交换电极法强化电动修复铬污染土壤

pH值是影响污染土壤电动修复的主要因素。为此提出了交换电极法强化电动修复,并对该技术进行了实验研究。实验土壤Cr污染浓度为506.36 mg/kg,工作电压为1 V/cm,结果显示,固定电极方向运行模式下,运行2 d,产生聚焦效应,运行8 d,碱性区Cr(III)残留量和酸性区Cr(VI)残留量较大,分别是97.88 mg/kg和328 mg/kg,总铬去除率为59.04%。采用交换电极法,交换频率为4 d,运行8 d,总铬去除率为70.18%;交换频率为2 d,运行8 d,总铬去除率高达86.10%,土壤中总铬平均含量从506.36 mg/kg降至73.56 mg/kg,达到酸性土壤环境质量一级标准。该技术可控制土壤pH值在中性范围,电流密度高,不添加化学试剂,操作简单。     

Electro-migration of heavy metals in an aged electroplating contaminated soil affected by the coexisting hexavalent chromium

Cr(VI) was often reported to oxidize soil organic matter at acidic environments due to its high ORP, probably thus changing cationic metal species bound to soil organic matter, and influencing their electro-migration patterns. However, such an effect on the electro-migration was not confirmed in most previous studies. Therefore, this study applied a fixed voltage direct current field on an aged electroplating contaminated clayed soil, with a special interest in the direct or indirect influence of Cr(VI) on the electro-migration of other coexisting metals. After 353 h electrokinetic process, 81% of Zn, 53% of Ni and 22% of Cu in the original soil were electro-migrated into the electrolyte, and most of the remaining concentrated near the cathode. The Cr(VI) oxidized some soil organic matter along its migration pathway, with a pronounced reaction occurred near the anode at low pHs. The resulting Cr(III) reversed its original movement, and migrated towards the cathode, leading to the occurrence of a second Cr concentration peak in the soil. Metal species analyses showed that the amount of metals bound to soil organic matter significantly decreased, while a substantial increase in the Cr species bound to Fe/Mn (hydro-)oxides was observed, suggesting an enhancement of cationic metal electro-migration by the reduction of Cr(VI) into Cr(III). However, the Cr(VI) may form some stable lead chromate precipitates, and in turn demobilize Pb in the soil, as the results showed a low Pb removal and an increase in its acid-extractable and residual fractions after electrokinetic remediation.     

In situ remediation of soils contaminated with toxic metal ions using microwave energy

Following onto our work on the in situ remediation of soils contaminated with PAH's, PCB's and other polychlorinated organic compounds using microwave energy, we now report a preliminary investigation on the in situ remediation of soils contaminated with toxic metal ions: Cd(II), Mn(II), Th(IV), Cr(III) and mainly Cr(VI). The soil is partially vitrified in the process, and extraction with hot (70 degrees C) 35% nitric acid for 4.5 h leads to the recovery of very small amounts of the metals which had been spiked into the clean soil: Cd, Mn, and Cr(III) are completely immobilized (unextractable), Th is mostly unextractable, and Cr(VI) partially extractable at very high levels of spiking, but almost completely unextractable using the US EPA Toxicity Characteristic Leaching Procedure. This suggests that contaminated soils which are not going to be used for agricultural purposes can be remediated safely to preset depths without fear of the toxic metal ions leaching out for a long time.     

Effect of pH control at the anode for the electrokinetic removal of phenanthrene from kaolin soil

Polycyclic aromatic hydrocarbon (PAH)-contaminated soils exist at numerous sites, and these sites may threaten public health and the environment because many PAH compounds are toxic, mutagenic, and/or carcinogenic. PAHs are also hydrophobic and persistent, so conventional remediation methods are often costly or inefficient, especially when the contaminants are present in low permeability and/or organic soils. An innovative technique, electrokinetically enhanced in situ flushing, has the potential to increase soil-solution-contaminant interaction and PAH removal efficiency for low permeability soils; however, the electrolysis reaction at the anode may adversely affect the remediation of low acid buffering capacity soils, such as kaolin. Therefore, the objective of this study was to improve the remediation of low acid buffering soils by controlling the pH at the anode to counteract the electrolysis reaction. Six bench-scale electrokinetic experiments were conducted, where each test employed one of three different flushing solutions, deionized water, a surfactant, or a cosolvent. For each of these solutions, tests were performed with and without a 0.01 M NaOH solution at the anode to control the pH. The test using deionized water with pH control generated a higher electroosmotic flow than the equivalent test performed without pH control, but the electroosmotic flow difference between the surfactant and cosolvent tests with and without pH control was minor compared to that observed with the deionized water tests. Controlling the pH was beneficial for increasing contaminant solubilization and migration from the soil region adjacent to the anode, but the high contaminant concentrations that resulted in the middle or cathode soil regions indicates that subsequent changes in the soil and/or solution chemistry caused contaminant deposition and low overall contaminant removal efficiency.     

Reduction of Cr(VI) by malic acid in aqueous Fe-rich soil suspensions

Detoxification of Cr(VI) through reduction by organic reductants has been regarded as an effective way for remediation of Cr(VI)-polluted soils. However, such remediation strategy would be limited in practical applications due to the low Cr(VI) reduction rate. In this study, the catalytic effect of two Fe-rich soils (Ultisol and Oxisol) on Cr(VI) reduction by malic acid was evaluated. As the results shown, the two soils could obviously accelerate the reduction of Cr(VI) by malic acid at low pH conditions, while such catalytic effect was gradually suppressed as the increase in pH. After reaction for 48 h at pH 3.2, Oxalic acid was found in the supernatant of Ultisol, suggesting the oxidization of hydroxyl in malic acid to carboxyl and breakage of the bond between C₂ and C₃. It was also found that the catalytic reactivity of Ultisol was more significant than that of Oxisol, which could be partly attributed to the fact that the amount of Fe(II) released from the reductive dissolution of Ultisol by malic acid was larger than that of Oxisol. With addition of Al(III), the catalytic effect from Ultisol was inhibited across the pH range examined. On the contrary, the presence of Cu(II) would increase the catalytic effect of Ultisol, which was more pronounced with the increase in pH. This study proposed a potential way for elimination of the environmental risks posed by the Cr(VI) contamination by use of the natural soil surfaces to catalyze Cr(VI) reduction by the organic reductant such as malic acid, a kind of organic reductant originating from soil organic decomposition process or plant excretion.     

A two-stage process using electrokinetic remediation and electrochemical degradation for treating benzo[a]pyrene spiked kaolin

An innovative process that combines soil electrokinetic remediation and liquid electrochemical oxidation for the degradation of organic compounds present in a polluted soil was developed and evaluated by using benzo[a]pyrene spiked kaolin. In order to increase benzo[a]pyrene solubility during electrokinetic treatment, the addition of a co-solvent or surfactant, such as ethanol or Brij 35, as flushing solution was tested. The research carried out demonstrated the influence of the desorption agent employed on benzo[a]pyrene remediation from the kaolin matrix. Thus, if the flushing solution was ethanol at 40%, there was no presence of contaminant in either chamber. On the contrary, when a solution of surfactant Brij 35 was used, benzo[a]pyrene was transported towards the cathode chamber, where it was collected. Moreover, the extent of this recovery depends on the pH profile on the soil. When no pH control was used, around 17% of initial contaminant was detected in the cathode chamber; however, when pH control was applied, the recovery of benzo[a]pyrene could be higher than 76%, when the pH control in the anode chamber was set at 7.0.In order to obtain the total degradation of mobilised benzo[a]pyrene from the contaminated soil, the liquid collected by electrokinetic remediation was oxidised by electrochemical treatment. This oxidation was accomplished via an electrochemical cell with a working volume of 0.4 L, and graphite as electrode material. The benzo[a]pyrene was almost totally degraded in 1 d, reaching a degradation of about 73% in 16 h.     

Multispecies transport of metal–EDTA complexes and chromate through undisturbed columns of weathered fractured saprolite

Laboratory-scale tracer experiments were conducted to investigate the geochemical and hydrological processes that govern the fate and transport of organically chelated radionuclides and toxic metals in undisturbed saturated columns of weathered, fractured shale saprolite. Three long-term, reactive contaminant injections were pulsed onto three separate soil columns, with the following influent mixtures: (1) ¹⁰⁹CdEDTA²⁻, (2) ¹⁰⁹CdEDTA²⁻ and ^57,58Co(II)EDTA²⁻, and (3) ¹⁰⁹CdEDTA²⁻, ⁵⁷Co(III)EDTA⁻, and H⁵¹CrO₄⁻. Both single and multiple species experiments were conducted to determine the importance of interaction between the contaminants and competition for surface sites. Flow interruption was used to identify physical and chemical non-equilibrium (PNE and CNE) which were caused by multiple pore-region flow and rate-limited chemical reactions, respectively. Reactive contaminant transport through the fractured, weathered shale was affected by sorption, redox, and dissociation reactions, which were mediated by soil organic matter and surficial oxides of Fe, Mn, and Al. The transport of CdEDTA²⁻ was significantly influenced by ligand-promoted dissolution of subsurface Fe and Al sources, resulting in the liberation of Cd²⁺, Al(III)EDTA⁻ and Fe(III)EDTA⁻. Flow interruption confirmed that the surface-mediated dissociation reaction was time-dependent, with the stability of the CdEDTA²⁻ complex dependent on its residence time within the soil. The migration of Co(II)EDTA²⁻ was dominated by oxidization to the highly stable Co(III)EDTA⁻ species, and elevated effluent Mn²⁺ suggested that surficial Mn(IV) oxides likely catalyzed the redox reaction, though Fe-oxides may have also contributed to the reaction. Dissociation (12%) of the Co(II)EDTA²⁻ complex was first observed during flow interruption, indicating that rate-limited dissociation of the complex by Fe-oxides may be significant under equilibrium conditions. The transport of HCrO₄⁻ was significantly altered by the reduction of mobile Cr(VI) to irreversibly bound Cr(III). The reduction reaction was catalyzed by surface-bound natural organic matter and flow interruption confirmed that the reaction was time-dependent. There was little evidence of competitive effects between the various contaminants in the multispecies experiments, since each was influenced by a different geochemical process during transport through the soil. The results of this study further support research findings that suggest anionic toxic metals and radionuclide–organic complexes can be significantly influenced by soil geochemical processes that can both enhance and impede the subsurface migration of these contaminants.     

Distribution, origin and fate of chromium in soils in Guanajuato, Mexico

Total, hexavalent and trivalent chromium were determined in surface and 30-cm depth soil samples from a highly chromium-polluted area in Guanajuato state, central México. Four samples were also analyzed by a sequential extraction procedure. Nearly 0.9 km(2) out of the 8 km(2) area sampled was polluted with chromium, at concentrations up to 12960 mg kg(-1), mostly as Cr(III). Concentrations of Cr(VI) were lower than 0.5 mg kg(-1) in most sampled points, with the exception of one, where the concentration was found to be 65.14 mg kg(-1). Chromiumcontaining dust from a chromate factory accounted for most of the contamination. The highest concentrations of hexavalent chromium in soil, were in the bottom sediments of an abandoned water reservoir used to store polluted water from a well, before use of the water in the factory process. Tannery wastes, dust from a sanitary landfill of chromate compounds and the transport of chromium products are the sources of chromium at other sites. Chromium is fixed preferentially in the hydrous Fe and Mn oxides in the more polluted soils. Less polluted soils have a high proportion of chromium associated with the sulfide and organic fraction. Cr(III) is retained preferentially in the superficial soil layer. Variations in the physical characteristics of the soil, relative abundance of the various soil components and characteristics of the contaminant source, give rise to differences in chromium soil concentrations with depth.     

Terrestrial ecotoxicity and effect factors of metals in life cycle assessment (LCA)

Life cycle impact assessment aims to translate the amounts of substance emitted during the life cycle of a product into a potential impact on the environment, which includes terrestrial ecosystems. This work suggests some possible improvements in assessing the toxicity of metals on soil ecosystems in life cycle assessment (LCA). The current available data on soil ecotoxicity allow one to calculate the chronic terrestrial HC50(EC50) (hazardous concentration affecting 50% of the species at their EC50 level, i.e. the level where 50% of the individuals of the species are affected) of nine metals and metalloids (As(III) or (V), Be(II), Cr(III) or (VI), Sb(III) or (V), Pb(II), Cu(II), Zn(II) and Ni(II)). Contrarily to what is generally advised in LCIA, the terrestrial HC50 of metals shall not be extrapolated from the aquatic HC50, using the Equilibrium Partitioning method since the partition coefficient (K(d)) of metals is highly variable. The experimental ecotoxicology generally uses metallic salts to contaminate artificial soils but the comparison of the EC50 or NOEC obtained for the same metal with different salts reveals that the kind of salt used insignificantly influences these values. In contrast, depending on the metallic fraction of concern, the EC50 may vary, as for cadmium: the EC50 of Folsomia candida, expressed as free Cd in pore water is almost 2.5 orders of magnitude lower than that expressed as total metal. A similar result is obtained with Eisenia fetida, confirming the importance of metals speciation in assessing their impact on soils. By ranking the metals according to the difference between their terrestrial and aquatic HC50 values, two groups are distinguished, which match the hard soft acids and bases (HSAB) concept. This allows to estimate their affinity for soil components and potential toxicity according to their chemical characteristics.     

Spectroscopic investigation of magnetite surface for the reduction of hexavalent chromium

The reduction of Cr(VI) to Cr(III) by magnetite in the presence of added Fe(II) was characterized through batch kinetic experiments and the effect of Fe(II) addition and pH were investigated in this study. The addition of Fe(II) into magnetite suspension improved the reductive capacity of magnetite. Eighty percent of Cr(VI) was reduced by magnetite (6.5 g l(-1)) with Fe(II) (80 mg l(-1)) within 1 h, while 60% of Cr(VI) was removed by magnetite only. However, the extent of improved reductive capacity of magnetite with Fe(II) was less than that predicted by the summation of each reduction capacity of magnetite and Fe(II). The reduction of Cr(VI) in the magnetite suspension with Fe(II) increased with the increase of molar ratio of Fe(II) to Cr(VI) (0.6, 1, 1.5, 2.3) in the range of 0-2.3 and with the decrease of pH in the range of pH 8.0-5.5. The speciation of chromium, iron, and oxygen on the surface of magnetite was investigated by X-ray photoelectron spectroscopy. Cr 2p3/2, Fe 2p3/2, and O 1s peaks were mainly observed at 576.7 and 577.8 eV, at 711.2 eV, and at 530.2 and 531.4 eV, respectively. The results indicates that Cr(III) and Fe(III) were the dominant species on the surface of magnetite after reaction and that the dominant species covered the magnetite surface and formed metal (oxy)hydroxide.     

Remediation of chromium-contaminated soil by electrokinetics and electrokinetics coupled with CaAl-LDH permeable reaction barrier

Environmental Science and Pollution Research - The remediation of Cr(VI)-contaminated soil was investigated by electrokinetic (EK) and permeable-reactive-barrier assisted electrokinetic (EK-PRB)....     

Removal of hexavalent chromium of contaminated soil by coupling electrokinetic remediation and permeable reactive biobarriers

Purpose

In this study, a novel and ecological alternative have been developed to treat soils contaminated with hexavalent chromium coupling two well-known systems: electrokinetic remediation and permeable reactive biobarriers. The electric field promotes the electromigration of the hexavalent chromium oxyanions towards the anode. The biobarriers were placed before the anode electrode, in order to promote the reduction and retention of the chromium migrating in its direction. Thus, this technology provided a global treatment to soil removal without subsequent treatments of the contaminated effluents.

Methods

The electrokinetic system was coupled with two different permeable reactive biobarriers composed by Arthrobacter viscosus bacteria, supported either in activated carbon or zeolite. An electric field of 10?V was applied and two different treatment times of 9 and 18?days were tested.

Results

Removal values of 60% and 79% were obtained when electrokinetic treatment was coupled with zeolite and activated carbon biobarriers, respectively, for a test period of 18?day. The reduction of hexavalent chromium to trivalent chromium was around 45% for both systems.

Conclusions

In this work, two types of biobarriers were efficiently coupled to electrokinetic treatment to decontaminate soil with Cr(VI). Furthermore, the viability of the new coupling technology developed (electrokinetic?+?biobarriers) to treat low-permeability polluted soils was demonstrated.     

Reduction of hexavalent chromium by ascorbic acid in aqueous solutions

Hexavalent chromium is a priority pollutant in the USA and many other countries. Reduction of Cr(VI) to Cr(III) is environmentally favorable as the latter species is not toxic to most living organisms and also has a low mobility and bioavailability. Reduction of Cr(VI) by ascorbic acid (vitamin C) as a reductant was studied using potassium dichromate solution as the model pollutant. Effects of concentration of vitamin C, pH, temperature, irradiation and reaction time on the reduction of Cr(VI) were examined. Cr(VI) might be reduced by vitamin C not only in acidic conditions but also in weakly alkaline solutions. The reduction of Cr(VI) by vitamin C might occur not only under irradiation but also in the dark. Vitamin C is an important biological reductant in humans and animals, and not toxic. It is water-soluble and can easily permeate through various types of soils. The results indicate that vitamin C could be used in effective remediation of Cr(VI)-contaminated soils and groundwater in a wide range of pH, with or without sunlight.     

Column study of Cr(VI) removal by cationic hydrogel for in-situ remediation of contaminated groundwater and soil

Column experiments were conducted for examining the effectiveness of the cationic hydrogel on Cr(VI) removal from groundwater and soil. For in-situ groundwater remediation, the effects of background anions, humic acid (HA) and pH were studied. Cr(VI) has a higher preference for being adsorbed onto the cationic hydrogel than sulphate, bicarbonate ions and HA. However, the adsorbed HA reduced the Cr(VI) removal capacity of the cationic hydrogel, especially after regeneration of the adsorbents, probably due to the blockage of adsorption sites. The Cr(VI) removal was slightly influenced by the groundwater pH that could be attributed to Cr(VI) speciation. The 6-cycle regeneration and reusability study shows that the effectiveness of the cationic hydrogel remained almost unchanged. On average, 93% of the adsorbed Cr(VI) was recovered in each cycle and concentrated Cr(VI) solution was obtained after regeneration. For in-situ soil remediation, the flushing water pH had an insignificant effect on the release of Cr(VI) from the soils. Multiple-pulse flushing increased the removal of Cr(VI) from the soils. In contrast, more flushing water and longer operation may be required to achieve the same removal level by continuous flushing.     

Mobility and recalcitrance of organo-chromium(III) complexes

Hexavalent chromium [Cr(VI)] is a major industrial pollutant. Bioremediation of Cr(VI) to Cr(III) is a viable clean-up approach. However, Cr(VI) bioreduction also produces soluble organo–Cr(III) complexes, and little is known about their behavior in the environment. When tested with soil columns, citrate–Cr(III) showed little sorption to soil; malate–Cr(III) had limited partitioning with soil; and histidine–Cr(III) exhibited significant interaction with soil. It appears that the mobility varies depending on the organic ligand. Further, Ralstonia eutropha JMP 134 and Pseudomonas aeruginosa pAO1 readily degraded malate, citrate, and histidine, but not the corresponding organo–Cr(III) complexes. The recalcitrance is not due to toxicity, but the complexes are likely to cause hindrance to enzymes, as malate dehydrogenase and amino acid oxidase could not use malate–Cr(III) and histidine–Cr(III), respectively. The data are in agreement with the reports of soluble organo–Cr(III) complexes in the environment.     

XANES study of Cr sorbed by a kitchen waste compost from water

A kitchen waste compost was used to sorb Cr for various times from water containing either Cr(NO3)3 or CrO3 in different concentrations. Scanning electron microscopy (SEM) results show that the composts have been partially oxidized by Cr(VI) during the sorption experiments. X-ray absorption near edge structure (XANES) simulation suggests that about 54.1-61.0% Cr sorbed on the compost is in form of organic Cr(III) through ionic exchange process with the rest being existent as Cr(NO3)3 in the Cr(III) sorption case; no Cr(OH)3 is observed or expected because the solution pH after sorption experiments is or= 5.94. Moreover, organic Cr(III) represents about 51.7-69.0% of the total sorbed Cr, and the rest (6.1-28.5%) is Cr(VI).     

Chromium accumulation by the hyperaccumulator plant Leersia hexandra Swartz

Leersia hexandra Swartz (Gramineae), which occurs in Southern China, has been found to be a new chromium hyperaccumulator by means of field survey and pot-culture experiment. The field survey showed that this species had an extraordinary accumulation capacity for chromium. The maximum Cr concentration in the dry leaf matter was 2978 mg kg(-1) on the side of a pond near an electroplating factory. The average concentration of chromium in the leaves was 18.86 times as that in the pond sediment, and 297.41 times as that in the pond water. Under conditions of the nutrient solution culture, it was found that L. hexandra had a high tolerance and accumulation capacity to Cr(III) and Cr(VI). Under 60 mg l(-1) Cr(III) and 10 mg l(-1) Cr(VI) treatment, there was no significant decrease of biomass in the leaves of L. hexandra (p>0.05). The highest bioaccumulation coefficients of the leaves for Cr(III) and Cr(VI) were 486.8 and 72.1, respectively. However, L. hexandra had a higher accumulation capacity for Cr(III) than for Cr(VI). At the Cr(III) concentration of 10 mg l(-1) in the culture solution, the concentration of chromium in leaves was 4868 mg kg(-1), while at the same Cr(VI) concentration, the concentration of chromium in leaves was only 597 mg kg(-1). These results confirmed that L. hexandra is a chromium hyperaccumulator which grows rapidly with a great tolerance to Cr and broad ecological amplitude. This species could provide a new plant resource that explores the mechanism of Cr hyperaccumulation, and has potential for usage in the phytoremediation of Cr-contaminated soil and water.     

Arsenic and chromium speciation in an urban contaminated soil

The distribution and speciation of As and Cr in a contaminated soil were studied by synchrotron-based X-ray microfluorescence (μ-XRF), microfocused X-ray absorption spectroscopy (μ-XAS), and bulk extended X-ray absorption fine structure spectroscopy (EXAFS). The soil was taken from a park in Wilmington, DE, which had been an important center for the leather tanning industry along the Atlantic seaboard of the United States, until the early 20th century. Soil concentrations of As, Cr, and Pb measured at certain locations in the park greatly exceeded the background levels of these heavy metals in the State of Delaware. Results show that Cr(III) and As(V) species are mainly present in the soil, with insignificant amounts of Cr(VI) and As(III). Micro-XRF maps show that Cr and Fe are distributed together in regions where their concentrations are diffuse, and at local spots where their concentrations are high. Iron oxides, which can reduce Cr(VI) to Cr(III), are present at some of these hot spots where Cr and Fe are highly concentrated. Arsenic is mainly associated with Al in the soil, and to a minor extent with Fe. Arsenate may be sorbed to aluminum oxides, which might have transformed after a long period of time into an As-Al precipitate phase, having a structure and chemical composition similar to mansfieldite (AlAsO(4)?2H(2)O). The latter hypothesis is supported by the fact that only a small amount of As present in the soil was desorbed using the characteristic toxicity leaching procedure tests. This suggests that As is immobilized in the soil.     

A study on the Cr(VI) removal from aqueous solutions by steel wool

The reduction of Cr(VI) by steel wool and the precipitation of reduced chromium by CaCO(3) powder and NaOH solution were investigated in continuous and batch systems, respectively. The effects of acid and initial Cr(VI) concentrations, volumetric rate and temperature of solution on Cr(VI) reduction were studied. The results showed that the reduction of Cr(VI), to a large extent, depended on, and increased with, acid concentration. The Cr(III) and iron ions in the reduced solution were completely precipitated by using NaOH solution at appropriate alkaline conditions. It was concluded that CaCO(3) powder could be used as a cheap precipitant for Cr(III) ions. But the iron ions in the reduced solution could not be fully removed by using this precipitant.     

Comparative and competitive adsorption of Cr(VI), As(III), and Ni(II) onto coconut charcoal

This study evaluates the behavior of coconut charcoal (AC) to adsorb Cr(VI), As(III), and Ni(II) in mono- and multicomponent (binary and ternary) systems. Batch experiments were carried out for mono- and multicomponent systems with varying metal ion concentrations to investigate the competitive adsorption characteristics. The adsorption kinetics followed the mechanism of the pseudo-second-order equation in both single and binary systems, indicating chemical sorption as the rate-limiting step of adsorption mechanism. Equilibrium studies showed that the adsorption of Cr(VI), As(III), and Ni(II) followed the Langmuir model and maximum adsorption capacities were found to be 5.257, 0.042, and 1.748 mg/g, respectively. In multicomponent system, As(III) and Ni(II) adsorption competed intensely, while Cr(VI) adsorption was much less affected by competition than As(III) and Ni(II). With the presence of Cr(VI), the adsorption capacities of As(III) and Ni(II) on AC were higher than those in single system and the metal sorption followed the order of Ni(II)?>?As(III)?>?Cr(VI). The results from the sequential adsorption–desorption cycles showed that AC adsorbent held good desorption and reusability.