that the compound may affect the drinking water of as many as 15 million people. Biological treatment represents the most‐favorable technology for the effective and economical removal of perchlorate from water. Biological fluidized bed reactors (FBRs) have been tested successfully at the pilot scale for perchlorate treatment at several sites, and two full‐scale FBR systems are currently treating perchlorate‐contaminated groundwater in California and Texas. A third full‐scale treatment system is scheduled for start‐up in early 2002. The in‐situ treatment of perchlorate through addition of specific electron donors to groundwater also appears to hold promise as a bioremediation technology. Recent studies suggest that perchlorate‐reducing bacteria are widely occurring in nature, including in groundwater aquifers, and that these organisms can be stimulated to degrade perchlorate to below the current analytical reporting limit (< 4 μg/l) in many instances. In this article, in‐situ and ex‐situ options for biological treatment of perchlorate‐contaminated groundwater are discussed and results from laboratory and field experiments are presented. © 2002 Wiley Periodicals, Inc.     

Best Available Treatment Technologies Applied to Groundwater Circulation Wells

Groundwater circulation wells (GCWs) are a quasi‐in‐situ method for remediating groundwater in areas where remediation techniques that limit the water available for municipal, domestic, industrial, or agricultural purposes are inappropriate. The inherently resource‐conservative nature of groundwater circulation wells is also philosophically appealing in today's culture, which is supportive of green technologies. Groundwater circulation wells involve the circulation of groundwater through a dual‐screen well, with treatment occurring between the screens. The wells are specifically designed so that one well screen draws in groundwater and the second returns the groundwater after it has been treated within the well. Historically, the treatment has been performed with specialized equipment proprietary to GCW vendors. Two full‐scale pilot systems at a formerly used Defense Superfund site in Nebraska used best available technologies for treatment components. A multiple‐tray, low‐profile air stripper typically used for pump‐and‐treat remediation systems was successfully adapted for the GCW pilot system located in a trichloroethylene (TCE) hot spot. An ultraviolet water disinfection system was successfully adapted for the GCW pilot system located in a hot spot contaminated with the explosive compound hexhydro‐1,3,5‐trinitro‐1,3,5‐triazine (RDX). The pilot systems showed that GCW technology is competitive with a previously considered pump‐and‐treat alternative for focused extraction, and the regulatory community was supportive of additional GCW applications. A remedial design for the site includes 12 more GCW systems to complete focused remediation requirements. © 2002 Wiley Periodicals, Inc.