Concurrent nitrate and Fe(III) reduction during anaerobic biodegradation of phenols in a sandstone aquifer

The biodegradation of phenols (5, 60, 600 mg l⁻¹) under anaerobic conditions (nitrate enriched and unamended) was studied in laboratory microcosms with sandstone material and groundwater from within an anaerobic ammonium plume in an aquifer. The aqueous phase was sampled and analyzed for phenols and selected redox sensitive parameters on a regular basis. An experiment with sandstone material from specific depth intervals from a vertical profile across the ammonium plume was also conducted. The miniature microcosms used in this experiment were sacrificed for sampling for phenols and selected redox sensitive parameters at the end of the experiment. The sandstone material was characterized with respect to oxidation and reduction potential and Fe(II) and Fe(III) speciation prior to use for all microcosms and at the end of the experiments for selected microcosms.The redox conditions in the anaerobic microcosms were mixed nitrate and Fe(III) reducing. Nitrate and Fe(III) were apparently the dominant electron acceptors at high and low nitrate concentrations, respectively. When biomass growth is taken into account, nitrate and Fe(III) reduction constituted sufficient electron acceptor capacity for the mineralization of the phenols observed to be degraded even at an initial phenols concentration of 60 mg l⁻¹ (high) in an unamended microcosm, whereas nitrate reduction alone is unlikely to have provided sufficient electron acceptor capacity for the observed degradation of the phenols in the unamended microcosm.For microcosm systems, with solid aquifer materials, dissolution of organic substances from the solid material may occur. A quantitative determination of the speciation (mineral types and quantity) of electron acceptors associated with the solids, at levels relevant for degradation of specific organic compounds in aquifers, cannot always be obtained. Hence, complete mass balances of electron acceptor consumption for specific organic compounds degradation are difficult to confine. For aquifer materials with low initial Fe(II) content, Fe(II) determinations on solids and in aqueous phase samples may provide valuable information on Fe(III) reduction. However, in microcosms with natural sediments and where electron acceptors are associated with the sediments, complete mass-balances for substrates and electron acceptors are not likely to be obtained.     

Denitrification and phenol degradation in a contaminated aquifer

A natural groundwater system modified by pollutant phenols and agricultural nitrate has been modelled in the laboratory by a series of sacrificial microcosm experiments. Samples of aquifer sediment and groundwater from the margin of the phenol plume were used to inoculate anaerobic microcosms enriched in nitrate and pollutant phenols. Rapid degradation of phenol and p-cresol was observed over a 35-day period leading to the generation of inorganic carbon and a number of transient intermediates. O-cresol proved to be recalcitrant on the experimental time-scale. A mass balance calculation shows that, during degradation, carbon was conserved in the aqueous phase. Groundwater-sediment interactions were monitored using carbon stable isotope data. A mass balance for solution TIC indicates thatp-cresol degradation stimulated the dissolution of sedimentary carbonate phases due to the formation of carbonic acid. Compound-specific carbon isotope analysis (GC-IRMS) was used to search for 13C enrichment in residual p-cresol. A slight enrichment trend (epsilon = -2.5/1000) was tentatively identified. The potential of this fractionation effect for obtaining in situ degradation rates is discussed. Results from the microcosm experiments help to explain the observed distribution of nitrate and phenols within the polluted aquifer.     

Mixing-controlled biodegradation in a toluene plume--results from two-dimensional laboratory experiments

Various abiotic and biotic processes such as sorption, dilution, and degradation are known to affect the fate of organic contaminants, such as petroleum hydrocarbons in saturated porous media. Reactive transport modeling of such plumes indicates that the biodegradation of organic pollutants is, in many cases, controlled by mixing and therefore occurs locally at the plume's fringes, where electron donors and electron-acceptors mix. Herein, we aim to test whether this hypothesis can be verified by experimental results obtained from aerobic and anaerobic degradation experiments in two-dimensional sediment microcosms. Toluene was selected as a model compound for oxidizable contaminants. The two-dimensional microcosm was filled with quartz sand and operated under controlled flow conditions simulating a contaminant plume in otherwise uncontaminated groundwater. Aerobic degradation of toluene by Pseudomonas putida mt-2 reduced a continuous 8.7 mg L(-1) toluene concentration by 35% over a transport distance of 78 cm in 15.5 h. In comparison, under similar conditions Aromatoleum aromaticum strain EbN1 degraded 98% of the toluene infiltrated using nitrate (68.5+/-6.2 mg L(-1)) as electron acceptor. A major part of the biodegradation activity was located at the plume fringes and the slope of the electron-acceptor gradient was steeper during periods of active biodegradation. The distribution of toluene and the significant overlap of nitrate at the plume's fringe indicate that biokinetic and/or microscale transport processes may constitute additional limiting factors. Experimental data is corroborated with results from a reactive transport model using double Monod kinetics. The outcome of the study shows that in order to simulate degradation in contaminant plumes, detailed data sets are required to test the applicability of models. These will have to deal with the incorporation of existing parameters coding for substrate conversion kinetics and microbial growth.     

Processes controlling the distribution and natural attenuation of dissolved phenolic compounds in a deep sandstone aquifer

Processes controlling the distribution and natural attenuation (NA) of phenol, cresols and xylenols released from a former coal-tar distillation plant in a deep Triassic sandstone aquifer are evaluated from vertical profiles along the plume centerline at 130 and 350 m from the site. Up to four groups of contaminants (phenols, mineral acids, NaOH, NaCl) form discrete and overlapping plumes in the aquifer. Their distribution reflects changing source history with releases of contaminants from different locations. Organic contaminant distribution in the aquifer is determined more by site source history than degradation. Contaminant degradation at total organic carbon (TOC) concentrations up to 6500 mg l(-1) (7500 mg l(-1) total phenolics) is occurring by aerobic respiration NO3-reduction, Mn(IV)-/Fe(III)-reduction, SO4-reduction, methanogenesis and fermentation, with the accumulation of inorganic carbon, organic metabolites (4-hydroxybenzaldehyde, 4-hydroxybenzoic acid), acetate, Mn(II), Fe(II), S(-II), CH4 and H2 in the plume. Aerobic and NO3-reducing processes are restricted to a 2-m-thick plume fringe but Mn(IV)-/Fe(II)-reduction, SO4-reduction, methanogenesis and fermentation occur concomitantly in the plume. Dissolved H2 concentrations in the plume vary from 0.7 to 110 nM and acetate concentrations reach 200 mg l(-1). The occurrence of a mixed redox system and concomitant terminal electron accepting processes (TEAPs) could be explained with a partial equilibrium model based on the potential in situ free energy (deltaGr) yield for oxidation of H2 by specific TEAPs. Respiratory processes rather than fermentation are rate limiting in determining the distribution of H2 and TEAPs and H2 dynamics in this system. Most (min. 90%) contaminant degradation has occurred by aerobic and NO3-reducing processes at the plume fringe. This potential is determined by the supply of aqueous O2 and NO3 from uncontaminated groundwater, as controlled by transverse mixing, which is limited in this aquifer by low dispersion. Consumption to date of mineral oxides and SO4 is, respectively, <0.15% and 0.4% of the available aquifer capacity, and degradation using these oxidants is <10%. Fermentation is a significant process in contaminant turnover, accounting for 21% of degradation products present in the plume, and indicating that microbial respiration rates are slow in comparison with fermentation. Under present conditions, the potential for degradation in the plume is very low due to inhibitory effects of the contaminant matrix. Degradation products correspond to <22% mass loss over the life of the plume, providing a first-order plume scale half-life >140 years. The phenolic compounds are biodegradable under the range of redox conditions in the aquifer and the aquifer is not oxidant limited, but the plume is likely to be long-lived and to expand. Degradation is likely to increase only after contaminant concentrations are reduced and aqueous oxidant inputs are increased by dispersion of the plume. The results imply that transport processes may exert a greater control on the natural attenuation of this plume than aquifer oxidant availability.     

Enantioselective biodegradation of mecoprop in aerobic and anaerobic microcosms

Natural attenuation of mecoprop has been studied by determining changes in enantiomeric fraction in different redox environments down gradient from a landfill in the Lincolnshire limestone. Such changes could be due to differential metabolism of the enantiomers, or enantiomeric inversion. In order to confirm the processes occurring in the field, microcosm experiments were undertaken using limestone acclimatised in different redox zones. No biodegradation was observed in the methanogenic, sulphate-reducing or iron-reducing microcosms. In the nitrate-reducing microcosm (S)-mecoprop did not degrade but (R)-mecoprop degraded with zero order kinetics at 0.65 mg l(-1)day(-1) to produce a stoichiometric equivalent amount of 4-chloro-2-methylphenol. This metabolite only degraded when the (R)-mecoprop disappeared. In aerobic conditions (S)- and (R)-mecoprop degraded with zero order kinetics at rates of 1.90 and 1.32 mg l(-1)day(-1) respectively. The addition of nitrate to dormant iron-reducing microcosms devoid of nitrate stimulated anaerobic degradation of (R)-mecoprop after a lag period of about 20 days and was associated with the production of 4-chloro-2-methylphenol. Nitrate addition to sulphate-reducing/methanogenic microcosms did not stimulate mecoprop degradation. However, the added nitrate was completely utilised in oxidising sulphide to sulphate. There was no evidence for enantiomeric inversion. The study reveals new evidence for fast enantioselective degradation of (R)-mecoprop under nitrate-reducing conditions.     

Changes in enantiomeric fraction as evidence of natural attenuation of mecoprop in a limestone aquifer

Natural attenuation of the chiral pesticide mecoprop [2-(2-methyl-4-chlorophenoxy)propionic acid] has been studied by determining changes in its enantiomeric fraction in different redox environments down gradient of a landfill in the Lincolnshire Limestone. Previous studies have shown that mecoprop degrades predominantly aerobically and that differences in the biological behaviour of the two enantiomers will change their relative proportions during biodegradation. Originally deposited as a racemic mixture, there has been no change in the enantiomeric fraction in the most polluted part of the landfill plume where conditions are sulphate reducing/methanogenic. In the nitrate-reducing zone, the proportion of (S)-mecoprop increases, suggesting preferential degradation of (R)-mecoprop; while in the aerobic zone, the proportion of (R)-mecoprop increases, suggesting faster degradation of (S)-mecoprop. Mecoprop persistence in the confined Lincolnshire Limestone further downdip is explained by inhibition of degradation in sulphate-reducing conditions, which develop naturally. Laboratory microcosm experiments using up to 10 mg l(-1) of mecoprop confirm these inferences and show that under aerobic conditions, (S)-mecoprop and (R)-mecoprop degrade with zero-order kinetics at rates of 1.90 and 1.32 mg l(-1) day(-1), respectively. Under nitrate-reducing conditions (S)-mecoprop does not degrade, but (R)-mecoprop degrades with zero-order kinetics at 0.65 mg l(-1) day(-1) to produce a stoichiometric equivalent amount of 4-chloro-2-methylphenol. This metabolite only degrades when the (R)-mecoprop has disappeared. The addition of nitrate to a dormant iron-reducing microcosm devoid of nitrate stimulated anaerobic degradation of (R)-mecoprop after a lag period of 21 days. There was no evidence for enantiomeric inversion. The study demonstrates the sensitivity of changes in enantiomeric fraction for detecting natural attenuation, and reveals subtle differences in mecoprop degradation in different redox environments within the Lincolnshire Limestone aquifer.     

Biodegradation potential of MTBE in a fractured chalk aquifer under aerobic conditions in long-term uncontaminated and contaminated aquifer microcosms

The potential for aerobic biodegradation of MTBE in a fractured chalk aquifer is assessed in microcosm experiments over 450 days, under in situ conditions for a groundwater temperature of 10 °C, MTBE concentration between 0.1 and 1.0 mg/L and dissolved O₂ concentration between 2 and 10 mg/L. Following a lag period of up to 120 days, MTBE was biodegraded in uncontaminated aquifer microcosms at concentrations up to 1.2 mg/L, demonstrating that the aquifer has an intrinsic potential to biodegrade MTBE aerobically. The MTBE biodegradation rate increased three-fold from a mean of 6.6 ± 1.6 μg/L/day in uncontaminated aquifer microcosms for subsequent additions of MTBE, suggesting an increasing biodegradation capability, due to microbial cell growth and increased biomass after repeated exposure to MTBE. In contaminated aquifer microcosms which also contained TAME, MTBE biodegradation occurred after a shorter lag of 15 or 33 days and MTBE biodegradation rates were higher (max. 27.5 μg/L/day), probably resulting from an acclimated microbial population due to previous exposure to MTBE in situ. The initial MTBE concentration did not affect the lag period but the biodegradation rate increased with the initial MTBE concentration, indicating that there was no inhibition of MTBE biodegradation related to MTBE concentration up to 1.2 mg/L. No minimum substrate concentration for MTBE biodegradation was observed, indicating that in the presence of dissolved O₂ (and absence of inhibitory factors) MTBE biodegradation would occur in the aquifer at MTBE concentrations (ca. 0.1 mg/L) found at the front of the ether oxygenate plume. MTBE biodegradation occurred with concomitant O₂ consumption but no other electron acceptor utilisation, indicating biodegradation by aerobic processes only. However, O₂ consumption was less than the stoichiometric requirement for complete MTBE mineralization, suggesting that only partial biodegradation of MTBE to intermediate organic metabolites occurred. The availability of dissolved O₂ did not affect MTBE biodegradation significantly, with similar MTBE biodegradation behaviour and rates down to ca. 0.7 mg/L dissolved O₂ concentration. The results indicate that aerobic MTBE biodegradation could be significant in the plume fringe, during mixing of the contaminant plume and uncontaminated groundwater and that, relative to the plume migration, aerobic biodegradation is important for MTBE attenuation. Moreover, should the groundwater dissolved O₂ concentration fall to zero such that MTBE biodegradation was inhibited, an engineered approach to enhance in situ bioremediation could supply O₂ at relatively low levels (e.g. 2–3 mg/L) to effectively stimulate MTBE biodegradation, which has significant practical advantages. The study shows that aerobic MTBE biodegradation can occur at environmentally significant rates in this aquifer, and that long-term microcosm experiments (100s days) may be necessary to correctly interpret contaminant biodegradation potential in aquifers to support site management decisions.     

Degradation of 1,1,2,2-tetrachloroethane and accumulation of vinyl chloride in wetland sediment microcosms and in situ porewater: biogeochemical controls and associations with microbial communities

The biodegradation pathways of 1,1,2,2-tetrachloroethane (TeCA) and 1,1,2-trichloroethane (112TCA) and the associated microbial communities in anaerobic wetland sediments were evaluated using concurrent geochemical and genetic analyses over time in laboratory microcosm experiments. Experimental results were compared to in situ porewater data in the wetland to better understand the factors controlling daughter product distributions in a chlorinated solvent plume discharging to a freshwater tidal wetland at Aberdeen Proving Ground, Maryland. Microcosms constructed with wetland sediment from two sites showed little difference in the initial degradation steps of TeCA, which included simultaneous hydrogenolysis to 112TCA and dichloroelimination to 1,2-dichloroethene (12DCE). The microcosms from the two sites showed a substantial difference, however, in the relative dominance of subsequent dichloroelimination of 112TCA. A greater dominance of 112TCA dichloroelimination in microcosms constructed with sediment that was initially iron-reducing and subsequently simultaneously iron-reducing and methanogenic caused approximately twice as much vinyl chloride (VC) production as microcosms constructed with sediment that was methanogenic only throughout the incubation. The microcosms with higher VC production also showed substantially more rapid VC degradation. Field measurements of redox-sensitive constituents, TeCA, and its anaerobic degradation products along flowpaths in the wetland porewater also showed greater production and degradation of VC with concurrent methanogenesis and iron reduction. Molecular fingerprinting indicated that bacterial species [represented by a peak at a fragment size of 198 base pairs (bp) by MnlI digest] are associated with VC production from 112TCA dichloroelimination, whereas methanogens (190 and 307 bp) from the Methanococcales or Methanobacteriales family are associated with VC production from 12DCE hydrogenolysis. Acetate-utilizing methanogens (acetotrophs) appear to be involved in the biodegradation of VC. The relative abundance of Methanosarcinaceae, the only methanogen group with acetotrophic members, doubled in microcosms in which degradation of VC was observed. In addition, molecular analyses using primers specific for known dehalorespiring bacteria in the Dehalococcoides and Desulfuromonas groups showed the presence of these bacteria in microcosm slurry from the site that showed the highest VC production and degradation. Determination of biogeochemical controls and microbial consortia involved in TeCA degradation is leading to a better understanding of the heterogeneity in biodegradation rates and daughter product distribution in the wetland, improving capabilities for developing remediation and monitoring plans.     

Application of in situ biosparging to remediate a petroleum-hydrocarbon spill site: field and microbial evaluation

In this study, a full-scale biosparging investigation was conducted at a petroleum-hydrocarbon spill site. Field results reveal that natural attenuation was the main cause of the decrease in major contaminants [benzene, toluene, ethylbenzene, and xylenes (BTEX)] concentrations in groundwater before the operation of biosparging system. Evidence of the occurrence of natural attenuation within the BTEX plume includes: (1) decrease of DO, nitrate, sulfate, and redox potential, (2) production of dissolved ferrous iron, sulfide, methane, and CO(2), (3) decreased BTEX concentrations along the transport path, (4) increased microbial populations, and (5) limited spreading of the BTEX plume. Field results also reveal that the operation of biosparging caused the shifting of anaerobic conditions inside the plume to aerobic conditions. This variation can be confirmed by the following field observations inside the plume due to the biosparging process: (1) increase in DO, redox potential, nitrate, and sulfate, (2) decrease dissolved ferrous iron, sulfide, and methane, (3) increased total cultivable heterotrophs, and (4) decreased total cultivable anaerobes as well as methanogens. Results of polymerase chain reaction, denaturing gradient gel electrophoresis, and nucleotide sequence analysis reveal that three BTEX biodegraders (Candidauts magnetobacterium, Flavobacteriales bacterium, and Bacteroidetes bacterium) might exist at this site. Results show that more than 70% of BTEX has been removed through the biosparging system within a 10-month remedial period at an averaged groundwater temperature of 18 degrees C. This indicates that biosparging is a promising technology to remediate BTEX contaminated groundwater.     

Identification of a reactive degradation zone at a landfill leachate plume fringe using high resolution sampling and incubation techniques

Vertical small-scale variation in phenoxy acid herbicide degradation across a landfill leachate plume fringe was studied using laboratory degradation experiments. Sediment cores (subdivided into 5 cm segments) were collected in the aquifer and the sediment and porewater were used for microcosm experiments (50 experiments) and for determination of solid organic carbon, solid-water partitioning coefficients, specific phenoxy acid degraders and porewater chemistry. Results from a multi-level sampler installed next to the cores provided information on the plume position and oxygen concentration in the groundwater. Oxygen concentration was controlled individually in each microcosm to mimic the conditions at their corresponding depths. A highly increased degradation potential existed at the narrow plume fringe (37.7 to 38.6 masl), governed by the presence of phenoxy acids and oxygen. This resulted in the proliferation of a microbial population of specific phenoxy acid degraders, which further enhanced the degradation potential for phenoxy acids at the fringe. The results illustrate the importance of fringe degradation processes in contaminant plumes. Furthermore, they highlight the relevance of using high-resolution sampling techniques as well as controlled microcosm experiments in the assessment of the natural attenuation capacity of contaminant plumes in groundwater.     

Natural attenuation of chlorinated ethene compounds: model development and field-scale application at the Dover site

A multi-dimensional and multi-species reactive transport model was developed to aid in the analysis of natural attenuation design at chlorinated solvent sites. The model can simulate several simultaneously occurring attenuation processes including aerobic and anaerobic biological degradation processes. The developed model was applied to analyze field-scale transport and biodegradation processes occurring at the Area-6 site in Dover Air Force Base, Delaware. The model was calibrated to field data collected at this site. The calibrated model reproduced the general groundwater flow patterns, and also, it successfully recreated the observed distribution of tetrachloroethene (PCE), trichloroethene (TCE), dichloroethylene (DCE), vinyl chloride (VC) and chloride plumes. Field-scale decay rates of these contaminant plumes were also estimated. The decay rates are within the range of values that were previously estimated based on lab-scale microcosm and field-scale transect analyses. Model simulation results indicated that the anaerobic degradation rate of TCE, source loading rate, and groundwater transport rate are the important model parameters. Sensitivity analysis of the model indicated that the shape and extent of the predicted TCE plume is most sensitive to transmissivity values. The total mass of the predicted TCE plume is most sensitive to TCE anaerobic degradation rates. The numerical model developed in this study is a useful engineering tool for integrating field-scale natural attenuation data within a rational modeling framework. The model results can be used for quantifying the relative importance of various simultaneously occurring natural attenuation processes.     

Destruction of lindane and atrazine using stabilized iron nanoparticles under aerobic and anaerobic conditions: effects of catalyst and stabilizer

Highly stable Fe-Pd bimetallic nanoparticles were prepared with 0.2% (w/w) of sodium carboxylmethylcellulose (CMC) as a stabilizer. The effectiveness of the stabilized Fe-Pd nanoparticles was studied for degradation of two chlorinated pesticides (lindane and atrazine) under aerobic and anaerobic conditions. Batch kinetic tests showed that under anaerobic condition the nanoparticles can serve as strong electron donors and completely reduce 1 mgl(-1) of lindane at an iron dose of 0.5 gl(-1) or 1mg l(-1) of atrazine with 0.05 gl(-1) iron with a trace amount (0.05-0.8% of Fe) of Pd as a catalyst. In contrast, under aerobic condition, the nanoparticles can facilitate Fenton-like reactions, which lead to oxidation of 65% of lindane under otherwise identical conditions. Under aerobic condition, the presence of CMC reduced the level of hydroxyl radicals generated from the nanoparticels by nearly 50%, and thus, inhibited the oxidation of the contaminants. While the particle stabilization greatly enhanced the anaerobic degradation, it did not appear to be beneficial under aerobic condition. The degradation rate was progressively enhanced as the Pd content increased from 0.05% to 0.8% of Fe, and the catalytic effect of Pd was more significant under anaerobic condition. Under anaerobic condition, lindane is degraded via dihaloelimination and dehydrohalogenation, whereas atrazine is by reductive dechlorination followed by subsequent reductive dealkylation. Under aerobic condition, reactive oxygen species and hydroxyl radicals from the iron nanoparticles are responsible for oxidizing the pesticides. Lindane is oxidized via dechlorination/dehydrohalogenation, whereas atrazine is destroyed through dealkylation of the alkylamino side chain.     

Polychlorinated biphenyl (PCB) anaerobic degradation in marine sediments: microcosm study and role of autochthonous microbial communities

Polychlorobiphenyl (PCB) biodegradation was followed for 1 year in microcosms containing marine sediments collected from Mar Piccolo (Taranto, Italy) chronically contaminated by this class of hazardous compounds. The microcosms were performed under strictly anaerobic conditions with or without the addition of Dehalococcoides mccartyi, the main microorganism known to degrade PCBs through the anaerobic reductive dechlorination process. Thirty PCB congeners were monitored during the experiments revealing that the biodegradation occurred in all microcosms with a decrease in hepta-, hexa-, and penta-chlorobiphenyls (CBs) and a parallel increase in low chlorinated PCBs (tri-CBs and tetra-CBs). The concentrations of the most representative congeners detected in the original sediment, such as 245-245-CB and 2345-245-CB, and of the mixture 2356-34-CB+234-245-CB, decreased by 32.5, 23.8, and 46.7 %, respectively, after only 70 days of anaerobic incubation without any bioaugmentation treatment. Additionally, the structure and population dynamics of the microbial key players involved in the biodegradative process and of the entire mixed microbial community were accurately defined by Catalyzed Reporter Deposition Fluorescence In Situ Hybridization (CARD-FISH) in both the original sediment and during the operation of the microcosm. The reductive dehalogenase genes of D. mccartyi, specifically involved in PCB dechlorination, were also quantified using real-time PCR (qPCR). Our results demonstrated that the autochthonous microbial community living in the marine sediment, including D. mccartyi (6.32E+06 16S rRNA gene copy numbers g^?1 sediment), was able to efficiently sustain the biodegradation of PCBs when controlled anaerobic conditions were imposed.     

Biogeochemical characterisation of a coal tar distillate plume

The distillation of acidified coal tars for up to 50 years has given rise to a phenol plume approximately 500 m long, 50 m deep and containing up to 15 g l(-1) dissolved organic carbon (DOC) in the Triassic Sandstones aquifer. A conceptual biogeochemical model based on chemical and microbiological analysis of groundwater samples has been developed as a preliminary to more detailed studies of the controls on natural attenuation. While the development of redox zones and the production of methane and carbon dioxide provide evidence of natural attenuation, it appears that degradation is slow. The existence of sulphate in the plume indicates that this electron acceptor has not been depleted and that consequently methanogenesis is probably limited. Based on a simple estimate of sulphate input concentration, a half-life of about 15 years has been estimated for sulphate reduction. Geochemical modelling predicts that increased alkalinity within the plume has not led to carbonate precipitation, and thus within the limits of accuracy of the measurement, alkalinity may reflect the degree of biodegradation. This implies a loss of around 18% of the DOC over a 30-year period. Despite limited degradation, microbial studies show that there are diverse microbial communities in the aquifer with the potential for both anaerobic and aerobic biodegradation. Microbial activity was found to be greatest at the leading edge of the plume where DOC concentrations are 60 mg l(-1) or less, but activity could still be observed in more contaminated samples even though cells could not be cultured. The study suggests that degradation may be limited by the high phenol concentrations within the core of the plume, but that once diluted by dispersion, natural attenuation may proceed. More detailed studies to confirm these initial findings are identified and form the basis of associated papers.     

Mineralization of PAHs in coal-tar impacted aquifer sediments and associated microbial community structure investigated with FISH

The microbial community structure and mineralization of polycyclic aromatic hydrocarbons (PAHs) in a coal-tar contaminated aquifer were investigated spatially using fluorescence in situ hybridization (FISH) and in laboratory-scale incubations of the aquifer sediments. DAPI-detected microbial populations in the contaminated sediments were three orders of magnitude greater than nearby uncontaminated sediments, suggesting growth on coal-tar constituents in situ. Actinobacteria, beta- and gamma-Proteobacteria, and Flavobacteria dominated the in situ aerobic (>1 mg l(-1) dissolved oxygen) microbial community, whereas sulfate-reducing bacteria comprised 37% of the microbial community in the sulfidogenic region of the aquifer. Rapid mineralization of naphthalene and phenanthrene were observed in aerobic laboratory microcosms and resulted in significant enrichment of beta- and gamma-Proteobacteria potentially explaining their elevated presence in situ. Firmicutes, Flavobacteria, alpha-Proteobacteria, and Actinobacteria were also enriched in the mineralization assays, but to a lesser degree. Nitrate- and sulfate-limited mineralization of naphthalene in laboratory microcosms occurred to a small degree in aquifer sediments from locations where groundwater chemistry indicated nitrate- and sulfate-reduction, respectively. Some iron-limited mineralization of naphthalene and phenanthrene was also observed in sediments originating near groundwater measurements of elevated ferrous iron. The results of this study suggest that FISH may be a useful tool for providing a much needed link between laboratory microcosms and groundwater measurements made in situ necessary to better demonstrate the potential for natural attenuation at complex PAH contaminated sites.     

Impact of redox conditions on metolachlor and metribuzin degradation in Mississippi flood plain soils

The effect of soil redox conditions on the degradation of metolachlor and metribuzin in two Mississippi soils (Forrestdale silty clay loam and Loring silt loam) were examined in the laboratory. Herbicides were added to soil in microcosms and incubated either under oxidized (aerobic) or reduced (anaerobic) conditions. Metolachlor and metribuzin degradation under aerobic condition in the Forrestdale soil proceeded at rates of 8.83 ngd(-1) and 25 ngd(-1), respectively. Anaerobic degradation rates for the two herbicides in the Forestdale soil were 8.44 ngd(-1) and 32.5 ngd(-1), respectively. Degradation rates for the Loring soil under aerobic condition were 24.8 ngd(-1) and 12.0 ngd(-1) for metolachlor and metribuzin, respectively. Metolachlor and metribuzin degradation rates under anaerobic conditions in the Loring soil were 20.9 ngd(-1) and 5.35 ngd(-1). Metribuzin degraded faster (12.0 ngd(-1)) in the Loring soil under aerobic conditions as compared to anaerobic conditions (5.35 ngd(-1)).     

Comparison of biotic and abiotic treatment approaches for co-mingled perchlorate, nitrate, and nitramine explosives in groundwater

Biological and abiotic approaches for treating co-mingled perchlorate, nitrate, and nitramine explosives in groundwater were compared in microcosm and column studies. In microcosms, microscale zero-valent iron (mZVI), nanoscale zero-valent iron (nZVI), and nickel catalyzed the reduction of RDX and HMX from initial concentrations of 9 and 1 mg/L, respectively, to below detection (0.02 mg/L), within 2 h. The mZVI and nZVI also degraded nitrate (3 mg/L) to below 0.4 mg/L, but none of the metal catalysts were observed to appreciably reduce perchlorate ( approximately 5 mg/L) in microcosms. Perchlorate losses were observed after approximately 2 months in columns of aquifer solids treated with mZVI, but this decline appears to be the result of biodegradation rather than abiotic reduction. An emulsified vegetable oil substrate was observed to effectively promote the biological reduction of nitrate, RDX and perchlorate in microcosms, and all four target contaminants in the flow-through columns. Nitrate and perchlorate were biodegraded most rapidly, followed by RDX and then HMX, although the rates of biological reduction for the nitramine explosives were appreciably slower than observed for mZVI or nickel. A model was developed to compare contaminant degradation mechanisms and rates between the biotic and abiotic treatments.     

In situ sequential treatment of a mixed contaminant plume

Groundwater plumes often contain a mixture of contaminants that cannot easily be remediated in situ using a single technology. The purpose of this research was to evaluate an in situ treatment sequence for the control of a mixed organic plume (chlorinated ethenes and petroleum hydrocarbons) within a Funnel-and-Gate. A shallow plume located in the unconfined aquifer at Alameda Point, CA, was found to contain up to 218,000 μg/l of cis-1,2 dichloroethene (cDCE), 16,000 μg/l of vinyl chloride (VC) and <1000 μg/l of 1,1 dichloroethene (1,1 DCE), trans-1,2 dichloroethene (trans-1,2 DCE) and trichloroethene (TCE). Total benzene, toluene, ethylbenzene and xylenes (BTEX) concentrations were <10,000 μg/l. Contaminated groundwater was funneled into a gate, 3.0 m wide, 4.5 m long and 6.0 m deep (keyed into the underlying aquitard) where treatment occurred. The initial gate segment consisted of granular iron, for the reductive dechlorination of the higher chlorinated ethenes. The second segment, the biosparge zone, promoted aerobic biodegradation of petroleum hydrocarbons and any remaining lesser-chlorinated compounds, stimulated by dissolved oxygen (DO) and carbon dioxide (CO₂) additions via an in situ sparge system (CO₂ was used to neutralize the high pH produced from reactions in the iron wall). Groundwater was drawn through the gate by pumping two wells located at the sealed, downgradient, end. Over a 4-month period an estimated 1350 g of cDCE flowed into the treatment gate and the iron wall removed 1230 g, or 91% of the mass. The influent mass of VC was 572 g and the iron wall removed 535 g, corresponding to 94% mass removal. The other chlorinated ethenes had significantly lower influent masses (3 to 108 g) and the iron wall removed the majority of the mass resulting in >96% mass removal for any of the compounds. In spite of these high removal percentages, laboratory column tests indicated that at these levels of chlorinated contaminants, surface saturation of the iron grains likely contributed to lower than expected reaction rates. In the biosparge zone, mass removal of cDCE appeared to occur predominantly by biodegradation (65%) with volatilization (35%) being an important secondary process. The dominant removal process for VC was volatilization (70%) although significant biodegradation was also indicated (30%). Laboratory microcosm results confirmed the potential for aerobic biodegradation of cDCE and VC. When average influent field concentrations for cDCE and VC were 220,000 and 46,000 μg/l, respectively, the sequential treatment unit removed 99.6% of the total mass and when the influent concentrations decreased to 26,000 and 19,000 μg/l for cDCE and VC, respectively, >99.9% removal within the treatment gate was attained. BTEX compounds were found to be significantly retarded in the iron treatment zone. Although they did eventually break through the granular iron, and into the gravel transition zone, none of these compounds was detected in the biosparge zone. No noticeable interferences between the anaerobic (reductive) and aerobic parts of the system occurred during testing. The results of this experiment show that in situ treatment sequences are viable, although further work is needed to optimize performance.     

Influence of sediment on the fate and toxicity of a polyethoxylated tallowamine surfactant system (MON 0818) in aquatic microcosms

The fate and toxicity of a polyethoxylated tallowamine (POEA) surfactant system, MON 0818, was evaluated in water-sediment microcosms during a 4-d laboratory study. A surfactant solution of 8 mg l(-1) nominal concentration was added to each of nine 72-l aquaria with or without a 3-cm layer of one of two natural sediments (total organic carbon (TOC) 1.5% or 3.0%). Control well water was added to each of nine additional 72-l aquaria with or without sediment. Water samples were collected from the microcosms after 2, 6, 24, 48, 72, and 96 h of aging to conduct 48-h toxicity tests with Daphnia magna and to determine surfactant concentrations. Elevated mortality of D. magna (43-83%) was observed in overlying water sampled from water-only microcosms throughout the 96-h aging period, whereas elevated mortality (23-97%) was only observed in overlying water sampled from water-sediment microcosms during the first 24h of aging. Measured concentrations of MON 0818 in water-only microcosms remained relatively constant (4-6 mg l(-1)) during the 96-h period, whereas the concentrations in overlying water from microcosms containing either of the two types of sediment dissipated rapidly, with half-lives of 13 h in the 3.0% TOC sediment and 18 h in the 1.5% TOC sediment. Both toxicity and the concentration of MON 0818 in overlying water decreased more rapidly in microcosms containing sediment with the higher percent TOC and clay and with a higher microbial biomass. Mortality of D. magna was significantly correlated with surfactant concentrations in the overlying water. These results indicate that the toxicity of the POEA surfactant in water rapidly declines in the presence of sediment due to a reduction in the surfactant concentration in the overlying water above the sediment.     

Evaluation of TCDD biodegradability under different redox conditions

Polychlorinated dibenzo-p-dioxins have been generated as unwanted by-products in many industrial processes. Although their widespread distribution in different environmental compartments has been recognized, little is known about their fate in the ultimate environment sinks. The highly stable dioxin isomer 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) has been called the most toxic compound known to man. In this laboratory microcosm study, TCDD bioavailability was evaluated under five reduction/oxidation (redox) conditions including aerobic biodegradation, aerobic cometabolism, methanogenesis, iron reduction, and reductive dechlorination. Activated sludge and aquifer sediments from a TCDD and a pentachlorophenol (PCP) contaminated site were used as the inocula. Acetate, sludge cake, and cane molasses were used as the primary substrates (carbon sources) in cometabolism and reductive dechlorination microcosms. After a 90-day incubation period, microcosms constructed under reductive dechlorination conditions were the only treatment showing promising remediation results. The highest TCDD degradation rate [up to 86% of TCDD removal (with an initial concentration of 96 microg/kg of soil)] was observed in the microcosms with anaerobic activated sludge as the microbial inocula and sludge cakes as the primary substrates. Except for reductive dechlorination microcosms, no significant TCDD removal was observed in the microcosms prepared under other conditions. Thus, application of an effective primary substrate to enhance the reductive dechlorination process is a feasible method for TCDD bioremediation. Bioremediation expense can be significantly reduced by the supplement of some less expensive alternative substrates (e.g., sludge cakes, cane molasses). Results would be useful in designing a scale-up in situ or on-site bioremediation system such as bioslurry reactor for field application.