Mobility of adsorbed arsenic in two calcareous soils as influenced by water extract of compost

The mobility of arsenic (As) in soil affects both the bio-toxicity of As and the groundwater quality, which in turn indirectly affects the quality of edible part of crops and human health, if the crops were irrigated with As contaminated groundwater. A vertical soil column simulates the depth of a soil profile in a real soil environment. Thus soil column experiment is much more pertinent to soil environment than a batch experiment to simulate solute movement as well as leaching through soil profile. A laboratory soil column experiment was conducted to determine the extent of As leaching from soil percolated with influent that contained organic substances. The water extract of compost (WEC) was used as the source of organic substances. The results of As breakthrough curves (BTCs) showed that less pore volumes of influents were required to reach the relative concentration ratio of 1 (C/C0=1) for the two calcareous soils treated with influent that contained WEC. The concentrations of As in the column effluents of soils percolated with 0.01M KCl in WEC were significantly higher than those percolated with 0.01M KCl with the same volumes of effluents collected. This clearly indicates that dissolved as well as deprotonated organic substances which are negatively charged have higher potential for competing the adsorption sites with As on soils, leading to increasing mobility of As in soil and associated environments. Further, it is observed that the characteristics of soil components related to As adsorption affected the adsorption as well as desorption processes and subsequent mobility of As in soil environment as influenced by organic substances.     

Soil attenuation of As(III,V) and Se(IV,VI) seepage potential at ash disposal facilities

Leachate from ash landfills is frequently enriched with As and Se but their off-site movement is not well understood. The attenuation potential of As and Se by soils surrounding selected landfills during leachate seepage was investigated in laboratory column studies using simulated ash leachate. As(III, V) and Se(IV, VI) concentrations as well as pH, flow rate, and a tracer were monitored in influent and effluent for up to 800 pore volumes followed by sequential desorption, extraction, and digestion of column segments. Column breakthrough curves (BTCs) were compared to predictions based on previously measured sorption isotherms. Early As(V) breakthrough and retarded As(III) breakthrough relative to predicted BTCs are indicative of oxidative transformation during seepage. For Se(VI), which exhibits linear sorption and the lowest sorption propensity, measured BTCs were predicted fairly well by equilibrium sorption isotherms, except for the early arrival of Se(IV) in one site soil, which in part, may be due to higher column pH values compared to batch isotherms. Most of the As and Se retained by soils during leaching was found to be strongly sorbed (60–90%) or irreversibly bound (10–40%) with <5% readily desorbable. Redox potential favoring transformation to the more sorptive valence states of As(V) and Se(IV) will invoke additional attenuation beyond equilibrium sorption-based predictions. With the exception of Se(IV) on one site soil, results indicate that attenuation by down-gradient soils of As and Se in ash landfill seepage will often be no less than what is predicted by equilibrium sorption capacity with further attenuation expected due to favorable redox transformation processes, thus mitigating contaminant plumes and associated risks.     

Second-order modeling of arsenite transport in soils

Rate limited processes including kinetic adsorption-desorption can greatly impact the fate and behavior of toxic arsenic compounds in heterogeneous soils. In this study, miscible displacement column experiments were carried out to investigate the extent of reactivity during transport of arsenite in soils. Arsenite breakthrough curves (BTCs) of Olivier and Windsor soils exhibited strong retardation with diffusive effluent fronts followed by slow release or tailing during leaching. Such behavior is indicative of the dominance of kinetic retention reactions for arsenite transport in the soil columns. Sharp decrease or increase in arsenite concentration in response to flow interruptions (stop-flow) further verified that non-equilibrium conditions are dominant. After some 40-60 pore volumes of continued leaching, 30-70% of the applied arsenite was retained by the soil in the columns. Furthermore, continued arsenite slow release for months was evident by the high levels of residual arsenite concentrations observed during leaching. In contrast, arsenite transport in a reference sand material exhibited no retention where complete mass recovery in the effluent solution was attained. A second-order model (SOM) which accounts for equilibrium, reversible, and irreversible retention mechanisms was utilized to describe arsenite transport results from the soil columns. Based on inverse and predictive modeling results, the SOM model successfully depicted arsenite BTCs from several soil columns. Based on inverse and predictive modeling results, a second-order model which accounts for kinetic reversible and irreversible reactions is recommended for describing arsenite transport in soils.     

Determination of bromacil transport as a function of water and carbon content in soils

This study was conducted to determine the significance of bromacil transport as a function of water and carbon content in soils and to explore the implications of neglecting sorption when making assessments of travel time of bromacil through the vadose zone. Equilibrium batch sorption tests were performed for loamy sand and sandy soil added with four different levels of powdered activated carbon (PAC) content (0, 0.01, 0.05, and 0.1%). Column experiments were also conducted at various water and carbon contents under steady-state flow conditions. The first set of column experiments was conducted in loamy sand containing 1.5% organic carbon under three different water contents (0.23, 0.32, and 0.41) to measure breakthrough curves (BTCs) of bromide and bromacil injected as a square pulse. In the second set of column experiments, BTCs of bromide and bromacil injected as a front were measured in saturated sandy columns at the four different PAC levels given above. Column breakthrough data were analyzed with both equilibrium and nonequilibrium (two-site) convection-dispersion equation (CDE) models to determine transport and sorption parameters under various water and carbon contents. Analysis with batch data indicated that neglect of the partition-related term in the calculation of solute velocity may lead to erroneous estimation of travel time of bromacil, i.e. an overestimation of the solute velocity by a factor of R. The column experiments showed that arrival time of the bromacil peak was larger than that of the bromide peak in soils, indicating that transport of bromacil was retarded relative to bromide in the observed conditions. Extent of bromacil retardation (R) increased with decreasing water content and increasing PAC content, supporting the importance of retardation in the estimation of travel time of bromacil even at small amounts of organic carbon for soils with lower water content.     

Leaching of heavy metals from contaminated soils using EDTA

Ethylenediaminetetraacetic acid (EDTA) extraction of Zn, Cd, Cu and Pb from four contaminated soils was studied using batch and column leaching experiments. In the batch experiment, the heavy metals extracted were virtually all as 1:1 metal-EDTA complexes. The ratios of Zn, Cd, Cu and Pb of the extracted were similar to those in the soils, suggesting that EDTA extracted the four heavy metals with similar efficiency. In contrast, different elution patterns were obtained for Zn, Cd, Cu and Pb in the column leaching experiment using 0.01 M EDTA. Cu was either the most mobile or among the most mobile of the four heavy metals, and its peak concentration corresponded with the arrival of full strength EDTA in the leachate. The mobility of Zn and Cd was usually slightly lower than that of Cu. Pb was the least mobile, and its elution increased after the peaks of Cu and Zn. Sequential fractionations of leached and un-leached soils showed that heavy metals in various operationally defined fractions contributed to the removal by EDTA. Considerable mobilisation of Fe occurred in two of the four soils during EDTA leaching. Decreases in the Fe and Mn oxide fraction of heavy metals after EDTA leaching occurred in both soils, as well as in a third soil that showed little Fe mobilisation. The results suggest that the lability of metals in soil, the kinetics of metal desorption/dissolution and the mode of EDTA addition were the main factors controlling the behaviour of metal leaching with EDTA.     

The influence of organic ligands on the retention of lead in soil

Organic acids are commonly produced and exuded by plant roots and soil microorganisms. Some of these organic compounds are effective chelating agents and have the potential to enhance metal mobility. The effect of citrate and salicylate on the leaching of lead in soil was investigated in a laboratory experiment. In short-term batch experiments, adsorption of lead to soil was slightly enhanced with increasing salicylate concentration (500-5000 microM) but decreased significantly in the presence of citrate. These observations suggested that citrate may enhance Pb leaching, but this was not observed in the column study. Soluble Pb in the presence and absence citrate or salicylate (up to 5000 microM) was added to soil columns at a moderate flow rate, but no Pb was observed to emerge from the soil in any of the soil columns. Rapid biodegradation of citrate in soil eliminated potential complexing ability. Breakthrough of Pb from soil was noted only when using small columns at high flow rates (>20 pore volumes per day). Under these conditions of physical and chemical non-equilibrium, citrate was not degraded and significantly enhanced Pb mobility. As in the batch adsorption experiments, the presence of salicylate reduced Pb leaching. Considering the extreme conditions required to induce Pb leaching, it is likely that Pb will remain relatively immobile in soil even in the presence of a strong complexing agent such as citrate.     

Enhanced retention of linuron, alachlor and metalaxyl in sandy soil columns intercalated with wood barriers

A study has been made of the effect a reactive barrier made of pine (softwood) or oak (hardwood) wood intercalated in a sandy soil column has on the retention of linuron, alachlor and metalaxyl (pesticides with contrasting physicochemical characteristics). The leaching of pesticides has been carried out under a saturated flow regime and breakthrough curves (BTCs) have been obtained at flow rates of 1 mL min⁻¹ (all pesticides) and 3 mL min⁻¹ (linuron). The cumulative curves in the unmodified soil indicate a leaching of pesticides >80% of the total amount of compound added. After barrier intercalation, linuron leaching decreases significantly and a modification of the leaching kinetics of alachlor and metalaxyl has been observed. The theoretical R factors increased ∼2.6-3.3, 1.2-1.6-fold, and 1.4-1.7-fold and the concentration of the maximum peak decreased ∼6-12-fold, 2-4-fold and 1.2-2-fold for linuron, alachlor and metalaxyl, respectively. When considering the three pesticides, significant correlations have been found between the theoretical retardation factor (R) and the pore volume corresponding to the maximum peaks of the BTCs (r = 0.77; p < 0.05) or the total volume leached (r = −0.78; p < 0.05). The results reveal the efficacy of reactive wood barriers to decrease the leaching of pesticides from point sources of pollution depends on the type of wood, the hydrophobicity of the pesticide and the adopted water flow rate. Pine was more effective than oak in decreasing the leaching of hydrophobic pesticide linuron or in decreasing the maximum peak concentration of the less hydrophobic pesticides in soils. Efficacy of these wood barriers was limited for the least hydrophobic pesticide metalaxyl.     

Changes in pesticide adsorption with time at high soil to solution ratios

Adsorption of six pesticides (2,4-D, dicamba, fluroxypyr, fluazifop-P, metsulfuron-methyl and flupyrsulfuron-methyl) in nine contrasting soils was measured using two techniques: (i) a classical batch method and (ii) a centrifugation method that allowed the measurement of adsorption at a realistic soil to solution ratio after one and seven days. Although the batch method gived significantly higher values of Kd than the centrifugation method for the more strongly sorbed molecules in the more sorptive soils, it tended to give lower adsorption coefficients compared to the centrifugation method when adsorption was lower. Discrepancies between the two methods were probably mainly due to the vigorous shaking applied in the batch technique that artificially enhances the availability of adsorption sites. This implies that shortly after application, more pesticide may be present in the soil solution and thus be available for degradation, plant uptake or leaching than will be predicted from adsorption coefficient determined using the batch method. Adsorption significantly increased between one and seven days and the extractability of total residues decreased with time. The increase in adsorption was not directly related to the level of adsorption although it was more important in soils containing more organic carbon (p=0.022). These results confirm the importance of time-dependent processes and the necessity to include them in risk assessment procedures. The centrifugation technique is a useful method to measure adsorption of pesticides at realistic soil moisture contents and seems to be an adequate technique to characterise the fraction of pesticide that is available for leaching at a given time after application.     

Adsorption and transport of arsenate in carbonate-rich soils: coupled effects of nonlinear and rate-limited sorption

The transport and fate of arsenate in carbonate-rich soil under alkaline conditions was investigated with multiple approaches combining batch, sequential extraction and column experiments as well as transport modeling studies. Batch experiments indicated that sorption isotherm was nonlinear over a wide range of concentration (0.1-200 mg L(-1)) examined. As(V) adsorption to the calcareous soil was initially fast but then continued at a slower rate, indicating the potential effect of rate-limited sorption on transport. Column experiments illustrated that transport of As(V) was significantly retarded compared to a non-reactive tracer. The degree of retardation decreased with increasing As(V) concentration. As(V) breakthrough curves exhibited nonideal transport behavior due to the coupled effects of nonlinear and rate-limited sorption on arsenate transport, which is consistent with the results of modeling studies. The contribution of nonlinear sorption to the arsenate retardation was negligible at low concentration but increased with increasing As(V) concentration. Sequential extraction results showed that nonspecifically sorbed (easily exchangeable, outer sphere complexes) fraction of arsenate is dominant with respect to the inner-sphere surface bound complexes of arsenate in the carbonate soil fraction, indicating high bioavailability and transport for arsenate in the carbonate-rich soils of which Fe and Al oxyhydroxide fractions are limited.     

Transport of Escherichia coli through variably saturated sand columns and modeling approaches

A sand column leaching system with well-controlled suction and flow rate was built to investigate the effects on bacterial transport of air-water interface effects (AWI) correlated to water content, particle size, and column length. Adsorption of Escherichia coli strain D to silica sands was measured in batch tests. The average % adsorption for coarse and fine sands was 45.9+/-7.8% and 96.9+/-3.2%, respectively. However, results from static batch adsorption experiments have limited applicability to dynamic bacterial transport in columns. The early breakthrough of E. coli relative to bromide was clear for all columns, namely c. 0.15 to 0.3 pore volume earlier. Column length had no significant effects on the E. coli peak concentration or on total recovery in leachate, indicating retention in the top layer of sands. Tailing of breakthrough curves was more prominent for all fine sand columns than their coarse sand counterparts. Bacterial recovery in leachate from coarse and saturated sand columns was significantly higher than from fine and unsaturated columns. Observed data were fitted by the convection-dispersion model, amended for one-site and two-site adsorption to particles, and for air-water interface (AWI) adsorption. Among all models, the two-site+AWI model achieved consistently high model efficiency for all experiments. Thus it is evident from experimental and modeling results that AWI adsorption plays an important role in E. coli transport in sand columns.     

Effects of compost and phosphate amendments on arsenic mobility in soils and arsenic uptake by the hyperaccumulator,Pteris vittata L

Chinese brake fern (Pteris vittata L.), an arsenic (As) hyperaccumulator, has shown the potential to remediate As-contaminated soils. This study investigated the effects of soil amendments on the leachability of As from soils and As uptake by Chinese brake fern. The ferns were grown for 12 weeks in a chromated-copper-arsenate (CCA) contaminated soil or in As spiked contaminated (ASC) soil. Soils were treated with phosphate rock, municipal solid waste, or biosolid compost. Phosphate amendments significantly enhanced plant As uptake from the two tested soils with frond As concentrations increasing up to 265% relative to the control. After 12 weeks, plants grown in phosphate-amended soil removed >8% of soil As. Replacement of As by P from the soil binding sites was responsible for the enhanced mobility of As and subsequent increased plant uptake. Compost additions facilitated As uptake from the CCA soil, but decreased As uptake from the ASC soil. Elevated As uptake in the compost-treated CCA soil was related to the increase of soil water-soluble As and As(V) transformation into As(III). Reduced As uptake in the ASC soil may be attributed to As adsorption to the compost. Chinese brake fern took up As mainly from the iron-bound fraction in the CCA soil and from the water-soluble/exchangeable As in the ASC soil. Without ferns for As adsorption, compost and phosphate amendments increased As leaching from the CCA soil, but had decreased leaching with ferns when compared to the control. For the ASC soil, treatments reduced As leaching regardless of fern presence. This study suggest that growing Chinese brake fern in conjunction with phosphate amendments increases the effectiveness of remediating As-contaminated soils, by increasing As uptake and decreasing As leaching.     

Comparison of batch, stirred flow chamber, and column experiments to study adsorption, desorption and transport of carbofuran within two acidic soils

Different methods (batch, column and stirred flow chamber experiments) used for adsorption and desorption of carbofuran studies were compared. All tested methods showed that the carbofuran adsorption was higher in the soil with the higher organic matter content, whereas the opposite behaviour was observed for the percentage of carbofuran desorbed. However, different methods have revealed some discrepancies in carbofuran adsorption/desorption kinetics. Although batch method showed interesting data on equilibrium experiments, such as a low heterogeneity for the carbofuran adsorption sites independent of soil organic matter content, it had some disadvantages for carbofuran adsorption/desorption kinetic studies. The disadvantages were related with the excessive limitations of this method on kinetics, i.e., no difference could be detected between different soils. However, with column and stirred flow chamber methods the carbofuran adsorption/desorption kinetics of different soils could be compared. Moreover, the absolute values of carbofuran adsorption/desorption and its rate were higher in the stirred flow chamber than in the batch and column experiments. Using stirred flow chamber experiments the carbofuran desorption was significantly faster than its adsorption, whereas carbofuran using column experiments they were similar. These discrepancies should be considered when the results obtained only with one method is discussed.     

Sorption and leaching of flucetosulfuron in soil

Abstract

The adsorption–desorption and leaching of flucetosulfuron, a sulfonylurea herbicide, was investigated in three Indian soils. Freundlich adsorption isotherm described the sorption mechanism of herbicide with adsorption coefficients (K_f) ranging from 17.13 to 27.99 and followed the order: Clayey loam?>?Loam?>?Sandy loam. The K_f showed positive correlation with organic carbon (OC) (r?=?0.910) and clay content (r?=?0.746); but, negative correlation with soil pH (r = ?0.635). The adsorption isotherms were S-type suggesting that herbicide adsorption was concentration dependent and increased with increase in concentration. Desorption followed the sequence: sandy loam?>?clayey loam?>?loam . Hysteresis (H) was observed in all the three soils with H?<?1. Leaching of flucetosulfuron correlated positively with the soil pH; but, negatively with the OC content. Sandy loam soil (OC- 0.40%, pH ?7.25) registered lowest adsorption and highest leaching of flucetosulfuron while lowest leaching was found in the loam soil (pH ? 7.89, OC ? 0.65%). The leaching losses of herbicide increased with increase in the rainfall intensity. This study suggested that the soil OC content, pH and clay content played important roles in deciding the adsorption–desorption and leaching behavior of flucetosulfuron in soils.     

Appendix

Abstract

The interaction of glyphosate [N‐(phosphonomethyl)‐glycine] with four typical European soils is reported. Results of adsorption and desorption isotherms show that the interaction of glyphosate with these soils was mainly related to content of iron and aluminium amorphus hydroxides. Moreover, it was found that the presence of divalent cations in 2: 1 clay minerals also contribute to glyphosate adsorption. The S‐type form of the adsorption isotherms revealed the existence of two different binding sites. These were exchangeable cations at low herbicide concentration and Fe and Al at higher glyphosate concentrations. The K maximum values of adsorption provided by the linear form of the Langmuir equation were found to be more consistent with soil parameters than those calculated by the Freundlich equation. The order of desorption from the soils was the reverse of that found for adsorption. Moreover, desorption varied from around 15 to 80% of the adsorbed herbicide according to the soil characteristics. This indicated that glyphosate adsorption on soils is far from being permanent and leaching to lower soil horizons with limited biological activity may occur.     

Effect of charcoal amendment on adsorption, leaching and degradation of isoproturon in soils

The effects of charcoal amendment on adsorption, leaching and degradation of the herbicide isoproturon in soils were studied under laboratory conditions. The adsorption data all fitted well with the Freundlich empirical equation. It was found that the adsorption of isoproturon in soils increased with the rate of charcoal amended (correlation coefficient r=0.957**, P<0.01). The amount of isoproturon in leachate decreased with the increase of the amount of charcoal addition to soil column, while the retention of isoproturon in soils increased with an increase in the charcoal content of soil samples. Biodegradation was still the most significant mechanism for isoproturon dissipation from soil. Charcoal amendment greatly reduced the biodegradation of isoproturon in soils. The half-lives of isoproturon degradation (DT(50)) in soils greatly extended when the rate of added charcoal increased from 0 to 50 g kg(-1) (for Paddy soil, DT(50) values increased from 54.6 to 71.4 days; for Alfisol, DT(50) from 16.0 to 136 days; and for Vertisol, DT(50) from 15.2 to 107 days). The degradation rate of isoproturon in soils was significantly negatively correlated with the amount of added charcoal. This research suggests that charcoal amendment may be an effective management practice for reducing pesticide leaching and enhancing its persistence in soils.     

Contribution of leaching of diazinon,parathion, tetrachlorvinphos and triazophos from glasshouse soils to their concentrations in water courses

Data on the adsorption and transformation rates of diazinon, parathion, tetrachlorvinphos and triazophos in soils were collected from a survey of the literature. As little information is available on their mobility, the adsorption of tetrachlorvinphos and triazophos on three soils was measured in a slurry experiment. Properties of diazinon were introduced into a computer model simulating glasshouse soil systems in a simplified way. The leaching of diazinon from the root zone was calculated to be zero. The properties of the other three organophosphates indicate that in similar computations leaching from the root zone would have been even lower.Samples from tile drains and water courses in areas with many glasshouses were analysed by gas-liquid chromatography. The concentration of the four organophosphate insecticides in almost all of the samples of water from tile drains was below the detectable limit. However in samples from the water courses, pesticide residues were found regularly, sometimes at fairly high concentrations. Thus contamination of water courses would seem to be produced not by leaching of pesticides through the soil but by other pathways.     

Evaluating non-equilibrium solute transport in small soil columns

Displacement studies on leaching of bromide and two pesticides (atrazine and isoproturon) were conducted under unsaturated steady state flow conditions in 24 small undisturbed soil columns (5.7 cm in diameter and 10 cm long) each collected from two sites differing in soil structure and organic carbon content in North Germany. There were large and irregular variabilities in the characteristics of both soils, as well as in the shapes of breakthrough curves (BTCs) of different columns, including some with early breakthrough and increased tailing, qualitatively indicating the presence of preferential flow. It was estimated that one preferential flow column (PFC) at site A, and four at site B, contributed, respectively to 11% and 58% of the accumulated leached fraction and to more than 80% of the maximum observed standard deviation (SD) in the field-scale concentration and mass flux of pesticides at two sites. The bromide BTCs of two sites were analyzed with the equilibrium convection-dispersion equation (CDE) and a non-equilibrium two-region/mobile-immobile model. Transport parameters of these models for individual BTCs were determined using a curve fitting program, CXTFIT, and by the time moment method. For the CDE based equilibrium model, the mean values of retardation factor, R, considered separately for all columns, PFCs or non-preferential flow columns (NPFCs) were comparable for the two methods; significant differences were observed in the values of dispersion coefficients of two sites using the two estimation methods. It was inferred from the estimated parameters of non-equilibrium model that 5-12% of water at site A, and 12% at site B, was immobile during displacement in NPFCs. The corresponding values for PFCs of two sites were much larger, ranging from 25% to 51% by CXTFIT and from 24% to 72% by the moment method, suggesting the role of certain mechanisms other than immobile water in higher degrees of non-equilibrium in these columns. Peclet numbers in PFCs of both sites were consistently smaller than five, indicating the inadequacy of the non-equilibrium model to incorporate the effect of all forms of non-equilibrium in PFCs. Overall, the BTCs of individual NPFCs, PFCs and of field average concentration at the two sites were better reproduced with parameters obtained from CXTFIT than by the moment method. The moment method failed to capture the peak concentrations in PFCs, but tended to describe the desorption and tail branches of BTCs better than the curve fitting approach.     

Impact of sewage sludge spreading on nickel mobility in a calcareous soil: adsorption–desorption through column experiments

A soil column adsorption–desorption study was performed on an agricultural calcareous soil to determine the impact of sewage sludge spreading on nickel mobility. Ni adsorption experiments were followed by desorption tests involving the following liquid extractants: water, calcium (100 mg/L), oxalic acid (525 mg/L equivalent to 100 mg carbon/L), and sludge extracts (0.5 and 2.5 g/L). Desorption tests were also conducted after sewage sludge spreading at three application rates (30, 75, and 150 t/ha). According to the breakthrough curve, Ni adsorption was irreversible and occurred mainly through interactions with calcite surface sites. Nickel desorption from the soil column was promoted in presence of significant dissolved organic carbon (DOC) concentration as observed with oxalic acid elution and sludge extract at 2.5 g/L. In sludge-amended soil columns, the maximum Ni levels occurred in first pore volumes, and they were positively correlated to the sludge application rate. The presence of DOC in leaching waters was the main factor controlling Ni desorption from the sludge-amended soil columns. This finding implies that DOC generated by sludge applied on calcareous soils might facilitate the leaching of Ni due to the formation of soluble Ni–organic complexes. Thus, sludge application can have potential environmental impacts in calcareous soils, since it promotes nickel transport by decreasing Ni retention by soil components.     

Evaluating equilibrium and non-equilibrium transport of bromide and isoproturon in disturbed and undisturbed soil columns

In this study, displacement experiments of isoproturon were conducted in disturbed and undisturbed columns of a silty clay loam soil under similar rainfall intensities. Solute transport occurred under saturated conditions in the undisturbed soil and under unsaturated conditions in the sieved soil because of a greater bulk density of the compacted undisturbed soil compared to the sieved soil. The objective of this work was to determine transport characteristics of isoproturon relative to bromide tracer. Triplicate column experiments were performed with sieved (structure partially destroyed to simulate conventional tillage) and undisturbed (structure preserved) soils. Bromide experimental breakthrough curves were analyzed using convective-dispersive and dual-permeability (DP) models (HYDRUS-1D). Isoproturon breakthrough curves (BTCs) were analyzed using the DP model that considered either chemical equilibrium or non-equilibrium transport. The DP model described the bromide elution curves of the sieved soil columns well, whereas it overestimated the tailing of the bromide BTCs of the undisturbed soil columns. A higher degree of physical non-equilibrium was found in the undisturbed soil, where 56% of total water was contained in the slow-flow matrix, compared to 26% in the sieved soil. Isoproturon BTCs were best described in both sieved and undisturbed soil columns using the DP model combined with the chemical non-equilibrium. Higher degradation rates were obtained in the transport experiments than in batch studies, for both soils. This was likely caused by hysteresis in sorption of isoproturon. However, it cannot be ruled out that higher degradation rates were due, at least in part, to the adopted first-order model. Results showed that for similar rainfall intensity, physical and chemical non-equilibrium were greater in the saturated undisturbed soil than in the unsaturated sieved soil. Results also suggested faster transport of isoproturon in the undisturbed soil due to higher preferential flow and lower fraction of equilibrium sorption sites.