复合人工湿地中低浓度有机物的去除及Monod模型模拟

以复合人工湿地工程实例为研究对象,研究了其在连续5个月内对低浓度有机污染物的深度处理效果,采用简化的Monod动力学模型对研究湿地进行模拟并验证,讨论了污染负荷与去除率的相关性以及BOD/COD比值对有机污染物降解系数的影响。研究湿地总面积为5 000 m2,进水水量为860～1 560 m3/d,水力停留时间为1.48～2.69 d,水力负荷为0.17～0.31 m/d,进水中有机污染物浓度较低(BOD53.0～25.6 mg/L;COD 22.9～89.8 mg/L)。结果表明,复合湿地组合形式对BOD5和COD的去除率分别介于37.9%～79.0%和41.0%～68.7%之间,简化的Monod模型对湿地中BOD5和COD去除的预测值与实验观测值吻合程度较好;BOD5、COD的去除率分别随着进水BOD5和COD浓度的增加而增大,而增长趋势逐渐变缓,当有机污染负荷低时,模型的K值较小;低浓度有机污染物在VSF、FWS和HSF湿地中的去除效率与有机物是否容易或者缓慢被微生物降解的性质相关性较差,这可能与人工湿地中存在的其他因素促进了有机污染物的去除有关。     

美国某污水处理厂工艺设计及运行效果

介绍了美国某污水处理厂的处理工艺流程、主要构筑物构成及其设计参数,通过对该污水处理厂一年内运行效果的调研,分析评价了该污水厂的进出水水质指标;该水厂工艺流程对TSS、BOD5、COD、NH3-N、TP和浊度的年平均去除率分别可以达到97.7％、97.7％、93.5％、82.6％、95.2％和97.9％,各项出水水质均优于我国《城镇污水处理厂污染物排放标准》(GB18918-2002)一级A标准,通过对该水厂工艺的介绍和分析,为我国污水厂的建设及改造升级提供了一定的参考依据.     

Toward better understanding and feasibility of controlling greenhouse gas emissions from treatment of industrial wastewater with activated sludge

Wastewater treatment plants (WWTPs) have been recognized as important sources for anthropogenic greenhouse gas (GHG) emission. The objective of the study was to thoroughly investigate a typical industrial WWTP in southern Taiwan in winter and summer which possesses the emission factors close to those reported values, with the analyses of emission factors, mass fluxes, fugacity, lab-scale in situ experiments, and impact assessment. The activated sludge was the important source in winter and summer, and nitrous oxide (N₂O) was the main contributor (e.g., 57 to 91 % of total GHG emission in a unit of kg carbon dioxide-equivalent/kg chemical oxygen demand). Albeit important for the GHGs in the atmosphere, the fractional contribution of the GHG emission to the carbon or nitrogen removal in wastewater treatment was negligible (e.g., less than 1.5 %). In comparison with the sludge concentration or retention time, adjusting the aeration rate was more effective to diminish the GHG emission in the activated sludge without significantly affecting the treated water quality. When the aeration rate in the activated sludge simulation was reduced by 75 %, the mass flux of N₂O could be diminished by up to 53 % (from 9.6 to 4.5 mg/m²-day). The total emission in the WWTP (including carbon dioxide, methane, and N₂O) would decrease by 46 % (from 0.67 to 0.36 kg CO₂-equiv/kg COD). However, the more important benefit of changing the aeration rate was lowering the energy consumption in operation of the WWTP, as the fractional contribution of pumping to the total emission from the WWTP ranged from 46 to 93 % within the range of the aeration rate tested. Under the circumstance in which reducing the burden of climate change is a global campaign, the findings provide insight regarding the GHG emission from treatment of industrial wastewater and the associated impact on the treatment performance and possible mitigation strategies by operational modifications.

     

Micropollutant removal during biological wastewater treatment and a subsequent ozonation step

The design criteria for wastewater treatment plants (WWTP) and the sludge retention time, respectively, have a significant impact on micropollutant removal. The upgrade of an Austrian municipal WWTP to nitrogen removal (best available technology, BAT) resulted in increased elimination of most of the analyzed micropollutants. Substances, such as bisphenol-A, 17α-ethinylestradiol and the antibiotics erythromycin and roxithromycin were only removed after the upgrade of the WWTP. Nevertheless, the BAT was not sufficient to completely eliminate these compounds. Thus, a pilot scale ozonation plant was installed for additional treatment of the effluent. The application of 0.6 g O₃ g DOC⁻¹ increased the removal of most of the micropollutants, especially for compounds that were not degraded in the previous biological process, as for example carbamazepine and diclofenac. These results indicated that the ozonation of WWTP effluent is a promising technology to further decrease emissions of micropollutants from the treatment process.     

化学氧化絮凝技术在强化处理受污染河水中的应用

采用化学氧化絮凝技术(COF)对东莞市某河流的受污染河水进行处理,通过烧杯搅拌试验,考察了COF技术除污效能,在此基础上进行现场试验.结果表明,COD、BOD5、TP和NH3-N的去除率分别可达到71.2%、77.4%、91.1%和68.7%,出水指标达到了国家一级排放要求,为工程设计提供了依据.     

Performance of CSTR–EGSB–SBR system for treating sulfate-rich cellulosic ethanol wastewater and microbial community analysis

Performance and microbial community composition were evaluated in a two-phase anaerobic and aerobic system treating sulfate-rich cellulosic ethanol wastewater (CEW). The system was operated at five different chemical oxygen demand (COD)/SO₄ ²⁻ ratios (63.8, 26.3, 17.8, 13.7, and 10.7). Stable performance was obtained for total COD removal efficiency (94.5%), sulfate removal (89.3%), and methane production rate (11.5 L/day) at an organic loading rate of 32.4 kg COD/(m³·day). The acidogenic reactor made a positive contribution to net VFAs production (2318.1 mg/L) and sulfate removal (60.9%). Acidogenic bacteria (Megasphaera, Parabacteroides, unclassified Ruminococcaceae spp., and Prevotella) and sulfate-reducing bacteria (Butyrivibrio, Megasphaera) were rich in the acidogenic reactor. In the methanogenic reactor, high diversity of microorganisms corresponded with a COD removal contribution of 83.2%. Moreover, methanogens (Methanosaeta) were predominant, suggesting that these organisms played an important role in the acetotrophic methanogenesis pathway. The dominant aerobic bacteria (Truepera) appeared to have been responsible for the COD removal of the SBR. These results indicate that dividing the sulfate reduction process could effectively minimize sulfide toxicity, which is important for the successful operation of system treating sulfate-rich CEW.

     

Fenton氧化-序批式膜生物反应器耦合处理干法腈纶废水

采用Fenton氧化-序批式膜生物反应器(SBMBR)组合工艺处理干法腈纶废水。结果表明,在废水初始pH值为3.0,H2O2投加量为90.0 mmol/L,Fe2+投加量为20.0 mmol/L,反应时间为2.0 h的条件下,Fenton氧化预处理对腈纶生产废水的COD去除率达到47.0%以上,COD由1 091 mg/L降至560 mg/L,废水的BOD5/COD由0.32升至0.69,废水的可生化性得到显著提高。Fenton处理出水与丙烯腈废水等比例混合后,采用SBMBR进行生化处理,在水力停留时间为24 h,90 min缺氧/150 min好氧交替运行的条件下,COD、NH4+-N和TN的平均去除率分别为71.7%、97.2%和47.4%,碳源不足是限制TN去除效果的主要影响因素。在无外加碳源的条件下,组合工艺处理后出水COD和NH4+-N浓度分别为117 mg/L和1.7 mg/L,出水水质可以稳定达到国家一级排放标准(GB8978-1996)。     

MBBR/BAF工艺降解腈类有机物的性能研究

采用移动床生物膜反应器(MBBR)和曝气生物滤池(BAF)结合工艺对有机腈类废水处理进行了小试研究,以考察有机物的降解规律。经过稳定运行2个月,在两级硝化液回流比R=200%,pH=7.5,HRT=3 d的情况下,进水COD、CN-、NH3-N、TN及BOD5浓度平均值分别为3 024、38、185、305和845 mg/L时,出水COD、CN-、NH3-N、TN及BOD5平均浓度为50、0.5、10、45和17 mg/L,去除率分别为98.2%、98.7%、94.2%、85.2%和98.0%,BOD/COD比值由0.29提高到0.34,达到了《江苏省化学工业主要水污染物排放标准》(DB32/939-2006)一级排放标准。     

Fenton-聚硅铝铁硼处理生活垃圾压滤液研究

以正交设计方法为基础，以COD去除率为指标，确定了聚硅铝铁硼（PSAFB）最优制备条件，研究了Fenton-PSAFB混凝法处理城市生活垃圾压滤液的最优反应条件和处理效果。结果表明：以200 mL生活垃圾压滤液为处理对象，复合絮凝剂PSAFB的最优制备工艺条件为：Al/Si为1/2，Fe/Si为1/2，B/Si为1/6；其最优反应条件为：pH值为5.0，投加量为200 mg/L（以SiO₂计)；Fenton法最优反应条件为：pH值为3.0，30%H₂O₂为20 mL，1 mol/L FeSO₄为30 mL；采用最优反应条件的Fenton-PSAFB处理垃圾压滤液，浊度去除率达到95.2%，COD去除率达到84.2%，BOD₅去除率达到81.5%。     

多元微电解技术对高浓度化学清洗废水预处理的影响

以高浓度化学清洗废水为研究对象,分别考察了常规混凝沉淀、多元微电解2种工艺对有机物污染物的去除效率和改善废水可生化性的效果。结果表明:多元微电解工艺的最佳pH 3.0,填充比1∶3,微电解1 h,气水比1∶1的条件下,其对COD平均去除率可达到60%,而直接混凝沉淀仅为10.5%,多元微电解工艺能使BOD5/COD值由原来的0.12升高到0.32,提高了废水的可生化性,减轻了后续生化处理负荷,是对高浓度化学清洗废水的有效预方法。     

Flow-rate and pollution characteristics of domestic wastewater

The characteristics of the flow-rate and pollution parameters of the domestic wastewater of a medium-size city (Sivas, Turkey) have been investigated. The design and the operating parameters of a wastewater treatment plant appropriate to such a settlement were also studied. Daily and monthly flow-rate measurements and wastewater samples were taken at the outlet. Peak values of the flow-rate were observed between the hours 09:00 and 14:00. Domestic wastewater production per capita was determined as 170.6 litres per day. The wastewater biological reaction ratio coefficient (k), the BOD₅/COD ratio and the BOD₅/N ratio varied in the ranges 0.113–0.312, 0.44–0.67 and 3.1–9.5 per day, respectively. Daily pollution load parameters per capita were determined as follows: 47.3 g for BOD₅, 85.3 g for COD, 34.9 g for suspended solids, 7.9 g for nitrogen and 1.32 g for phosphorus.     

AB工艺污水厂冬季运行效果分析

对乌鲁木齐市某AB工艺污水厂冬季实际运行效果进行监测分析。结果表明：冬季水温降低不影响AB工艺对BOD₅的去除效果,BOD5的去除率平均达到88.8%,但COD和SS的去除效果下降;在A段氨氮去除率为35%,经过B段后,氨氮含量反又上升,去除率下降为7.8%左右;降低了A段除磷效果,去除率仅29%,B段则表现出稳定的除磷效果,出水总磷稳定在1.0 mg/L以下,AB工艺总磷去除率达到80%。     

Synthetic olive mill wastewater treatment by Fenton’s process in batch and continuous reactors operation

Degradation of total phenol (TPh) and organic matter, (expressed as total organic carbon TOC), of a simulated olive mill wastewater was evaluated by the Fenton oxidation process under batch and continuous mode conditions. A mixture of six phenolic acids usually found in these agro-industrial wastewaters was used for this purpose. The study focused on the optimization of key operational parameters of the Fenton process in a batch reactor, namely Fe²⁺ dosage, hydrogen peroxide concentration, pH, and reaction temperature. On the assessment of the process efficiency, > 99% of TPh and > 56% of TOC removal were attained when [Fe²⁺] = 100 ppm, [H₂O₂] = 2.0 g/L, T = 30 °C, and initial pH = 5.0, after 300 min of reaction. Under those operational conditions, experiments on a continuous stirred-tank reactor (CSTR) were performed for different space-time values (τ). TOC and TPh removals of 47.5 and 96.9%, respectively, were reached at steady-state (for τ = 120 min). High removal of COD (> 75%) and BOD₅ (> 70%) was achieved for both batch and CSTR optimum conditions; analysis of the BOD₅/COD ratio also revealed an increase in the effluent’s biodegradability. Despite the high removal of lumped parameters, the treated effluent did not met the Portuguese legal limits for direct discharge of wastewaters into water bodies, which indicates that coupled chemical-biological process may be the best solution for real olive mill wastewater treatment.     

含吡啶有机废水物化预处理工艺

对含吡啶有机废水进行分类收集,分质处理,确定了蒸发脱盐-微电解-芬顿氧化预处理工艺路线。实验表明,蒸发脱盐阶段,pH值为5时,COD去除率达62.77%;微电解阶段,pH值为4、反应时间为2.5 h时,COD去除率达24.49%;Fenton试剂氧化阶段,pH值为4,30%H2O2投加量为3.5 ml/L,Fe2+与H2O2摩尔比为1∶20,反应时间为2.5 h时,COD去除率达30.41%。经预处理,废水B/C比从0.075上升至0.48,3种特征吡啶的去除率均达到95%以上。     

椰糠填料用于人工湿地处理制胶废水

以椰糠作为湿地工作层主要填料,采用复合垂直流人工湿地处理海南天然橡胶加工业低浓度废水。结果表明,在144 mm/d水力负荷条件下,椰糠填料人工湿地对废水中的COD、BOD5、NH3-H及TP的去除率分别达到68.99%、66.49%、59.55%和75.22%,显著高于无椰糠对照组。当水力负荷提高至216 mm/d,系统运行稳定,出水水质仍能达到污水排放标准(GB 8978-1996)和《农业灌溉水质标准》(GB5084-92)。     

微电解-Fenton联合工艺预处理煤层气井压裂废水

利用Fenton强化微电解工艺对煤层气井压裂废水展开预处理研究,以COD去除率和可生化性(B/C)为考察指标,单独工艺正交实验结果表明pH为3、反应时间为90 min、铁碳体积比为1.5∶1和pH为4、反应时间为80 min、H2O2投加量为4 mL/L分别是微电解与Fenton反应的最优条件,各可获得48.1%和44.9%的COD去除率。在最优条件下进行微电解-Fenton联合运行实验,连续61 h内COD去除率均稳定在65%以上,B/C由0.158上升到0.3以上,有利于后续生化处理的运行。     

PACT工艺处理PAM生产废水的实验研究

采用粉末活性炭活性污泥工艺(PACT)处理经凹凸棒土预处理后的聚丙烯酰胺(PAM)生产废水。实验考察了粉末活性炭(PAC)的投加对活性污泥处理系统的影响,并探讨了PAC投加量、曝气时间、水力停留时间等参数对降解反应的影响。结果表明:PAC的投加能提高水中溶解氧的利用率,改善污泥沉降性能,增强活性污泥系统对有机物的去除效果;在PAC投加量500 mg/L、曝气10 h的条件下,PACT工艺对PAM生产废水的处理效果良好,COD的去除率为80.8%,BOD5去除率为83.8%,丙烯酰胺(AM)去除率为84.2%。     

UASB处理硫酸盐有机废水的启动

为了考察上流式厌氧污泥床反应器(UASB)处理含硫酸盐有机废水的特性,采用有效容积为10 L的UASB,研究了启动运行过程中COD和SO2-4降解情况、出水VFA和pH值、产气量及颗粒污泥比产甲烷活性(SMA)变化状况。结果表明,接种厌氧颗粒污泥,保持进水COD为1 500 mg/L,SO2-4浓度为100 mg/L,将HRT由24 h缩短至12 h以提高负荷,经历55 d成功启动了UASB反应器;当HRT为12 h,进水COD和SO2-4负荷为3.0 kg/(m3·d)和0.20 kg/(m3·d),COD和SO2-4的去除率分别达到80%和89%,出水VFA为3 mmol/L,产气量达9.5 L/d,颗粒污泥的SMA为86.4 mL/(g VSS·d)。     

酵母菌处理马铃薯淀粉废水研究

马铃薯淀粉废水属高浓度废水,COD达到30 000 mg/L左右,BOD为15 000 mg/L左右,可生化性较好。针对废水中主要含有淀粉、蛋白质和可溶性纤维等成分,筛选分离出能降解这些有机成分的6种酵母。以废水为培养液分别培养这6种酵母及其混合菌,实验结果表明,各酵母菌株对该废水都有较好的降解效果,混合菌的处理效果要好于单个菌株。在连续流废水培养条件下,混合酵母活性和菌体量也较高,MLSS稳定在12 g/L左右,其COD去除率稳定在77%左右。     

模糊综合评价在氧化沟能耗评价中的应用

在对环太湖流域4座采用氧化沟工艺的城市污水处理厂进行能耗调研的基础上,以吨水位能耗(E)、生化段装机容量(η)、有机物去除量(ΔCOD)、氨氮去除量(ΔNH3-N)、总磷去除量(ΔTP)作为评价氧化沟法城市污水厂能耗的指标,结合隶属度函数,应用单因素模糊综合评价法对所调研的污水处理厂进行能耗水平定量评价。得出A污水处理厂的能耗级别为二级,B和C污水处理厂的能耗级别为三级,D污水处理厂能耗级别为五级。级别越高能耗越大。