Speciated Hydrocarbon Emissions from the Combustion of Single Component Fuels. I. Effect of Fuel Structure

Speciated hydrocarbon emissions data have been collected for six single-component fuels run in a laboratory pulse flame combustor (PFC). The six fuels include n-heptane, isooctane (2, 2, 4-trimethylpentane), cyclohexane, 1-hexene, toluene, and methyl-t-butyl ether (MTBE: an oxygenated fuel extender). Combustion of non-aromatic fuels in the PFC (at a fuel/air equivalence ratio of Φ = 1.02) produced low levels of unburned fuel and high yields of methane and olefins (> 75 percent combined) irrespective of the molecular structure of the fuel. In contrast, hydrocarbon emissions from toluene combustion in the PFC were comprised predominantly of unburned fuel (72 percent). With the PFC, low levels of 1, 3-butadiene (0.3-1.8 percent) were observed from all the fuels except MTBE, for which no measurable level (<0.2 percent) was detected; low levels of benzene were observed from isooctane, heptane, and 1-hexene, but significant levels (9 percent) from cyclohexane and toluene. No measurable amount of benzene (< 0.2 percent) was observed in the MTBE exhaust.

For isooctane and toluene the speciated hydrocarbon emissions from a spark-ignited (SI) single-cylinder engine were also determined. HC emissions from the SI engine contained the same species as observed from the PFC, although the relative composition was different. For the non-aromatic fuel isooctane, unburned fuel represented a larger fraction (50 percent) of the HC emissions when run in the engine. HC emissions from toluene combustion in the engine were similar to those from the PFC.     

Evaluation of combustion by-products of MTBE as a component of reformulated gasoline

Methyl tertiary-butyl ether (MTBE) is a gasoline oxygenate that is widely used throughout the US and Europe as an octane-booster and as a means of reducing automotive carbon monoxide (CO) emissions. The combustion by-products of pure MTBE have been evaluated in previous laboratory studies, but little attention has been paid to the combustion by-products of MTBE as a component of gasoline. MTBE is often used in reformulated gasoline (RFG), which has chemical and physical characteristics distinct from conventional gasoline. The formation of MTBE by-products in RFG is not well-understood, especially under "worst-case" vehicle emission scenarios such as fuel-rich operations, cold-starts or malfunctioning emission control systems, conditions which have not been studied extensively. Engine-out automotive dynamometer studies have compared RFG with MTBE to non-oxygenated RFG. Their findings suggest that adding MTBE to reformulated gasoline does not impact the high temperature flame chemistry in cylinder combustion processes. Comparison of tailpipe and exhaust emission studies indicate that reactions in the catalytic converter are quite effective in destroying most hydrocarbon MTBE by-product species. Since important reaction by-products are formed in the post-flame region, understanding changes in this region will contribute to the understanding of fuel-related changes in emissions.     

Partitioning of aromatic and oxygenated constituents into water from regular and ethanol-blended gasolines

Variability in gasoline-water partitioning of major aromatic constituents (benzene, toluene, ethylbenzene, and xylenes (BTEX)) and methyl tert-butyl ether (MTBE) were examined for regular and ethanol-blended gasolines. By use of a two-phase liquid-liquid equilibrium model, the distribution of nonpolar solutes between fuel phase and water was related to principles of equilibrium. The models derived using Raoult's law convention for activity coefficients and liquid solubility is presented. The observed inverse log-log linear dependence of K_fw values on aqueous solubility, could be well predicted by assuming gasoline to be an ideal solvent mixture. Oxygenated additives (i.e., ethanol and MTBE), in the low percent range (below 5%), were shown to have minimal or negligible cosolvent effects on hydrocarbon partitioning. In the case of high fuel-to-water ratio (e.g., 1:1) or near contaminant source zone, the cosolvent effect of oxygenated gasoline with high content of ethanol (e.g., E85) will be environmentally significant.     

Speciated Hydrocarbon Emissions from the Combustion of Single Component Fuels. II. Catalyst Effects

Six single-component fuels (isooctane, n-heptane, 1-hexene, cyclohexane, methyl-t-butyl ether (MTBE), and toluene) and a multicomponent tracer fuel were burned in a pulse flame combustor (PFC) and reacted over a three-way automotive catalyst. The composition of the raw, uncatalyzed PFC exhaust was characterized in Part I of this study. In Part II, we focus on the conversions of the individual exhaust HC species over the catalyst. In accord with previous studies, the order of reactivity observed for the various classes of HC species was: methane (least reactive) < saturated HC < aromatics < unsaturated HC (most reactive). These differences in catalytic reactivity led to increases in the relative concentrations of methane and some saturated hydrocarbons in the post catalyst exhaust, and corresponding decreases in the relative concentrations of aromatic and unsaturated hydrocarbons. Oxygenated organic compounds showed wide variability in catalytic reactivity depending on the specific compounds involved. Catalytic conversion of the air toxic, 1,3-butadiene, was essentially complete to within detection limits. Benzene and toluene appeared to have similar intrinsic catalytic reactivities. However, net conversion of benzene in most instances was significantly less than that of toluene owing to demethylation of toluene (to form benzene) occurring in parallel with benzene oxidation. Rich combustion of both isooctane and tracer fuel led to the production of methane by the catalyst, primarily from reactions of acetylene and small olefins.     

Speciated hydrocarbon and carbon monoxide emissions from an internal combustion engine operating on methyl tertiary butyl ether-containing fuels

In the present work, engine and tailpipe (after a three-way catalytic converter) emissions from an internal combustion engine operating on two oxygenated blend fuels [containing 2 and 11% weight/weight (w/w) methyl tertiary butyl ether (MTBE)] and on a nonoxygenated base fuel were characterized. The engine (OPEL 1.6 L) was operated under various conditions, in the range of 0-20 HP. Total unburned hydrocarbons, carbon monoxide, methane, hexane, ethylene, acetaldehyde, acetone, 2-propanol, benzene, toluene, 1,3-butadiene, acetic acid, and MTBE were measured at each engine operating condition. As concerns the total HC emissions, the use of MTBE was beneficial from 1.90 to 3.81 HP, which were by far the most polluting conditions. Moreover, CO emissions in tailpipe exhaust were decreased in the whole operation range with increasing MTBE in the fuel. The greatest advantage of MTBE addition to gasoline was the decrease in ethylene, acetaldehyde, benzene, toluene, and acetic acid emissions in engine exhaust, especially when MTBE content in the fuel was increased to 11% w/w. In tailpipe exhaust, the catalyst operation diminished the observed differences. Ethylene, methane, and acetaldehyde were the main compounds present in exhaust gases. Ethylene was easily oxidized over the catalyst, while acetaldehyde and methane were quite resistant to oxidation.     

Speciated Hydrocarbon and Carbon Monoxide Emissions from an Internal Combustion Engine Operating on Methyl Tertiary Butyl Ether-Containing Fuels

ABSTRACT

In the present work, engine and tailpipe (after a three-way catalytic converter) emissions from an internal combustion engine operating on two oxygenated blend fuels [containing 2 and 11% weight/weight (w/w) methyl tertiary butyl ether (MTBE)] and on a nonoxygenated base fuel were characterized. The engine (OPEL 1.6 L) was operated under various conditions, in the range of 0-20 HP. Total unburned hydrocarbons, carbon monoxide, methane, hexane, ethylene, acetaldehyde, acetone, 2-propanol, benzene, toluene, 1,3-butadiene, acetic acid, and MTBE were measured at each engine operating condition. As concerns the total HC emissions, the use of MTBE was beneficial from 1.90 to 3.81 HP, which were by far the most polluting conditions. Moreover, CO emissions in tailpipe exhaust were decreased in the whole operation range with increasing MTBE in the fuel.

The greatest advantage of MTBE addition to gasoline was the decrease in ethylene, acetaldehyde, benzene, toluene, and acetic acid emissions in engine exhaust, especially when MTBE content in the fuel was increased to 11% w/w. In tailpipe exhaust, the catalyst operation diminished the observed differences. Ethylene, methane,and acetaldehyde were the main compounds present in exhaust gases. Ethylene was easily oxidized over the catalyst,while acetaldehyde and methane were quite resistant to oxidation.     

Exposure to methyl tertiary butyl ether and benzene in close proximity to service stations

Exposure estimates based solely on proximity to air pollution sources are not sound and require confirmation. Accordingly, since a very limited amount of actual data for this type of exposure estimate is currently available, this study was conducted to provide actual data on residents' exposure to two important gasoline constituents [methyl tertiary butyl ether (MTBE) and benzene] relative to their proximity to roadside service stations. The results confirmed that residents in neighborhoods near service stations are exposed to elevated ambient MTBE and benzene levels compared with those living farther from such a source. However, it was also found that the presumed elevated outdoor benzene levels (a mean of 1.7 ppb) even in close proximity to service stations did not exceed the indoor levels (a mean of 2.2 ppb) of exposure for those living nearby. Regardless of residents' distance from service stations, an indoor source (cigarette smoking) appeared to be the major contributor to their benzene exposure. Conversely, for MTBE, roadside service stations were found to be the major contributor to residents' exposure. In addition, the residents close to the stations were exposed to elevated indoor and outdoor MTBE levels. The sampling period (daytime and nighttime) and season (winter and summer) were additional parameters for the outdoor MTBE and benzene levels and the indoor MTBE levels. Meanwhile, the breathing zone air concentrations of service station attendants for both MTBE and benzene were significantly higher than those of drivers (p < 0.05). In addition, the breathing zone concentrations were significantly higher during summer than during winter for both drivers and attendants (p < 0.05).     

Germany

ABSTRACT

The 1988 Alternative Motor Fuels Act and the 1990 Clean Air Act Amendments require examination of the potential to favorably influence air quality by changing the composition of motor vehicle fuels. Motor vehicle tailpipe and evaporative emissions were characterized using laboratory simulations of roadway driving conditions and a variety of vehicle-fuel technologies (reformulated gasoline (RFG), methanol (M85), ethanol (E85), and natural gas (CNG)). Speciated organic compound (with Carter MIR ozone potential), CO, and NO_x emission rates and fuel economy were characterized. The Carter MIR ozone potential of combined Federal Test Procedure (FTP) tailpipe and evaporative emissions was reduced more than 90% with CNG relative to RFG, M85, and E85 fuels. FTP toxic compound emissions (benzene, formaldehyde, acetalde-hyde, and 1,3-butadiene) were greater with M85 and E85 fuels than with RFG fuel, and less with CNG fuel than RFG fuel. The most abundant toxic compound was benzene with RFG fuel, formaldehyde with M85 fuel, and acetaldehyde with E85 fuel. FTP MPG fuel economies were reduced with M85 and E85 fuels relative to RFG fuel, consistent with their lower BTU/gal. Energy efficiencies (BTU/mi) were improved with all the alternative fuels relative to RFG. Carter MIR ozone potential was generally reduced with the alternative fuels relative to RFG fuel under REP05 (high speeds and acceleration rates) driving conditions (most significantly with CNG). Toxic aldehyde emissions were reduced under REP05 conditions relative to FTP conditions with all the tested fuels, and toxic benzene emissions were elevated under high acceleration conditions.     

The effect of reformulated gasoline on ambient carbon monoxide concentrations in southeastern Wisconsin

Reformulated gasoline (RFG) contains oxygen additives such as methyl tertiary butyl ether or ethanol. The additives enable vehicles to burn fuel with a higher air/fuel ratio, thereby lowering the emission of carbon monoxide (CO) and volatile organic compounds (VOCs). Because VOCs react with sunlight to form ozone (O3), the Clean Air Act requires severe O3 nonattainment areas such as southeastern Wisconsin to use RFG. On July 17, 2001, the U.S. Environmental Protection Agency (EPA) granted Milwaukee, WI, and Chicago, IL, a waiver from the VOC reduction requirement of Phase II RFG. The VOC reduction requirement was lowered from 27.4% of the 1990 baseline fuel to 25.4%. The assumption was that ethanol-blended RFG would lower summertime CO concentrations sufficiently to offset the increased VOC emissions. The waiver is estimated to increase VOC emissions by approximately 0.8%, or 0.4 t of VOC on a hot summer weekday. This study evaluates whether RFG has been effective in lowering southeastern Wisconsin ambient CO concentrations. Three years of ambient CO data before RFG was introduced were compared with the first three years of ambient CO data after RFG was introduced. This paper also evaluates how the meteorology, vehicle inspection/maintenance program, vehicle miles traveled, and stationary source emissions influence CO concentrations. The winter decrease in ambient CO concentrations was found to be statistically significant, while the summer data showed no statistically significant change, indicating that RFG is most effective lowering ambient CO concentrations in cold weather.     

U. S. EPA Views as “Unwarranted” Federal Regulatory Involvement in Odor Control

ABSTRACT

Although there have been several studies examining emissions of criteria pollutants from in-use alternative fuel vehicles (AFVs), little is known about emissions of hazardous air pollutants (HAPs) from these vehicles. This paper explores HAP tailpipe emissions from a variety of AFVs operating in the federal government fleet and compares these emissions to emissions from identical vehicles operating on reformulated gasoline. Emissions estimates are presented for a variety of fuel/model combinations and on four HAPs (acetaldehyde, 1,3-butadi-ene, benzene, and formaldehyde). The results indicate that all AFVs tested offer reduced emissions of HAPs, with the following exceptions: ethanol fueled vehicles emit more acetaldehyde than RFG vehicles, and ethanol- and methanol-fueled vehicles emit more formaldehyde than RFG vehicles. The results from this paper can lead to more accurate emissions factors for HAPs, thus improving HAP inventory and associated risk estimates for both AFVs and conventional vehicles.     

The Impact of California Phase 2 Reformulated Gasoline on Real-World Vehicle Emissions

ABSTRACT

In mid-1996, California implemented Phase 2 Reformulated Gasoline (RFG). The new fuel was designed to further decrease emissions of hydrocarbons (HC_s), oxides of nitrogen (NO_x), carbon monoxide (CO), sulfur dioxide (SO₂), and other toxic species. In addition, it was formulated to reduce the ozone-forming potential of the HCs emitted by vehicles. Previous studies have observed that emissions from on-road vehicles can differ significantly from those predicted by mobile source emissions models, and so it is important to quantify the change in emissions in a real-world setting. In October 1995, prior to the introduction of California Phase 2 RFG, the Desert Research Institute (DRI) performed a study of vehicle emissions in Los Angeles' Sepulveda Tunnel. This study provided a baseline against which the results of a second experiment, conducted in July 1996, could be compared to evaluate the impact of California Phase 2 RFG on emissions from real-world vehicles. Compared with the 1995 experiment, CO and NO_x emissions exhibited statistically significant decreases, while the decrease in non-methane hydrocarbon emissions was not statistically significant.

Changes in the speciated HC emissions were evaluated. The benzene emission rate decreased by 27% and the overall emission rate of aromatic compounds decreased by 22% comparing the runs with similar speeds. Emissions of alkenes were virtually unchanged; however, emissions of combustion related unsaturates (e.g., acetylene, ethene) increased, while heavier alkenes decreased. The emission rate of methyl tertiary butyl ether (MTBE) exhibited a larger increase. Overall changes in the ozone-forming potential of the emissions were not significantly different, with the increased contributions to reactivity from paraffins, ole-fins, and MTBE being offset by a large decrease in reactivity due to aromatics.     

The Effect of Reformulated Gasoline on Ambient Carbon Monoxide Concentrations in Southeastern Wisconsin

Abstract

Reformulated gasoline (RFG) contains oxygen additives such as methyl tertiary butyl ether or ethanol. The additives enable vehicles to burn fuel with a higher air/fuel ratio, thereby lowering the emission of carbon monoxide (CO) and volatile organic compounds (VOCs). Because VOCs react with sunlight to form ozone (O₃), the Clean Air Act requires severe O₃ nonattainment areas such as southeastern Wisconsin to use RFG. On July 17, 2001, the U.S. Environmental Protection Agency (EPA) granted Milwaukee, WI, and Chicago, IL, a waiver from the VOC reduction requirement of Phase II RFG. The VOC reduction requirement was lowered from 27.4% of the 1990 baseline fuel to 25.4%. The assumption was that ethanol-blended RFG would lower summertime CO concentrations sufficiently to offset the increased VOC emissions. The waiver is estimated to increase VOC emissions by ～0.8%, or 0.4 t of VOC on a hot summer weekday. This study evaluates whether RFG has been effective in lowering southeastern Wisconsin ambient CO concentrations. Three years of ambient CO data before RFG was introduced were compared with the first three years of ambient CO data after RFG was introduced. This paper also evaluates how the meteorology, vehicle inspection/maintenance program, vehicle miles traveled, and stationary source emissions influence CO concentrations. The winter decrease in ambient CO concentrations was found to be statistically significant, while the summer data showed no statistically significant change, indicating that RFG is most effective lowering ambient CO concentrations in cold weather.     

Treatment of groundwater contaminated with gasoline components by an ozone/UV process

In this paper, the treatment of real groundwater samples contaminated with gasoline components, such as benzene, toluene, ethylbenzene, and xylene (BTEX), methyl tert-butyl ether (MTBE), tert-butyl alcohol (TBA), and other gasoline constituents in terms of total petroleum hydrocarbons as gasoline (TPHg) by an ozone/UV process was investigated. The treatment was conducted in a semi-batch reactor under different experimental conditions by varying ozone gas dosage and incident UV light intensity. The groundwater samples contained BTEX compounds, MTBE, TBA, and TPHg in the ranges of 5-10000, 3000-5500, 80-1400, and 2400-20000mugl(-1), respectively. The ozone/UV process was very effective compared to ozonation in the removal of the gasoline components from the groundwater samples. For the various gasoline constituents, more than 99% removal efficiency was achieved for the ozone/UV process and the removal efficiency for ozonation was as low as 27%. The net ozone consumed per mol of organic carbon (from BTEX, MTBE, and TBA) oxidized varied in the range of 5-60 for different types of groundwater samples treated by the ozone/UV process. In ozonation experiments, it was observed that the presence of sufficient amount of iron in groundwater samples improved the removal of BTEX, MTBE, TBA, and TPHg.     

Effect of gasoline formulation on the formation of photosmog: a box model study

Based on exhaust gas analyses from the combustion of five different types of gasoline in a passenger car operated on a chassis dynamometer, box model simulations of the irradiation of exhaust/NOx/air mixtures using an established chemical mechanism for a standardized photosmog scenario were performed. The fuel matrix used covered wide fractional ranges for paraffinic, olefinic, and aromatic hydrocarbons. Two fuels also contained methyl tertiary butyl ether (MTBE). The different O3 profiles calculated for each run were compared and interpreted. The O3 levels obtained were strongly influenced by the exhaust gas concentrations of aromatic and olefinic hydrocarbons. The higher exhaust content of these compounds caused higher O3 production in the smog system investigated. The conclusion of the present study is that the composition of gasoline cannot be taken directly for the estimation of the emissions' O3 creation potential from its combustion. Variation of the dilution in the different calculations showed evidence for an additional influence of transport effects. Accordingly, further detailed exhaust gas analyses followed by more complex modeling studies are necessary for a proper characterization of the relationship between fuel blend and gasoline combustion products.     

Effect of methyl tertiary butyl ether concentrations on exhaust emissions from gasoline used in the metropolitan area of Mexico City

In this work, the primary objective was to assess the impact of oxygenated fuel on the exhaust emissions from an important fraction of vehicles in the Metropolitan Area of Mexico City (MAMC). The results aim to provide information on the actual effect of MTBE on a fleet that represents more than 60% of the in-use vehicles in the MAMC. Ten vehicles were tested with a low-octane base gasoline, and 10 more with a regular-grade unleaded base gasoline. Three MTBE concentrations, 5, 10, and 15 vol %, were tested following the U.S. Federal Test Procedure (FTP). CO, total HC, and NOx from the exhaust gases were quantitatively evaluated and also characterized for FTP speciated organic emissions. From this data, the O3-forming potential of the fuels was calculated. Results show that for the fleet using low-octane gasoline, the addition of 10% MTBE substantially reduced CO emissions, but total HC concentration in the exhaust showed a modest decrease. For the regular gasoline, the 10% MTBE blend seemed to be the best choice, but there was not a significant decrease in emissions. The specific reactivity of each fuel, expressed in grams of O3 per gram of nonmethane organic gases, increased with MTBE concentration in both cases. This result is important to consider, especially for a region like Mexico City, which has high atmospheric O3 concentrations.     

Measurements of peroxyacyl nitrates (PANS) in Mexico City: implications for megacity air quality impacts on regional scales

Peroxyacyl nitrates (PANs) were measured using gas chromatography with electron capture detection (GC/ECD) in north central Mexico City during February–March of 1997. Peroxyacetyl nitrate (PAN) was observed to exceed 30 ppb during five days of the study, with peroxypropionyl nitrate (PPN) and peroxybutryl nitrate (PBN) reaching 6 and 1 ppb maximum, respectively. Levels of total PANs typically exceeded 10 ppb during the period of measurement and showed a very strong diurnal variation with PANs maximum during the early afternoon and falling to less than 0.1 ppb during the evening hours. These levels of PANs are the highest reported values in North America (and the world) for an urban center, since levels of approximately 30 ppb were reported during the late 1970s in the Los Angeles area (South Coast Air Basin, Tuazon et al., 1978). Hydrocarbon measurements indicate that the levels of olefins, specifically butenes are significant in Mexico City. A time series taken of source indicator hydrocarbons taken before and during a Mexican National Holiday with reduced automobile traffic clearly show that mobile sources of butenes are as important as liquefied petroleum gas. Observations of 10–40 ppb C methyl-t-butyl ether (MTBE) are consistent with MTBE/gasoline fuel usage as a source of isobutene and formaldehyde. Both these reactive species can lead to increased oxidant and PAN formation. The strong diurnal profiles of PANs are consistent with regional clearing of the Mexico City air basin on a daily basis. Estimates are given using a simple box model calculation for a number of key primary and secondary pollutant emissions from this megacity on an annual basis. These calculations indicate that megacities can be important sources of both primary and secondary pollutants, and that PANs produced in megacity environments are likely to contribute strongly to regional scale ozone and aerosol productions during long range transport.     

Applications of Anthropogenic Lead ArchaeoStratigraphy (ALAS Model) to Hydrocarbon Remediation

A model, which employs the use of high precision stable lead isotopic analyses, has been developed to estimate the age of hydrocarbon releases. The ALAS Model (Anthropogenic Lead ArchaeoStratigraphy) is based on calibrated, systematic increases in lead isotope ratios of gasolines caused by shifts in sources of lead ores used by the U.S. lead industry, including manufacturers of alkylleads, to more radiogenic Mississippi Valley Type (MVT) deposits. Acquisition of high quality samples (free product, gasoline-impacted soil and groundwater) of known age and subsequent analyses of the hydrocarbon component by high precision lead isotopic analyses by thermal ionization mass spectrometry (TIMS) have produced the ALAS Model calibration curve. Age uncertainties range from - 1 to 2 years for gasoline releases which occurred between 1965 and 1990, the major era of leaded gasoline usage. Analytical methods required to measure lead isotope ratios on ~5 nanograms of lead with precisions and accuracy of < - 0.1% (2 SEM ) are discussed in detail. Published lead isotopic measurements of gasoline-derived anthropogenic lead of samples throughout the United States are used to demonstrate the wide geographic range over which the ALAS Model may be applied. Two representative case studies involving an early 1970s free product release in California and the discrimination of a 1970s from modern unleaded gasoline release in Florida demonstrate the use of the model on single and multiple hydrocarbon releases, respectively, in different geographic regions of the United States. A third investigation focuses on the use of lead isotopes to correlate dissolved phase hydrocarbons with their source, in this case, unleaded (aka low lead) gasoline releases in New Jersey. Dissolved phase hydrocarbons (BTEX/MTBE) are shown to carry the lead isotopic signature of the unleaded gasoline into groundwater, allowing the specific source of the release to be identified. Investigations of lead isotopes as tracers of MTBE in groundwater are ongoing. However, both laboratory and field data indicate MTBE carries the lead isotopic signature of its unleaded gasoline source into groundwater, demonstrating the potential of the lead isotopic system as a discriminant of MTBE sources. Although developed to estimate the age of leaded gasoline releases, the ALAS Model has been successfully applied in studies requiring age dating of jet-A, diesel, kerosene, motor oil, and heating oil. These petroleum distillates are suspected of accidentally acquiring small, yet significant quantities of alkylleads during refining, allowing accurate ALAS Model ages to be determined. When lead levels in these petroleum distillates are within their normal range, typically tens to hundreds of ppb lead, it is possible to use lead isotopic ratios to correlate environmental releases of these products to their source or other releases.     

Effect of Gasoline Formulation on the Formation of Photosmog: A Box Model Study

Abstract

Based on exhaust gas analyses from the combustion of five different types of gasoline in a passenger car operated on a chassis dynamometer, box model simulations of the irradiation of exhaust/NO_x /air mixtures using an established chemical mechanism for a standardized photo-smog scenario were performed. The fuel matrix used covered wide fractional ranges for paraffinic, olefinic, and aromatic hydrocarbons. Two fuels also contained methyl tertiary butyl ether (MTBE). The different O₃ profiles calculated for each run were compared and interpreted. The O₃ levels obtained were strongly influenced by the exhaust gas concentrations of aromatic and olefinic hydro-carbons. The higher exhaust content of these compounds caused higher O₃ production in the smog system investigated. The conclusion of the present study is that the composition of gasoline cannot be taken directly for the estimation of the emissions’ O₃ creation potential from its combustion. Variation of the dilution in the different calculations showed evidence for an additional influence of transport effects. Accordingly, further detailed exhaust gas analyses followed by more complex modeling studies are necessary for a proper characterization of the relationship between fuel blend and gasoline combustion products.     

Effect of Methanol on Exhaust Composition of a Fuel Containing Toluene,n-Heptane,and Isooctane

This study describes the variations in the chemical composition of the exhaust from a single cylinder engine when up to 25% methanol is added to a fuel blend of toluene, isooctane, and n-heptane. Under fuel-rich conditions, and with increasing methanol concentration, it is observed that unburned fuel and benzene emissions increase, exhaust acetylene remains constant, and propylene, isobutylene, methane, ethylbenzene, and styrene concentrations decrease. As oxygen becomes more available, the effects of methanol are reduced, and at an equivalence ratio of 1.25—excess oxygen now is present—methanol no longer affects the concentration of exhaust hydrocarbons. These observations are explained by the reactions of formaldehyde—an incomplete combustion product of methanol— with alkyl radicals derived from the fuel. The photochemical reactivity of the exhaust is unchanged when up to 15% of methanol is present in the fuel at an equivalence ratio of 0.85, but increases at higher methanol contents because of the increase in unburned toluene in the exhaust.     

Seasonal impact of blending oxygenated organics with gasoline on motor vehicle tailpipe and evaporative emissions.

Emissions from a 1988 GM Corsica with adaptive learning closed loop control were measured with 4 fuels at 40, 75, and 90 degrees F. Evaporative and exhaust emissions were examined from each fuel at each test temperature. Test fuels were unleaded summer grade gasoline; a blend of this gasoline containing 8.1 percent ethanol; a refiner's blend stock; and the blend stock containing 16.2 percent methyl tertiary butyl ether. The ethanol and MTBE blends contained 3.0 percent oxygen by weight. Regulated emissions (total hydrocarbons, carbon monoxide, and oxides of nitrogen), detailed aldehydes, detailed hydrocarbons, ethanol, MTBE, benzene, and 1,3-butadiene were determined. The highest levels of regulated emissions were produced at the lower temperature. Blended fuels produced almost twice the evaporative hydrocarbon emissions at high temperatures as did the base fuels. Benzene emissions varied with fuels and operating temperatures, while 1,3-butadiene emissions decreased slightly with increasing temperatures. Formaldehyde emissions were not sensitive to fuel or temperature changes. Ethanol fuel blend total aldehyde emissions increased by 40 percent due to increased acetaldehyde emissions. Fuel blends had approximately a 3 percent economy decrease. The MTBE fuel blend appeared to offer the most reduction in total hydrocarbon, carbon monoxide, and oxides of nitrogen for the fuels and temperatures tested.