自制固相微萃取涂层用于自来水中五氯酚的测定

采用石英毛细管作为模具,甲基丙烯酸和乙二醇二甲基丙烯酸酯在石英纤维表面原位聚合得到聚(甲基丙烯酸-乙二醇二甲基丙烯酸酯)作为固相微萃取涂层,并以五氯酚为研究对象,采用顶空SPME-GC-ECD法对该涂层的萃取性能进行评价。使用正交试验优化萃取温度、萃取时间、盐浓度、pH和搅拌速度。在最优条件下,建立了水样中五氯酚的分析方法,方法检出限为1ng/L,线性范围为2～5000ng/L,线性相关系数为0.9999,相对标准偏差(RSD,n=5)为8.9%,加标回收率为110.8%。     

Development of an enzyme-linked immunosorbent assay for screening contamination by chlorophenols in environmental waters

The development of an immunoassay for screening contamination by chlorophenols is presented. Two haptens were synthesized and conjugated to immunizing proteins to raise rabbit polyclonal antibodies. The antibody-coated format (direct) gave better sensitivity than the conjugate-coated format (indirect) if 2,4,6-trichlorophenol is used as target analyte. The measurement range was 86.4 microg l(-1) to 0.7 microg l(-1), with an average I50 of 7.8 microg l(-1) and a detection limit of 0.2 microg l(-1). The assay detects the presence of trichloropyridinol and other chlorophenols such as di-, tetra- and pentachlorophenols constituting thus a suitable tool for the early warning of the presence of such family contaminants. The optimized method permits the detection of the most important chlorophenols in a fast and reproducible way using no more than one antibody and a single assay. The results achieved with water samples spiked with different chlorophenols fit with a multiple linear regression model when expressing the total concentration of chlorophenols as equivalent of 2,4,6-trichlorophenol (P < 0.01), demonstrating the usefulness of the assay as a screening tool to detect contamination by chlorophenols.     

Survey of the occurrence of residues of methyl tertiary butyl ether (MTBE) in Dutch drinking water sources and drinking water

An indicative survey has been carried out in The Netherlands investigating the presence of methyl tertiary butyl ether (MTBE) in drinking water and the corresponding sources. In total, 71 different sites used for the preparation of drinking water in The Netherlands were sampled in two successive seasons in 2001 involving the analysis of 156 samples. (ground water (n = 88), surface water (n = 17), bank filtrate water (n = 6) and drinking water (n = 45)). To combine high sample throughput with high selectivity and sensitivity, off-line purge and trap for sampling and gas chromatography mass spectrometry equipped with an automated thermal desorption sampler (TDS-GC-MS) was selected as the preferred analytical methodology. The developed procedure enabled the analysis of at least 40 samples per day and provided a limit of quantification of 2 ng l(-1). In the first period 63 samples of raw water were analyzed. Concentrations ranged between < 10 ng l(-1) and 420 ng l(-1) with a median concentration below 10 ng l(-1). The second period was focused at the re-sampling of positive locations (MTBE > 10 ng l(-1)) and a few additional drinking water utilities of which both the raw and drinking water of the utilities were analyzed. The median concentration of MTBE in the selected set of drinking water samples was 20 ng l(-1) (n = 45). At one location MTBE was found at a level of 2900 ng l(-1) caused by point source contamination of the ground water (11 900 ng l(-1)). Special attention has been paid to the quality of the results by analyzing all samples in duplicate and the analysis of control samples during each series of analyses.     

Sequential Determination of Trace Metals in Sea Water by Inductively Coupled Plasma Mass Spectrometry After Electrothermal Vaporization of their Dithiocarmabamate Complexes in Methyl Isobutyl Ketone

A sensitive method for sequential determination of V, Mn, Fe, Co, Ni, Cu, Zn, Mo and Sb in sea water using an inductively coupled plasma mass spectrometry (ICP-MS) after electrothermal vaporization of their dithiocarbamate complexes in methyl isobutyl ketone (MIBK) has been investigated. All analyte elements were simultaneously concentrated 20 fold in a single extract and introduced into the plasma using a graphite rod electrothermal vaporizer (ETV). A sensitivity enhancement due to a chemical modification using a mixed modifier of palladium nitrate and magnesium nitrate was observed for all analyte elements. The limits of detection of the method ranged from 2 ng l-1 for Co to 329 ng l-1 for V. For the replicate determinations of the analyte elements in a sea water sample, the repeatability was within 10% (as a coefficient variation), except for V (12.8%). The recovery test performed on a sea water sample resulted in values ranging from 87% for Sb to 119% for V. With the exception of Mo, the application of this method for the determination of the analyte elements in sea water samples collected from the surface to the depth of 5000 m at the sampling station of 34°12.08N, 141°57.50E (Oct. 12, 1994) in the northwest Pacific Ocean resulted in vertical distributions and concentration ranges which were in a good agreement with those reported in literatures.     

Natural abundance of Sb and Sc in pristine groundwaters, Springwater Township, Ontario, Canada, and implications for tracing contamination from landfill leachates

Using ICP-SMS and the clean lab methods and procedures developed for determining trace element concentrations in polar snow and ice, a lower limit of detection (LOD) of 30 pg l(-1) for Sb and 5 pg l(-1) for Sc was achieved, allowing the natural abundances of Sb and Sc to be measured in pristine groundwaters. Water samples were collected from natural flows and wells between Elmvale and Wyevale in Springwater Township, Ontario, Canada. The water in this region is derived from chemical reactions between meteoric fluids and the Quaternary sediments which cover the bedrock (dolomitic limestone) to depths of more than 100 m. The chemical composition of these waters (pH 8) is primarily a reflection of reactions between the percolating fluids with calcite and dolomite. The maximum concentration of Sb was 5.0 ng l(-1), and the average of all samples collected was 2.2 +/- 1.2 ng l(-1) (n = 34). The average concentration of Sc was 8.6 +/- 4.7 ng l(-1) (n = 28). The paucity of published Sb concentration data available for comparison is probably because most of the analytical methods commonly used to date, including GFAAS, HG-AAS, HG-AFS, INAA, and ICP-QMS, have lower limits of detection which are inadequate for reliably determining the natural abundance of Sb in many uncontaminated groundwaters. Also, the measurement of extremely low concentrations of Sb requires extra care to avoid possible contamination. Given the extensive use of Sb in plastics, we show that some of the containers used to collect and store samples, and for handling and preparing samples for chemical analyses, may be important sources of contamination in the laboratory. The Sb and Sc concentrations reported here should serve as reference values for this region, against which contamination by various human impacts in future could be compared.     

Determination of organophosphorus pesticides and related compounds in water samples by membrane extraction and gas chromatography

A membrane extraction-gas chromatography method was developed fordetermination of organophosphorus pesticides and related compounds including methamidophos, DDVP, dimethoate, methyl parathion, parathion, thiophosphoric acid trimethyl ester, and thiophosphoramidic acid dimethyl ester in water samples. In thismethod, surface-modified acetic cellulose membranes were used to extract the target analytes in water samples, the extracted analytes were back-extracted into a small amount of methanol, andgas chromatography with pulsed flame photometric detector (GC-PFPD) was used to determine the concentrations of targetanalytes in the extracts. The recoveries obtained for thetarget analytes spiked into the water samples ranged from 66to 94%. The method detection limit for each target analyte was 0.05 g L^-1. The method developed in this study had shown the advantages of being cheap, simple, fast, and reliable. It had been used successfully to determine the concentrations of target analytes in river water samples.     

Bio-analytical and chemical characterisation of offshore produced water effluents for estrogen receptor (ER) agonists

The in vitro estrogen receptor (ER) agonist potency and C1 to C9 alkyl substituted phenol content of offshore produced water effluents collected from the UK sector of the North Sea were determined using a combination of bio-analytical and chemical analysis techniques. An in vitro reporter gene assay was used to determine ER agonist potency, whilst gas chromatography coupled to mass spectrometry (GC-MS) was used to quantify the concentration of alkylphenols. The in vitro ER agonist potency was highly variable and ranged from less than the limit of detection (theoretically 0.03 ng 17beta-estradiol (E2) l(-1)) to 91 ng E2 l(-1). C1 to C5 alkylphenol concentrations were also highly variable ranging from 5 to 1600 microg l(-1) with a median concentration of 206 microg l(-1). These data reflect the highly variable composition of produced water discharges from different fields. The observed poor correlation of the alkylphenol isomer content and ER agonist activity suggests that other compounds present in the produced water discharges may be responsible for the ER agonist activity observed. It is recommended that further work be performed to characterise the full range of ER agonists present in offshore produced water discharges.     

Direct on-filter assay of subtilisin-type proteolytic enzymes for rapid analysis of analyte captured from the workplace atmosphere

A simple assay for some proteolytic enzymes has been developed which can be performed directly on the surface of a cellulose nitrate filter used to capture the analyte during workplace monitoring for health and safety purposes. Following air sampling the analysis is performed on the filter which is retained within the air sampler. This involves two steps: first, a 15 min incubation in which the captured enzyme is dissolved and then digests an alkaline-phosphatase-labelled antibody immobilised as a small dot on the surface of the filter; and second, is a 10 min incubation with substrate solution, which follows an in situ wash under a vacuum. During the incubation colour develops on the spot at the location of the immobilised enzyme antibody conjugate. The intensity of the spot can be assessed visually within the sampler to ascertain the presence or absence of captured enzyme, or alternatively quantitative results can be obtained using an optical scanner. The limit of detection is 5 ng per filter for subtilisin (20 ng for visual discrimination between this standard and the zero). The assay is stable to the effects of ambient air sampling at 31 min(-1) for 18 h.     

毛细管低温吸附气相色谱法同时测定空气中痕量甲硫醇和硫化氢

建立了毛细管低温吸附气相色谱同时测定空气中痕量甲硫醇和硫化氢的方法，介绍了冷冻吸附装置的制备方法和样品冷凝吸附流程。甲硫醇和硫化氢分别在0.467ng～5.16ng和0.327ng～3.60ng范围内线性良好，当进样体积为1L时，检出限为0．205μg/m^3和0．213μg／m^3，空白加标平均回收率为88．6％和90．2％，RSD为6.0％和6．5％。     

超高效液相色谱串联质谱法测定水体中17种抗生素

建立了一种超高效液相色谱串联质谱法同时测定饮用水源中17种超痕量水平抗生素的分析方法。采用Oasis HLB柱对500 mL pH=5含目标物的水样进行富集，干燥15 min后，用5%氨水甲醇洗脱，氮吹后定容至1 mL。用C₁₈柱吸附目标物，并用0.1%甲酸水和甲醇对目标物进行分离，采用正离子电喷雾电离模式在多反应监测通道中对目标物同时进行分析。该方法检出限为0.07~0.78 ng/L，超痕量水平下回收率范围为75.8%~108%。该方法灵敏度高，精密度为1.8%~15.0%，适用于同时测定饮用水源等水体中的抗生素。     

Determination of copper in biological samples by flame atomic absorption spectrometry after precipitation with Me-BTAP

A simple and sensitive method was developed for determination of trace copper by direct precipitation preconcentration and detection with Flame Atomic Absorption Spectrometry (FAAS). The reagent 2-[2'-(6-methyl-benzothiazolylazo)]-4-aminophenol (Me-BTAP) was used as precipitating agent. The experimental conditions for the quantitative precipitation of copper, such as pH, amount of reagents, temperature and the effect of diverse ions on the precipitation have been investigated. It was found that copper is quantitatively extracted (> or =95%) and the method provides a sensitivity enhancement of 40-fold for a 10 ml sample volume with a detection limit of 0.5 microg l(-1). The proposed method was successfully applied for the determination of trace copper in water, urine and biological samples.     

液相色谱-串联质谱法测定水体、沉积物及土壤中全氟化合物

建立了水、沉积物及土壤中13种全氟化合物(PFCs)的富集、净化、浓缩的前处理方法及快速液相色谱三重四级杆串联质谱的分析方法。9种全氟羧酸、2种典型全氟磺酸、2种磺酰铵衍生前体物的响应因子与质量浓度的线性关系良好。添加回收实验表明,13种全氟化合物在水、土壤和沉积物中的回收率为52.3%~119.3%,变异系数为2.3%~19.4%,方法检出限分别为0.015~0.472 ng/L、0.012~0.875 ng/g、0.004~0.743 ng/g。该法成功应用于实际样品的测定,沉积物和土壤中分别检测到3种和10种全氟化合物。     

Determination of ultra-trace amounts of cadmium by ET-AAS after column preconcentration with a new sorbent of modified MWCNTs

The present research reports on the application of modified multiwalled carbon nanotubes as a new, easily prepared, and stable solid sorbent for the column preconcentration of ultra-trace amounts of cadmium in aqueous solution. Multiwalled carbon nanotubes were oxidized with concentrated HNO₃ and modified with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol and then were used as a solid phase for the column preconcentration of Cd(II). Elution was carried out with 0.5 mol?L^?1 HNO₃. The amount of eluted Cd(II) was measured using electrothermal atomic absorption spectrometry. Various parameters such as pH, sample and eluent flow rate, eluent concentration, breakthrough volume, and interference of a great number of anions and cations on the retention of analyte on sorbent were studied. Under the optimized conditions, the calibration graph was linear in the range of 0.67 ng?L^?1 to 5.0 μg?L^?1 and the detection limit (3S_b, n?=?7) was 0.14 ng?L^?1 in initial solution. A preconcentration factor of 300 and relative standard deviations of ±3.6 % for seven successive determinations of 3 ng of Cd(II) were achieved. The column preconcentration was successfully applied to the analysis of river water, waste water, and Persian Gulf water sample.     

加速溶剂同时萃取和净化-气相色谱-三重四极杆串联质谱测定土壤和沉积物中8种多溴联苯醚

建立了土壤和沉积物中8种多溴联苯醚(PBDEs,BDE-28、BDE-47、BDE-99、BDE-100、BDE-153、BDE-154、BDE-183和BDE-209)加速溶剂同时萃取和净化-气相色谱-三重四极杆串联质谱(ASE-GC-MS-MS)的分析方法。通过优化加速溶剂萃取与弗罗里硅土在线净化和串联质谱多反应监测模式的条件,较好地去除基质干扰,并提高了三重四极杆串联质谱定性的准确性及定量的灵敏性。该方法采用改进的色谱柱能同时分析包括高溴代联苯醚BDE-209在内的8种PBDEs,其浓度范围为1～100 ng/mL(BDE-209为10～1 000 ng/mL),线性良好,线性回归系数均大于0.997。方法检出限为0.004～0.1 ng/g,方法回收率为75%～110%,方法精密度为2.4%～15.6%。适于批量处理土壤和沉积物中含有多组分痕量PBDEs的样品。     

Development and validation of methods for environmental monitoring of cyclophosphamide in workplaces

Methods to monitor contamination of workplaces with antineoplastic drugs have been developed and validated. Cyclophosphamide (CP) was used as a model compound as it is one of the most commonly used antineoplastic drugs. A wipe sampling method to detect contamination with CP at surfaces was developed. A personal air sampling method to sample gas and vapour on solid sorbent tubes and particles with filters was also developed. Wipe and filter samples were extracted and sorbent samples were eluted, all with ethyl acetate. The samples were analysed with liquid chromatography tandem mass spectrometry. (2)H(6)-labelled cyclophosphamide was used as an internal standard. The between-day precision was 2-5% for wipe samples, 4-6% for sorbent samples and 3-8% for filter samples. The limit of detection was 0.02 ng CP per sample for the wipe and filter methods and 0.03 ng CP per sample for the solid sorbent method. Wipe sampling on surfaces made of different materials resulted in mean recoveries between 78-106%. The desorption recovery was between 97-102% for the wipe samples, 97% for the sorbent samples and 101% for the filter samples. Samples were stable for up to 2 months at 5 degrees C and -20 degrees C and for about 2 d at room temperature. The developed methods were applied to the measurement of contamination with CP in a hospital pharmacy. Trace amounts of CP, 1.3 and 1.4 ng, were detected on surfaces in the pharmacy.     

On-line solid phase extraction with polyurethane foam: trace level spectrophotometric determination of iron in natural waters and biological materials

This paper reports the development of a simple and accurate on-line procedure for preconcentration and determination of dissolved iron in waters and biological materials using unloaded polyether-type polyurethane foam as solid extractor. In the developed flow injection system, the analyte was preconcentrated from acidic aqueous medium as iron-thiocyanate complex with post-elution with ascorbic acid solution and spectrophotometric measurement with 1,10-phenanthroline as colorimetric reagent. In order to improve the performance of the system several chemical and flow variables were investigated as well as the effect caused by the presence of possible interferents. The method was validated by the analysis of two certified reference materials. Application of the methodology was carried out by the determination of dissolved iron content in eight natural water samples with different characteristics. The results were compared with those obtained by electrothermal atomic absorption spectrometry (ETAAS) and no statistical difference was observed. The detection limit was 0.75 microgram l-1 and the RSD was 1.2% for 2 min preconcentration time. At this condition, a productivity of 20 samples h-1 was achieved. Increasing the preconcentration time up to 3 min, a detection limit of 0.45 microgram l-1, an RSD of 1.5% and an analytical throughput of 15 h-1 were verified.     

Dynamics of steroid estrogen daily concentrations in hospital effluent and connected waste water treatment plant

Hospital effluent and connected waste water treatment plant (WWTP) influent and effluent were sampled daily to determine the levels and inter-day variations of three naturally occurring steroid estrogens: estrone, 17β-estradiol, estriol, and synthetic 17α-ethinylestradiol. After solid phase extraction, interferences were removed with a silica gel clean-up step and the samples analysed using gas chromatography with mass selective detection (GC-MSD). The determined inter-day concentrations in hospital effluent were between 8.6 to 31.3 ng L(-1) for estrone, 相似文献   

Monitoring of polychlorinated biphenyl contamination and estrogenic activity in water, commercial feed and farmed seafood

We evaluated the concentration and congener distribution of seven "target" polychlorinated biphenyls (PCBs) present in water collected in different aquaculture farms of the Mediterranean area, commercial feeds, and farmed seafood. PCBs were present in feed and in tissues of all the analysed organisms at levels ranging from 1.96 ng g(-1) to 124.00 ng g(-1) wet weight, and in 10.5% of the water samples, at levels from under detection limit to 33.0 ng l(-1) with total PCB concentrations significantly higher in samples from the Tyrrhenian Sea than the Adriatic Sea. PCB congener distribution in tissues resembled that of feed, suggesting that commercial feed is an important source of PCBs. The estrogenicity of organic extracts of the samples was also evaluated by using an in vitro yeast reporter assay. Estrogenic activity higher than 10% of the activity induced by 10 nM 17 beta-estradiol was observed in 20.0% of seafood samples and 15.8% of water samples. Seafood and water samples from the Tyrrhenian Sea were more frequently estrogenic than the Adriatic ones (16.45 versus 4.08%). A significant correlation of total PCB concentrations on biological activity was observed for sea bass and mussels from the Adriatic Sea (p < 0.045 and p < 0.04, respectively), and for sea bass of the Tyrrhenian Sea (p = 0.05). These results indicate the need of an integral approach in the exposure assessment to potential toxic compounds for human via food.     

Contamination of Canadian and European bottled waters with antimony from PET containers

Using clean lab methods and protocols developed for measuring Sb in polar snow and ice, we report the abundance of Sb in fifteen brands of bottled water from Canada and forty-eight from Europe. Comparison with the natural abundance of Sb in pristine groundwaters, water bottled commercially in polypropylene, analyses of source waters prior to bottling, and addition of uncontaminated groundwater to PET bottles, provides unambiguous evidence of Sb leaching from the containers. In contrast to the pristine groundwater in Ontario, Canada containing 2.2 +/- 1.2 ng l(-1) Sb, 12 brands of bottled natural waters from Canada contained 156 +/- 86 ng l(-1) and 3 brands of deionized water contained 162 +/- 30 ng l(-1); all of these were bottled in PET containers. Natural water from Ontario bottled in polypropylene contained only 8.2 +/- 0.9 ng l(-1). Comparison of three German brands of water available in both glass bottles and PET containers showed that waters bottled in PET contained up to 30 times more Sb. To confirm that the elevated Sb concentrations are due to leaching from the PET containers, water was collected in acid-cleaned LDPE bottles from a commercial source in Germany, prior to bottling; this water was found to contain 3.8 +/- 0.9 ng l(-1) Sb (n = 5), compared with the same brand of water purchased locally in PET bottles containing 359 +/- 54 ng l(-1) (n = 6). This same brand of water in PET bottles, after an additional three months of storage at room temperature, yielded 626 +/- 15 ng l(-1) Sb (n = 3). Other German brands of water in PET bottles contained 253-546 ng l(-1) Sb (n = 5). The median concentration of Sb in thirty-five brands of water bottled in PET from eleven other European countries was 343 ng l(-1) (n = 35). As an independent check of the hypothesis that Sb is leaching from PET, the pristine groundwater from Canada (containing 2.2 +/- 1.2 ng l(-1) Sb) was collected from the source using PET bottles from Germany: this water contained 50 +/- 17 ng l(-1) Sb (n = 2) after only 37 days, even though it was stored in the refrigerator, and 566 ng l(-1) after six months storage at room temperature.     

Solid-phase extraction followed by liquid chromatography-time-of-flight-mass spectrometry to evaluate pharmaceuticals in effluents. A pilot monitoring study

The present work provides a multi-residue analytical method for determining a selection of 20 pharmaceuticals from diverse therapeutical classes in hospital effluent wastewater. The method is based on the simultaneous extraction of the target compounds by solid phase extraction (SPE), followed by liquid chromatography-time-of-flight-mass spectrometry (LC-TOF-MS) analysis. Using TOF-MS, accurate mass measurements within 2 ppm error were obtained for most of the pharmaceuticals studied. Empirical formula information can be obtained by this method, allowing the unequivocal identification of the target compounds in the samples. Validation studies showed that LC-TOF-MS analysis is a valuable new tool for identification and quantification of pharmaceuticals in wastewater. Recoveries, using Oasis HLB cartridges at pH 7, were higher than 75% for all pharmaceuticals, except for ranitidine, 4-methylaminoantipyrine (4-MAA), cefotaxime and omeprazole, which needed specific pH conditions for their extraction. Linearity of response over two orders of magnitude was demonstrated (r > 0.99). Matrix effects resulting in suppression of the response were observed. For most of the compounds ion suppression was less than 39%, except for metronidazole, carbamazepine 10,11-epoxide, naproxen and erythromycin, where the signal suppression was 42%, 59%, 46% and 95%, respectively. A simple and effective approach to minimize or avoid matrix interferences was the 1 : 4 dilution of the SPE extracts. Method detection limits (MDLs) and quantification limits (MQLs) ranged between 4-115 ng l(-1) and 14-384 ng l(-1), respectively. The precision of the method, calculated as relative standard deviation (RSD), ranged from 1.1-19.8% and 1.7-21.7% for intra- and inter-day, respectively. The developed analytical method was applied to the analysis of hospital effluent wastewater during a survey study. 18 of the 20 pharmaceuticals studied were detected at concentration levels of microg l(-1), reaching in some cases concentrations over 100 microg l(-1), and in the case of the analgesic and antipyretic dipyrone metabolite, higher than 1000 microg l(-1).