接种物对厌氧同步脱硫反硝化特性的影响实验研究

分别以厌氧污泥、脱氮硫杆菌菌悬液和厌氧污泥并添加脱氮硫杆菌菌悬液为接种物,以硫化物和硝酸盐为进水基质,考察不同接种物条件下,各反应器的硫化物氧化特性、反硝化特性、生化反应机理及微生物特性。结果表明,在无菌条件下,硫化物不能被硝酸盐化学氧化。接种脱氮硫杆菌菌悬液的2#反应器的硫氧化速率为1.98 g S/(m3.h),停留24 h硫化物的去除率高达97%,脱硫能力最强,该接种条件下以硝酸盐氧化硫化物为主反应,优势菌为杆菌,进水的NO3--N/S应控制在0.4以下,可以实现高效生物脱硫。接种厌氧污泥的1#和3#反应器的脱氮效果比2#反应器好,停留时间为24 h时,硝酸盐的平均去除率为96%。单独接种厌氧污泥的1#反应器的硫氧化速率为1.78 g S/(m3.h),其优势菌为球菌,该接种条件下以硝酸盐氧化硫化物和硝酸盐氧化单质硫为主反应,进水的NO3--N/S应控制在0.8左右。以厌氧污泥联合脱氮硫杆菌为接种物时,硫氧化速率为1.71 g S/(m3.h),反应器以硝酸盐氧化硫化物、硝酸盐氧化单质硫以及异养反硝化为主反应,驯化后优势菌为球形、卵圆形和短杆状,应控制进水NO3--N/S为1.2,可以实现同步脱硫反硝化,该工艺既可以用于含硫废水的处理,也可以用于C/N低的硝酸盐废水的处理。     

接种不同污泥源条件下厌氧氨氧化菌的特性

2组ASBR接种污泥源分别为好氧硝化污泥、好氧硝化污泥和厌氧氨氧化污泥按2：1比例}昆合的混合污泥。在相同条件下，经过驯化培养均实现了厌氧氨氧化的稳定运行。接种好氧硝化污泥的反应器的适应期为29d，经过105d的培养反应器成功启动；接种混合污泥的反应器的适应期为13d，经过49d反应器启动成功。从2组ASBR污泥中提取细菌总DNA，经过厌氧氨氧化菌特异引物Pla46rc／Amx820对污泥样品进行PCR扩增、克隆和测序等分析。实验结果表明，接种不同污泥源条件下的反应器中厌氧氨氧化菌的特性存在差异，接种污泥源为好氧硝化污泥的反应器中存在的厌氧氨氧化菌种为CandidatusKuenenia，而接种混合污泥的反应器中存在的厌氧氨氧化菌种为CandidatusAnammox—oglobus，与最初接种的混合污泥中的厌氧氨氧化菌相同。当接种污泥中存在厌氧氨氧化菌时，该菌株经过长时间的驯化可成为优势菌种，而当接种污泥中无厌氧氨氧化菌存在时，CandidatusKueneniasp．可以在反应器中占主导，具有更强的竞争优势。     

上流式厌氧污泥床反应器中厌氧氨氧化脱氮性能的研究

研究了上流式厌氧污泥床(UASB)反应器中厌氧氨氧化工艺的脱氮性能。接种体积比为1∶1的已驯化半年的厌氧氨氧化污泥混培物和城市污水处理厂回流污泥,采用提高基质浓度和缩短水力停留时间(HRT)2种方式提高UASB反应器的脱氮性能。结果发现,2种方式结合可在UASB反应器中获得较高的脱氮速率,经过280d后,最高总氮去除速率达到5.16kg/(m3·d)。缩短HRT并未对UASB反应器的脱氮效果产生不良影响,反而强化了脱氮性能。HRT由0.4d缩短至0.2d时,总氮去除速率由1.89kg/(m3·d)增加到3.66kg/(m3·d)。形成的颗粒污泥中的细菌的细胞形态不规则,内部有厌氧氨氧化体,为典型厌氧氨氧化菌结构特征。污泥的比基质转化速率为3.15kg/(kg·d)。经16SrDNA检测,污泥中的厌氧氨氧化菌属于"Candidatus Kuenenia"属。     

高温厌氧膨胀颗粒污泥床反应器处理聚氯乙烯离心母液废水启动方法

采用高温厌氧膨胀颗粒污泥床(EGSB)反应器处理低浓度、难降解聚氯乙烯(PVC)离心母液废水,以天津市经济技术开发区污水处理厂序批式活性污泥法(SBR)工艺好氧污泥和生物接触氧化法处理PVC离心母液废水污泥的混合污泥为接种污泥,以葡萄糖模拟废水为基质,不断增加PVC离心母液废水所占比例的方法驯化厌氧微生物,实现了系统的成功启动。系统启动期间,进水有机负荷(以COD计)和水力停留时间分别保持在0.2 kg/(m3.d)和50 h左右,出水COD去除率和pH分别稳定在80%和8.0左右。结果表明,添加共代谢基质能利用基质间的协同作用缓解有毒物质对微生物的毒性作用,显著提高了废水的可生化性。通过采用改变水质、保持稳定负荷实现EGSB反应器处理PVC离心母液废水的成功启动证明,该启动方法具有良好的稳定性和可靠性。     

好氧硝化颗粒污泥的培养及其性能

为考察不同接种污泥培养好氧硝化颗粒污泥的可行性,分别采用絮状活性污泥和厌氧颗粒污泥作为接种污泥,在气升内循环序批式反应器(SBAR)中进行好氧硝化颗粒污泥的培养,探讨不同性质的种泥对好氧硝化颗粒污泥的培养及其性能影响.结果表明,以絮状活性污泥、厌氧颗粒污泥为接种污泥均可培养出好氧硝化颗粒污泥,其颗粒成熟时间分别为62和80 d,SVI为25.52和27.68 mL/g,氨氮去除率为93.15％和75.43％,COD去除率在90％以上,SOUR、Zeta和EPS显著提高,微生物活性及疏水性能增强,以絮状活性污泥培养的好氧硝化颗粒污泥性能更优.     

厌氧颗粒污泥启动复合式厌氧折流板反应器的研究

研究以厌氧颗粒污泥接种的复合式厌氧折流板反应器(HABR)启动：在HABR中直接接种厌氧颗粒污泥，以退浆废水为试验进水，在系统水力停留时间为168 h,中温(32±1) ℃，进水pH值6.5～8，碱度适当偏高条件下，进入反应器废水COD浓度由1 800 mg/L逐渐提高到13 520 mg/L，运行60 d后系统COD去除率最低为45%，并且保持稳定，出水pH值和碱度相对比较稳定，污泥明显呈颗粒状，反应器启动完成。反应器可以在短时间内重新启动，污泥活性很快得到恢复。     

大型UASB处理阿维菌素废水厌氧污泥颗粒化研究

采用大型UASB反应器处理阿维菌素废水,接种好氧絮状污泥,经过189 d运行,成功实现了厌氧污泥颗粒化.通过调节反应器进水水质控制进水中阿维菌素浓度和长时间培养驯化,阿维菌素对厌氧消化的抑制影响基本消除.UASB反应器进水pH值4～5、COD 8890～12 100 mg/L、容积负荷达到10.5 kg COD/m3·d,COD去除率稳定在85%以上,出水COD为1308～1670 mg/L.     

以养殖固体废弃物发酵产物为碳源的SND系统的脱氮除磷效果

在连续低曝气的SBR装置中,采用人工模拟养殖废水培养成熟脱氮除磷污泥,研究了养殖固体废弃物发酵产物为碳源的养殖废水脱氮除磷效果。结果表明:在水力停留时间(HRT)为12 h,溶氧在0.04~1.5 mg/L之间,污泥经过25d的驯化培养,反应器中形成了具有较高活性的同步硝化反硝化能力的污泥,以养殖固体废弃物发酵产物为碳源处理养殖废水,反应器中的COD、NO-3-N和NH+4-N最大去除率分别能达到97.87%、94.95%和88.90%,且NO-2-N完全不发生累积,其中C/N=7.35,即50 g湿重的养殖固体废弃物与2 L的养殖废水配比最佳,脱氮除磷效果最好,对TN的去除率在87%左右,能够较好完成同步脱氮除磷实现养殖固体废弃物的资源化利用,为循环水养殖系统零排放提供技术参考。     

厌氧产氢ASBR对氮的脱除

在厌氧序批式人工有机污水生物产氢反应器(ASBR)中发现氮"丢失"现象,并对此产氢系统发生脱氮作用的机理和主要影响因素进行了研究。结果表明,在以葡萄糖为发酵底物的厌氧产氢系统中,微生物分别以铵和硫酸盐为电子供体和电子受体发生了硫酸盐型厌氧氨氧化;进水有机物负荷和pH主要通过影响不同种微生物的活性而影响脱氮性能,氨氮和硫酸盐的浓度直接与氮素去除率有关。在最大产氢能力为16 m3/(m3·d)、氢气体积百分比为65%的生物制氢系统中,最大脱氮效率约为64%。产氢效率与氮脱除率呈现负相关关系。研究表明,在控制条件下,可以实现高有机物废水厌氧脱除氨态氮,为生活污水直接厌氧脱氮开辟一条新途径。     

分子生态技术对厌氧脱氮除磷微生物优势菌群的鉴定

应用分子生态克隆技术,直接对A/O反应器所驯化培养的厌氧脱氮除磷微生物样品进行主要功能菌群的分子生态学鉴定。通过克隆文库的序列分析,发现驯化培养后厌氧污泥样品中的优势菌群主要是Azospirillum和Selenomonas两个属。这一结果表明,厌氧反应器中的某些红螺菌科和氨基酸球菌科的微生物,可能是在厌氧条件下对氮磷同时降解起关键作用的功能菌群。     

IC反应器处理高浓度硫酸盐废水的启动研究

采用木糖生产废水,进行了(IC)反应器处理高浓度硫酸盐有机废水的启动研究.结果表明,接种厌氧颗粒污泥,当进水COD/SO2-4值约为3.5时,控制COD负荷提高幅度为每次20%左右,经过26 d的驯化培养,COD和SO2-4负荷分别可达20 kg/(m3·d)和5.5 kg/(m3·d),COD去除率达到80%以上,硫...     

Heavy metal removal from synthetic wastewaters in an anaerobic bioreactor using stillage from ethanol distilleries as a carbon source

This work was conducted to investigate the possibility of using stillage from ethanol distilleries as substrate for sulfate reducing bacteria (SRB) growth and to evaluate the removal efficiency of heavy metals present in wastewaters containing sulfates. The experiments were carried out in a continuous bench-scale Upflow Anaerobic Sludge Blanket reactor (13 l) operated with a hydraulic retention time of 18 h. The bioreactor was inoculated with 7 l of anaerobic sludge. Afterwards, an enrichment procedure to increase SRB numbers was started. After this, cadmium and zinc were added to the synthetic wastewater, and their removal as metal sulfide was evaluated. The synthetic wastewater used represented the drainage from a dam of a metallurgical industry to which a carbon source (stillage) was added. The results showed that high percentages of removal (>99%) of Cd and Zn were attained in the bioreactor, and that the removal as sulfide precipitates was not the only form of metal removal occurring in the bioreactor environment.     

Heavy metal removal from synthetic wastewaters in an anaerobic bioreactor using stillage from ethanol distilleries as a carbon source

This work was conducted to investigate the possibility of using stillage from ethanol distilleries as substrate for sulfate reducing bacteria (SRB) growth and to evaluate the removal efficiency of heavy metals present in wastewaters containing sulfates. The experiments were carried out in a continuous bench-scale Upflow Anaerobic Sludge Blanket reactor (13 l) operated with a hydraulic retention time of 18 h. The bioreactor was inoculated with 7 l of anaerobic sludge. Afterwards, an enrichment procedure to increase SRB numbers was started. After this, cadmium and zinc were added to the synthetic wastewater, and their removal as metal sulfide was evaluated. The synthetic wastewater used represented the drainage from a dam of a metallurgical industry to which a carbon source (stillage) was added. The results showed that high percentages of removal (>99%) of Cd and Zn were attained in the bioreactor, and that the removal as sulfide precipitates was not the only form of metal removal occurring in the bioreactor environment.     

苯酚的厌氧生物处理

采用不断增加苯酚浓度而降低葡萄糖浓度的方法可驯化厌氧污泥中的微生物，使厌氧污泥最终以苯酚为唯一碳源生长，可显著提高厌氧污泥降解苯酚的能力；对苯酚间歇厌氧降解过程进行了分析。苯酚浓度在0～1.680 mg/L范围内，其厌氧降解过程符合一级动力学。Aiba模型、Haldane模型和Teisser 模型均可很好地描述处于对数期时厌氧污泥的比生长速率与初始底物浓度之间的关系，其中以Teisser 模型模拟的效果最好。将驯化污泥接种于UASB中可实现对含酚废水处理的连续运行，最大的有机负荷达2 g COD/（L·d），稳定运行时苯酚的去除率可维持在96%以上。     

厌氧接触式反应器预处理高浓度丙烯酸废水

采用厌氧接触式反应器,对自配丙烯酸(AA)废水进行预处理.反应器经污泥驯化稳定运行后,在HRT为12h,进水丙烯酸浓度为1000～3 000 mg/L,丙烯酸容积负荷为2～6 kg AA/(m3·d),污泥负荷为0.67～2.00kg AA/(kg VSS·d)的条件下,丙烯酸去除率达95%以上,出水丙烯酸浓度低于16...     

Biogas production from anaerobic digestion of food waste and relevant air quality implications

Biopower can diversify energy supply and improve energy resiliency. Increases in biopower production from sustainable biomass can provide many economic and environmental benefits. For example, increasing biogas production through anaerobic digestion of food waste would increase the use of renewable fuels throughout California and add to its renewables portfolio. Although a biopower project will produce renewable energy, the process of producing bioenergy should harmonize with the goal of protecting public health. Meeting air emission requirements is paramount to the successful implementation of any biopower project. A case study was conducted by collecting field data from a wastewater treatment plant that employs anaerobic codigestion of fats, oils, and grease (FOG), food waste, and wastewater sludge, and also uses an internal combustion (IC) engine to generate biopower using the biogas. This research project generated scientific information on (a) quality and quantity of biogas from anaerobic codigestion of food waste and municipal wastewater sludge, (b) levels of contaminants in raw biogas that may affect beneficial uses of the biogas, (c) removal of the contaminants by the biogas conditioning systems, (d) emissions of NO_x, SO₂, CO, CO₂, and methane, and (e) types and levels of air toxics present in the exhausts of the IC engine fueled by the biogas. The information is valuable to those who consider similar operations (i.e., co-digestion of food waste with municipal wastewater sludge and power generation using the produced biogas) and to support rulemaking decisions with regards to air quality issues for such applications.

Implications: Full-scale operation of anaerobic codigestion of food waste with municipal sludge is viable, but it is still new. There is a lack of readily available scientific information on the quality of raw biogas, as well as on potential emissions from power generation using this biogas. This research developed scientific information with regard to quality and quantity of biogas from anaerobic co-digestion of food waste and municipal wastewater sludge, as well as impacts on air quality from biopower generation using this biogas. The need and performance of conditioning/pretreatment systems for biopower generation were also assessed.     

EGSB反应器处理产氢发酵液

以厌氧颗粒污泥为接种污泥，对厌氧颗粒污泥膨胀床（EGSB）反应器处理产氢发酵液的启动性能进行了研究。结果表明，在温度为（35±1）℃，水力停留时间（HRT）为6h的条件下，逐渐提高进水COD，经过40d连续运行，EGSB反应器启动成功。容积负荷达到14kgCOD／（m3·d）时，COD去除率约为80％，产气量为26．84L／d，甲烷含量为57．9％。     

厌氧产氢ASBR对氮的脱除

在厌氧序批式人工有机污水生物产氢反应器（ASBR）中发现氮“丢失”现象，并对此产氢系统发生脱氮作用的机理和主要影响因素进行了研究。结果表明，在以葡萄糖为发酵底物的厌氧产氢系统中，微生物分别以铵和硫酸盐为电子供体和电子受体发生了硫酸盐型厌氧氨氧化；进水有机物负荷和pH主要通过影响不同种微生物的活性而影响脱氮性能，氨氮和硫酸盐的浓度直接与氮素去除率有关。在最大产氢能力为16m3／（m3·d）、氢气体积百分比为65％的生物制氢系统中，最大脱氮效率约为64％。产氢效率与氮脱除率呈现负相关关系。研究表明，在控制条件下，可以实现高有机物废水厌氧脱除氨态氮，为生活污水直接厌氧脱氮开辟一条新途径。