An alternative supercritical fluid extraction system for aqueous matrices and its application in pesticides residue analysis

Supercritical fluid extraction (SFE) is a rapid and convenient method for the isolation of organic compounds from environmental samples. This paper describes a supercritical carbon dioxide (CO2) extraction system that uses a newly designed extraction cell to recover organic compounds from an aqueous matrix. Analysis of the extracts by gas chromatography-electron capture detector (GC-ECD) indicated that the herbicide trifluralin (2,6-dinitro-N,N-dipropyl-4-trifluoromethylaniline) could be quantitatively extracted by using the SFE system proposed with small amounts of sample. The percentage of recovery obtained with the SFE system described was twice as high as the result obtained using a conventional solid-phase extraction technique. Extraction by SFE was completed in a short period of time using a simple and low-cost home-made system that did not require the use of organic solvents.     

Study of the distribution of the polychlorinated biphenyls in the milk fat globule by supercritical fluid extraction

The distribution of polychlorinated biphenyls (PCBs) in the milk fat globule has been studied by sequential extraction of four different lipidic fractions from powdered full-fat milk with supercritical carbon dioxide. Extractions were carried out in the dynamic mode in the pressure range 13.6-23.3 MPa at a temperature of 50 degrees C. The levels of PCBs and short-chain triglycerides (SCT), medium-chain triglycerides (MCT) and long-chain triglycerides (LCT), as well as the cholesterol in these four supercritical fluid extraction (SFE) fractions were determined. Extracts obtained at lower pressures were found to be enriched in PCBs, SCT, MCT and cholesterol, while the concentrations of all these analytes decreased for subsequent extractions. Satisfactory quadratic correlations were found between the PCB and SCT and MCT levels (r2 in the range 0.9-0.999), and between the PCB and cholesterol levels (r2 in the range 0.8-0.999, except for PCB 105) determined in the SFE fractions. These results suggested a similar distribution of the PCBs and the cholesterol in the milk fat globule. This conclusion was also supported by the comparison of the PCBs and the cholesterol chemical structures as well as by the total PCB levels determined by SFE to those obtained by using different extraction methods. The classical requirement for the analysis of this kind of lipophilic pollutants of an exhaustive extraction of the lipids of the matrix to ensure their quantitative recovery has been revised.     

Evaluation of a multiresidue method for pesticides in cereals using supercritical fluid extraction and gas chromatographic detection

Supercritical fluid extraction (SFE) was evaluated to be applied for residue analysis of 22 gas chromatography/electron capture detector-nitrogen phosphorus detector (GC/ECD-NPD) amenable pesticides in rice, wild rice and wheat. Samples were extracted with supercritical carbon dioxide at 200 atm pressure and 50°C temperature, using methanol as a static modifier. Mean recoveries obtained with the proposed SFE method at two spiking levels with four replicates per level are compared with those obtained with an ethyl acetate-based solvent extraction/gel permeation chromatography (GPC) clean up method. Both methods gave consistent high recoveries for almost all the pesticides from all the commodities with overall mean recoveries higher than 70% with relative standard deviations lower than 20%. Remarkable exceptions were captafol and dimethoate, for which low and/or non-reproducible recoveries were obtained with the SFE method. Residue levels determined with both methods in nine different incurred samples of wheat, containing some of the studied pesticides, were very similar, but, in all cases, slightly higher levels were determined with the SFE method.     

An alternative supercritical fluid extraction system for aqueous matrices and its application in pesticides residue analysis

Abstract

Supercritical fluid extraction (SFE) is a rapid and convenient method for the isolation of organic compounds from environmental samples. This paper describes a supercritical carbon dioxide (CO₂) extraction system that uses a newly designed extraction cell to recover organic compounds from an aqueous matrix. Analysis of the extracts by gas chromatography‐electron capture detector (GC‐ECD) indicated that the herbicide trifluralin (2,6‐dinitro‐N,N‐dipropyl‐4‐trifluoromethylaniline) could be quantitatively extracted by using the SFE system proposed with small amounts of sample. The percentage of recovery obtained with the SFE system described was twice as high as the result obtained using a conventional solid‐phase extraction technique. Extraction by SFE was completed in a short period of time using a simple and low‐cost home‐made system that did not require the use of organic solvents.     

Discrimination and thermal degradation of toxaphene compounds in capillary gas chromatography when using split/splitless and on-column injection

Technical toxaphene and a 22-component Reference Mixture were analyzed using capillary gas chromatography with split/splitless injection (SSL) and on-column injection (OC). In both techniques, electron-capture, negative ionization mass spectrometry (ECNI-MS) was used for detection of chlorobornanes, chlorocamphenes and related compounds. Significant discrimination of highly chlorinated congeners was observed as a result of incomplete transfer of these compounds from the vaporizer to the analytical column when using SSL. This resulted in a much lower response for nona- and decachloro congeners than when using OC. In addition, several toxaphene components, especially the chlorobornanes with gem dichloro substitution on the six-member carbon ring, undergo thermal degradation when using SSL. Some of these congeners are major components of technical toxaphene, but generally are not present, except at low concentrations, in environmental and biological samples. Therefore, technical toxaphene may be discriminated and/or degraded differently than toxaphene compounds in environmental samples when using SSL. This results in significant bias of the quantitative data when using the technical material as a reference. OC suffers much less from these deficiencies and, therefore, is a preferable technique for toxaphene analysis.     

Supercritical Fluid Extraction for Forensic Analysis of Hydrocarbons in Soil

Supercritical fluid extraction (SFE) was investigated to evaluate its potential for obtaining high quality chromatographic fingerprints from soils encountered in environmental investigations. While the volatile and semivolatile fractions of light nonaqueous phase liquid (LNAPL) samples can be “fingerprinted” in a single chromatographic run, it is commonly not possible to obtain samples of LNAPL in the locations of interest. For this and other reasons, it was desirable to develop this method (SFE) of soil extraction, which allows chromatographic fingerprinting of the same quality routinely obtained with LNAPL so that environmental forensic investigations could be extended to areas beyond those containing LNAPL in monitoring wells. In this study, SFE was compared to conventional dichloromethane extraction. Both artificially spiked soil and soil from petroleum release sites were tested. Since water can be a problem when using the SFE method, particular attention was given to handling soils with high moisture contents. The SFE extracts showed excellent retention of low molecular components, including pentanes. Gas chromatography of SFE extracts yielded molecular distributions that showed no significant bias toward either low or high molecular weight components. These results show that SFE can be used to obtain an unbiased, single-run chromatographic “fingerprint” of both volatile and semivolatile hydrocarbons in contaminated soil samples.     

Sample storage and extraction efficiencies in determination of polycyclic and nitro musks in sewage sludge

Analytical technology is continuously improving, developing better methods for isolating and concentrating trace compounds in environmental samples. Polycyclic and nitro musks (PNMs) are one group of emerging trace compounds detected in municipal wastewater. Differences in sample storage, preparation, and extraction methods for their measurement have led to variability in results. We analyzed 11 PNMs by GC/MS and compared the results of different storage times and extraction methods (supercritical fluid (SFE) or microwave-assisted (MAE)) for 202 samples of primary sludge, waste activated sludge (WAS), raw sludge, and aerobically/anaerobically digested biosolids collected from Canadian municipal wastewater treatment plants. Sixty-three air-dried samples were extracted by SFE, and 139 air-dried, centrifuged, or filtered samples were extracted by MAE. The mean surrogate recoveries were 89% (standard deviation (SD)=11%) for d(10)-anthracene by SFE and 88% (SD=14%) for d(10)-phenanthrene by MAE. Storage study results showed that PNM concentrations changed by a mean of 7% and 9% for primary sludge and WAS respectively after four weeks and decreased up to 25% after 13.5 months of storage in amber glass containers at -18 degrees C. Air-drying of sludge at room temperature caused losses of about 50% of PNM concentrations compared to centrifugation. The proportions of PNMs present in the liquid phase of sludge samples were less than 5% compared to proportions in the sludge solids. The most complete liquid-solid separation was achieved by filtration of frozen/thawed sludge samples, producing a liquid phase that contained less than 1% of the total musk content of the sample.     

Comparison of supercritical fluid extraction and Soxhlet extraction for the determination of PCBs in seaweed samples

The efficiency of supercritical fluid extraction for the determination of 12 polychlorinated biphenyls from algae samples is compared to Soxhlet extraction. Analytical detection limits for the individual congeners ranged from 0.62 microgl(-1) to 19 microgl(-1). Recovery was tested for both methods using standard addition procedure. At maximum spike level of concentration, the mean recoveries were not significantly different (P>0.05) of all PCBs studied, with the exception of PCBs 28, 52, 77 and 169. Method precision for Soxhlet extraction (< or =3.9%) was slightly better than for SFE (< or =9.2%). Although both methods yield comparable results, SFE offers the advantage of detecting all PCBs studied at lower concentrations, reducing extraction time, and reducing the amount of solvents needed. The optimized methods were applied to the analysis of three real seaweed samples, except for PCB101 the concentrations of all PCBs were low or below the detection limits. The levels of PCB101 found in sample 1 were 6.6+/-0.54 ng g(-1) d.w., in sample 2 the levels were 8.2+/-0.86 ng g(-1) d.w. and in sample 3 they were 7.7+/-0.08 ng g(-1) d.w.     

Development of supercritical carbon dioxide extraction with a solid phase trap for dioxins in soils and sediments

A method involving supercritical fluid extraction (SFE) with a solid phase trap containing activated alumina was investigated for the rapid analysis of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), and dioxin like polychlorinated biphenyls (DL-PCBs) in soils and sediments. The samples were extracted by using supercritical carbon dioxide with water (2% versus CO(2) flow velocity) being used as an entrainer at a pressure of 30 MPa and a temperature of 130 degrees C for 50 min. The extracts were adsorbed on an activated alumina trap that was maintained at a temperature of 150 degrees C, and then, PCDD/DFs and DL-PCBs were eluted with 20 ml of hexane at 60 degrees C. After concentration, they were measured with a high-resolution gas chromatograph interfaced to a high-resolution mass spectrometric detector. The average concentrations of PCDD/DFs and DL-PCBs corresponded to the results obtained by the conventional method, and the reproducibility of this SFE method was below 21% of the relative standard deviations for all samples. The total time required for the analysis of the pretreatment of this method was only 2 h.     

Variation of toxaphene indicator compounds in fish from single fishing grounds: conclusions for sampling

The levels of three toxaphene indicator compounds were determined in individual lots of herring, redfish, Greenland halibut and farmed salmon. Concentration levels of the three marine fish species were characterised by a right-skewed frequency distribution whereas residue concentrations in farmed salmon were normally distributed. The toxaphene concentrations in the edible part of redfish, herring and Greenland halibut were found to be positively correlated to the sizes and thus to age. As results show, for representative sampling of a landed catch, not more than 10 individual fishes from typical size classes of a lot are necessary for a pooled sample.     

Total toxaphene and specific congeners in fish from the Yukon, Canada

Toxaphene is one of the major persistent organic pollutants with global environmental impacts. We have measured total toxaphene and specific congeners concentrations in 19 fish samples collected from the Yukon, Canada using gas chromatography coupled to ion trap MS/MS. The total toxaphene concentrations ranged from 42 to 242 ng/g (mean = 107+/-61 ng/g). The sum of the three specific congeners (Parlar 26, 50 and 62) was within 10-55 ng/g. The ratio of the sum of the three congeners to the total toxaphene varied between 8% and 25% in the fish samples but the ratio may be species specific. Our results suggest that consumption of these Yukon fish should have minimal risk of toxaphene exposure.     

Airborne concentrations of toxaphene congeners at Point Petre (Ontario) using gas-chromatography-electron capture negative ion mass spectrometry (GC-ECNIMS).

A reliable analytical method has been developed using GC-ECNIMS for the determination of individual toxaphene congeners in ambient air. To allow a reasonable comparison with previous data for toxaphene reported by Muir and co-workers using GC-ECD, this method has adopted their approach of focussing upon the identification and quantification of specific peaks or clusters ("T" species) typically observed in environmental samples, with the sum of these "T" species then being reported as "total toxaphene". Technical toxaphene has been used as the analytical standard, but independent response factors have been assigned to the target peaks and clusters. Because of the appreciable variability in ECNIMS response shown by individual toxaphene congeners, this is considered to be a reasonable and potentially more accurate procedure than the application of a "single response factor" used by many other workers. The methodology has been used for the determination of toxaphene in air samples collected over the annual cycle in 1992 and then from October 1995 to September 1997 at Point Petre, Ontario. Of the forty-four calibrated components, only 10 were detected in all of the air samples collected over the latter 2-year period. Airborne concentrations of toxaphene (defined as the sum of the calibrated components) range from 0.9 pg/m3 to 10.1 pg/m3. A clear seasonality has been observed, with a summer-to-winter concentration ratio of about 6.     

Selective supercritical fluid extraction as a tool for determining the PCB fraction accessible for uptake by chironomid larve in a limnic sediment

Selective supercritical fluid extraction (SFE) at 40 degrees C, 400 bar and 60 min was used to selectively remove bioavailable PCBs from a naturally contaminated limnic sediment. The extraction decreased the sediment concentrations of the nine studied PCBs by 54% (on average). Chironomid larvae were thereafter cultured in pre-extracted sediment as well as in untreated sediment to study the differences in uptake of PCBs in the two cultures. While the prevailing equilibrium partitioning (EqP) theory predicts a 54% decrease in PCB uptake by the chironomids in the pre-extracted sediment, with a maintained biota-to-sediment accumulation factor (BSAF), a decrease in PCB uptake by 91% was observed. For all investigated PCBs the BSAFs were on average 81% lower in the cultures with pre-extracted sediment than in the untreated systems. The data allowed for a calculation of the bioavailable fraction, which was estimated to 60%. This is very close to the 54% removed by selective SFE, demonstrating the possibility of using SFE as a tool to determine the bioavailable PCB fraction in a polluted sediment.     

Extraction procedure optimization for perfluorooctane sulfonate and perfluorooctanoic acid in food packaging determination by LC-MS/MS

This research aimed to optimize the extraction method parameters for sample pretreatment and determine the levels of perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA) contamination in food packaging made of paper. Techniques used were pressurized liquid extraction (PLE) followed by liquid chromatography coupled with tandem mass spectrometry (LC-MS/MS). Influence parameters of PLE were carefully evaluated for extracted concentration of samples in low level (ng g^?1). The study found that the optimal conditions for PLE were 30 min static extraction time with a flush volume of 100% cell volume and one extraction cycle at 80°C and 1,000 psi. The extraction technique validated the absolute recovery from PFOS and PFOA fortified control samples at three different levels (5, 50, and 200 ng g^?1), with seven repeats at each fortification level. The average recoveries were 79% or higher, with relative standard deviation (RSD) less than 11%. Optimization of the PLE method was established based on recovery data, accuracy, precision, and repeatability of the method. Using optimal PLE technique, PFOS and PFOA were extracted from 34 food-packaging samples collected in Thailand. PFOS and PFOA were detected in all kinds of collected samples, with average concentrations of 4.89 and 2.87 ng g^?1, respectively. The concentrations of PFOS and PFOA were highest in fast-food container samples: 36.99 and 9.99 ng g^?1, respectively.     

Levels of toxaphene congeners in fish from Danish waters

The levels of toxaphene congeners, in addition to PCB congeners and organochlorine pesticides, were determined in various fish samples from different Danish waters. While PCB-153 and p,p'-DDE show different levels depending on the fishing area, with highest levels in fish from the Western Baltic Sea, toxaphene was detected in all the samples investigated at a more constant level. The distribution of the three toxaphene congeners Parlar #26, #50 and #62 depends on the fishing area, with the Western Baltic Sea being different from the other waters by having almost equal levels of toxaphene congeners #26 and #50.     

Measuring bioavailability of polychlorinated biphenyls in soil to earthworms using selective supercritical fluid extraction

If the release mechanisms during selective chemical extraction of persistent organic pollutants (POP) mimic release mechanisms in natural systems during biological uptake, then a selective non-exhaustive extraction could give a quantitative measure of the bioavailable POP fraction. Supercritical fluid extraction (SFE) is suggested as a possible technique to estimate the amount of bioavailable polychlorinated biphenyls (PCBs) at contaminated sites and hence serve as a new tool in risk assessment. The uptake of PCBs by earthworm (Eisenia foetida) was investigated. PCB contaminated soil was pre-extracted with selective non-exhaustive SFE (50 degrees C, 350 bar, 1h), which removed on average 70% of the individual PCBs. Earthworms were placed in this pre-extracted soil, as well as in untreated soil. After 10 days, the PCB uptake by earthworms in the two systems was compared. The bioaccumulation factor (BAF) was 83% lower in the pre-extracted system than in the untreated system, demonstrating that SFE extracts primarily bioavailable contaminants. From the data, the bioavailable fraction could also be calculated to be 75%, which is very close to the 70% removed by SFE under the applied conditions. This suggests that the chemical methodology is capable of measuring the bioavailable fraction very accurately in this system.     

Fatty acid profile and elemental content of avocado (Persea americana Mill.) oil –effect of extraction methods

Interest in vegetable oil extracted from idioblast cells of avocado fruit is growing. In this study, five extraction methods to produce avocado oil have been compared: traditional solvent extraction using a Soxhlet or ultrasound, Soxhlet extraction combined with microwave or ultra-turrax treatment and supercritical fluid extraction (SFE). Traditional Soxhlet extraction produced the most reproducible results, 64.76 ± 0.24 g oil/100 g dry weight (DW) and 63.67 ± 0.20 g oil/100 g DW for Hass and Fuerte varieties, respectively. Microwave extraction gave the highest yield of oil (69.94%) from the Hass variety. Oils from microwave extraction had the highest fatty acid content; oils from SFE had wider range of fatty acids. Oils from Fuerte variety had a higher monounsaturated: saturated FA ratio (3.45–3.70). SFE and microwave extraction produced the best quality oil, better than traditional Soxhlet extraction, with the least amount of oxidizing metals present.     

Fatty acid profile and elemental content of avocado (Persea americana Mill.) oil--effect of extraction methods

Interest in vegetable oil extracted from idioblast cells of avocado fruit is growing. In this study, five extraction methods to produce avocado oil have been compared: traditional solvent extraction using a Soxhlet or ultrasound, Soxhlet extraction combined with microwave or ultra-turrax treatment and supercritical fluid extraction (SFE). Traditional Soxhlet extraction produced the most reproducible results, 64.76 ± 0.24 g oil/100 g dry weight (DW) and 63.67 ± 0.20 g oil/100 g DW for Hass and Fuerte varieties, respectively. Microwave extraction gave the highest yield of oil (69.94%) from the Hass variety. Oils from microwave extraction had the highest fatty acid content; oils from SFE had wider range of fatty acids. Oils from Fuerte variety had a higher monounsaturated: saturated FA ratio (3.45-3.70). SFE and microwave extraction produced the best quality oil, better than traditional Soxhlet extraction, with the least amount of oxidizing metals present.     

Preliminary examination of contaminant loadings in farmed salmon, wild salmon and commercial salmon feed

This pilot study examined five commercial salmon feeds, four farmed salmon (one Atlantic, three chinooks) and four wild salmon (one chinook, one chum, two sockeyes) from the Pacific Coast for PCBs (112 congeners), polybrominated diphenylethers (PBDEs - 41 congeners), 25 organochlorine pesticides (OPs), 20 polycyclic aromatic hydrocarbons (PAHs), and methyl and inorganic mercury. The farmed salmon showed consistently higher levels of PCBs, PBDEs, OPs (except toxaphene) than the wild salmon. The mean concentrations in pg/g were 51,216 vs 5302 for total PCBs; 2668 vs 178 for total PBDEs; 41,796 vs 12,164 for total OPs (except toxaphene). The farmed salmon levels are likely a consequence of the elevated level of contamination found in the commercial salmon feed (mean concentrations in pg/g were 65,535 for total PCBs; 1889 for total BPDEs; 48,124 for total OPs except toxaphene). Except for a single high wild chinook value, PAHs were highest in the feed samples followed by the farmed fish and the three other wild fish. The Bio-Oregon-1996 feed of hatchery origin showed a level of PAHs ten times higher than any other feed. The genotoxic implications of such a high PAH level are considered for juvenile chinook salmon. Toxaphene and methyl mercury concentrations were not notably different between the wild and farmed salmon. There was no clear low contaminant brand of salmon feed. The human health implications of eating farmed salmon are considered from the perspective of the current WHO and Health Canada (2000) tolerable daily intake (TDI) values for PCBs. Based on a TDI of 1 pg TEQ/kg bw/day, this analysis indicated a safety concern for individuals who on a regular weekly basis consume farmed salmon produced from contaminated feed.     

Toxaphene in minke whales (Balaenoptera acutorostrata) from the North Atlantic

Toxaphene contamination of minke whales (Balaenoptera acutorostrata) from North Atlantic waters was examined for the first time. Total toxaphene and SigmaCHB (sum of 11 chlorobornanes) concentrations in blubber samples ranged from 170+/-110 and 41+/-39 ng/g lipid weight (l.w.) for female minke whales from southeastern Greenland to 5800+/-4100 and 1100+/-780 ng/g l.w. for males from the North Sea, respectively. Very large variations in toxaphene concentrations among sampling areas were observed suggesting a spatial segregation of minke whales. However, much of the apparent geographical discrimination was explained by the seasonal fluctuation of animal fat mass. Patterns of CHBs in males revealed that recalcitrant CHBs were in higher proportions in animals from the more easterly areas than in animals from the more westerly areas. This trend may be influenced by the predominance of the US, over the European, input of toxaphene to North Atlantic waters.