Pretreatment of municipal solid waste prior to landfilling

An outdoor pilot-scale study was undertaken to pretreat municipal solid waste by windrow composting. The raw waste was introduced to active composting without any source separation or pulverization. Pretreatment indicators were developed and used as a tool to measure the optimum level of sorting and waste stabilization. The moisture content of the waste dropped from 68% to 61% and the pile attained a thermophilic temperature in one week. It was observed that the C/N ratio, pH profile and temperature gradients were comparable to that of traditional windrow composting. Within one week of active bulk composting, the easily degradable organic matter was consumed and there was a significant reduction in the bulk volume of the mixed waste. The pre-composted wastes were then sorted into four fractions. Compared to the initial untreated waste, the pretreated waste showed greater sorting efficiency and reduced volatile solids. A 1-m³ cage was used to study pile settlement and volume reduction. The results indicate that pretreatment by bulk composting could reduce by ≈40% the total mass of waste hauled to landfill sites in developing countries.     

Effect of horticultural waste composting on infected plant residues with pathogenic bacteria and fungi: integrated and localized sanitation

The aim of this work was to study the effect of composting on the viability of plant pathogenic fungi and bacteria. The research consisted of pilot-scale composting of horticultural waste in compost windrows. Studies were carried out on vegetable residues infected with plant pathogenic microorganisms included by either integrated or localized infection. In the first case, the plant pathogen viability was investigated when infected material was mixed throughout compost, while the localized infection was used to study the effect of the composting process on plant waste spot-inoculated with pathogenic microorganisms. Results for localized sanitation showed the total elimination of all tested phytopathogens between 48 and 120 h after composting began. In this case significant differences were observed in relation to 9 different zones in the pile. The disappearance of these microorganisms was similar when all plant waste included in the windrow was infected (integrated infection). Additionally, the results obtained confirmed that the bacteria showed a greater capacity to persist during composting than the fungi. Composting is therefore considered a useful method for recycling horticultural waste and eliminating phytopathogenic bacteria and fungi that inhabit this kind of residue.     

Swine manure composting by means of experimental turning equipment

The purpose of research was to test the effectiveness of a prototype of a turning machine and to evaluate the feasability of a farm-scale composting process of the solid fraction of swine manure. A qualitative evaluation of the process and final product was made by monitoring the following parameters: process temperature, oxygen concentration inside the biomass, gaseous emissions (CH4, CO2, NH3, N2O), respiration index, humification index, total and volatile solids, carbon and nitrogen, pH and microbial load. The prototype proved to be very effective from a technical-operational point of view. The composting process exhibited a typical time-history, characterised by a thermophilic phase followed by a curing phase [Chiumenti, A., Chiumenti, R., Diaz, L.F., Savage, G.M., Eggerth, L.L., Goldstein, N., 2005. Modern Composting Technologies. BioCycle-JG Press, Emmaus, PA, USA]. Gas emissions from compost the windrow were more intense during the active phase of the process and showed a decreasing trend from the thermophilic to the curing phase. The final compost was characterized by good qualitative characteristics, a significant level of humification [Rossi, L., Piccinini, S., 1999. La qualità agronomica dei compost derivanti da liquami suinicoli. (Agronomic quality of swine manure compost). L'informatore Agrario 38, 29-31] and no odor emissions. This method of managing manure represents an effective, low cost approach that could be an interesting opportunity for swine farms.     

Green house gas emissions from composting and mechanical biological treatment.

In order to carry out life-cycle assessments as a basis for far-reaching decisions about environmentally sustainable waste treatment, it is important that the input data be reliable and sound. A comparison of the potential greenhouse gas (GHG) emissions associated with each solid waste treatment option is essential. This paper addresses GHG emissions from controlled composting processes. Some important methodological prerequisites for proper measurement and data interpretation are described, and a common scale and dimension of emission data are proposed so that data from different studies can be compared. A range of emission factors associated with home composting, open windrow composting, encapsulated composting systems with waste air treatment and mechanical biological waste treatment (MBT) are presented from our own investigations as well as from the literature. The composition of source materials along with process management issues such as aeration, mechanical agitation, moisture control and temperature regime are the most important factors controlling methane (CH4), nitrous oxide (N2O) and ammoniac (NH3) emissions. If ammoniac is not stripped during the initial rotting phase or eliminated by acid scrubber systems, biofiltration of waste air provides only limited GHG mitigation, since additional N2O may be synthesized during the oxidation of NH3, and only a small amount of CH4 degradation occurs in the biofilter. It is estimated that composting contributes very little to national GHG inventories generating only 0.01-0.06% of global emissions. This analysis does not include emissions from preceding or post-treatment activities (such as collection, transport, energy consumption during processing and land spreading), so that for a full emissions account, emissions from these activities would need to be added to an analysis.     

CH4 and N2O from mechanically turned windrow and vermicomposting systems following in-vessel pre-treatment

Methane (CH4) and nitrous oxide (N2O) are included in the six greenhouse gases listed in the Kyoto protocol that require emission reduction. To meet reduced emission targets, governments need to first quantify their contribution to global warming. Composting has been identified as an important source of CH4 and N2O. With increasing divergence of biodegradable waste from landfill into the composting sector, it is important to quantify emissions of CH4 and N2O from all forms of composting and from all stages. This study focuses on the final phase of a two stage composting process and compares the generation and emission of CH4 and N2O associated with two differing composting methods: mechanically turned windrow and vermicomposting. The first stage was in-vessel pre-treatment. Source-segregated household waste was first pre-composted for seven days using an in-vessel system. The second stage of composting involved forming half of the pre-composted material into a windrow and applying half to vermicomposting beds. The duration of this stage was 85 days and CH4 and N2O emissions were monitored throughout for both systems. Waste samples were regularly subjected to respirometry analysis and both processes were found to be equally effective at stabilising the organic matter content. The mechanically turned windrow system was characterised by emissions of CH4 and to a much lesser extent N2O. However, the vermicomposting system emitted significant fluxes of N2O and only trace amounts of CH4. In-vessel pre-treatment removed considerable amounts of available C and N prior to the second stage of composting. This had the effect of reducing emissions of CH4 and N2O from the second stage compared to emissions from fresh waste found in other studies. The characteristics of each of the two composting processes are discussed in detail. Very different mechanisms for emission of CH4 and N2O are proposed for each system. For the windrow system, development of anaerobic zones were thought to be responsible for CH4 release. High N2O emission rates from vermicomposting were ascribed to strongly nitrifying conditions in the processing beds combined with the presence of de-nitrifying bacteria within the worm gut.     

Effect of light Sphagnum peat on odour formation in the early stages of biowaste composting

In the present study, we investigated the effects of two bulking materials, Sphagnum peat and pine wood chips, on the early stages of biowaste composting in two pilot-scale processes. Emphasis was placed on studying the formation conditions of malodorous compost gases in the initial phases of the processes. The results showed that gas emission leaving an open windrow and a closed drum composting system contained elevated concentrations of fermentative microbial metabolites when acid Sphagnum peat (pH 3.2) was used as a bulking material. Moreover, the gas emission of the peat amended drum composter contained a high concentration of odour (up to 450,000 ou m^?3 of air). The highest odour values in the outlet gas of peat amended composts coincided with the elevated concentrations of volatile organic compounds such as acetoin and buthanedion. We conclude that the acidifying qualities of composting substrates or bulking material may intensify odour emission from biowaste composts and prolong the early stages of the composting process.     

Occupational hygiene in a Finnish drum composting plant

Bioaerosols (microbes, dust and endotoxins) and volatile organic compounds (VOCs) were determined in the working air of a drum composting plant treating source-separated catering waste. Different composting activities at the Oulu drum composting plant take place in their own units separated by modular design and constructions. Important implication of this is that the control room is a relatively clean working environment and the risk of exposure to harmful factors is low. However, the number of viable airborne microbes was high both in the biowaste receiving hall and in the drum composting hall. The concentration (geometric average) of total microbes was 21.8 million pcs/m3 in the biowaste receiving hall, 13.9 million pcs/m3 in the drum composting hall, and just 1.4 million pcs/m3 in the control room. Endotoxin concentrations were high in the biowaste receiving hall and in the drum composting hall. The average (arithmetic) endotoxin concentration was over the threshold value of 200 EU/m3 in both measurement locations. In all working areas, the average (arithmetic) dust concentrations were in a low range of 0.6-0.7 mg/m3, being below the Finnish threshold value of 5 mg/m3. In the receiving hall and drum composting hall, the concentrations of airborne microbes and endotoxins may rise to levels hazardous to health during prolonged exposure. It is advisable to use a respirator mask (class P3) in these areas. Detected volatile organic compounds were typical compounds of composting plants: carboxylic acids and their esters, alcohols, ketones, aldehydes, and terpenes. Concentrations of VOCs were much lower than the Finnish threshold limit values (Finnish TLVs), many of the quantified compounds exceeded their threshold odour concentrations (TOCs). Primary health effects due VOCs were not presumable at these concentrations but unpleasant odours may cause secondary symptoms such as nausea and hypersensitivity reactions. This situation is typical of composting plants where the workers are exposed to dozens of VOCs simultaneously. The odour units (OU/m3) were measured using olfactometer. The numbers were 23,000 OU/m3 at the output end of the composting drum and 6300 OU/m3 in the exhaust pipe. Inside the composting hall, the number of odour units was 500 and 560 OU/m3.     

Effective pine bark composting with the dome aeration technology

In South Africa garden refuse is primarily disposed of in domestic landfills. Due to the large quantities generated, any form of treatment would be beneficial for volume reduction, waste stabilization and resource recovery. Dome Aeration Technology (DAT) is an advanced process for aerobic biological degradation of garden refuse and general waste [Paar, S., Brummack, J., Gemende, B., 1999a. Advantages of dome aeration in mechanical-biological waste treatment. In: Proceedings of the 7th International Waste Management and Landfill Symposium, Cagliari, 4-8 October 1999; Paar, S., Brummack, J., Gemende, B., 1999b. Mechanical-biological waste stabilization by the dome aeration method. Environment Protection Engineering 25 (3/99). Mollekopf, N., Brummack, J., Paar, S., Vorster, K., 2002. Use of the Dome Aeration Technology for biochemical stabilization of waste prior to landfilling. In: Proceedings of the Wastecon 2002, Waste Congress and Exhibition, Durban, South Africa.]. It is a non-reactor open windrow composting process, with the main advantage being that the input material needs no periodic turning. A rotting time of only 3-4 months indicates the high efficiency. Additionally, the low capital/operational costs, low energy inputs and limited plant requirements provide potential for use in aerobic refuse stabilization. The innovation in the DAT process is the passive aeration achieved by thermally driven advection through open windrows caused by temperature differences between the degrading material and the outside environment. This paper investigates the application of Dome Aeration Technology to pine bark composting as part of an integrated waste management strategy. A full-scale field experiment was performed at the Bisasar Road Landfill Site in Durban to assess the influence of climate, waste composition and operational conditions on the process. A test windrow was constructed and measurements of temperature and airflow through the material were taken. The process monitoring revealed that prevailing climatic conditions in a subtropical location do not affect the high efficiency of this technology. However, the composition of the input material can be detrimental for production of high quality compost because of a lack of nitrate.     

Continuous monitoring of odours from a composting plant using electronic noses

The odour impact of a composting plant situated in an urbanized area was evaluated by continuously monitoring the ambient air close to the plant during a period of about 4 days using two electronic noses. One electronic nose was installed in a nearby house, and the other one inside the perimeter of the composting plant in order to compare the response of both instruments. The results of the monitoring are represented by tables that report the olfactory class and the odour concentration value attributed to the analyzed air for each of the 370 measurements carried out during the monitoring period. The electronic nose installed at the house detected the presence of odours coming from the composting plant for about 7.8% of the monitoring total duration. Of the odour detections, 86% (25 of 29 measurements) were classified as belonging to the olfactory class corresponding to the open air storage of the waste screening overflows heaps, which was therefore identified to be the major odour source of the monitored composting plant. In correspondence of the measurements during which the electronic nose inside the house detected the presence of odours from the composting plant, the olfactory classes recognized by both instruments coincide. Moreover, the electronic nose at the house detected the presence of odours from the composting plant at issue in correspondence of each odour perception of the house occupants. The results of the study show the possibility of using an electronic nose for environmental odours monitoring, which enables the classification of the quality of the air and to quantify the olfactory nuisance from an industrial source in terms of duration and odour concentration.     

LCA comparison of windrow composting of yard wastes with use as alternative daily cover (ADC)

This study compared the environmental impacts of composting yard wastes in windrows with using them in place of soil as alternative daily cover (ADC) in landfills. The Life Cycle Assessment was made using the SimaPro LCA software and showed that the ADC scenario is more beneficial for the environment than windrow composting. ADC use is also a less costly means of disposal of yard wastes. This finding applies only in cases where there are sanitary landfills in the area that are equipped with gas collection systems and can use yard wastes as alternative daily cover. Otherwise, the environmentally preferable method for disposal of source-separated yard wastes is composting rather than landfilling.     

Morphological classification of bioaerosols from composting using scanning electron microscopy

This research classifies the physical morphology (form and structure) of bioaerosols emitted from open windrow composting. Aggregation state, shape and size of the particles captured are reported alongside the implications for bioaerosol dispersal after release. Bioaerosol sampling took place at a composting facility using personal air filter samplers. Samples were analysed using scanning electron microscopy. Particles were released mainly as small (<1 μm) single, spherical cells, followed by larger (>1 μm) single cells, with aggregates occurring in smaller proportions. Most aggregates consisted of clusters of 2–3 particles as opposed to chains, and were <10 μm in size. No cells were attached to soil debris or wood particles. These small single cells or small aggregates are more likely to disperse further downwind from source, and cell viability may be reduced due to increased exposure to environmental factors.     

Effect of amendments on windrow composting of sugar industry pressmud

Bioconversion of sugar and distillery industrial wastes with other biodegradables into enriched compost is an important possibility in need of research. In this paper, changes in temperature and physico-chemical (pH, NH4+-N, C/N ratio, CEC) parameters during windrow composting, related to biological stabilization of the compost, were studied. The rise in temperature, which occurred as composting progressed, was accompanied by an increase in NH4+-N and the passage of the thermophilic phase to mesophilic took place between 90 and 105 days. This overall pattern was observed in all composting mixes, whereby the concentrations of NH4+-N increased rapidly and then declined gradually over the course of monitoring pari passu with increase in NO3- -N. The C/N ratios of the composting mixes decreased substantially by the 90th day in full thermophilic phase and became comparatively stable later on. Addition of additives showed potential in improving the C/N ratios. Increases in cation exchange capacity (CEC) and the germination index value of a sensitive crop (Raphanus sativus) had value in establishing the optimum degree of maturity. The rise and fall of temperature and changes in NH4+-N concentrations, C/N ratios and CEC over time proved to be reliable indicators of the progress of the composting process for establishing biological stability and compost maturity.     

Influence of compost covers on the efficiency of biowaste composting process

The temperature of matured compost is an indicator of feedstock quality and also a good feedback informing about the suitability of an applied technological procedure. Two independent experiments using the technology of windrow composting at open area were conducted with the final goal to evaluate the effect of compost pile covering (in comparison with uncovered piles) on the course of composting process – behaviour of temperature over time and oxygen content. Two types of sheets were used – Top Tex permeable sheet and impermeable polyethylene sheet. The experiment I (summer months) aimed at comparison of efficiency between the Top Tex sheet cover and the uncovered compost piles, while experiment II (autumn months) compared treatments using the Top Tex sheet and polyethylene sheet by contrast. Within the experiment I the composts consisted of cattle slurry and fresh grass matter at a ratio of 1:1, in case of experiment II consisted of pig/cattle manure, fresh grass matter and chipped material at a ratio of about 1:2:1. The obtained data showed no significant differences among the cover treatments according to ANOVA. The only exception was oxygen content in pile 4 (experiment II) under Top Tex sheet, where a markedly higher oxygen content than under polyethylene sheet was measured during the whole composting period. It was the only case where statistical analysis proved a significant difference; the p-value was 0.0002.     

Fate and effect of linuron and metribuzin on the co-composting of green waste and sewage sludge

The fate and effect of the herbicides linuron and metribuzin on the co-composting of sewage sludge and green waste were addressed in this work. The experiments were conducted in metal cubic containers of 1.0 m³ volume simulating a windrow composting system. A mixture of sludge and green waste was prepared at a ratio of 1:5 v/v. The mixture was split in four equal parts and the two herbicides were added, using a pressure sprayer, as sole or mixed pollutant in each of the three mixtures. The forth mixture was composted without any addition of herbicide, to serve as control. Temperature, physicochemical characteristics, herbicide concentration, carbon dioxide emission, methane emission and microbiological parameters were measured either daily or every time the mixtures were turned, for a period of 80 days. Both herbicides’ concentration decreased significantly resulting in removal efficiencies of 99.1–99.7% and 95.8–96.0% for linuron and metribuzin, respectively. Incubation of microbiologically inactive mixtures at a temperature schedule following the spontaneous temperature evolution in the composters resulted in very little (1–11%) decomposition for both herbicides. Comparison of the variation of physicochemical parameters and microbial populations during composting indicated that both herbicides did not affect the composting process.     

Physical modelling of the composting environment: a review. Part 2: Simulation performance

This paper reviews previously published heat balance data for experimental and full-scale composting reactors, and then presents an evaluation of the simulation performance of laboratory and pilot-scale reactors, using both quantitative and qualitative temperature profile characteristics. The review indicates that laboratory-scale reactors have typically demonstrated markedly different heat balance behaviour in comparison to full-scale systems, with ventilative heat losses of 36-67%, and 70-95% of the total flux, respectively. Similarly, conductive/convective/radiative (CCR) heat losses from laboratory reactors have been reported at 33-62% of the total flux, whereas CCR losses from full-scale composting systems have ranged from 3% to 15% of the total. Full-scale windrow temperature-time profiles from the literature were characterised by the present authors. Areas bounded by the curve and a 40 degrees C baseline (A(40)) exceeded 624 degrees C. days, areas bounded by the curve and a 55 degrees C baseline (A(55)) exceeded 60 degrees C days, and times at 40 and 55 degrees C were >46 days and >24 days, respectively, over periods of 50-74 days. For forced aeration systems at full scale, values of A(40) exceeded 224 degrees C days, values of A(55) exceeded 26 degrees C days, and times at 40 and 55 degrees C were >14 days and >10 days, respectively, over periods of 15-35 days. Values of these four parameters for laboratory-scale reactors were typically considerably lower than for the full-scale systems, although temperature shape characteristics were often similar to those in full-scale profiles. Evaluation of laboratory-, pilot- and full-scale profiles from systems treating the same substrate showed that a laboratory-scale reactor and two pilot-scale reactors operated at comparatively high aeration rates poorly simulated full-scale temperature profiles. However, the curves from two moderately insulated, self-heating, pilot-scale reactors operated at relatively low aeration rates appeared to closely replicate full-scale temperature profiles. The importance of controlling aeration rates and CCR losses is discussed and further work suggested in order to investigate the links between simulation of the composting environment and process performance.     

Environmental assessment of garden waste management in the Municipality of Aarhus, Denmark

An environmental assessment of six scenarios for handling of garden waste in the Municipality of Aarhus (Denmark) was performed from a life cycle perspective by means of the LCA-model EASEWASTE. In the first (baseline) scenario, the current garden waste management system based on windrow composting was assessed, while in the other five scenarios alternative solutions including incineration and home composting of fractions of the garden waste were evaluated. The environmental profile (normalised to Person Equivalent, PE) of the current garden waste management in Aarhus is in the order of −6 to 8 mPE Mg⁻¹ ww for the non-toxic categories and up to 100 mPE Mg⁻¹ ww for the toxic categories. The potential impacts on non-toxic categories are much smaller than what is found for other fractions of municipal solid waste. Incineration (up to 35% of the garden waste) and home composting (up to 18% of the garden waste) seem from an environmental point of view suitable for diverting waste away from the composting facility in order to increase its capacity. In particular the incineration of woody parts of the garden waste improved the environmental profile of the garden waste management significantly.     

Mass balances and life cycle inventory of home composting of organic waste

A comprehensive experimental setup with six single-family home composting units was monitored during 1 year. The composting units were fed with 2.6-3.5 kg organic household waste (OHW) per unit per week. All relevant consumptions and emissions of environmental relevance were addressed and a full life-cycle inventory (LCI) was established for the six home composting units. No water, electricity or fuel was used during composting, so the major environmental burdens were gaseous emissions to air and emissions via leachate. The loss of carbon (C) during composting was 63-77% in the six composting units. The carbon dioxide (CO(2)) and methane (CH(4)) emissions made up 51-95% and 0.3-3.9% respectively of the lost C. The total loss of nitrogen (N) during composting was 51-68% and the nitrous oxide (N(2)O) made up 2.8-6.3% of this loss. The NH(3) losses were very uncertain but small. The amount of leachate was 130 L Mg(-1) wet waste (ww) and the composition was similar to other leachate compositions from home composting (and centralised composting) reported in literature. The loss of heavy metals via leachate was negligible and the loss of C and N via leachate was very low (0.3-0.6% of the total loss of C and 1.3-3.0% of the total emitted N). Also the compost composition was within the typical ranges reported previously for home composting. The level of heavy metals in the compost produced was below all threshold values and the compost was thus suitable for use in private gardens.     

Mechanical-biological waste treatment and the associated occupational hygiene in Finland

A special feature of waste management in Finland has been the emphasis on the source separation of kitchen biowaste (catering waste); more than two-thirds of the Finnish population participates in this separation. Source-separated biowaste is usually treated by composting. The biowaste of about 5% of the population is handled by mechanical-biological treatment. A waste treatment plant at Mustasaari is the only plant in Finland using digestion for kitchen biowaste. For the protection of their employees, the plant owners commissioned a study on environmental factors and occupational hygiene in the plant area. During 1998-2000 the concentrations of dust, microbes and endotoxins and noise levels were investigated to identify possible problems at the plant. Three different work areas were investigated: the pre-processing and crushing hall, the bioreactor hall and the drying hall. Employees were asked about work-related health problems. Some problems with occupational hygiene were identified: concentrations of microbes and endotoxins may increase to levels harmful to health during waste crushing and in the bioreactor hall. Because employees complained of symptoms such as dry cough and rash or itching appearing once or twice a month, it is advisable to use respirator masks (class P3) during dusty working phases. The noise level in the drying hall exceeded the Finnish threshold value of 85 dBA. Qualitatively harmful factors for the health of employees are similar in all closed waste treatment plants in Finland. Quantitatively, however, the situation at the Mustasaari treatment plant is better than at some Finnish dry waste treatment plants. Therefore is reasonable to conclude that mechanical sorting, which produces a dry waste fraction for combustion and a biowaste fraction for anaerobic treatment, is in terms of occupational hygiene better for employees than combined aerobic treatment and dry waste treatment.     

Feasibility study of a passive aeration reactor equipped with vertical pipes for compost stabilization of cow manure.

Pilot-scale composting was carried out with cow manure to evaluate the performances of two passive aeration systems: a conventional passive aeration system equipped with horizontal pipes and an unusual passive aeration method based on air delivery by means of vertical pipes. The effects of both types of passive aeration apparatus were investigated in order to determine the degree of composting rate by continuously monitoring temperature, moisture content, organic matter, electrical conductivity, pH and C/N ratio in the piles. Temperatures in the range of thermophily (55-65 degrees C) were reached in all runs within 1-2 days then lasting for about 1 week, a span long enough for pathogen abatement. Results suggest that passive aeration carried out by vertical pipes is more effective for air delivery into compost piles than conventional passive aeration of air adduction with horizontal pipes. The variation in the number of vertical pipes was revealed to be an important parameter for the control of composting rate and temperature. Composting rates estimated from the heat balance equation were substantially in agreement with those computed through the conversion ratio of total organic matter decrement. The conversion ratios and composting rates obtained in this study using passive aeration with vertical pipes were well aligned with those found using forced air delivery systems.     

Composting of vegetable waste.

The effects of the aeration, seeding, and agitation on the composting of vegetable waste were studied in a laboratory-scale reactor. Experimental results showed that the final product at the end of a 4-day composting period met multiple maturity indices suggested by many researchers. The evolution of carbon dioxide during the composting process could be modelled with a modified Gompertz equation that described the bacteria growth successfully. Multivariate regression analysis was used to study the effects of operating parameters on the carbon conversion. The response surface contour plots were constructed using the regression equation for the examination of the dependence of carbon conversion on operating parameters. The maximum carbon conversion of 14.54% was obtained when the percentage of seeding was set at 14.5%, the air suction rate was set at 2.6 L kg(-1) dry-solid min(-1), and the agitator operated half of the time, alternating on and off for every 5 min. Future work will focus on the application of the data and the experience gained in this work to composters of pilot and semi-commercial scales.