Rice husk ash as an effective adsorbent: evaluation of adsorptive characteristics for Indigo Carmine dye

Present study explored the adsorptive characteristics of Indigo Carmine (IC) dye from aqueous solution onto rice husk ash (RHA). Batch experiments were carried out to determine the influence of parameters like initial pH (pH(0)), contact time (t), adsorbent dose (m) and initial concentration (C(0)) on the removal of IC. The optimum conditions were found to be: pH(0)=5.4, t=8h and m=10.0 g/l. The pseudo-second-order kinetic model represented the adsorption kinetics of IC on to RHA. Equilibrium isotherms were analyzed by Freundlich, Langmuir, Temkin and Redlich-Peterson models using a non-linear regression technique. Adsorption of IC on RHA was favorably influenced by an increase in the temperature of the operation. The positive values of the change in entropy (DeltaS(0)) and heat of adsorption (DeltaH(0)); and the negative value of change in Gibbs free energy (DeltaG(0)) indicate feasible and spontaneous adsorption of IC on to RHA.     

Removal of direct red 12B and methylene blue from water by adsorption onto Fe (III)/Cr (III) hydroxide, an industrial solid waste

Removal of direct red 12B and methylene blue by adsorption onto Fe (III)/Cr (III) hydroxide was studied using various parameters such as agitation time, dye concentration, adsorbent dose and pH. Equilibrium adsorption data followed both Langmuir and Freundlich isotherms. Adsorption followed second-order rate kinetics. The Langmuir adsorption capacity (Qo) was found to be 5.0 and 22.8 mg dye per g of the adsorbent for direct red 12B and methylene blue, respectively. Acidic pH was favorable for the adsorption of direct red 12B and basic pH for methylene blue. Desorption studies showed that chemisorption seems to be the major mode of adsorption.     

Removal of copper (II) from aqueous solution by adsorption onto low-cost adsorbents

The use of low-cost adsorbents was investigated as a replacement for current costly methods of removing metals from aqueous solution. Removal of copper (II) from aqueous solution by different adsorbents such as shells of lentil (LS), wheat (WS), and rice (RS) was investigated. The equilibrium adsorption level was determined as a function of the solution pH, temperature, contact time, initial adsorbate concentration and adsorbent doses. Adsorption isotherms of Cu (II) on adsorbents were determined and correlated with common isotherm equations such as Langmuir and Freundlich models. The maximum adsorption capacities for Cu (II) on LS, WS and RS adsorbents at 293, 313 and 333 K temperature were found to be 8.977, 9.510, and 9.588; 7.391, 16.077, and 17.422; 1.854, 2.314, and 2.954 mg g(-1), respectively. The thermodynamic parameters such as free energy (delta G0), enthalpy (delta H0) and entropy changes (delta S0) for the adsorption of Cu (II) were computed to predict the nature of adsorption process. The kinetics and the factors controlling the adsorption process were also studied. Locally available adsorbents were found to be low-cost and promising for the removal of Cu (II) from aqueous solution.     

Kinetic and equilibrium characterization of uranium(VI) adsorption onto carboxylate-functionalized poly(hydroxyethylmethacrylate)-grafted lignocellulosics

This study investigated the feasibility of using a new adsorbent prepared from coconut coir pith, CP (a coir industry-based lignocellulosic residue), for the removal of uranium [U(VI)] from aqueous solutions. The adsorbent (PGCP-COOH) having a carboxylate functional group at the chain end was synthesized by grafting poly(hydroxyethylmethacrylate) onto CP using potassium peroxydisulphate-sodium thiosulphite as a redox initiator and in the presence of N,N'-methylenebisacrylamide as a crosslinking agent. IR spectroscopy results confirm the graft copolymer formation and carboxylate functionalization. XRD studies confirm the decrease of crystallinity in PGCP-COOH compared to CP, and it favors the protrusion of the functional group into the aqueous medium. The thermal stability of the samples was studied using thermogravimetry (TG). Surface charge density of the samples as a function of pH was determined using potentiometric titration. The ability of PGCP-COOH to remove U(VI) from aqueous solutions was assessed using a batch adsorption technique. The maximum adsorption capacity was observed at the pH range 4.0-6.0. Maximum removal of 99.2% was observed for an initial concentration of 25mg/L at pH 6.0 and an adsorbent dose of 2g/L. Equilibrium was achieved in approximately 3h. The experimental kinetic data were analyzed using a first-order kinetic model. The temperature dependence indicates an endothermic process. U(VI) adsorption was found to decrease with an increase in ionic strength due to the formation of outer-sphere surface complexes on PGCP-COOH. Equilibrium data were best modeled by the Langmuir isotherm. The thermodynamic parameters such as DeltaG(0), DeltaH(0) and DeltaS(0) were derived to predict the nature of adsorption. Adsorption experiments were also conducted using a commercial cation exchanger, Ceralite IRC-50, with carboxylate functionality for comparison. Utility of the adsorbent was tested by removing U(VI) from simulated nuclear industry wastewater. Adsorbed U(VI) ions were desorbed effectively (about 96.2+/-3.3%) by 0.1M HCl. The adsorbent was suitable for repeated use (more than four cycles) without any noticeable loss of capacity.     

Removal of chromium(VI) from electroplating industry wastewater using bagasse fly ash—a sugar industry waste material

A waste product generated in the sugar industry in India has been converted into a cheap potential adsorbent. This has been characterised and utilized for the removal of chromium (VI) from synthetic and actual wastewater. The sorption efficiency decreases with increase in pH. Adsorption of Cr (VI) on bagasse fly ash follows the Freundlich and Langmuir isotherms and these have been used to obtain the thermodynamic parameters of the process. The sorption capacity of this adsorbent for chromium removal is found to be comparable to other low cost adsorbents.     

Exploitation of Trichoderma harzianum mycelial waste for the removal of rhodamine 6G from aqueous solution

The harvested mycelial waste of Trichoderma harzianum was used as an adsorbent for the removal of rhodamine 6G and was studied in batch mode. The effects of agitation time and initial dye concentration, adsorbent dosage and pH were examined. The study revealed that the amount of dye adsorbed (mgg(-1)) increased with increase in agitation time and reached equilibrium after 120 min, for dye concentrations of 10-50 mg L(-1). The adsorbent dosage of 1.0 g/50 mL and pH of 8.0 were found to be optimum for maximum dye removal. The batch mode adsorption data followed both the Langmuir and Freundlich isotherms. The pseudo first- and second-order rate kinetics were applied to the adsorbent system. The adsorption kinetics of rhodamine 6G showed that the pseudo-second-order kinetic model provided the best correlation of the equilibrium data. The study implies that it is possible to develop a dye removal system by using T. harzianum biomass, which occurs as sludge in waste stream of fermentation industries.     

Development of activated carbon from Nerium oleander flower and their rapid adsorption of direct and reactive dyes

The present study investigates the thermally activated carbon derived from Nerium oleander flower which was used an adsorbent. Physicochemical properties of Nerium oleander flower carbon (NOFC) were characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform infrared for the removal of DTB (Direct Turquoise Blue) and RR-HE7B (Reactive red–HE7B) dyes from aqueous solution. Adsorption studies were carried out with different pH, adsorbent dose, contact time, and initial concentration dye solution. Optimum conditions for maximum removal of DTB and RR-HE7B was achieved to be pH 2 for both dyes, adsorbent dose of 100 mg and equilibrium time of 35 and 60 min, respectively, for NOFC. The maximum adsorption capacity of NOFC was found to be 33.33 and 19.60 mg g^?1, respectively, for the removal of dye solution. The mechanism of adsorption was studied by using different kinetic models and isotherms. The results clearly showed that the NOFC adsorption was fitted to pseudo–first-order for DTB and pseudo–second-order for RR-HE7B. Equilibrium data were well fitted with both isotherm models. According to the results, NOFC can effectively remove DTB and RR-HE7B from aqueous solutions.     

Utilization of powdered waste sludge (PWS) for removal of textile dyestuffs from wastewater by adsorption

Acid pre-treated powdered waste sludge (PWS) was used for removal of textile dyestuffs from aqueous medium by adsorption as an alternative to the use of powdered activated carbon (PAC). The rate and extent of dysetuff removals were determined for four different dyestuffs at different PWS concentrations varying between 1 and 6 gl(-1). Biosorbed dyestuff concentrations at equilibrium decreased with increasing PWS concentration for all dyestuffs tested. PWS was more effective for adsorption of Remazol red RR and Chrisofonia direct yellow 12 as compared to the other dyestuffs tested. More than 80% percent dyestuff removal was obtained for all dyestuffs at PWS concentrations above 4 gl(-1) after 6h of incubation. Similar to percent dyestuff removal, the rate of adsorption was maximum at a PWS concentration of 4 gl(-1). Kinetics of adsorption of dyestuffs was investigated by using the first- and second-order kinetic models and the kinetic constants were determined. Second-order kinetics was found to fit the experimental data better than the first-order model for all dyestuffs tested. Adsorption isotherms were established for all dyestuffs used and the isotherm constants were determined by using the experimental data. Langmuir and the generalized adsorption isotherms were found to be more suitable than the Freundlich isotherm for correlation of equilibrium adsorption data. Acid pre-treated PWS was proven to be an effective adsorbent for dyestuff removal as compared to the other adsorbents reported in literature studies.     

Adsorption of Cu(II) ions from aqueous solutions on biochars prepared from agricultural by-products

In this study, the adsorption of Cu(II) from aqueous solutions by agricultural by-products, such as rice husks, olive pomace and orange waste, as well as compost, was evaluated. The aim was to obtain sorbent materials (biochars) through hydrothermal treatment (300?°C) and pyrolysis (300?°C and 600?°C). The effect of adsorbent dose, pH, contact time and initial Cu(II) concentration in batch-mode experiments was investigated. The optimum Cu(II) adsorption conditions was found to occur at 5-12?g/L adsorbent dose, initial pH 5-6, and reaction time 2-4?h. Furthermore, the adsorption kinetics were best described by the pseudo-second order model for all the tested materials, while the adsorption equilibrium best fitted by the linear and Freundlich isotherms. Comparing rice husks and olive pomace, the higher adsorption capacity resulted after pyrolysis at 300?°C. With respect to the orange waste and compost, the highest adsorption capacity was observed using biochars obtained after hydrothermal treatment and pyrolysis at 300?°C.     

Removal of chromium (VI) from aqueous solution using walnut hull

In this study, removal of chromium (VI) from aqueous solution by walnut hull (a local low-cost adsorbent) was studied. The extent of adsorption was investigated as a function of solution pH, contact time, adsorbent and adsorbate concentration, reaction temperature and supporting electrolyte (sodium chloride). The Cr (VI) removal was pH-dependent, reaching a maximum (97.3%) at pH 1.0. The kinetic experimental data were fitted to the first-order, modified Freundlich, intraparticle diffusion and Elovich models and the corresponding parameters were obtained. A 102.78 kJ/mol Ea (activation energy) for the reaction of chromium (VI) adsorption onto walnut indicated that the rate-limiting step in this case might be a chemically controlled process. Both the Langmuir and Freundlich isotherms were suitable for describing the biosorption of chromium (VI) onto walnut hull. The uptake of chromium (VI) per weight of adsorbent increased with increasing initial chromium (VI) concentration up to 240-480 mg/L, and decreased sharply with increasing adsorbent concentration ranging from 1.0 to 5.0 g/L. An increase in sodium chloride (as supporting electrolyte) concentration was found to induce a negative effect while an increase in temperature was found to give rise to a positive effect on the chromium (VI) adsorption process. Compared to the various other adsorbents reported in the literature, the walnut hull in this study shows very good promise for practical applicability.     

活性炭纤维对Cu2＋吸附性能的研究

研究了pH值、吸附接触时间、铜离子的初始浓度及活性炭纤维（ACF）的投加量对活性炭纤维吸附Cu2＋的影响，并选取了最佳的实验条件。用Langmuir方程和Freundlich方程拟合活性炭纤维对Cu2＋吸附等温线，结果表明：活性炭纤维吸附Cu2＋更符合Langmuir等温式，其相关系数为0．9995，以单分子层吸附为主。对活性炭纤维改性能明显提高对Cu2＋的吸附，其中效果最佳的吸附量从4．8mg／g增加到17．32mg／g，提高了3．6倍。     

Highly siliceous MCM-48 from rice husk ash for CO2 adsorption

Mesoporous MCM-48 silica was synthesized using a cationic-neutral surfactant mixture as the structure-directing template and rice husk ash (RHA) as the silica source. The MCM-48 samples were characterized by X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), N₂ physisorption and SEM. X-ray diffraction pattern of the resulting MCM-48 revealed typical pattern of cubic Ia3d mesophase. BET results showed the MCM-48 to have a surface area of 1024 m²/g and FT-IR revealed a silanol functional group at about 3460 cm⁻¹. Breakthrough experiments in the presence of MCM-48 were also carried out to test the material's CO₂ adsorption capacity. The breakthrough time for CO₂ was found to decrease as the temperature increased from 298 K to 348 K. The steep slopes observed shows the CO₂ adsorption occurred very quickly, with only a minimal mass transfer effect and very fast kinetics. In addition, amine grafted MCM-48, APTS-MCM-48 (RHA), was prepared with the 3-aminopropyltriethoxysilane (APTS) to investigate the effect of amine functional group in CO₂ separation. An order of magnitude higher CO₂ adsorption capacity was obtained in the presence of APTS-MCM-48 (RHA) compared to that with MCM-48 (RHA). These results suggest that MCM-48 synthesized from rice husk ash could be usefully applied for CO₂ removal.     

Removal of Pb(II) from wastewater using wheat bran

The adsorption of Pb(II) ions from aqueous solutions on wheat bran (WB) has been investigated as a function of initial concentration, adsorbent dose, adsorbent particle size, agitation speed, temperature, contact time and pH of solution. The equilibrium process was described well by the Langmuir isotherm model with maximum sorption capacities of 69.0, 80.7 and 87.0 mgg(-1) of Pb(II) on wheat bran at 20, 40 and 60 degrees C, respectively. Thermodynamic parameters, i.e. DeltaG(0), DeltaH(0) and DeltaS(0) have also been calculated for the system and the sorption process was found to be endothermic. Good correlation coefficients were obtained for the pseudo second-order kinetic model. The metal ion could be stripped by addition of 0.5M HCl, making the adsorbent regeneration and its reutilization possible.     

Possible Utilization of Silica Gel Sludge for the Removal of Phenol from Aqueous Solutions: Laboratory Studies

This paper discusses the adsorption capacity of silica gel sludge for phenol removal from aqueous solution. Kinetic experiments showed that phenol adsorption was completed after 2 h. Adsorption isotherms were measured for phenol from aqueous solution onto silica gel sludge under various pHs and temperatures. Results showed that the adsorption capacities for phenol was increased as pH decreased from 6.5 to 2. Temperature also was found to affect the adsorption isotherm. As temperature increases from 30 to 50°C, the adsorption capacity increases. The adsorption equilibrium of phenol on silica gel sludge was described by the linear Freundlich and Langmuir models. Furthermore, results showed that the isotherm parameters fit both linearized Langmuir and Freundlich adsorption isotherms. The Freundlich and Langmuir parameters at optimum pH was found as K _f=2.89, 1/n=0.23 and K _d=22.0, q _m=7.98, respectively. Whereas, for those at optimum temperature it was observed as K _f=2.87, 1/n=0.16 and K _d=20.93, q _m=7.91, respectively.     

Lead removal from contaminated water using mineral adsorbents

This study records experiments undertaken to determine the suitable conditions for the use of naturally occurring minerals (talc, chalcopyrite and barite) as an adsorbent for the removal of lead ions from liquid wastes. The adsorption of lead ions from solutions containing different initial lead concentrations (50, 100, 200, 400, 600, 800 and 1000 mg l^–1 Pb as lead nitrate) using different size fractions (<63 m, 63–150 m) of talc, chalcopyrite and barite at different pH (3, 5, 7 and 9) and different adsorption times (24, 48, 72 and 96 hr) was examined. The results revealed that of the studied minerals, the chalcopyrite fraction at 63–150 m showed the highest adsorption capacity. The adsorption data of Pb ions was also analyzed with the help of the Langmuir and Freundlich models to evaluate the mechanistic parameters associated with the adsorption process. The adsorption isotherms obtained from the Langmuir and Freundlich equations were generally linear and the adsorption of Pb by the studied minerals was correlated with the adsorption maximum and binding energy constant of the Langmuir equation and equilibrium partition constant and binding partition coefficient of the Freundlich equation. It was concluded that the equilibrium time of adsorption was 72 hr at an optimum pH from 7 to 9. This technique might be successfully used for the removal of lead ions from liquid industrial wastes and wastewater.     

Platinum (IV) recovery from chloride solution by functionalized acrylic copolymers

Two acrylic adsorbents with different morphological structures and bearing amidoethylenamine and thiol groups were obtained and used for platinum sorption from chloride solution by the batch method. Physico-chemical parameters that influence adsorption such as initial Pt(IV) concentration, stirring time, pH, and adsorbent amount were investigated. The thermodynamic parameters of Pt(IV) sorption on the synthesized adsorbent were also evaluated based on Langmuir and Freundlich isotherms. Thermodynamic parameters estimated from Langmuir constants indicated that the adsorption is spontaneous, exothermic and there is a disordered state at the molecular level. The models used to analyze the sorption rate led to the conclusion that the most important step in the sorption of Pt(IV) could be both particle diffusion and chemical reaction of [PtCl₆]⁻ with amine functional groups. Thus, both the ion exchange and complex formation mechanisms can occur via nitrogen atoms in the recovery of Pt(IV) on the studied adsorbent.     

Adsorption of basic dye from aqueous solution onto fly ash

The fly ash treated by H₂SO₄ was used as a low-cost adsorbent for the removal of a typical dye, methylene blue, from aqueous solution. An increase in the specific surface area and dye-adsorption capacity was observed after the acid treatment. The adsorption isotherm and kinetics of the treated fly ash were studied. The experimental results were fitted using Langmuir and Freundlich isotherms. It shows that the Freundlich isotherm is better in describing the adsorption process. Two kinetic models, pseudo-first order and pseudo-second order, were employed to analyze the kinetic data. It was found that the pseudo-second-order model is the better choice to describe the adsorption behavior. The thermodynamic study reveals that the enthalpy (ΔH⁰) value is positive (5.63 kJ/mol), suggesting an endothermic nature of the adsorption.     

Phenol removal from aqueous environments by natural & chemically modified kaolin clay

Natural, acid and base modified kaolin clays were studied for the sake of phenol and 4-chlorophenol removal from aqueous environments and their application to real ground and industrial wastewater samples. Scanning electron microscope (SEM), infrared spectroscopy (IR), X-ray diffraction (XRD), Thermo Gravimetric Analysis (TGA), Differential Thermal Analysis (DTA), and Surface area analysis were employed for characterization of the adsorbents microstructure. Operating factors such as adsorbent dose, solution pH, initial phenol concentration, and contact time were studied. The experimental data displayed that the increase of the adsorbent dose, contact time, and pH value from 2 to 7 increases the efficiency of the removal process. Optimal conditions for phenolic removal were; contact time of 300 min, primary phenol solution of 25 mg/L, pH 7 and 2.5 g/L as an appropriate adsorbent dose using crude (natural), acid modified and base modified kaolin clays. The higher phenolic removal efficiencies were obtained at 5 mg/L as 90, 97, 96.2%, respectively, for the adsorbents in the previously mentioned order. The adsorption capacity in the removal of phenol and 4-chlorophenol were 7.481 and 4.195, 8.2942 and 3.211, and 8.05185 and 18.565 mg/g, respectively, for the adsorbents in the same mentioned order. The adsorption equilibrium data were fitted and analyzed with four isotherm models, namely, Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich isotherm equations. The adsorption process of phenol on studied adsorbents was exothermic, spontaneous and thermodynamically favorable proved by the negative values of their thermodynamic parameters ΔH° and ΔG°. The correlation coefficient (R²) for all concentrations was higher than 0.94, which indicates that in the studied system, the data suitably fit the first-order kinetics. The % desorption capacity was amounted to 96%, 91.11%, and 87.06% of adsorbed phenol, respectively, for the adsorbents in the previous order using 0.1N NaOH and 10% V/V ethanol solutions as eluents at 25°C, indicating the reusability of the adsorbents. Kaolin and its modified forms can be introduced as eco-friendly and low-cost adsorbents in water remediation implementation.     

Loofa egyptiaca as a novel adsorbent for removal of direct blue dye from aqueous solution

In this paper, Loofa egyptiaca (LE), an agricultural plant cultivated in Egypt, was used to prepare low-cost activated carbon (LE_C1 and LE_C2) adsorbents. The adsorbents (LE, LE_C1 and LE_C2) were evaluated for their ability to remove direct blue 106 dye from aqueous solutions. Batch mode experiments were conducted using various parameters such as pH, contact time, dye concentration and adsorbent concentration. The surface chemistry of LE, LE_C1 and LE_C2 was analyzed by scanning electron microscopy (SEM). The experimental data were examined using Langmuir, Freundlich, Temkin and Harkins–Jura isotherms. The results showed that the adsorption of direct blue 106 was maximal at the lowest value of pH (pH = 2). Removal efficiency was increased with an increase in dye concentration and a decrease in amount of adsorbent. Maximum adsorption capacity was found to be 57.14, 63.3 and 73.53 mg/g for LE, LE_C1 and LE_C2 respectively. Kinetics were also investigated using pseudo-first-order, pseudo-second-order and intra-particle diffusion models. The experimental data fitted very well with the pseudo-first-order and pseudo-second-order kinetic models. The results indicate that LE, LE_C1 and LE_C2 could be employed as adsorbents for the removal of direct blue dye from aqueous solutions.     

Adsorption of pharmaceuticals to microporous activated carbon treated with potassium hydroxide, carbon dioxide, and steam

Adsorption of sulfapyridine, tetracycline, and tylosin to a commercial microporous activated carbon (AC) and its potassium hydroxide (KOH)-, CO-, and steam-treated counterparts (prepared by heating at 850°C) was studied to explore efficient adsorbents for the removal of selected pharmaceuticals from water. Phenol and nitrobenzene were included as additional adsorbates, and nonporous graphite was included as a model adsorbent. The activation treatments markedly increased the specific surface area and enlarged the pore sizes of the mesopores of AC (with the strongest effects shown on the KOH-treated AC). Adsorption of large-size tetracycline and tylosin was greatly enhanced, especially for the KOH-treated AC (more than one order of magnitude), probably due to the alleviated size-exclusion effect. However, the treatments had little effect on adsorption of low-size phenol and nitrobenzene due to the predominance of micropore-filling effect in adsorption and the nearly unaffected content of small micropores causative to such effect. These hypothesized mechanisms on pore-size dependent adsorption were further tested by comparing surface area-normalized adsorption data and adsorbent pore size distributions with and without the presence of adsorbed antibiotics. The findings indicate that efficient adsorption of bulky pharmaceuticals to AC can be achieved by enlarging the adsorbent pore size through suitable activation treatments.