The contemporary European silver cycle

This paper examines the 1-year anthropogenic stocks and flows of silver as it progresses from extraction to final disposal on the European continent. The primary flows of silver include production, fabrication and manufacturing, use, and waste management. A substance flow analysis (SFA) was used to trace the flows and inventory data, and mass balance equations were used to determine the quantity of flows. The results reveal that Europe has a low level of silver mine production (1580 Mg Ag/year) and instead relies on silver imports and the recycling of scrap in production and fabrication. In the year 1997, Europe imported 1160 Mg Ag of ore concentrate and 2010 Mg Ag of refined silver, and recycled 2750 Mg Ag of new and old scrap. There is a net addition of 3320 Mg Ag/year into silver reservoirs at the use stage. This is the result of a greater amount of silver entering the system from manufacturing than is leaving the system into waste management. The waste flow with the highest content of silver is municipal solid waste, which contains 1180 Mg Ag/year. In total, 62% of all discarded silver is recycled and 38% is sent to landfills. The results of this study and other element and material flow analyses can help guide resource managers, environmental policy makers, and environmental scientists in their efforts to increase material recovery and recycling, address resource sustainability, and ameliorate environmental problems.     

Historical evolution of anthropogenic aluminum stocks and flows in Italy

Dynamic stocks and flows analysis was applied to the anthropogenic aluminum cycle in Italy in order to detect and quantify metal flows and in-use stocks over the years 1947–2009. The model utilized a top-down approach, including data for production, consumption, loss, and trade flows of aluminum. Seven end-use markets were considered, namely buildings and construction, transportation, consumer durables, machinery and equipment, electrical engineering, containers and packaging, and miscellaneous appliance types. The results of this dynamic stocks and flows analysis model quantified the contemporary anthropogenic reservoirs (or in-use stocks) of aluminum at about 320 kg per capita, mainly embedded within the transportation and building and construction sectors. Cumulative in-use stock represents approximately 11 years of supply at current usage rates (about 20 Mt versus 1.7 Mt/year), implying significant potential for recycling in the future as this stock comes out of use. Flow analysis revealed that Italy imports mainly unwrought aluminum and exports final products, while the main material losses occur during alumina refining and collection of old scrap: specifically, containers and packaging have the highest old scrap generation rate, but for the lowest recovery rate (50%). Increasing support to collection of scrap and initiatives oriented to aluminum recovery specifically would allow Italy to increase its reliance on domestic material, and may also allow a decline of the country import-dependence on primary sources. The dynamic stocks and flows model created here provides a quantitative historical record of the aluminum required by Italian society during important periods of development and provides guidance for future decision-making around the use of domestic secondary resources.     

Steel all over the world: Estimating in-use stocks of iron for 200 countries

Industrialization and urbanization in the developing world have boosted steel demand during the recent two decades. Reliable estimates on how much steel is required for high economic development are necessary to better understand the future challenges for employment, resource management, capacity planning, and climate change mitigation within the steel sector. During their use phase, steel-containing products provide service to people, and the size of the in-use stock of steel can serve as an indicator of the total service level. We apply dynamic material flow analysis to estimate in-use stocks of steel in about 200 countries and identify patterns of how stocks evolve over time. Three different models of the steel cycle are applied and a full uncertainty analysis is conducted to obtain reliable stock estimates for the period 1700–2008.Per capita in-use stocks in countries with a long industrial history, e.g., the U.S, the UK, or Germany, are between 11 and 16 tons, and stock accumulation is slowing down or has come to a halt. Stocks in countries that industrialized rather recently, such as South Korea or Portugal, are between 6 and 10 tons per capita and grow fast. In several countries, per capita in-use stocks of steel have saturated or are close to saturation. We identify the range of saturation to be 13 ± 2 tons for the total per capita stock, which includes 10 ± 2 tons for construction, 1.3 ± 0.5 tons for machinery, 1.5 ± 0.7 tons for transportation, and 0.6 ± 0.2 tons for appliances and containers. The time series for the stocks and the saturation levels can be used to estimate future steel production and scrap supply.     

Linking energy scenarios with metal demand modeling–The case of indium in CIGS solar cells

Some renewable energy technologies rely on the functionalities provided by geochemically scarce metals. One example are CIGS solar cells, an emerging thin film photovoltaic technology, which contain indium. In this study we model global future indium demand related to the implementation of various energy scenarios and assess implications for the supply system. Influencing parameters of the demand model are either static or dynamic and include technology shares, technological progress and handling in the anthroposphere. Parameters’ levels reflect pessimistic, reference, and optimistic development. The demand from other indium containing products is roughly estimated. For the reference case, the installed capacity of CIGS solar cells ranges from 12 to 387 GW in 2030 (31–1401 GW in 2050), depending on the energy scenario chosen. This translates to between 485 and 15,724 tonnes of primary indium needed from 2000 to 2030 (789–30,556 tonnes through 2050). One scenario exemplifies that optimistic assumptions for technological progress and handling in the anthroposphere can reduce cumulative primary indium demand by 43% until 2050 compared to the reference case, while with pessimistic assumptions the demand increases by about a factor of five. To meet the future indium demand, several options to increase supply are discussed: (1) expansion of zinc metal provision (indium is currently a by-product of zinc mining), (2) improving extraction efficiency, (3) new mining activities where indium is a by-product of other metals and (4) mining of historic residues. Potential future constraints and environmental impacts of these supply options are also briefly discussed.     

The Austrian P budget as a basis for resource optimization

Phosphorus (P) is a finite and non-substitutable resource that is essential to sustaining high levels of agricultural productivity but is also responsible for environmental problems, e.g., eutrophication. Based on the methodology of Material Flow Analysis, this study attempts to quantify all relevant flows and stocks of phosphorus (P) in Austria, with a special focus on waste and wastewater management. The system is modeled with the software STAN, which considers data uncertainty and applies data reconciliation and error propagation. The main novelty of this work lies in the high level of detail at which flows and stocks have been quantified to achieve a deeper understanding of the system and to provide a sound basis for the evaluation of various management options. The budget confirms on the one hand the dependence of mineral P fertilizer application (2 kg cap⁻¹ yr⁻¹), but it highlights on the other hand considerable unexploited potential for improvement. For example, municipal sewage sludge (0.75 kg cap⁻¹ yr⁻¹) and meat and bone meal (0.65 kg cap⁻¹ yr⁻¹) could potentially substitute 70% of the total applied mineral P fertilizers. However, recycling rates are low for several P flows (e.g., 27% of municipal sewage sludge; 3% of meat and bone meal). Therefore, Austria is building up a remarkable P stock (2.1 kg P cap⁻¹ yr⁻¹), mainly due to accumulation in landfills (1.1 kg P cap⁻¹ yr⁻¹) and agricultural soils (0.48 kg P cap⁻¹ yr⁻¹).     

Energy and carbon dioxide intensity of Thailand's steel industry and greenhouse gas emission projection toward the year 2050

The purpose of this article is to study the energy and carbon dioxide intensities of Thailand's steel industry and to propose greenhouse gas emission trends from the year 2011 to 2050 under plausible scenarios. The amount of CO₂ emission from iron and steel production was calculated using the 2006 Intergovernmental Panel on Climate Change (IPCC) guidelines in the boundary of production process (gate to gate). The results showed that energy intensity of semi-finished steel product was 2.84 GJ/t semi-finished steel and CO₂ intensity was 0.37 tCO_2eq/t semi-finished steel. Energy intensity of steel finishing process was 1.86 GJ/t finished steel and CO₂ intensity was 0.16 tCO_2eq/t finished steel. Using three plausible scenarios from Thailand's steel industry, S1: without integrated steel plant (baseline scenario), S2: with a traditional integrated BF–BOF route and S3: with an alternative integrated DR-EAF route; the Greenhouse Gas emissions from the year 2011 to 2050 were projected. In 2050, the CO₂ emission from S1 (baseline scenario) was 4.84 million tonnes, S2 was 21.96 million tonnes increasing 4.54 times from baseline scenario. The CO₂ emission from S3 was 7.12 million tonnes increasing 1.47 times from baseline scenario.     

In-depth analysis of aluminum flows in Austria as a basis to increase resource efficiency

Based on the method of material flow analysis (MFA), a static model of Austrian aluminum (Al) flows in 2010 was developed. Extensive data research on Al production, consumption, trade and waste management was conducted and resulted in a detailed model of national Al resources. Data uncertainty was considered in the model based on the application of a rigorous concept for data quality assessment. The model results indicated that the growth of the Austrian “in-use” Al stock amounts to 11 ± 3.1 kg yr⁻¹ cap⁻¹. The total “in-use” Al stock was determined using a bottom-up approach, which produced an estimate of 260 kg Al cap⁻¹. Approximately 7 ± 1 kg of Al yr⁻¹ cap⁻¹ of old scrap was generated in 2010, of which 20% was not recovered because of losses in waste management processes. Quantitatively, approximately 40% of the total scrap input to secondary Al production originated from net imports, highlighting the import dependency of Austrian Al refiners and remelters. Uncertainties in the calculation of recycling indicators for the Austrian Al system with high shares of foreign scrap trade were exemplarily illustrated for the old scrap ratio (OSR) in secondary Al production, resulting in a possible range of OSRs between 0 and 66%. Overall, the detailed MFA in this study provides a basis to identify resource potentials as well as resource losses in the national Al system, and it will serve as a starting point for a dynamic Al model to be developed in the future.     

Environmental consequences of recycling aluminum old scrap in a global market

Nowadays, aluminum scrap is traded globally. This has increased the need to analyze the flows of aluminum scrap, as well as to determine the environmental consequences from aluminum recycling. The objective of this work is to determine the greenhouse gases (GHG) emissions of the old scrap collected and sorted for recycling, considering the market interactions. The study focused on Spain as a representative country for Europe. We integrate material flow analysis (MFA) with consequential life cycle assessment (CLCA) in order to determine the most likely destination for the old scrap and the most likely corresponding process affected. Based on this analysis, it is possible to project some scenarios and to quantify the GHG emissions (generated and avoided) associated with old scrap recycling within a global market. From the MFA results, we projected that the Spanish demand for aluminum products will be met mainly with an increase in primary aluminum imports, and the excess of old scrap not used in Spain will be exported in future years, mainly to Asia. Depending on the scenario and on the marginal source of primary aluminum considered, the GHG emission estimates varied between −18,140 kg of CO₂ eq. t⁻¹ and −8427 of CO₂ eq. t⁻¹ of old scrap collected. More GHG emissions are avoided with an increase in export flows, but the export of old scrap should be considered as the loss of a key resource, and in the long term, it will also affect the semifinished products industry. Mapping the flows of raw materials and waste, as well as quantifying the GHG impacts derived from recycling, has become an essential prerequisite to consistent development from a linear toward a circular economy (CE).     

Airborne manganese concentrations on the Korean peninsula from 1991 to 2006

In this study, the distribution of airborne manganese (Mn) bound with particulate matters (PM) was investigated using data sets collected from 15 major cities in Korea over a 16-year time span (1991–2006). The mean Mn concentration measured from all the major cities in Korea throughout the entire study period was 71 ng m^?3, while the annual mean values of different cities ranged from 10.5 ng m^?3 in Yeosu (2003) to 615 ng m^?3 in Wonju (2006). The Mn levels were considerably larger in industrialized areas than in other land-use types. The Mn concentrations in the major industrial cities of Pohang, Incheon, and Ansan averaged 255, 98.2, and 84.6 ng m^?3, respectively; these values were far higher than those measured typically at most cities, e.g., 20–60 ng m^?3. Seasonal patterns characterized by the peak occurrence in spring and the noticeable drop in summer reflected the effects of the massive PM inflow from China (spring) and effective washout by summer monsoon in East Asia, respectively. Examination of Mn data over a long-term period indicated that the temporal trends of Mn seen in most cities were fairly constant through time since the 1990s, although some abnormalities were observed in cities of strong man-made activities (e.g., Pohang and Wonju). In light of the severity of airborne Mn pollution in many urban areas, it is desirable to establish an abatement strategy that can help effectively reduce Mn levels.     

Quantification and spatial characterization of in-use copper stocks in Shanghai

Shanghai is the largest industrial and commercial city of China, where in-use stocks of metals are likely to be significant. The in-use stocks of copper in this city are thus established by an extensive “bottom-up” study. Spatial distribution of copper stocks within Shanghai has further been characterized for better understanding of copper utilization pattern of this city. For the year 2012, the results are a total stock of 914.6 Gg Cu, and 38.4–64.1 kg Cu per capita. Nearly 94% of copper stocks distribute in subcategories of electric power transmission and distribution, water transmission and distribution, buildings, and household durable. Features of spatial distribution show that three central districts of Jing An, Hong Kou and Huang Pu have the spatial density of more than 1 Gg/km². And Chong Ming county and Jin Shan District have the lowest spatial density of about 0.01 Gg/km². It has been found that the copper stock density within Shanghai is largely determined by population density and economic development level.     

Current results and future perspectives for Japanese recycling of home electrical appliances

The Japanese system of recycling home electrical appliances has several unique aspects, including (1) a limited number of target appliances, (2) a recycling fee system that requires consumers to pay a recycling fee at the time of disposal, and (3) a direct recycling obligation for manufacturers, who have a physical, rather than a financial, responsibility for their end-of-life products. We studied data from 2001 to 2007 and found that the amount of four specified home electrical appliances and their materials that was recycled increased from about 319,249 tonnes in 2001 to about 447,262 tonnes—or 3.5 kg per inhabitant—in 2006. Recycling yield and development of recycling technologies have also improved. New recycling technologies have enabled a higher rate of material recycling of plastics (i.e., a closed-loop recycling). Improved eco-design, such as design for easier disassembly, has been promoted, and the higher quality of discarded appliances has enhanced the reuse market. Hazardous substances and fluorocarbons are being well managed. Problems with the recycling system include inelastic recycling fees, illegal dumping, illegal transfer by retailers, and the limited number of target appliances. Recycling fees could be reduced; this move might reduce the incidence of illegal dumping, as would engage stakeholders in collaborative efforts against illegal dumping. Illegal transfers could be reduced by improved traceability for retailers. Products such as liquid crystal displays, plasma display panels and clothes dryers have become increasingly common and should be also be targeted for recycling.     

A comparison of on-site nutrient and energy recycling technologies in algal oil production

Research on biofuel production pathways from algae continues because among other potential advantages they avoid key consequential effects of terrestrial oil crops, such as competition for cropland. However, the economics, energetic balance, and climate change emissions from algal biofuels pathways do not always show great potential, due in part to high fertilizer demand. Nutrient recycling from algal biomass residue is likely to be essential for reducing the environmental impacts and cost associated with algae-derived fuels. After a review of available technologies, anaerobic digestion (AD) and hydrothermal liquefaction (HTL) were selected and compared on their nutrient recycling and energy recovery potential for lipid-extracted algal biomass using the microalgae strain Scenedesmus dimorphus. For 1 kg (dry weight) of algae cultivated in an open raceway pond, 40.7 g N and 3.8 g P can be recycled through AD, while 26.0 g N and 6.8 g P can be recycled through HTL. In terms of energy production, 2.49 MJ heat and 2.61 MJ electricity are generated from AD biogas combustion to meet production system demands, while 3.30 MJ heat and 0.95 MJ electricity from HTL products are generated and used within the production system.Assuming recycled nutrient products from AD or HTL technologies displace demand for synthetic fertilizers, and energy products displace natural gas and electricity, the life cycle greenhouse gas reduction achieved by adding AD to the simulated algal oil production system is between 622 and 808 g carbon dioxide equivalent (CO₂e)/kg biomass depending on substitution assumptions, while the life cycle GHG reduction achieved by HTL is between 513 and 535 g CO₂e/kg biomass depending on substitution assumptions. Based on the effectiveness of nutrient recycling and energy recovery, as well as technology maturity, AD appears to perform better than HTL as a nutrient and energy recycling technology in algae oil production systems.     

Estimating rainforest biomass stocks and carbon loss from deforestation and degradation in Papua New Guinea 1972–2002: Best estimates,uncertainties and research needs

Reduction of carbon emissions from tropical deforestation and forest degradation is being considered a cost-effective way of mitigating the impacts of global warming. If such reductions are to be implemented, accurate and repeatable measurements of forest cover change and biomass will be required. In Papua New Guinea (PNG), which has one of the world's largest remaining areas of tropical forest, we used the best available data to estimate rainforest carbon stocks, and emissions from deforestation and degradation. We collated all available PNG field measurements which could be used to estimate carbon stocks in logged and unlogged forest. We extrapolated these plot-level estimates across the forested landscape using high-resolution forest mapping. We found the best estimate of forest carbon stocks contained in logged and unlogged forest in 2002 to be 4770 Mt (±13%). Our best estimate of gross forest carbon released through deforestation and degradation between 1972 and 2002 was 1178 Mt (±18%). By applying a long-term forest change model, we estimated that the carbon loss resulting from deforestation and degradation in 2001 was 53 Mt (±18%), rising from 24 Mt (±15%) in 1972. Forty-one percent of 2001 emissions resulted from logging, rising from 21% in 1972. Reducing emissions from logging is therefore a priority for PNG. The large uncertainty in our estimates of carbon stocks and fluxes is primarily due to the dearth of field measurements in both logged and unlogged forest, and the lack of PNG logging damage studies. Research priorities for PNG to increase the accuracy of forest carbon stock assessments are the collection of field measurements in unlogged forest and more spatially explicit logging damage studies.     

Watershed-scale assessment of arsenic and metal contamination in the surface soils surrounding Miyun Reservoir,Beijing, China

Concentrations of As and selected metals were determined in surface soils of the Miyun Reservoir watershed of Beijing, China. The degree to which concentrations of As and metals exceeded the corresponding background concentration of soils was: Cr > Cu > Zn > As > Ni with no apparent anthropogenic contamination with Cd and Pb. Based on the results of a combination of multivariate statistics and geostatistical analysis, greater concentrations of Cr and Ni in soils were determined to be primarily from iron ore mining near where the Chaohe River enters the northeast portion of the reservoir. Agricultural activities were responsible for the observed elevated concentrations of Cu and Zn in soils. Relatively great concentrations of As were found in soils near the upstream regions of the Baihe River in Chicheng County where small gold mining activities have taken place. The greatest potential for adverse effects of Cr and Cu occurred along the eastern shore of Miyun Reservoir.     

Global anthropogenic selenium cycles for 1940–2010

Selenium plays an important role in emerging thin film solar energy technologies. As solar energy is expected to have a larger share in the world's future energy portfolio, the long-term availability of selenium becomes a potential concern, yet no global cycles have ever been generated. In this work, the global cycles, stocks, and flows of selenium are characterized for the entire time period 1940–2010 by using principles of material flow analysis (MFA). The cycles present information on the production, fabrication and manufacturing, use, and resource management stages during that period. The results of the analysis show that during 1940–2010 approximately 90 Gg of refined selenium was produced and entered into fabrication and manufacturing worldwide. 60 Gg of this amount (two-thirds!) was dissipated into the environment through end-uses such as chemicals, pigments, glass manufacturing, metallurgical additives, and fertilizer and feed additives. The in-use stock of selenium is estimated at 2.7 Gg as of 2010. Because of data limitations such as proprietary and withheld information, these figures represent informed estimates rather than exact values. Selenium can be recovered from end-of-life electrical and electronic equipment, while for other end-uses recycling is difficult or impossible. One of the ways to buttress supplies of selenium for future technologies would be to deploy recycling schemes for photovoltaics as well as other electronics applications.     

A preliminary investigation of the efficacy of riparian fencing schemes for reducing contributions from eroding channel banks to the siltation of salmonid spawning gravels across the south west UK

The low productivity of salmonids in many river systems across the UK is testament to their intolerance of water quality perturbations including those associated with excessive sedimentation. Catchment and fishery managers concerned with combating such issues require reliable information on the key sources of the sediment problem to target management and on the efficacy of the mitigation options being implemented. In recognition of the latter requirement, a pre- and post-remediation sediment sourcing survey was used to examine the potential for using sediment tracing to assemble preliminary information on the efficacy of riparian fencing schemes for reducing sediment contributions from eroding channel banks to salmonid spawning gravels in the Rivers Camel, Fal, Lynher, Plym, Tamar and Tavy in the south west of the UK. Respective estimates of the overall mean proportion (±95% confidence limits) of the interstitial sediment input to salmonid spawning gravels originating from eroding channel banks during the pre- (1999–2000) and post-remediation (2008–2009) study periods were computed at 97 ± 1% vs. 69 ± 1%, 94 ± 1% vs. 91 ± 1%, 12 ± 1% vs. 10 ± 1%, 92 ± 1% vs. 34 ± 1%, 31 ± 1% vs. 16 ± 1% and 90 ± 1% vs. 66 ± 1%. Whilst the study demonstrates the potential utility of the fingerprinting approach for helping to assemble important information on the efficacy of bank fencing as a sediment source control measure at catchment scale, a number of limitations of the work and some suggestions for improving experimental design are discussed. Equivalent data are urgently required for many sediment mitigation options to help inform the development of water quality policy packages designed to protect aquatic ecosystems.     

Transfer characteristics of cobalt from soil to crops in the suburban areas of Fujian Province,southeast China

The bioavailability of cobalt and its transfer from soil to vegetables and rice were investigated. Among 312 soils collected from vegetable and paddy fields in the suburban areas of some major cities of Fujian Province, southeast China, total soil Co ranged from 3.5 to 21.7 mg kg^?1, indicating a slight accumulation compared with the background value of the province. DTPA extracted 0.1–8.5% of soil total Co. Total and DTPA-extractable Co correlated with soil pH, CEC, free Fe, total Mn, clay and silt content more significantly in paddy soils than in the soils from vegetable fields. The average Co concentrations in the edible parts of vegetables and rice were 15.4 μg kg^?1 and 15.5 μg kg^?1, respectively. The transfer factor (the ratio of plant Co to soil DTPA-extractable Co, TF_DTPA) ranged from 0.003 to 0.126 with a median of 0.049. The TF_DTPA decreased in the order of leafy vegetables > fruit vegetables > root vegetables > rice. The TF_DTPA of all crops decreased with increasing DTPA-extractable Co. Increase in pH, CEC, organic matter, clay, silt, free iron and total Mn limited the soil-to-plant transfer of Co to varying degrees. The transfer of Co from the soils to the edible parts of the crops was lower than that of Zn, Cu and Cd, but higher than that of Pb in the same areas. The concentrations of Co in rice and vegetables in the study areas were considered to be safe for the local residents because of the slight anthropogenic input and the low transfer potential to the edible parts of Co from the soils.     

Closed loop recycling of plastics containing Flame Retardants

Annually 2.7 million tonnes of plastics containing Flame Retardants (FRs) are globally discarded in Waste Electrical and Electronic Equipment (WEEE). Little is known on the feasibility of closing material loops for FR plastics. Therefore, series of experiments were set up to analyze the feasibility of separating plastics containing FRs from one specific product category, namely End-of-Life (EoL) Liquid Crystal Display (LCD) TVs. The characterization of the housings of this waste stream indicated a concentration of 18 wt% Bromine based (Br) FRs and 31 wt% Phosphor based (P) FRs, the remainder not containing FRs. With practical tests it was demonstrated that, after disassembly and plastic identification, the co-polymer poly-carbonate (PC)/acrylonitrile-butadiene-styrene (ABS) containing PFR can be recycled in a closed loop system. Based on the determined plastic density distributions and separation efficiencies of optical sorters, a purity of 82% was calculated for PFR PC/ABS separated from EoL LCD TVs after size-reduction (shredding). Performed miscibility tests indicated that for this fraction at least a factor 10 dilution with virgin material is required. In addition, higher waste volumes are required for a size-reduction based treatment to become economically viable and technical challenges still need to be faced, whereas closed loop recycling of PFR PC/ABS from the current waste stream of EoL LCD TVs of different brands in a disassembly based treatment is found to be technically feasible and economically viable under European boundary conditions.     

Municipal solid waste management in China: Status,problems and challenges

This paper presents an examination of MSW generation and composition in China, providing an overview of the current state of MSW management, an analysis of existing problems in MSW collection, separation, recycling and disposal, and some suggestions for improving MSW systems in the future. In China, along with urbanization, population growth and industrialization, the quantity of municipal solid waste (MSW) generation has been increasing rapidly. The total MSW amount increased from 31.3 million tonnes in 1980 to 212 million tonnes in 2006, and the waste generation rate increased from 0.50 kg/capita/day in 1980 to 0.98 kg/capita/year in 2006. Currently, waste composition in China is dominated by a high organic and moisture content, since the concentration of kitchen waste in urban solid waste makes up the highest proportion (at approximately 60%) of the waste stream. The total amount of MSW collected and transported was 148 million tonnes in 2006, of which 91.4% was landfilled, 6.4% was incinerated and 2.2% was composted. The overall MSW treatment rate in China was approximately 62% in 2007. In 2007, there were 460 facilities, including 366 landfill sites, 17 composing plants, and 66 incineration plants. This paper also considers the challenges faced and opportunities for MSW management in China, and a number of recommendations are made aimed at improving the MSW management system.     

Management and recycling of waste glass in concrete products: Current situations in Hong Kong

Disposal of more than 300 tonnes waste glass daily derived from post-consumer beverage bottles is one of the major environmental challenges for Hong Kong, and this challenge continues to escalate as limited recycling channels can be identified and the capacity of valuable landfill space is going to be saturated at an alarming rate. For this reason, in the past ten years, a major research effort has been carried out at The Hong Kong Polytechnic University to find practical ways to recycle waste glass for the production of different concrete products such as concrete blocks, self-compacting concrete and architectural mortar. Some of these specialty glass-concrete products have been successfully commercialized and are gaining wider acceptance. This paper gives an overview of the current management and recycling situation of waste glass and the experience of using recycled waste glass in concrete products in Hong Kong.