Energy balances,greenhouse gas emissions and economics of biochar production from palm oil empty fruit bunches

This paper presents results from a gate-to-gate analysis of the energy balance, greenhouse gas (GHG) emissions and economic efficiency of biochar production from palm oil empty fruit bunches (EFB). The analysis is based on data obtained from EFB combustion in a slow pyrolysis plant in Selangor, Malaysia. The outputs of the slow pyrolysis plant are biochar, syngas, bio-oil and water vapor. The net energy yield of the biochar produced in the Selangor plant is 11.47 MJ kg⁻¹ EFB. The energy content of the biochar produced is higher than the energy required for producing the biochar, i.e. the energy balance of biochar production is positive. The combustion of EFB using diesel fuel has the largest energy demand of 2.31 MJ kg⁻¹ EFB in the pyrolysis process. Comparatively smaller amounts of energy are required as electricity (0.39 MJ kg⁻¹ EFB) and for transportation of biochar to the warehouse and the field (0.13 MJ kg⁻¹ EFB). The net greenhouse gas emissions of the studied biochar production account for 0.046 kg CO₂-equiv. kg⁻¹ EFB yr⁻¹ without considering fertilizer substitution effects and carbon accumulation from biochar in the soil. The studied biochar production is profitable where biochar can be sold for at least 533 US-$ t⁻¹. Potential measures for improvement are discussed, including higher productivity of biochar production, reduced energy consumption and efficient use of the byproducts from the slow pyrolysis.     

The Austrian P budget as a basis for resource optimization

Phosphorus (P) is a finite and non-substitutable resource that is essential to sustaining high levels of agricultural productivity but is also responsible for environmental problems, e.g., eutrophication. Based on the methodology of Material Flow Analysis, this study attempts to quantify all relevant flows and stocks of phosphorus (P) in Austria, with a special focus on waste and wastewater management. The system is modeled with the software STAN, which considers data uncertainty and applies data reconciliation and error propagation. The main novelty of this work lies in the high level of detail at which flows and stocks have been quantified to achieve a deeper understanding of the system and to provide a sound basis for the evaluation of various management options. The budget confirms on the one hand the dependence of mineral P fertilizer application (2 kg cap⁻¹ yr⁻¹), but it highlights on the other hand considerable unexploited potential for improvement. For example, municipal sewage sludge (0.75 kg cap⁻¹ yr⁻¹) and meat and bone meal (0.65 kg cap⁻¹ yr⁻¹) could potentially substitute 70% of the total applied mineral P fertilizers. However, recycling rates are low for several P flows (e.g., 27% of municipal sewage sludge; 3% of meat and bone meal). Therefore, Austria is building up a remarkable P stock (2.1 kg P cap⁻¹ yr⁻¹), mainly due to accumulation in landfills (1.1 kg P cap⁻¹ yr⁻¹) and agricultural soils (0.48 kg P cap⁻¹ yr⁻¹).     

Watershed-scale assessment of arsenic and metal contamination in the surface soils surrounding Miyun Reservoir,Beijing, China

Concentrations of As and selected metals were determined in surface soils of the Miyun Reservoir watershed of Beijing, China. The degree to which concentrations of As and metals exceeded the corresponding background concentration of soils was: Cr > Cu > Zn > As > Ni with no apparent anthropogenic contamination with Cd and Pb. Based on the results of a combination of multivariate statistics and geostatistical analysis, greater concentrations of Cr and Ni in soils were determined to be primarily from iron ore mining near where the Chaohe River enters the northeast portion of the reservoir. Agricultural activities were responsible for the observed elevated concentrations of Cu and Zn in soils. Relatively great concentrations of As were found in soils near the upstream regions of the Baihe River in Chicheng County where small gold mining activities have taken place. The greatest potential for adverse effects of Cr and Cu occurred along the eastern shore of Miyun Reservoir.     

In-depth analysis of aluminum flows in Austria as a basis to increase resource efficiency

Based on the method of material flow analysis (MFA), a static model of Austrian aluminum (Al) flows in 2010 was developed. Extensive data research on Al production, consumption, trade and waste management was conducted and resulted in a detailed model of national Al resources. Data uncertainty was considered in the model based on the application of a rigorous concept for data quality assessment. The model results indicated that the growth of the Austrian “in-use” Al stock amounts to 11 ± 3.1 kg yr⁻¹ cap⁻¹. The total “in-use” Al stock was determined using a bottom-up approach, which produced an estimate of 260 kg Al cap⁻¹. Approximately 7 ± 1 kg of Al yr⁻¹ cap⁻¹ of old scrap was generated in 2010, of which 20% was not recovered because of losses in waste management processes. Quantitatively, approximately 40% of the total scrap input to secondary Al production originated from net imports, highlighting the import dependency of Austrian Al refiners and remelters. Uncertainties in the calculation of recycling indicators for the Austrian Al system with high shares of foreign scrap trade were exemplarily illustrated for the old scrap ratio (OSR) in secondary Al production, resulting in a possible range of OSRs between 0 and 66%. Overall, the detailed MFA in this study provides a basis to identify resource potentials as well as resource losses in the national Al system, and it will serve as a starting point for a dynamic Al model to be developed in the future.     

Greening of production in metal processing industry through process modifications and improved management practices

Although it was indicated through various studies from around the world that resource efficiency can be adapted in metal processing plants, a very limited number of projects could be realized in Turkish metal processing industry so far. In this study it was aimed at investigating process modifications and management practices to increase water and chemical use efficiency thus increasing environmental and economic performance of a metal processing company. As a result of the applications in heat treatment and zinc phosphating processes total water consumption of the company was reduced by 34.1% corresponding to an annual water saving of 18,831 m³. Moreover, total chemical consumption in zinc phosphating as one of the most chemical intensive processes in the company, was decreased by 1401 kg/year (26.1%). Applications in zinc phosphating process led to a significant decrease in the amount of treated wastewater and wastewater treatment sludge which is labelled as hazardous waste according to national legislations. Total wastewater generation was decreased by 3255 m³/year (50.9%) while wastewater treatment sludge was reduced 4656 kg/year (16.9%). Moreover, energy consumption of the company was reduced by 32.647 kW h/year which corresponds to 36% energy saving in water pumping. Implementation cost of the applications were 34,233$ which is calculated to be paid back in 2.3 years. This study is expected to fill a gap in Turkey by demonstrating that environmental performance in metal processing industry could be improved by process modifications and improved management practices resulting in tangible economic gains.     

Storage and characterization of cotton gin waste for ethanol production

In 2002, about 17.1 million bales of cotton were ginned in the United States and the estimated cotton gin waste was 2.25 × 10⁹ kg. The disposal of cotton gin waste (CGW) is a significant problem in the cotton ginning industry, but CGW could be potentially used as feedstock for bioethanol. Freshly discharged CGW and stored CGW were characterized for storage stability and potential for ethanol production by determining their summative compositions. The bulk densities of the fresh wet and dry CGW were 210.2 ± 59.9 kg m⁻³ and 183.3 ± 52.2 kg m⁻³, respectively. After six months of storage the volume of piles A, B, and C decreased by 38.7%, 41.5%, and 33.3%, respectively, relative to the volume of the pile at the start of the storage. The ash content of the CGW was very high ranging from 10% to 21% and the acid-insoluble fraction was high (21–24%). The total carbohydrate content was very low and ranged from 34% to 49%. After three months storage, chemical compositional analysis showed the loss of total carbohydrates was minimal but after six months, the losses were as high as 25%. This loss of carbohydrates suggests that under open storage conditions, the feedstock must be processed within three months to reduce ethanol yield losses.     

Linking energy scenarios with metal demand modeling–The case of indium in CIGS solar cells

Some renewable energy technologies rely on the functionalities provided by geochemically scarce metals. One example are CIGS solar cells, an emerging thin film photovoltaic technology, which contain indium. In this study we model global future indium demand related to the implementation of various energy scenarios and assess implications for the supply system. Influencing parameters of the demand model are either static or dynamic and include technology shares, technological progress and handling in the anthroposphere. Parameters’ levels reflect pessimistic, reference, and optimistic development. The demand from other indium containing products is roughly estimated. For the reference case, the installed capacity of CIGS solar cells ranges from 12 to 387 GW in 2030 (31–1401 GW in 2050), depending on the energy scenario chosen. This translates to between 485 and 15,724 tonnes of primary indium needed from 2000 to 2030 (789–30,556 tonnes through 2050). One scenario exemplifies that optimistic assumptions for technological progress and handling in the anthroposphere can reduce cumulative primary indium demand by 43% until 2050 compared to the reference case, while with pessimistic assumptions the demand increases by about a factor of five. To meet the future indium demand, several options to increase supply are discussed: (1) expansion of zinc metal provision (indium is currently a by-product of zinc mining), (2) improving extraction efficiency, (3) new mining activities where indium is a by-product of other metals and (4) mining of historic residues. Potential future constraints and environmental impacts of these supply options are also briefly discussed.     

Characterization of pollutants in Florida street sweepings for management and reuse

Disposal and beneficial-use options for street sweeping residuals collected as part of routine roadway maintenance activities in Florida, USA, were assessed by characterizing approximately 200 samples collected from 20 municipalities. Total concentrations (mg/kg or μg/kg) and leachable concentrations (mg/L or μg/L) of 11 metals and a number of organic pollutant groups (volatile organics, semi-volatile organics, pesticides, herbicides, carbamates) in the samples were measured. The synthetic precipitation leaching procedure (SPLP) was performed to evaluate the leachability of the pollutants. From the total metal analysis, several metals (e.g., arsenic, barium, chromium, copper, nickel, lead, and zinc) were commonly found above their detection limits. Zinc was found to have the highest mean concentration of all metals measured (46.7 mg/kg), followed by copper (10.7 mg/kg) and barium (10.5 mg/kg). The metal with the smallest mean concentration was arsenic (0.48 mg/kg). A small fraction of the total arsenic, barium, lead, and zinc leached in some samples using the SPLP; leached concentrations were relatively low. A few organic compounds (e.g., 4,4′-DDT, endrin, and endosulfan II) were detected in a limited number of samples. When the total and leaching results were compared to risk-based Florida soil cleanup target levels and groundwater cleanup target levels, the street sweepings were not found to pose a significant human-health risk via direct exposure or groundwater contamination.     

Subsoil TPH contamination in two oil pipeline pumping stations and one pipeline right-of-way in north Mexico

This investigation deals with the characterization carried out in zones around two pipeline pumping stations and one pipeline right-of-way in the north of Mexico. In particular those areas where contamination was evaluated: (a) south area of the separation ditch in the Avalos station, (b) the area between the separation ditch at the Avalos station, (c) km 194 + 420 of the Moctuzma station, and (d) km 286 + 900 in the Candelaria station. Results of this investigation showed that only four samples showed TPH values higher than the Mexican limit for 2004: AVA 1B, with 21,191 mg kg^?1; AVA 1C, with 9348 mg kg^?1; AVA 2B, with 13,970 mg kg^?1; and MOC 2A, with 4108 mg kg^?1.None of the sampled points showed the presence of PAHs at values higher than those found in the Mexican or American legislations. PAH were detected in the range of 0.0004 and 13.05 mg kg^?1.It is suggested to implement surfactant soil washing as a remediation technique for the approximately 600 m³ that need to be treated.     

Lead accumulation in different Chinese cabbage cultivars and screening for pollution-safe cultivars

Recently, the concept of pollution-safe cultivars (PSCs) was proposed to minimize the influx of pollutants to the human food chain. Variations in lead (Pb) uptake and translocation among Chinese cabbage (Brassica pekinensis L.) cultivars were investigated in a pot-culture experiment and a field-culture experiment to screen out Pb-PSCs for food safety. The results of the pot-culture experiment showed that shoot Pb concentrations under two Pb treatments (500 and 1500 mg kg^?1) varied significantly (p < 0.05) between cultivars, with average values of 3.01 and 6.87 mg kg^?1, respectively. Enrichment factors (EFs) and translocation factors (TFs) in cultivars were less than 0.50 and varied significantly (p < 0.05) between cultivars. Shoot Pb concentrations in 12 cultivars under treatment T₁ (500 mg kg^?1) were lower than 2.0 mg kg^?1. The field-culture experiment further confirmed Qiuao, Shiboqiukang and Fuxing 80 as Pb-PSCs, which were suitable to be cultivated in low-Pb (<382.25 mg kg^?1) contaminated soils and harmless to human health as foods.     

Seasonal variation of municipal solid waste generation and composition in four East European cities

The quality of recyclable and residual municipal solid waste (MSW) is, among other factors, strongly influenced by the seasonal variation in MSW composition. However, a relatively marginal amount of published data on seasonal MSW composition especially in East European countries do not provide sufficient information on this phenomenon. This study provides results from municipal waste composition research campaigns conducted during the period of 2009–2011 in four cities of Eastern European countries (Lithuania, Russia, Ukraine and Georgia). The median monthly MSW generation values ranged from 18.70 in Kutaisi (Georgia) to 38.31 kg capita⁻¹ month⁻¹ in Kaunas (Lithuania). The quantitative estimation of seasonal variation was performed by fitting the collected data to time series forecasting models, such as non-parametric seasonal exponential smoothing, Winters additive, and Winters multiplicative methods.     

Butyltin occurrence and risk assessment in the sediments of the Iberian Peninsula

The occurrence of butyltin (BT) compounds in more than 50 recent sediment samples of the Iberian Peninsula, collected in the harbours of the western Mediterranean Sea (Spain) and the North Atlantic Ocean (Portugal), including domestic and industrial sewage disposal sites, has been assessed. The highest levels of tributyltin (TBT) (7673 μg kg^?1 dry wt.) were detected in commercial harbours associated with inputs from large vessels. However, relatively high TBT values (about 2150 μg kg^?1 dry wt.) were also detected in fishing and recreational boating areas. Spanish marinas and harbours are more polluted in terms of TBT (5–7673 μg kg^?1 dry wt.) compared to those in Portugal (4–12 μg kg^?1 dry wt.). Generally, the Mediterranean sediments show a BT distribution characterized by the predominance of TBT over the degradation products dibutyl (DBT) and monobutyltin (MBT), indicating the presence of recent inputs, in contrast to the Portuguese coastal distribution. Calculation of butyltin degradation indexes (BDI) confirmed a different trend, depending on the area. Furthermore, a comparative study of the occurrence of BT in different sewage sludge disposal sites shows that domestic primary sewage sludge effluents can contribute to coastal BT pollution, but to a lesser extent when compared with harbours. Historical trends (1995–2003) for Barcelona harbour reveal that BT regulations on the use of TBT-based antifouling paints have not been fully effective. Finally, a comparison against the existing sediment quality guidelines (SQGs) indicated that acute toxic effects could only be expected for TBT in some Mediterranean harbours; conversely, in every North Atlantic Ocean station, a lesser environmental threat for the harbour benthic community is expected.     

Nitrogen critical loads and management alternatives for N-impacted ecosystems in California

Empirical critical loads for N deposition effects and maps showing areas projected to be in exceedance of the critical load (CL) are given for seven major vegetation types in California. Thirty-five percent of the land area for these vegetation types (99,639 km²) is estimated to be in excess of the N CL. Low CL values (3–8 kg N ha^?1 yr^?1) were determined for mixed conifer forests, chaparral and oak woodlands due to highly N-sensitive biota (lichens) and N-poor or low biomass vegetation in the case of coastal sage scrub (CSS), annual grassland, and desert scrub vegetation. At these N deposition critical loads the latter three ecosystem types are at risk of major vegetation type change because N enrichment favors invasion by exotic annual grasses. Fifty-four and forty-four percent of the area for CSS and grasslands are in exceedance of the CL for invasive grasses, while 53 and 41% of the chaparral and oak woodland areas are in exceedance of the CL for impacts on epiphytic lichen communities. Approximately 30% of the desert (based on invasive grasses and increased fire risk) and mixed conifer forest (based on lichen community changes) areas are in exceedance of the CL. These ecosystems are generally located further from emissions sources than many grasslands or CSS areas. By comparison, only 3–15% of the forested and chaparral land areas are estimated to be in exceedance of the NO₃^? leaching CL. The CL for incipient N saturation in mixed conifer forest catchments was 17 kg N ha^?1 yr^?1. In 10% of the CL exceedance areas for all seven vegetation types combined, the CL is exceeded by at least 10 kg N ha^?1 yr^?1, and in 27% of the exceedance areas the CL is exceeded by at least 5 kg N ha^?1 yr^?1. Management strategies for mitigating the effects of excess N are based on reducing N emissions and reducing site N capital through approaches such as biomass removal and prescribed fire or control of invasive grasses by mowing, selective herbicides, weeding or domestic animal grazing. Ultimately, decreases in N deposition are needed for long-term ecosystem protection and sustainability, and this is the only strategy that will protect epiphytic lichen communities.     

Farmland damage and its impact on the overlapped areas of cropland and coal resources in the eastern plains of China

The subsidence caused by coal mining in areas where cropland and coal resources overlap in the eastern plains of China with high ground water levels has caused large amounts of water to collect in cropland, significant damage to cropland, and a sharp contradiction between people and land distribution within this region. Systematic analysis and calculation were conducted on these areas by using GIS spatial overlay analysis technology, subsidence and occupied cropland estimation models, and crop yield reduction prediction model to reveal the overlapped characteristics and extent of farmland damage, as well as to evaluate the effects of farmland damage to grain yield, farmland landscape, agricultural population, and dynamical equilibrium of the total cultivated land. Results showed that the overlapped areas of cropland and coal resources on the eastern plains of China occupied an area covering 1.33 × 10⁵ km², which accounted for 31.93% of the total cropland area. In 2020, the accumulative total area of destroyed cropland reached 3.83 × 10³ km², thus reducing grain yield by 9.63 × 10⁸ kg, and increasing the number of landless farmers to 1.91 × 10⁶. Furthermore, the quality and production capacity of cultivated land decreased, farmland landscape patterns changed, land patterns and structures were adjusted, the dynamical equilibrium of the total cultivated land was difficult to guarantee, and social instability increased in coal mining subsidence areas. These findings provided a scientific basis for relevant government departments to enact countermeasures for the coordinative production of coal and grain.     

Transfer characteristics of cobalt from soil to crops in the suburban areas of Fujian Province,southeast China

The bioavailability of cobalt and its transfer from soil to vegetables and rice were investigated. Among 312 soils collected from vegetable and paddy fields in the suburban areas of some major cities of Fujian Province, southeast China, total soil Co ranged from 3.5 to 21.7 mg kg^?1, indicating a slight accumulation compared with the background value of the province. DTPA extracted 0.1–8.5% of soil total Co. Total and DTPA-extractable Co correlated with soil pH, CEC, free Fe, total Mn, clay and silt content more significantly in paddy soils than in the soils from vegetable fields. The average Co concentrations in the edible parts of vegetables and rice were 15.4 μg kg^?1 and 15.5 μg kg^?1, respectively. The transfer factor (the ratio of plant Co to soil DTPA-extractable Co, TF_DTPA) ranged from 0.003 to 0.126 with a median of 0.049. The TF_DTPA decreased in the order of leafy vegetables > fruit vegetables > root vegetables > rice. The TF_DTPA of all crops decreased with increasing DTPA-extractable Co. Increase in pH, CEC, organic matter, clay, silt, free iron and total Mn limited the soil-to-plant transfer of Co to varying degrees. The transfer of Co from the soils to the edible parts of the crops was lower than that of Zn, Cu and Cd, but higher than that of Pb in the same areas. The concentrations of Co in rice and vegetables in the study areas were considered to be safe for the local residents because of the slight anthropogenic input and the low transfer potential to the edible parts of Co from the soils.     

Environmental resource footprinting of drug manufacturing: Effects of scale-up and tablet dosage

The formulation and scale-up of batch processes is one of the major challenges in the development of pharmaceutical dosage forms and at the same time a significant resource demanding process which is generally overlooked in environmental sustainability assessments. First, this paper proposes general trends in the experience curve of cumulative resource consumption of pharmaceutical tablet manufacturing of PREZISTA^® 800 mg through wet granulation (WG) at four consecutive scales in both R&D and manufacturing environments (resp. WG1 = 1 kg/h, WG5 = 5 kg/h, WG30 = 30 kg/h and WG240 = 240 kg/h). Second, the authors aim at evaluating the environmental impact from a life cycle perspective of a daily consumption of PREZISTA^® 2× 400 mg tablets versus the bioequivalent PREZISTA^® 800 mg tablet which was launched to enhance patient compliance. Environmental sustainability assessment was conducted at three different system boundaries, which enables identification, localization and eventually reduction of burdens, in this case natural resource extraction. Exergy Analysis (EA) was used at process level (α) and plant level (β) while a cradle-to-gate Exergetic Life Cycle Assessment (ELCA) was conducted at the overall industrial level (γ) by means of the CEENE method (Cumulative Exergy Extraction from the Natural Environment). Life cycle stages taken into account are Active Pharmaceutical Ingredient (API) production, Drug Product (DP) production and Packaging. At process level (α), the total resource extraction for the manufacturing of one daily dose of PREZISTA^® (800 mg tablet) amounted up to 0.44 MJ_ex at the smallest scale (WG1) while this amount proved to be reduced by 58%, 79% and 83% at WG5, WG30 and WG240 respectively. Expanding the boundaries to the overall industrial level (γ) reveals that the main resource demand is at the production of the Active Pharmaceutical Ingredient (API), excipients, packaging materials and cleaning media used in DP production. At the largest scale (WG240) the use of cleaning media during DP production contributes considerably less to the total resource extraction. Overall, the effect of scale-up and learning on resource consumption during DP production showed to possess a power-law experience curve y = 2.40 * x^−0.57 when shifting from WG1 (smallest lab scale) to WG240 (industrial manufacturing). Tablet dosage (2× 400 mg versus 1× 800 mg) did not significantly affect the absolute environmental burden. However, the relative contribution of resource categories did change due to the different production technology. It could be concluded that in meeting social and economic demands by launching the PREZISTA^® 800 mg tablet, no trade-off in environmental burden occurred. On the long term, future research should strive to take into account R&D processes and all services related to pipeline activities taking place prior to market launch and eventually to allocate impacts to the final product.     

Application of polyacrylamide to reduce phosphorus losses from a Chinese purple soil: A laboratory and field investigation

Use of anionic polyacrylamide (PAM) to control phosphorus (P) losses from a Chinese purple soil was studied in both a laboratory soil column experiment and a field plot experiment on a steep slope (27%). Treatments in the column study were a control, and PAM mixed uniformly into the soil at rates of 0.02, 0.05, 0.08, 0.10, and 0.20%. We found that PAM had an important inhibitory effect on vertical P transport in the soil columns, with the 0.20% PAM treatment having the greatest significant reduction in leachate soluble P concentrations and losses resulting from nine leaching periods. Field experiments were conducted on 5 m wide by 21 m long natural rainfall plots, that allowed collection of both surface runoff and subsurface drainage water. Wheat was planted and grown on all plots with typical fertilizer applied. Treatments included a control, dry PAM at 3.9 kg ha^?1, dry PAM at 3.9 kg ha^?1 applied together with lime (CaCO₃ at 4.9 t ha^?1), and dry PAM at 3.9 kg ha^?1 applied together with gypsum (CaSO₄·2H₂O at 4 t ha^?1). Results from the field plot experiment in which 5 rainfall events resulted in measurable runoff and leachate showed that all PAM treatments significantly reduced runoff volume and total P losses in surface runoff compared to the control. The PAM treatments also all significantly reduced water volume leached to the tile drain. However, total P losses in the leachate water were not significantly different due to the treatments, perhaps due to the low PAM soil surface application rate and/or high experimental variability. The PAM alone treatment resulted in the greatest wheat growth as indicated by the plant growth indexes of wheat plant height, leaf length, leaf width, grain number per head, and dried grain mass. Growth indexes of the PAM with Calcium treatments were significantly lesser. These results indicate that the selection and use of soil amendments need to be carefully determined based upon the most important management goal at a particular site (runoff/nutrient loss control, enhanced plant growth, or a combination).     

Analytical solution for Joule–Thomson cooling during CO2 geo-sequestration in depleted oil and gas reservoirs

Mathematical tools are needed to screen out sites where Joule–Thomson cooling is a prohibitive factor for CO₂ geo-sequestration and to design approaches to mitigate the effect. In this paper, a simple analytical solution is developed by invoking steady-state flow and constant thermophysical properties. The analytical solution allows fast evaluation of spatiotemporal temperature fields, resulting from constant-rate CO₂ injection. The applicability of the analytical solution is demonstrated by comparison with non-isothermal simulation results from the reservoir simulator TOUGH2. Analysis confirms that for an injection rate of 3 kg s^?1 (0.1 MT yr^?1) into moderately warm (>40 °C) and permeable formations (>10^?14 m² (10 mD)), JTC is unlikely to be a problem for initial reservoir pressures as low as 2 MPa (290 psi).     

CO2 capture from power plants: Part II. A parametric study of the economical performance based on mono-ethanolamine

While the demand for reduction in CO₂ emission is increasing, the cost of the CO₂ capture processes remains a limiting factor for large-scale application. Reducing the cost of the capture system by improving the process and the solvent used must have a priority in order to apply this technology in the future. In this paper, a definition of the economic baseline for post-combustion CO₂ capture from 600 MW_e bituminous coal-fired power plant is described. The baseline capture process is based on 30% (by weight) aqueous solution of monoethanolamine (MEA). A process model has been developed previously using the Aspen Plus simulation programme where the baseline CO₂-removal has been chosen to be 90%. The results from the process modelling have provided the required input data to the economic modelling. Depending on the baseline technical and economical results, an economical parameter study for a CO₂ capture process based on absorption/desorption with MEA solutions was performed.Major capture cost reductions can be realized by optimizing the lean solvent loading, the amine solvent concentration, as well as the stripper operating pressure. A minimum CO₂ avoided cost of € 33 tonne⁻¹ CO₂ was found for a lean solvent loading of 0.3 mol CO₂/mol MEA, using a 40 wt.% MEA solution and a stripper operating pressure of 210 kPa. At these conditions 3.0 GJ/tonne CO₂ of thermal energy was used for the solvent regeneration. This translates to a € 22 MWh⁻¹ increase in the cost of electricity, compared to € 31.4 MWh⁻¹ for the power plant without capture.     

Biological treatment of anaerobically digested palm oil mill effluent (POME) using a Lab-Scale Sequencing Batch Reactor (SBR)

The production of highly polluting palm oil mill effluent (POME) has resulted in serious environmental hazards. While anaerobic digestion is widely accepted as an effective method for the treatment of POME, anaerobic treatment of POME alone has difficulty meeting discharge limits due to the high organic strength of POME. Hence, subsequent post-treatment following aerobic treatment is vital to meet the discharge limits. The objective of the present study is to investigate the aerobic treatment of anaerobically digested POME by using a sequencing batch reactor (SBR). The SBR performance was assessed by measuring Chemical Oxygen Demand (COD), Biochemical Oxygen Demand (BOD) and Total Suspended Solids (TSS) removal as well as Sludge Volume Index (SVI). The operating pH and dissolved oxygen concentrations were found to be 8.25–9.14 and 1.5–6.4 mg/L, respectively, throughout the experiment. The experimental results demonstrate that MLVSS, OLR and sludge loading rate (SLR) play a significant role in the organic removal efficiency of SBR systems and therefore, further investigation on these parameters was conducted to attain optimum SBR performance. Maximum COD (95–96%), BOD (97–98%) and TSS (98–99%) removal efficiencies were achieved at optimum OLR, SLR and MLVSS concentration ranges of 1.8–4.2 kg COD/m³ day, 2.5–4.6 kg TSS/m³ day and 22,000–25,000 mg/L, respectively. The effluent quality remained stable and complied with the discharge limit. At the same time, the sludge showed good settling properties with average SVI of 65. It is envisaged that the SBR process could complement the anaerobic treatment to produce final treated effluent which meets the discharge limit.