喷射方式对气泡雾化细水雾灭火效率的影响分析

气泡雾化技术是一种双流体细水雾发生方法,本文利用现有的气泡雾化细水雾灭火系统进行了模拟实验,对该系统在不同喷射方式下对扑灭汽油火的有效性进行了研究,并进行了分析。实验发现:喷射距离和喷射角度对灭火效率都有影响;水平条件下灭火效率很低;不同灭火过程对应不同的灭火机理。     

添加剂对细水雾高原灭火性能影响的试验研究

为了发展适应于高原地区低压低氧环境下的火灾防治技术,基于高原地区建筑特点和防火重要性,建立用细水雾灭火技术来防治高原建筑火灾的方法。在中国拉萨进行细水雾添加剂灭火模拟试验,研究添加剂FeCl_2和NaCl对细水雾熄灭汽油和柴油池火的灭火性能的影响,分析试验过程的温度、烟气、辐射热流变化规律。结果表明,在拉萨地区低压低氧的环境下,分别含质量分数为1.5%FeCl_2和10%NaCl的细水雾对柴油池火的灭火效率较高,而汽油池火初期受到了抑制,但随后出现了强化现象,最终未被熄灭。含添加剂FeCl_2和NaCl的细水雾对高原地区柴油池火有较高的灭火效率。     

细水雾熄灭障碍物火的实验研究和数值模拟

为了研究细水雾灭火系统在网状和条状障碍物阻隔条件下的灭火效果,采用全尺寸试验研究和数值模拟的方法研究了障碍物的形状,位置,遮挡面积以及细水雾工作压力对灭火效果的影响.实验结果表明:提高压力有助于快速有效地熄灭障碍物火;障碍物的位置是影响灭火效果的重要因素,近距离的覆盖使细水雾难以进入火区.障碍物下出现局部高温区,余火难以扑灭,灭火时间至少需要56 s;而障碍物距离火源较远时,卷吸作用下细水雾仍能均匀的进入火区,发挥冷却作用,灭火时间在18 s以内;网状障碍物的遮挡面积,对灭火效果影响不大;相同遮挡面积条件下,条状障碍物火比较难熄灭.     

含氯化亚铁添加剂细水雾灭火有效性的实验研究

为了提高常规细水雾的灭火有效性,拓展其应用范围,本文采用小尺度实验的方法,研究了含氯化亚铁添加剂细水雾在不同燃料种类、添加剂浓度、压力下扑灭池火的有效性。实验结果表明：向细水雾中添加氯化亚铁,显著地影响了它的灭火性能;细水雾的灭火时间随着加入的氯化亚铁的质量浓度变化而发生改变,而且存在一个最短灭火时间浓度;细水雾喷头的工作压力和燃料的类型也对细水雾的灭火性能有影响,喷头工作压力越大,细水雾的平均灭火时间越短;在相同的实验条件下,细水雾灭煤油火的时间要短于灭乙醇火的时间。     

细水雾灭垂直立面火实验研究

对细水雾灭垂直立面火进行了实验研究。结果表明,喷头和火源之间存在一个最佳的水平距离,在此距离上,细水雾能够扑灭的火源尺寸或火源的位置范围最大。喷头向燃料表面垂直喷射时,灭火时间最短。斜向喷射时,随着喷射角度的增大,灭火时间逐渐增大,直至灭火失败。喷头斜向上喷射时的灭火效果优于斜向下喷射时的灭火效果,能够在更大的喷射距离上扑灭相同规模的火源。     

受限空间脉冲细水雾灭火数值模拟

为研究脉冲细水雾灭火效果和灭火机理,采用FDS软件对连续和脉冲细水雾熄灭受限空间油盘火进行了数值模拟。通过模拟和理论分析确定了脉冲细水雾周期为8 s开启、8 s暂停,并设置了冷却和窒息两种灭火条件,对两种细水雾熄灭不同尺寸的柴油池火进行了研究。结果表明:连续细水雾无法熄灭直径15 cm和20 cm的小尺寸油盘火,对直径25 cm中尺寸油盘火的灭火机理为冷却,对直径为30cm和35 cm大尺寸油盘火的灭火机理为窒息;脉冲细水雾能够熄灭不同尺寸的油盘火,且灭火效率高,火焰熄灭均发生在喷头暂停喷水期间,灭火机理为水雾蒸发稀释氧气而窒息。     

含F-500的低压细水雾抑制B类火灾的实验研究

通过全尺寸实验研究低压细水雾对抑制和熄灭B类火灾的有效性。分别使用圆形和方形油盘,以汽油和柴油为燃料进行低压细水雾灭火实验,并进一步研究含微胶囊F-500添加剂的细水雾灭火效果。结果表明,低压细水雾对抑制和熄灭B类火具有一定的有效性,但容易出现灭大火容易灭小火难的现象,并且对于"角落火"难以扑灭。而添加了微胶囊F-500的低压细水雾,灭火效率较纯水细水雾提高约3～5倍,能有效扑灭死角火,同时提高火场能见度。分别用1%、3%、6%的F-500溶液作为灭火介质,实验表明,不同浓度的F-500溶液具有不同的灭火效果。综合考虑经济性和有效性因素:对于大多数B类火灾场合,F-500溶液的最佳配比为1%;对于危险性大或火灾荷载大的场合,微胶囊F-500水溶液的最佳配比为3%。     

两相射流促进细水雾灭火技术发展

压缩气体射流与水射流混合后所产生的气-水两相射流,可获得连续、高速喷射的细水雾,水滴粒径小,穿入火焰的能力强,可沿水平方向射入火焰中,比喷淋方式水雾灭火可节省90%的用水量,缩短了灭火时间,发挥了细水雾的灭火优势,是细水雾灭火技术的最新发展。所制成的便携式、车载式、固定式的两相射流细水雾灭火装置,可扑灭多种类型的火灾,尤其适合用于扑灭有人存在的空间的火灾。以涡喷发动机为喷射动力的气-水两相射流喷射系统,制成了超大功率的喷射雾状水的消防装备,大幅度提高了控制油、气大火火势的能力和灭火效率。气-水两相射流还有稀释、吹散泄漏出的可燃性气体,防止其点燃的功能,适合于在天然气和有毒有害气体泄漏事故抢险救援中使用。将压缩气体和泡沫液按比例混和后喷射的压缩空气泡沫喷射系统,产生了喷射“干泡沫”的消防车,使灭火用水的利用率提高了8倍,被称为是世界最先进的泡沫灭火技术。气-水两相射流促进了灭火技术革命性的发展,新型的气-水两相射流消防装备不断涌现,展示出了广阔的应用前景。     

基于数值模拟的细水雾在汽车涂装车间喷漆室的应用研究

采用FDS软件对细水雾扑救汽车涂装车间喷漆室火灾的灭火效能进行数值模拟分析,着重探讨了喷漆室纵向通风、细水雾雾滴粒径、雾滴喷射速度、汽车障碍物等对扑灭油漆火的影响。模拟结果表明:在细水雾与油漆火的相互作用过程中,细水雾对火源的表面冷却和隔氧窒息作用显著;为了防止室内氧气得到补充,在开启细水雾灭火的同时应当联动控制关闭纵向通风系统;在模拟工况条件下雾滴粒径为100μm~300μm的细水雾灭火效果优于粒径为400μm、500μm的细水雾;雾滴在一定喷射速度范围内速度越大灭火效果越好,喷射速度为10m/s的雾滴灭火效果明显优于3m/s和5m/s的雾滴,但是为了防止火焰横向蔓延,喷射速度不宜过高;在汽车障碍物火灾中部分微小的细水雾雾滴受到火焰的卷吸作用,可以绕过障碍物进入火区发挥冷却作用,细水雾灭火系统能够有效控制障碍物火灾,可以应用于汽车涂装车间喷漆室。     

受限空间脉冲细水雾系统关键参数试验与数值模拟研究北大核心CSCD

为了研究脉冲细水雾的关键参数,采用FDS软件对不同周期的脉冲细水雾熄灭受限空间油盘火进行了数值模拟,分析了脉冲周期的优化设置、细水雾的灭火效果和灭火机理。根据模拟结果进行参数设置,建立了脉冲细水雾试验平台,对脉冲细水雾熄灭不同尺寸油盘火进行了试验研究,并与数值模拟结果对比。研究表明:脉冲细水雾的最佳周期应满足喷头开启时间接近雾滴降至燃料表面的时间,暂停时间接近雾滴的生存时间;脉冲细水雾能熄灭不同尺寸火源,其灭火效果优于连续细水雾,雾滴蒸发效率更高,灭火机理为水雾蒸发稀释氧气而窒息灭火。     

Characteristics of large cooking oil pool fires and their extinguishment by water mist

Large cooking oil pool fires, occurring in industrial oil cookers, present a severe hazard to food processing plants due to their size and the large amount of hot oil involved. This paper reports a series of full-scale fire experiments conducted in a large industrial oil cooker mock-up. The characteristics of large cooking oil pool fires and the effect of oil depth and hood position in the oil cooker on fire growth were studied. The use of water mist for extinguishing large oil pool fires and their extinguishing performance under different discharge pressure and with different types of water mist systems were investigated. Experimental results showed that the cooking oil underwent a substantial expansion in volume during heating. The fires developed quickly once the oil auto-ignited. The fire growth rate was affected by the oil depth in the pan and the hood position in the oil cooker. The water mist fire suppression systems effectively extinguished large cooking oil fires and prevented them from re-igniting. Their extinguishing performance was determined by the type of water mist system, discharge pressure and hood position in the oil cooker.     

A study of the probability distribution of pool fire extinguishing times using water mist

Water mist, a replacement for Halon gaseous agents in fire fighting, has been studied for decades. However, the fire-extinguishing reliability of water mist is debated. For example, there are significant differences in extinguishing times between tests conducted under the same conditions, and water mists have difficulty extinguishing small fires. To date, no study of the probability distribution of extinguishing times has been reported. In this study a statistical analysis of the extinguishing time distribution of pool fires extinguished using water mist is presented. The fire sources were circular/square stainless steel pans with gasoline, diesel, ethanol or daqing RP-3 as fuel. Two types of extinguishing scenarios were observed. In one situation, the fire was extinguished via a blow off process, when the flames had not yet been suppressed. Flame cooling is the primary fire extinguishing mechanism; the mass loss rate and combustion heat of the fuel are two key factors. In the other situation, the fire was initially suppressed and subsequently extinguished after a long suppression stage. Surface cooling is the primary fire extinguishing mechanism; the flash point of the fuel is the key factor.     

障碍物遮挡条件下细水雾与油池火相互作用的实验研究

障碍物影响下细水雾灭火有效性的研究具有重要的意义。研究了障碍物与火焰的相对位置、细水雾工作压力、喷头距离火焰垂直距离及水平距离等因素对灭火有效性的影响,以及细水雾作用下火灾烟气中一氧化碳、二氧化碳及氧气浓度的变化规律等。结果表明:高压细水雾可以有效扑救部分有障碍物遮挡的油池火,同时喷头距离火焰的水平距离和垂直距离也显著影响着细水雾的灭火速度;高压细水雾在灭火过程中火场的氧气浓度明显升高,二氧化碳和一氧化碳浓度明显降低;细水雾工作压力较低时,一氧化碳浓度反而有所增加。     

细水雾灭油池火时各种影响因素的相对重要度分析

采用实验的方法并与理论分析相结合，对细水雾在扑灭B类火时，占主导地位的灭火机理进行了研究。实验中发现，当液体燃料的闪点相差较大时，其灭火机理往往不尽相同。并且当细水雾的雾特性相差较大时，在灭火中起主导作用的灭火机理常常也各有不同。因而那种单纯以雾滴的粒径分布作为细水雾扑灭燃料闪点较高的油池火时，雾滴的动量分布对细水雾的灭火有效性影响更大。为此，本文还建立了一个简单的模型，试图得到在这种火灾场景下，对细水雾灭火的临界动量要求。     

细水雾对油池火热释放速率影响规律的实验研究

热释放速率是描述火灾现象的重要参数,可以表征火灾发展的强烈程度。利用大尺寸的热释放速率实验测量平台开展细水雾对不同种类油池火灭火效率的实验研究,同时分析细水雾对燃烧产物一氧化碳含量的影响。结果表明,热释放速率曲线能直接反映出细水雾对火源的作用,细水雾作用下三种燃料的热释放速率均被有效抑制,且细水雾的流量越大,对油池火的灭火效果越好。燃烧产物一氧化碳在施加细水雾时出现陡增,表明细水雾隔绝氧气,造成不完全燃烧或者燃烧熄灭。     

Experimental study on fire suppression performance of the high pressure water mist in the engine room of an offshore platform

The total flooding application water mist system is a new type of environmentally-friendly fixed extinguishing system. The optimizing design can improve its fire extinguishing performance. At present, the water mist fire extinguishing system in the engine room of the offshore deepwater semi-submersible support platform has not attracted sufficient attention. In this paper, the water mist in the engine room of a deepwater semi-submersible support platform was studied. It contains the effect of water mist on the heat absorption and oxygen insulation of diesel pool fires. The applicable parameters of the water mist fire extinguishing system were also determined. Moreover, based on the shielding of the fire source in the engine room and the different requirements for water mist extinguishing parameters, a hierarchical multi-parameter combined high-pressure water mist fire extinguishing system was proposed. In the full-scale experimental engine room model, according to the fire extinguishing experiments for diesel pool fires with different areas, this kind of hierarchical multi-parameter water mist system is very effective on shielded and non-shielded fires. In addition, it is still effective even in a non-closed environment coupled with smoke exhausting.     

Performance evaluation of a water mist system in semiconductor wet bench fires

Wet benches are typically utilized in semiconductor facilities for wafer and parts cleaning. Heaters and some flammable liquids, such as acetone and isopropyl alcohol (IPA), are employed during the cleaning process. Wet bench fires have caused serious losses in the semiconductor industry. To assess the fire protection performance, several field tests were performed using a water mist system installed in the wet bench. In this study, acetone pan fuel was used as fire source. The test parameters were operational pressure, pan size, nozzle location, cylinder obstruction and degree of door closure. An appropriate design for operating pressure and the location of water mist nozzles extinguished wet bench fires effectively in the early fire stages. The nozzles are suggested to be fixed above or on the each side of the pan, ensuring that mist can completely cover a pan surface with sufficient momentum. With this suggested design, fires can be extinguished in the pan and do not spread over the wet bench.     

细水雾扑灭油池火过程中火焰强化现象的实验研究

在细水雾扑灭油池火的初期,某些油池火焰会有一个突然强化、剧烈燃烧的情况发生。通过实验研究证明,酒精等与水互溶的液体不会发生强化现象,汽油和柴油等不溶于水的液体则有明显的强化现象;同时,发生强化现象的根本原因是共沸使得细水雾到达燃料表面后急剧沸腾而强化燃烧。