胶团强化超滤法(MEUF)去除废水中氯苯的研究

研究了3种单一表面活性剂十二烷基硫酸钠(SDS)、十六烷基三甲基溴化铵(CTMAB)、聚氧乙烯失水山梨脂肪酸酯醇醚(TW80)和混合表面活性剂TW80-SDS对氯苯(CB)的强化超滤,以期为有机废水胶团强化超滤技术提供参考。结果表明,进料液静置时间对去除率无显著影响,而振荡时间在1 h后对去除率影响不大。氯苯的去除率随进料液中表面活性剂浓度的增大而增大,单一的表面活性剂对氯苯的去除效果顺序为TW80CTMABSDS,且表面活性剂对氯苯的去除效果与表面活性剂的临界胶束浓度值(CMC)、亲水-亲油平衡值(HLB)呈负相关。阴-非混合表面活性剂TW80-SDS对氯苯的去除效果明显强于单一的SDS,且去除率随着非离子表面活性剂质量分数的增加而增加。渗透通量随着进料液中表面活性剂浓度的增加而下降,单一表面活性剂种类对渗透通量的影响顺序为SDSTW80CTMAB,混合表面活性剂中随着非离子表面活性剂质量分数的增加而渗透液的渗透通量越低。     

Solubility and adsorption behaviors of chlorpyriphos-methyl in the presence of surfactants

In the present work changes in the adsorption of the pesticide chlorpyrifos-methyl (CLP-m) on soil colloids induced by application of surfactants were determined using a batch equilibrium method. The surfactants used were sodium dodecyl sulphate (SDS), Tween 20, and dihexadecyldimethylammonium bromide (DHAB). The adsorption isotherms of CLP-m in aqueous medium and in surfactant solutions at concentration equal to the critical micelle concentration (CMC) fitted the Freunlich adsorption equation generally with R² values greater than 0.96. While the addition of SDS and DHAB decreased the pesticide adsorption, the addition of Tween 20 increased the pesticide adsorption. The increases or decreases in the adsorption in the experiment revealed that the behavior of CLP-m in soil water-systems mainly depends on the type of surfactant. Moreover water solubility of CLP-m changes by the three surfactants below and above their CMC were studied. While the solubility of CLP-m was enhanced by SDS both below and above the CMC, the solubility of the pesticide was enhanced by DHAB only above the CMC. Tween 20 did not influence the solubility of CLP-m.     

Effect of alum addition on the performance of submerged membranes for wastewater treatment.

The effect of aluminum sulfate (alum) addition on membrane performance was investigated, with a particular focus on membrane fouling. During initial operation, alum was added and the performance monitored. After terminating alum addition, the transmembrane pressure (TMP), which is indicative of membrane resistance to flow or fouling, increased. Accompanying the increase in TMP was an increase in the organic nonsettleable fraction (colloidal + dissolved) content of the mixed liquor and deterioration of permeate quality and floc strength. Permeate polysaccharide concentrations increased significantly, suggesting a preferential binding of solution polysaccharides by alum. Upon reinitiating alum addition, the TMP only partially recovered, indicating some irreversible fouling, while mixed liquor nonsettleable organic material, permeate quality, and floc strength returned to initial levels. These results suggest that direct alum addition to membrane bioreactors can improve membrane performance by reducing the organic fouling material and improving floc structure and strength. It appears that bulk liquid polysaccharides may contribute to irreversible membrane fouling, and this fraction can be efficiently controlled through the alum addition.     

Removal of arsenic from groundwater by micellar-enhanced ultrafiltration (MEUF)

The removal characteristics of arsenate using micellar-enhanced ultrafiltration (MEUF) were investigated. Among four different cationic surfactants used, hexadecylpyridinium chloride (CPC) showed the highest removal efficiency of arsenic (96%), and the removal efficiency with hexadecyltrimethylammonium bromide (CTAB) was 94%. But the removal efficiency with benzalkonium chloride (BC) was the lowest (57%) due to higher critical micelle concentration (CMC) of BC than those of other surfactants. Over 80% of arsenic was removed with octadecylamine acetate (ODA). On the effect of solution pH on the arsenic removal, since the valance of arsenate decreases from trivalent to monovalent as pH decreases, the removal was reduced at lower pH. The presence of 0.45mM of nitrate and 0.01mM of phosphate reduced the removal efficiency by 5-8%. This decrease was because of the competition between the arsenate, nitrate and phosphate for the binding sites of the surfactant micelle. Similar decrease in the removal of arsenate was observed with CPC, CTAB and ODA in the presence of these anions. In cross-flow filtration, the removal efficiency of arsenic was similar to that in the dead-end system. However, the decline in flux was less than that in dead-end filtration. In order to lower the concentration of the surfactant in the effluent, the effluent was treated with powdered activated carbon (PAC) before discharging to the environment. Over 98% surfactant was removed with 1gl(-1) of PAC. In conclusions, the MEUF is considered as a feasible process using CPC or CTAB to remove the arsenate from groundwater compared with the other solid based adsorbent processes.     

气-水联合反冲洗膜污染防治技术研究

采用气水联合反冲洗技术,考察了气水比(Qg/Ql)、反冲洗周期及其对膜污染的防治效果。结果表明,气水联合反冲洗较单独气或水反冲洗效果好;在过滤周期20min,反冲洗时间1min,气水比1.5时,气水联合反冲洗能够恢复膜通量到膜清水通量的80%以上。此法可大幅度清除沉积在膜表面的泥饼层,恢复膜通量,维持膜过滤性能的稳定,是一种较为有效的膜污染防治技术。     

Surfactant-induced mobilisation of trace metals from estuarine sediment: implications for contaminant bioaccessibility and remediation

The mobilisation of metals (Al, Fe, Cd, Cu, Mn, Ni, Pb, Sn, Zn) from contaminated estuarine sediment has been examined using commercially available surfactants. Metal release by the anionic surfactant, sodium dodecyl sulphate (SDS), increased with increasing amphiphile concentration up to and above its critical micelle concentration (CMC). Metal mobilisation by the bile acid salt, sodium taurocholate, and the nonionic surfactant, Triton X-100, however, did not vary with amphiphile concentration. SDS was the most efficient surfactant in mobilising metals from the sample, and Cd, Cu and Ni were released to the greatest extents (12-18% of total metal at [SDS] > CMC). Metal mobilisation appeared to proceed via complexation with anionic amphiphiles and denudation of hydrophobic host phases. Surfactants may play an important role in the solubilisation of metals in the digestive environment of deposit-feeding animals and, potentially, in the remediation of metal-contaminated soil and sediment.     

聚合物强化超滤处理含铜废水

聚合物强化超滤工艺（PEUF）是一种将高分子聚合物和超滤技术结合的新型、高效的重金属废水治理方法。以壳聚糖（CTS）为聚合物去除水中的铜离子。考察了吸附络合和超滤过程中影响铜去除率的多种因素。结果表明，溶液pH值为6.0、CTS浓度为0.15 g/L和反应时间为60 min时，通过超滤系统后效果最佳。装载比一定时，铜初始浓度的变化对铜的去除率没有明显影响。CTS对铜的吸附过程符合Langmuir吸附等温方程。还研究了超滤膜的污染情况和膜清洗方法，结果表明，酸清洗效果较好，可使膜通量恢复达87%左右。     

Micellar-enhanced ultrafiltration process (MEUF) for removing copper from synthetic wastewater containing ligands

The effects of the type and concentration of ligands on the removal of Cu by micellar-enhanced ultrafiltration (MEUF) with the help of either anionic or cationic surfactants were investigated. The removal efficiency of copper by anionic surfactant-(SDS-) MEUF depends on the ligand-to-Cu ratio and the ligand-to-Cu complexation constant. At fixed ligand-to-Cu ratio, the Cu removal efficiency decreases in the order of citric acid>NTA>EDTA, which is the reverse order of Cu-ligand complexation constants for these ligands. Increasing SDS-ligand ratios from 12 to 60 at fixed ligand concentration did not improve copper removal efficiency. The cationic surfactant, CPC, enhances Cu removal efficiency in systems with condition of ligand-copper ratios higher than 1.0, where Cu removal is not very efficient using SDS-MEUF process. The Cu removal efficiency with CPC-MEUF depends on both the ligand-to-Cu ratio and the type of ligands.     

Distribution of polycyclic aromatic hydrocarbons in soil-water system containing a nonionic surfactant

The effect of a nonionic surfactant, Triton X-100 (TX100), on the distribution of four representative polycyclic aromatic hydrocarbons (PAHs), phenanthrene, fluorene, acenaphthene and naphthalene, in soil-water system was studied on a natural soil. The apparent soil-water distribution coefficient with surfactant (Kd*) for these compounds increased when TX100 equilibrium concentration from zero to around the critical micelle concentration (CMC), followed by a decrease in Kd* at TX100 equilibrium concentration greater than CMC. This is a direct result of surfactant sorption onto soil followed by PAHs partitioning to the sorbed surfactant. The values of carbon-normalized solute distribution coefficient (Kss) with the sorbed TX100 are greater than the corresponding partition coefficients with soil organic matter (Koc), which indicates the soil-sorbed nonionic surfactant is more effective per unit mass as a partitioning medium than the native soil organic matter for PAHs. When Kd* = Kd the corresponding initial concentration of surfactant was defined as critical washing concentration (CWC). Depending on the surfactant initial concentration below or above the CWC, the addition of nonionic surfactant can enhance the retardation of soil for PAHs or promote the removal of PAHs from soil, respectively. The values of Kd* and CWC can be predicted by a model, which correlates them with the compounds' octanol-water partition coefficients (Kow), soil property and the amount of soil-sorbed surfactant.     

胶束强化超滤去除水中双酚A

采用截留分子量(MWCO)为5000 Dalton、1000 Dalton的聚砜超滤膜,MWCO为1 kDa的再生纤维素超滤膜;采用十二烷基苯磺酸钠(SDBS)、曲拉通100(TritonX-100)、吐温80(Tween-80)、烷基多苷(APG)为表面活性剂,用胶团强化超滤工艺去除水中双酚A。研究了不同材质和截留分子量的超滤膜、表面活性剂浓度、膜操作压力、溶液pH和溶液中电解质等因素对该工艺的影响。结果表明,SDBS对双酚A有较好的去除效果,去除率在80%以上。在H+和Na+存在的条件下,双酚A的截留率增加,透过液中SDBS浓度降低。SDBS与非离子表面活性剂的复配可以提高双酚A截留率,降低透过液中SDBS的浓度,复配效果优劣顺序为Tween-80TritonX-100APG。     

Effect of membrane type and material on performance of a submerged membrane bioreactor

This study evaluated the impact of membrane type and material on filtration performance in a submerged membrane bioreactor (MBR) for municipal wastewater treatment. Three types of microfiltration membranes with similar pore size of 0.1 microm but different materials and types, phase-inversed polytetrafluoroethylene (PTFE), track-etched polycarbonate (PCTE) and track-etched polyester (PETE), were used. Changes in permeability with time for the PCTE and PTFE membranes appeared similarly, whereas the PETE membrane exhibited the most rapid flux decline. Lower TOC in the permeate compared to the supernatant was probably due to a combination of biodegradation by the biofilm (cake layer) developed on the membrane surface and further filtration by cake layer and narrowed pores. The faster permeability decline and higher TOC removal rate of the PETE membrane were attributed to an initial permeate flux higher than an average design flux, which led to a faster rate of fouling and thicker cake layer. Therefore, an MBR should not be operated at a flux higher than the average design flux for a specific type of membrane. A gradual increment of biomass concentration did not significantly affect membrane permeability of each membrane investigated. Dissolved organic carbon fractionation results showed that the composition of each fraction between the supernatant and permeates did not change significantly with time, suggesting that membrane hydrophobicity was not a dominant factor affecting MBR fouling in this study. The organic foulants desorbed from the PCTE membrane contained approximately 60% of hydrophobic fraction, which was probably attributable to the extracellular polymeric substances proteins released from the biomass attached to the membrane. While the total filtration resistance of the PTFE membrane was influenced by a higher surface roughness, those of the PETE and PCTE membranes, which had a similar and lower roughness, were affected by the initial operating flux.     

Selective separation of copper(II) and nickel(II) from aqueous media using the complexation-ultrafiltration process

The polyethylenimine (PEI) as complexing agent was used to study the complexation-ultrafiltration (CP-UF) process in the selective removal of Cu(II) from Ni(II) contained in aqueous media. Preliminary tests showed that optimal chemical conditions for Cu(II) and Ni(II) complexation by the PEI polymer were pH>6.0 and 8.0, respectively, and polymer/metal weight ratio of 3.0 and 6.0, respectively. The effect of some important operating parameters on process selectivity was studied by performing UF tests at different parameters: pH, polymer/metal weight ratio, transmembrane pressure (TMP), and membrane cut-off in a batch experimental set-up. It was observed that process selectivity was achieved by choosing the pH value for obtaining a preferential copper complexation (pH 6.0), and the polymer/metal ratio needed to bound only the copper ion (3.0). The selective separation by UF tests was performed by using both a laboratory aqueous solution and a real aqueous effluent (water from Emoli torrent, Rende (CS)). The Iris 30 membrane at TMP of 200 kPa (2 bar) for both aqueous media gave the best results. A complete nickel recovery was reached, and copper recovery was the highest for this membrane (94% and 92%). Besides at this pressure, a lower water amount was needed to obtain total nickel recovery by diafiltration. A little higher membrane fouling was obtained by using the river effluent due to the presence of dissolved organic and inorganic matter.     

Removal of vaporous naphthalene using polyoxyethylenated nonionic surfactants

Previous research has demonstrated that an anionic surfactant can increase the solubility of the vapor phases of both naphthalene and sulfur dioxide in water. This study examines the feasibility of removing polycyclic aromatic hydrocarbons (PAHs) during gas absorption by adding the polyoxyethylenated nonionic surfactants tetraethylene glycol monodecyl ether (C10E4), octaethylene glycol monodecyl ether (C10E8), and octaethylene glycol monotetradecyl ether (C14E8), to water. The apparent solubility and absorption rates of naphthalene in surfactant solution were slightly higher than in pure water at a concentration lower than the critical micelle concentration (CMC). However, the apparent equilibrium naphthalene solubility increased linearly in proportion to the concentrations of nonionic surfactants because of the solubilization effect of micelles at concentrations above the CMC. The solubilization effect exceeded that of the reduced mass transfer coefficient, increasing the rate of absorption of vaporous naphthalene. For the four surfactants, the capacity to solubilize naphthalene was in the order C10E4 > C14E8 > C10E8 > sodium dodecyl sulfate (SDS) and was related to the hydrophile-lipophile balance values of the surfactants. The enrichment factors, which can express the degree of naphthalene solubility in solution, were 6.09-14.2 at a surfactant concentration of 0.01 M for the three polyoxyethylenated nonionic surfactants. Empirical findings confirm that adding nonionic surfactants increases the absorption efficiency of hydrophobic organic compounds (HOCs) using spray or packed tower.     

A/O和A2/O工艺对膜生物反应器处理焦化废水影响的研究

为提高膜生物反应器对焦化废水的处理效果，采用A/O和A²/O两种工艺的膜生物反应器处理焦化废水，通过对比处理效果、分析膜污染情况，寻求膜生物反应处理焦化废水的最优工艺。实验结果表明：A²/O工艺系统对酚、NH₃-N、COD的去除率分别为99%、90%和95%；A/O工艺系统对酚、NH₃-N和COD的去除率分别为97%、75%和93%。A²/O膜生物反应器系统对焦化废水中NH₃-N的去除效果明显优于A/O膜生物反应器系统，其反硝化率为50%～70%。对膜污染分析表明不同工艺对膜污染的影响不显著，A²/O工艺膜通量衰减59%，A/O工艺膜通量衰减56%。研究表明在膜生物反应器中，A²/O工艺对焦化废水的去除效果要优于A/O工艺。     

Parameters governing permeate flux in an anaerobic membrane bioreactor treating low-strength municipal wastewaters: a literature review.

The objective of this review was to conduct a comprehensive literature survey to identify the parameters that govern the permeate flux in an anaerobic membrane bioreactor (AnMBR) treating municipal wastewater. Based on the survey, research to date indicates that the optimal membrane system for an AnMBR consists of an organic, hydrophilic, and negatively charged membrane with a pore size of approximately 0.1 microm. The use of both external and submerged membrane configurations shows promise. The operating parameters that affect permeate flux in an external membrane system are transmembrane pressure (TMP) and cross-flow velocity. The operating parameters that affect permeate flux in a submerged membrane system are TMP, sparging intensity, and duration of the relaxation period. Both cross-flow velocity and sparging intensity impart a significant amount of shear force on the biomass in an AnMBR. High shear forces can reduce the microbial activity in an AnMBR. In addition, high shear forces can reduce the size of the biosolids in the mixed liquor and increase the release of soluble microbial products. In this respect, external and submerged membrane systems are expected to perform differently because the magnitude of the shear forces to which the biomass is exposed in an external membrane system is significantly greater than that in a submerged system. The size of the biosolid particles and concentration of soluble microbial products in the mixed liquor affect permeate flux. Higher concentrations of soluble microbial products may be present in the mixed liquor when an AnMBR is operated at relatively low operating temperatures. Aerobic polishing following anaerobic treatment can potentially significantly reduce the concentration of some components of the soluble microbial products in the mixed liquor. It is not possible to remove the foulant layer on an organic membrane with caustic cleaning alone. Acidic cleaning or acidic cleaning followed by caustic cleaning is required to remove the foulant layer. This suggests that both biological/organic and inorganic material contribute to membrane fouling.     

表面活性剂改性活性炭对阳离子染料的吸附

以阴离子表面活性剂十二烷基硫酸钠(SDS)为改性剂对粉末活性炭(AC)改性,研究了SDS在活性炭表面的吸附稳定性,用比表面积测定仪、Zeta电位测定仪对改性前后活性炭进行表征,并将其用于吸附模拟废水中的阳离子染料。结果表明,改性剂SDS浓度等于临界胶束浓度时,改性后活性炭(SDS-AC)对SDS吸附稳定,SDS在纯水和染料溶液中的解吸率分别为19.4%和1.6%。pH对活性炭吸附阳离子橙染料影响较小,SDS-AC和AC对染料的吸附平衡时间分别为4 h和12 h,SDS-AC和AC对阳离子橙染料的吸附动力学模型符合拟二级反应模型,吸附等温线更符合Langmuir吸附等温方程,SDS-AC对阳离子橙染料的最大吸附量较AC提高47.8%,SDS-AC对阳离子橙染料的吸附机制为物理吸附和化学吸附共同作用下的单分子层吸附,其中化学吸附是主要控速步骤。     

SDS改性沸石吸附结晶紫简

以表面活性剂十二烷基硫酸钠（SDS）对沸石进行改性，改性后的沸石对结晶紫溶液进行吸附，以紫外可见分光光度计分析最佳吸附条件。实验结果表明，在30℃，SDS改性沸石投入量为0.25 g；吸附平衡时间为1 h；pH为8的条件下，对含50 mg/L结晶紫染料的去除率可达到92.6%，吸附量达到4.63 mg/g。SDS改性沸石吸附结晶紫的等温吸附曲线与Henry型和Freundlich型均拟合较好。热力学参数计算结果表明，吸附符合自发吸热过程。     

Use of chemical coagulants to control fouling potential for wastewater membrane bioreactor processes.

Chemical coagulation with ferric chloride, alum, and an organic polymer were used to control the fouling potential of mixed liquors for submerged membrane bioreactor (MBR) processes in treating municipal wastewater. Their filterability was evaluated using a submerged hollow fiber ultrafiltration apparatus operated in constant permeate flux mode. The collected transmembrane pressures over filtration time were used to calculate the membrane fouling rates. The results showed that coagulation pretreatment can reduce fouling rates when MBRs were operated above the critical flux. Even though coagulation with the organic polymer formed larger mixed liquor suspended solids particles and had shorter time-to-filtration than those with ferric chloride and alum, the filterability for membrane filtration were similar, indicating that the membrane fouling in MBR systems was mainly controlled by the concentration of smaller colloidal particles.     

Enhanced naphthalene solubility in the presence of sodium dodecyl sulfate: effect of critical micelle concentration

Surfactants can increase the solubility of non-polar compounds, and have been applied in areas such as soil washing and treatment of non-aqueous phase liquids (NAPLs). This investigation explored the feasibility of removing vapor phase polycyclic aromatic hydrocarbon (PAH) from gases using an anionic surfactant. The solubility of vapor phase naphthalene was measured herein using gas chromatograph (GC) with a photon ionization detector (PID). The measurement results indicated that surfactant molecules were not favorable to micelle formation when temperatures increased from 25 degrees C to 50 degrees C. Regardless of whether solutions were quiescent or agitated, equilibrium naphthalene apparent solubility increased linearly with surfactant concentrations exceeding critical micelle concentration (CMC). The pH effects on naphthalene apparent solubility were small. Agitation increased naphthalene apparent solubility and lumped mass transfer coefficients. Furthermore, lumped mass transfer coefficients decreased with increasing surfactant concentration owing to increase in interfacial resistance and viscosity and decreased spherical micelle diffusion coefficients. Finally, the net absorption rate increased because the solubilization effects of micelles exceeded the reduction effects of mass transfer coefficient above the CMC. The enhanced naphthalene apparent solubility from the addition of surfactant can be expressed by an enrichment factor (EF). The EF value of naphthalene for the surfactant solution at 0.1 M with agitation at 270 rpm relative to quiescent water could reach 18.6. This work confirms that anionic surfactant can improve the removal efficiency of hydrophobic organic compound (HOC) from the gas phase.     

膜蒸馏处理糖精钠生产废水

采用直接接触式膜蒸馏(DCMD)工艺处理糖精钠生产废水。分析了经过活性炭吸附预处理前后,膜蒸馏连续循环运行的效果。实验结果表明,未经预处理的废水在膜蒸馏过程中,废水中所含有机物不仅导致膜材料的润湿,引起产水电导率升高及膜孔润湿,促进盐晶体在膜表面附着,使产水通量下降。经吸附预处理后,膜蒸馏过程中产水通量介于10.40～11.24 kg/(m2.h)。吸附预处理能有效减缓产水通量的衰减,提高产水水质。废水经过活性炭预处理后进行膜蒸馏浓缩处理,当浓缩倍数达到5倍时,通量保持在10.55 kg/(m2.h)左右;产水水质稳定,截留率在99.5%以上。研究结果表明,吸附-膜蒸馏工艺可以应用于糖精钠生产废水的回用处理,有明显的应用前景。