Bacterial degradation of acetone in an outdoor model stream

Diurnal variations of the acetone concentration in an outdoor model stream were measured with and without a nitrate supplement to determine if the nitrate supplement would stimulate bacterial degradation of the acetone. Acetone loss coefficients were computed from the diurnal data using a fitting procedure based on a Lagrangian particle model. The coefficients indicated that bacterial degradation of the acetone was occurring in the downstream part of the stream during the nitrate addition. However, the acetone concentrations stabilized at values considerably above the limit of detection for acetone determination, in contrast to laboratory respirometer studies where the acetone concentration decreased rapidly to less than the detection limit, once bacterial acclimation to the acetone had occurred. One possible explanation for the difference in behavior was the limited 6-hour residence time of the acetone in the model stream.     

Effects of cross-substrate interaction on biotrickling filtration for the control of VOC emissions

The effects of cross-substrate interaction to the performance of a gas-phase biotrickling filter for treating a mixture of volatile organic compounds (VOCs), including three structural heterologous in acetone, toluene, and trichloroethylene, were investigated. The biotrickling filter was inoculated with microbial consortium containing at least seven bacterial species utilizing either acetone or toluene, or both, as their carbon sources. In the performance study, the column operating under variable conditions typifying the waste gas emission from the microelectronics fabrication processes achieved a total hydrocarbon (THC) removal efficiency in excess of 85% and a mineralization capacity over 50% for THC mass loading as high as 36.2 g-CH4 m-3h-1. The cross-substrate effects were examined by correlating the relative changes in the mass removal of each substrate with the biodegradative capability of the microbial consortium. The degradation of trichloroethylene was primarily due to co-metabolism by the toluene-oxidizing enzymes, but the results also indicated that trichloroethylene partially induced its own degradation. Concentration increases in acetone appeared to cause a diauxie effect that suppressed degradation of toluene and trichloroethylene, and shifted the microbial population toward the selective acetone-degraders. No irrecoverable toxicity or inhibitory effects were observed throughout the experiments. These results suggest that the relative VOC concentration in the waste gas mixture is a factor as important as the biodegradative function of the microbial consortium, and thus should be carefully evaluated to satisfy the treatment objectives.     

Photodegradation and volatility of pesticides

BACKGROUND AND OBJECTIVES: Among the factors affecting the environmental fate of surface-applied pesticides several biological as well as abiotic factors, such as volatilization and photochemical transformations are of particular interest. Whereas reliable measurement methods and models for estimating direct photodegradation are already available for the compartments of water and atmosphere and individual subprocesses have already been described in detail, there is still a need for further elucidation concerning the key processes of heterogeneous photodegradation of environmental chemicals on surfaces. METHODS: In order to systematically examine the direct and indirect photodegradation of 14C-labeled pesticides on various surfaces and their volatilization behavior, a new laboratory device ('photovolatility chamber') was designed according to US EPA Guideline 161-3. Model experiments under controlled conditions were conducted investigating the impact of different surfaces, i.e. glass, soil dust and radish plants, and environmental factors, i.e. irradiation and atmospheric ozone (O3), on the photodegradation and volatilization of surface-deposited [phenyl-UL-14C]parathion-methyl (PM). RESULTS AND DISCUSSION: Depending on the experimental conditions, parathion-methyl was converted to paraoxon-methyl, 4-nitrophenol, unknown polar products and 14CO2. With respect to the direct photodegradation of PM (experiments without O3), the major products were polar compounds and 14CO2, due to the rapid photochemical mineralization of 4-nitrophenol to 14CO2. Paraoxon-methyl and 4-nitrophenol formation was mainly mediated by the combination of light, O3, and *OH radicals. In radish experiments PM photodegradation was presumably located in the cuticle compartment, which exhibited a sensitized photodegradation, as more unknown products were yielded compared to the glass and soil dust experiments. This could be explained by intensifying the inherent PM degradation in the dark with the same product spectrum. Due to photochemical product formation, which is an antagonistic process to the volatilization of parent compound, the volatilization of unaltered parathion-methyl from each surface generally decreased in the presence of light, particularly in combination with increasing O3 concentrations and *OH radical production rates. CONCLUSION: First results demonstrated that the photovolatility chamber provides a special tool for the systematic evaluation of (a) photodegradation of surface-located pesticide residues, i.e. measuring qualitative aspects of direct and indirect photodegradation together with relative photodegradation rates, and (b) volatilization of pesticides on surfaces by including and optionally varying relevant parameters such as light, atmospheric O3 concentration, surface temperature, air temperature, air flow rate. OUTLOOK: The experimental facility represents an important complement to lysimeter and field studies, in particular for experiments on the volatilization of pesticides using the wind tunnel system. With the photovolatility chamber special experiments on photodegradation, volatilization and plant uptake can be conducted to study key processes in more detail and this will lead to a better understanding of the effects of certain environmental processes on the fate of released agrochemicals contributing to an improved risk assessment.     

Fates and transport of PPCPs in soil receiving reclaimed water irrigation

Fates and transport of 9 commonly found PPCPs of the reclaimed water were simulated based on the HYDRUS-1D software that was validated with data generated from field experiments. Under the default scenario in which the model parameters and input data represented the typical conditions of turf grass irrigation in southern California, the adsorption, degradation, and volatilization of clofibric acid, ibuprofen, 4-tert-octylphenol, 4-n-nonylphenol, naproxen, triclosan, diclofenac sodium, bisphenol A and estrone in the receiving soils were tracked for 10 years. At the end, their accumulations in the 90 cm soil profile varied from less than 1 ng g⁻¹ to about 140 ng g⁻¹ and their concentrations in the drainage water in the 90 cm soil depth varied from nil to μg L⁻¹ levels. The adsorption and microbial degradation processes interacted to contain the PPCPs entirely within surface 40 cm of the soil profiles. Leaching and volatilization were not significant processes governing the PPCPs in the soils. The extent of accumulations in the soils did not appear to produce undue ecological risks to the soil biota. PPCPs did not represent any potential environmental harm in reclaimed water irrigation.     

Dissipation of triadimefon on the solid/gas interface.

The dissipation of triadimefon, as pure solid and in the Bayleton 5 commercial formulation, was studied under controlled and natural conditions. Volatilization and photodegradation were shown to be the main dissipation processes. The volatilization results can be described by an empirical model assuming exponential decay of the volatilization rate. The filler of the commercial formulation is determinant for the volatilization but has little effect on the photodegradation rates. The main photoproducts were identified and a reaction mechanism proposed.     

光催化降解模拟室内挥发性有机污染物研究

用浸渍-提拉法制备玻璃弹簧负载型TiO2薄膜催化剂,在自制的反应器中进行光催化降解由丙酮、甲苯、对二甲苯组成的模拟室内挥发性有机污染物VOCs研究.研究发现:催化剂中掺杂金属离子能影响催化剂的降解效果,降解效果依次为掺铈TiO2＞纯TiO2＞掺银TiO2;气体流量显著影响降解效果,丙酮、甲苯和对二甲苯的最佳降解流量分别为3、5、7 L/min;混合气体中非对称性的极性分子的降解效率高于对称性分子,导致丙酮、对二甲苯组分降解率降低,甲苯降解率增高.     

Modelling pesticide volatilization after soil application using the mechanistic model Volt'Air

Volatilization of pesticides participates in atmospheric contamination and affects environmental ecosystems including human welfare. Modelling at relevant time and spatial scales is needed to better understand the complex processes involved in pesticide volatilization. Volt'Air-Pesticides has been developed following a two-step procedure to study pesticide volatilization at the field scale and at a quarter time step. Firstly, Volt'Air-NH₃ was adapted by extending the initial transfer of solutes to pesticides and by adding specific calculations for physico-chemical equilibriums as well as for the degradation of pesticides in soil. Secondly, the model was evaluated in terms of 3 pesticides applied on bare soil (atrazine, alachlor, and trifluralin) which display a wide range of volatilization rates. A sensitivity analysis confirmed the relevance of tuning to K_h. Then, using Volt'Air-Pesticides, environmental conditions and emission fluxes of the pesticides were compared to fluxes measured under 2 environmental conditions. The model fairly well described water temporal dynamics, soil surface temperature, and energy budget. Overall, Volt'Air-Pesticides estimates of the order of magnitude of the volatilization flux of all three compounds were in good agreement with the field measurements. The model also satisfactorily simulated the decrease in the volatilization rate of the three pesticides during night-time as well as the decrease in the soil surface residue of trifluralin before and after incorporation. However, the timing of the maximum flux rate during the day was not correctly described, thought to be linked to an increased adsorption under dry soil conditions. Thanks to Volt'Air's capacity to deal with pedo-climatic conditions, several existing parameterizations describing adsorption as a function of soil water content could be tested. However, this point requires further investigation. Practically speaking, Volt'Air-Pesticides can be a useful tool to make decision about agricultural practices such as incorporation or for the estimation of overall pesticide volatilization rates, and it holds promise for time specific dynamics.     

Modelling the fate of organic chemicals in the soil plant environment: Model study of root uptake of pesticides

The fate of organic chemicals in the soil-plant-atmosphere environment and the governing processes were studied with a coupled dynamic soil transport and plant compartment model. Scenarios with applications of pesticides on sand and loam soils with chemical uptake in barley and wheat were used in the model calculations. Root uptake and concentrations in the plant compartments stem, leave and fruit were calculated for the pesticides terbuthylazine, isoproturon and carbofuran.

The effectivity of uptake from soils with different soil sorption coefficients had been shown for sand and loam soils. The processes degradation in plant and volatilization from leaves to atmosphere are especially effective for carbofuran and terbuthylazine. Although the concentrations in corn at harvest are lower than the maximum allowed concentrations, the peak concentrations in the course of the vegetation period are significantly higher (factor ≤ 200).     

Measurements of acetone and other gas phase product yields from the OH-initiated oxidation of terpenes by proton-transfer-reaction mass spectrometry (PTR-MS)

The atmospheric oxidation of several terpenes appears to be a potentially relevant source of acetone in the atmosphere. Proton-transfer-reaction mass spectrometry was used as an on-line analytical method in a chamber study to measure acetone and other gas phase products from the oxidation of α- and β-pinene initiated by OH radicals in air and in the presence of NO_x.Acetone may be formed promptly, following attack by the OH radical on the terpene, via a series of highly unstable radical intermediates. It can also be formed by slower processes, via degradation of stable non-radical intermediates such as pinonaldehyde and nopinone.Primary acetone and pinonaldehyde molar yields of 11±2% (one σ) and 34±9% (one σ), respectively, were found from the reaction between α-pinene and the OH radical. After all α-pinene had been consumed, an additional formation of acetone due to the degradation of stable non-radical intermediates was observed. The total amount of acetone formed was 15±2% (one σ) of the reacted α-pinene. An upper limit of 12±3% (one σ) for the acetone molar yield from the oxidation of pinonaldehyde was established.From the reaction between β-pinene and the OH radicals, primary acetone and nopinone molar yields of 13±2% (one σ) and 25±3% (one σ), respectively, were observed. Additional amounts of acetone were formed by the further degradation of the primary product, such as the most abundant product nopinone. The total amount of acetone formed was 16±2% (one σ) of the reacted β-pinene. An upper limit of 12±2% (one σ) for the acetone molar yield from the oxidation of nopinone was established.The observed product yields from α- and β-pinene are in good agreement with other studies using mass-spectrometric and gas chromatographic analytical techniques, but differ significantly from previous studies using spectroscopic methods. Possible reasons for the discrepancies are discussed.     

Modeling effects of moisture content and advection on odor causing VOCs volatilization from stored swine manure

Two models for evaluating the contents and advection of manure moisture on odor causing volatile organic compounds (VOC-odor) volatilization from stored swine manure were studied for their ability to predict the volatilization rate (indoor air concentration) and cumulative exposure dose: a MJ-I model and a MJ-II model. Both models simulating depletion of source contaminant via volatilization and degradation based on an analytical model adapted from the behavior assessment model of Jury et al. In the MJ-I model, manure moisture movement was negligible, whereas in the MJ-II model, time-dependent indoor air concentrations was a function of constant manure moisture contents and steady-state moisture advection. Predicted indoor air concentrations and inhaled doses for the study VOC-odors of p-cresol, toluene, and p-xylene varied by up to two to three orders of magnitude depending on the manure moisture conditions. The sensitivity analysis of both models suggests that when manure moisture movement exists, simply MJ-I model is inherently not sufficient to represent a more generally volatilization process, which can even become stringent as moisture content increases. The conclusion illustrates how one needs to include a wide variety of manure moisture values in order to fully assess the complex volatilization mechanisms that are present in a real situation.     

Behaviour of DDT under laboratory and outdoor conditions in Germany

Abstract

Experiments were conducted on adsorption, volatilization and UV‐degradation of p,p'‐DDT on soil surface, and leaching and degradation in sand columns. p,p'‐DDT was shown to adsorb stronger to soils with higher organic content. UV irradiation at 290 nm for 10 hours mineralized less than 0.1% of DDT in soil.

Results show that only 0.1% of DDT volatilized in a sun‐exposed semi‐closed quartz system. Polar compounds accounted from 1.4% after 55 days. The rate of volatilization and degradation in an open system was much higher; only 15% DDT and 7% DDE were recovered after 6 weeks in the organic extract. p,p'‐DDT was adsorbed to a great extent on the top layers of sand columns; 86% in the top 8 cm.     

Study of metabolites from the degradation of polycyclic aromatic hydrocarbons (PAHs) by bacterial consortium enriched from mangrove sediments

The PAH metabolites produced during degradation of fluorene, phenanthrene and pyrene by a bacterial consortium enriched from mangrove sediments were analyzed using the on-fiber silylation solid-phase microextraction (SPME) combining with gas chromatography–mass spectrometry (GC–MS) method. Seventeen metabolites at trace levels were identified in different PAH degradation cultures based on the full scan mass spectra. In fluorene degradation cultures, 1-, 2-, 3- and 9-hydroxyfluorene, fluorenone, and phthalic acid were detected. In phenanthrene and pyrene degradation cultures, various common metabolites such as phenanthrene and pyrene dihydrodiols, mono-hydroxy phenanthrene, dihydroxy pyrene, lactone and 4-hydroxyphenanthrene, methyl ester, and phthalic acid were found. The detection of various common and novel metabolites demonstrates that SPME combining with GC–MS is a quick and convenient method for identification as well as monitoring the real time changes of metabolite concentrations throughout the degradation processes. The knowledge of PAH metabolic pathways and kinetics within indigenous bacterial consortium enriched from mangrove sediments contributes to enhance the bioremediation efficiency of PAH in real environment.     

Diversity of chlorobiphenyl-metabolizing bacteria and their biphenyl dioxygenases in contaminated sediment

Bacteria and bacterial communities in sites contaminated with polychlorinated biphenyls have been extensively studied in the past decades. However, there are still major gaps in the knowledge of environmental processes, especially in the behavior of previously described bacteria in vitro, their real degradation abilities and the enzymes that are involved in the degradation processes.     

Effect of a cationic surfactant on the volatilization of PAHs from soil

Purpose

Cationic surfactants are common in soils because of their use in daily cosmetic and cleaning products, and their use as a soil amendment for the mitigation and remediation of organic contaminated soils has been proposed. Such surfactant may affect the transfer and fate of organic contaminants in the environment. This study investigated the effect of a cationic surfactant, dodecylpyridinium bromide (DDPB), on the volatilization of polycyclic aromatic hydrocarbons (PAHs) from a paddy soil.

Materials and methods

The volatilization of PAHs from moist soil amended with different concentrations of DDPB was tested in an open system. The specific effects of DDPB on the liquid?Cvapor and solid?Cvapor equilibriums of PAHs were separately investigated in closed systems by headspace analysis.

Results and discussion

DDPB affects both liquid?Cvapor and solid?Cvapor processes of PAHs in soil. At DDPB concentrations below the critical micelle concentration (CMC), movement of PAHs from the bulk solution to the gas?Cliquid interface appeared to be facilitated by interaction between PAHs and the surfactant monomers adsorbed at the gas?Cliquid interface, promoting the volatilization of PAHs from solution. However, when DDPB was greater than the CMC, volatilization was inhibited due to the solubilization of PAHs by micelles. On the other hand, the formation of sorbed surfactant significantly inhibited the solid?Cvapor volatilization of PAHs.

Conclusions

The overall effect of the two simultaneous effects of DDPB on liquid?Cvapor and solid?Cvapor processes was a decreased volatilization loss of PAHs from soil. Inhibition of PAH volatilization was more significant for the soil with a lower moisture content.     

Determination of the organic aerosol mass to organic carbon ratio in IMPROVE samples

The ratio of organic mass (OM) to organic carbon (OC) in PM(2.5) aerosols at US national parks in the IMPROVE network was estimated experimentally from solvent extraction of sample filters and from the difference between PM(2.5) mass and chemical constituents other than OC (mass balance) in IMPROVE samples from 1988 to 2003. Archived IMPROVE filters from five IMPROVE sites were extracted with dichloromethane (DCM), acetone and water. The extract residues were weighed to determine OM and analyzed for OC by thermal optical reflectance (TOR). On average, successive extracts of DCM, acetone, and water contained 64%, 21%, and 15%, respectively, of the extractable OC, respectively. On average, the non-blank-corrected recovery of the OC initially measured in these samples by TOR was 115+/-42%. OM/OC ratios from the combined DCM and acetone extracts averaged 1.92 and ranged from 1.58 at Indian Gardens, AZ in the Grand Canyon to 2.58 at Mount Rainier, WA. The average OM/OC ratio determined by mass balance was 2.07 across the IMPROVE network. The sensitivity of this ratio to assumptions concerning sulfate neutralization, water uptake by hygroscopic species, soil mass, and nitrate volatilization were evaluated. These results suggest that the value of 1.4 for the OM/OC ratio commonly used for mass and light extinction reconstruction in IMPROVE is too low.     

Environmental implications of soil remediation using the Fenton process

This work evaluates some collateral effects caused by the application of the Fenton process to 1,1-bis(4-chlorophenyl)-2,2,2-trichloroethane (DDT) and diesel degradation in soil. While about 80% of the diesel and 75% of the DDT present in the soil were degraded in a slurry system, the dissolved organic carbon (DOC) in the slurry filtrate increased from 80 to 880mgl(-1) after 64h of reaction and the DDT concentration increased from 12 to 50microgl(-1). Experiments of diesel degradation conducted on silica evidenced that soluble compounds were also formed during diesel oxidation. Furthermore, significant increase in metal concentrations was also observed in the slurry filtrate after the Fenton treatment when compared to the control experiment leading to excessive concentrations of Cr, Ni, Cu and Mn according to the limits imposed for water. Moreover, 80% of the organic matter naturally present in the soil was degraded and a drastic volatilization of DDT and 2,2-bis(4-chlorophenyl)-1,1-dichloroethylene was observed. Despite the high percentages of diesel and DDT degradation in soil, the potential overall benefits of its application must be evaluated beforehand taking into account the metal and target compounds dissolution and the volatilization of contaminants when the process is applied.     

Modeling effects of moisture content and advection on odor causing vocs volatilization from stored swine manure

Abstract

Two models for evaluating the contents and advection of manure moisture on odor causing volatile organic compounds (VOC‐odor) volatilization from stored swine manure were studied for their ability to predict the volatilization rate (indoor air concentration) and cumulative exposure dose: a MJ‐I model and a MJ‐II model. Both models simulating depletion of source contaminant via volatilization and degradation based on an analytical model adapted from the behavior assessment model of Jury et al. In the MJ‐I model, manure moisture movement was negligible, whereas in the MJ‐II model, time‐dependent indoor air concentrations was a function of constant manure moisture contents and steady‐state moisture advection. Predicted indoor air concentrations and inhaled doses for the study VOC‐odors of p‐cresol, toluene, and p‐xylene varied by up to two to three orders of magnitude depending on the manure moisture conditions. The sensitivity analysis of both models suggests that when manure moisture movement exists, simply MJ‐I model is inherently not sufficient to represent a more generally volatilization process, which can even become stringent as moisture content increases. The conclusion illustrates how one needs to include a wide variety of manure moisture values in order to fully assess the complex volatilization mechanisms that are present in a real situation.     

The degradation of parathion and DDT in aqueous systems containing organic additives

Abstract

Laboratory studies were conducted to investigate some of the factors influencing pesticide degradation in‐ aqueous systems. Parathion added to natural water in ethanol, acetone or without organic solvent, was completely degraded within 2 wk. While most of the parathion was reduced to amino‐parathion when added in ethanol, no amino‐parathion was detected in the presence of acetone or when no solvent was added, suggesting that in the latter two cases the insecticide was aerobically degraded to other metabolites. No paraoxon was detected. When ethanol concentration was increased from 1% to 2 and 4%, the rate of parathion degradation was inversely related to the ethanol concentration. In the presence of glucose as a carbon source, approximately 50% of the parathion was reduced to aminoparathion. DDT degradation in natural water was more rapid when it was added in ethanol than when added in acetone. The only DDT metabolite detected was TDE, with about 36% conversion in presence of ethanol, and 20% when the DDT was added in acetone.     

Photocatalytic degradation of volatile organic compounds at the gas-solid interface of a TiO2 photocatalyst

In the present work, photocatalytic degradation of volatile organic compounds including gas-phase trichloroethylene (TCE), acetone, methanol and toluene over illuminated TiO2 was closely examined in a batch photoreactor as a function of water vapor, molecular oxygen and reaction temperature. Water vapor enhanced the photocatalytic degradation rate of toluene, but was inhibitive for acetone, and, there was an optimum water vapor concentration in the TCE and methanol removal. In a nitrogen atmosphere, it showed lower photocatalytic degradation rate than in air and pure oxygen. Thus, it could be concluded that oxygen is an essential component in photocatalytic reactions by trapping photogenerated electrons on the semiconductor surface and by decreasing the recombination of electrons and holes. As for the influence of reaction temperature, it was found that photocatalytic degradation was more effective at a moderate temperature than at an elevated temperature for each compound.     

PCB removal from contaminated dredged material

The purpose of this study was to evaluate the feasibility of decontaminating PCB contaminated sediment using land treatment technology. Five glass aquariums were set up to test the disappearance of polychlorinated biphenyls (PCBs) in dredged sediment under laboratory conditions that simulated photodegradation, biological transformation, and volatilization in dredged material confined disposal facilities (CDFs). A 40% decline in PCB concentration was achieved over a period of 5 months. Analysis of the variance in the data showed that periodic tilling produced a tangible effect on the disappearance of PCBs. However, the process or processes responsible for PCB disappearance could not be determined. PCB disappearance from the sediment was most likely caused by a combination of photolysis, volatilization, and biodegradation mechanisms rather than by any single process.